Search Documents

By Dirk van Zyl

Natural materials can be used successfully in the construction of heap leach pads. The use of these materials usually result in the least expensive approach for such facilities. Sufficient geotechnical experience has been gained in the design and construction of clay heap leach pads so that they can be used with confidence. A number of operators presently use clay pads in their heap leach facilities; these include Alligator Ridge, Ely, Nevada (gold), and Union Carbide, Gas Hills, Wyoming (uranium). This paper describes the construction and field investigation of a clay pad for the heap leaching of agglomerated precious tailings. The project is located in the Mojave Desert, Southern California. The design had to satisfy operational requirements as well as regulatory requirements. The California Water Quality Control Board (WQCB) was one of the agencies which had to issue a permit for the project. Their biggest concern was the discharge or escape of cyanide into the environment. Rather stringent requirements were therefore placed on the pad design criteria, especially in terms of permeability.

Jan 1, 1983

By Brian W. Mackenzie

The mine development decision is made on completion of exploration to determine whether or not a mineral deposit should be developed to production and, if so, how. This involves the selection of an optimum mine development alternative from a number of technically feasible alternatives and the comparison of this optimum with those of other available investment opportunities. If the optimum is sufficiently attractive, the deposit is developed to production. The selection process is carried out within a framework of corporate objectives and resources. The mine development decision is based on the balancing of two parameters - - rate of production as reflected in plant capacity and cut-off grade. On the basis of available information and experience, detailed revenue and cost 'estimates are made for each feasible combination of plant capacity and cut-off grade. What economic evaluation techniques should be applied to these estimates to reduce each alternative to economic indicators that will enable meaningful comparisons and an informed investment decision? This is the essence of the paper. The determination of optimum plant capacity and cut-off grade has been the subject of intensive research efforts by economists and mining engineers (1-7). Their studies are based on marginal analysis and assume that, at the time of decision, certainty conditions prevail with respect to ore reserves, mining costs and mineral markets. The optimum mine development alternative is defined as that which maximizes profitability.

Jan 1, 1969

By William V. Robinson

The Iron Ore Company of Canada mines, processes and ships crude iron ore, concentrate and pellets from the rich ore bodies of the Labrador Trough area in the extreme north-eastern part of Canada, some five hundred miles from Montreal (see figure 1). There are three main sites of activity. At Schefferville, approximately 12 million tons a year of crude ore (chiefly limonite) are mined, crushed, screened and shipped to Sept-Iles. At Labrador City, 40 million tons of specular hematite are mined annually for processing into 17 million tons of concentrate. Of this, 9 million tons are converted into pellets. All product 1s shipped to Sept-Iles. At Sept-Iles, on the north coast of the St. Lawrence, a six million ton per year concentrator and pellet plant process much of the Scheffervllle ore into high-grade pellets. Also at Sept-Iles are the company's administration offices stockpiles and shipping facilities. The Terminal facilities can berth and load a 250,000 ton bulk carrier at 19,000 tons per hour.

Jan 1, 1975

By G. W. Cutting

Interlocking material balances on complex mineral dressing plants greatly assist in metallurgical investigations: indeed, without such a balance, there is no firm basis upon which to base process performance evaluations. To achieve balances both qualitative and quantitative data must be rationalised in conjunction with the process flowsheet. WSL has developed a range of programs to evaluate interlocking material balances. However, to obtain maximum benefit from the balances, answers of direct value at the process level must be provided: WSL has developed also a range of programs for this purpose. Practical examples are given, which illustrate the benefits obtained from process balances.

Jan 1, 1979

By Koehler Stout

Stopewall or room closure can be a problem in nining operations. In some mines, wall closure causes ore passes and nanways to collapse when they are enclosed in nine fill. When this phe- nomena occurs, heavy ground and, or, rock bursts frequently happen. Often, ground problems become progressively worse as mining in the stope block progresses toward the upper level. The sill and pillars in the level above may experi ence heavy ground and bursts. Sometimes the conditions get so bad in the stope that it is unsafe to mine the ore, so the stope is abandoned and the ore is lost.

Jan 1, 1980

By W. J. Atkinson

Since the inception of the Ashton (formerly Kalumburu) Joint Venture in 1972 the parties have expended 524 million in exploration for diamonds in the Kimberley region. This has resulted in the discovery of the currently subeconomic Ellendale deposits in 1976/77 and the economic Argyle - Smoke Creek Deposits in 1979/80. In addition to Argyle and Ellendale some 90 kimberlitic and lamproitic bodies have been discovered grouped broadly into three provinces, on the west, east and north margins of the Kimberley block. These bodies range in size from dyke-like features less than one metre in width to pipes with a surface area of 128ha. The bodies with larger surface area are volcanic crater deposits, infilled with air-fall and water deposited tuffs and epiclastic sediments.

Jan 1, 1984

By H. Colijn

Vibratory or oscillatory conveyors can be found in all types of industry, handling virtually any granular bulk material, often at elevated temperatures. These conveyors can be combined with other process functions, such as screening, cooling, drying and dewatering, while conveying. Although construction and installation is relatively simple, the engineering and design analysis of the vibratory mechanics is fairly complex. This paper will discuss the basic types of vibratory conveyors and the analysis of the material movement along the carrying trough.

Jan 1, 1985

By Elmer H. Citron

The Monterey Coal Company, a wholly owned subsidiary of The Carter Oil Company of Houston, Texas, recently awarded a contract to build the Monterey No. 1 Preparation Plant, which will be located near Carlinville, Illinois, to the McNally Pittsburg Manufacturing Corporation. The preparation plant will be one of the most modern jig preparation plants in the State of Illinois. Illinois No. 6 coal will be delivered by a 48" slope belt having 35-degree carrying idlers, operating at 650 FPM and operating on an incline of nearly 17 degrees. The slope belt is driven by two 450 BP motors and will deliver the mined coal at the rate of 1800 TPH to a stationary step-type ' screen having six-inch openings. The overproduct from the stationary screen will discharge into a 10' x 24' McNally Rotary Breaker and the underproduct will bypass the rotary breaker. The rotary breaker is equipped with heavy manganese screens with 6 ½" diameter openings. The sized 6" x 0 coal from the stationary step screen and the rotary breaker will be discharged by gravity to a 4%" raw coal incline storage belt. The 48" raw coal storage belt will deliver the 6" x 0 sized coal at the rate of 1800 T?H to an 8000 ton concrete raw coal silo, 70 feet in diameter and 1x7 feet high. The 6" x 0 sized coal will be drawn from the concrete storage silo by seven (7) 36" wide reciprocating plate feeders. Five feeders are to have constant speed drives at a rated capacity of 145 TPH each. Two (2) feeders will have remote con- trolled variable speed drives, to provide a varying feed.

Jan 1, 1970

By Richard L. Ash

Usually stresses generated by explosive charges during blasting are considered to propagate through materials in a spherical manner. Although conical stress-waves had been suggested by a few investigators they have never been clearly defined or critically observed. An experimental technique using models and lengths of Mild Detonating Fuse was developed to produce conical stress-waves and study their effects. Several materials with different properties were tested to compare the influence of those properties on wave shape and crater formation. The investigations showed that whenever column charges were end-initiated, conical stress-forms were produced if the explosive's velocity exceeded the energy propagation velocity of the surrounding material. The stress-cone angle significantly affected fragment size and shape as well as the geometry of craters produced.

Jan 1, 1967

By Madan M. Singh

With the current emphasis on ecology, safety, and conservation of natural resources, some consideration should be given to methods of mining that reduce surface damage, make the mining of coal less hazardous, and allow exploitation of a larger percentage of the coal in situ. One method that can be helpful toward attaining these objectives is the use of packing or stowing. Stowing involves the replacement of the ore that has been removed by waste material obtained from within the mine or elsewhere. Evidently, it would be most beneficial if this waste for packing were available from the mine being worked, but generally this is not possible. If complete stowing is adopted, it is necessary to bring in packing material from other sources. Stowing tends to reduce surface subsidence, but not eliminate it. It enhances roof support and curtails accumulation of methane in the gob, making the mining operations safer. It may also allow one to obtain a larger amount of coal. Currently, in the United States, a substantial amount of coal is left in place as pillars, in the hope that it will support the overburden indefinitely. Some of these could be extracted with stowing. The mining of thick, steep, or contiguous seams would also be facilitated.

Jan 1, 1974

By F. J. Hurst

Phosphate rock, which is a prime source of phosphate used in fertilizer manufacture in the United States, contains uranium. In general, the uranium content of the rock increases with the phosphate content and most high-grade phosphate deposits (>30% P2O5) contain 0.01- 0.02% U3 8. The large tonnages of rock being mined represent a significant potential source of uranium that lends itself to recovery as a by-product of the wet-process phosphate industry. For example, in 1953, the U. S. Geological Survey estimated that recoverable phosphate reserves in the U. S. totaled about 5 billion tons and contained 600,000 tons of uranium. I This estimate did not include any rock from North Carolina which has since been estimated at about 2 billion tons. For the most part, the known, economically mineable U. S. reserves - estimated at about 7 billion tons - are concentrated in a few areas: 43% in the western states of Idaho, Montana, Utah and Wyoming; 28% in each of Florida and North Carolina and less than 1% in Tennessee. In the past, Florida has supplied about 80% of the total U. S. production, practically all of which is land pebble phosphate. All forecasts indicate increased production rates from North Carolina and the western states.

Jan 1, 1976

By Meyer Klein

Decision theory is the formal theory of the logic of decisions in view of the decision maker's objectives, preferences, I beliefs, and available information, It usually deals with weighty economic problems involving irrevocable (or costly to reverse) decisions. Capital investment planning problems constitute an instance par excellence for application of the decision theory concepts. Decision theory as it is presently conceived has evolved in recent years. At first it concentrated on decisions in the face of total lack of information and on games with intelligent adversaries. The results of these efforts proved theoretically interesting, but practically of little applicability. In the last few years, stress has shifted to the introduction of subjective probabilities and preferences, and the results have been eminently successful in applications both in government and with- in business firms in the resolution of complex problems.

Jan 1, 1970

By Richard L. Ash

In many instances, blasting exerts the dominant control over the economics and safety of excavation, where the materials involved are too hard and tough to be fragmented efficiently by other means. However, associated with the fragmentation process other effects very often result that are not desirable and may even be hazardous, such as fly rock, air blast, excessive overbreak, and damaging ground virbrations. It has always been the desire of those concerned with blasting to better control the forces involved so as to improve the breakage of materials, but at the same time reduce, or eliminate if possible, the unwanted side effects. Until the last decade or two, little was known of the phenomena concerned with blasting. However, since that time many investigators have studied blast mechanisms produced from both chemical and nuclear explosions, with the result that general concepts of the principles have been developed. But, in general, it is assumed that the energy from the explosion would be propagated spherically throughout the material, the latter of which for convenience of analyses is considered homogeneous and isotropic, i.e., the properties are the same in all directions, However, rocks are not isotropic as a rule, and evidence clearly indicates blasting forces rarely function uniformly or in spherical form as theorized.

Jan 1, 1965

By J. D. Miller

Physical separation of bitumen from low-grade Utah tar sand deposits containing a relatively high viscosity bitumen phase (Sunnyside and Tar Sand Triangle deposits) has been accomplished by traditional size reduction and froth flotation techniques. At appropriate experimental conditions more than 90 percent of the bitumen can be recovered in a concentrate, containing more than 20 weight percent bitumen, which should be a suitable feed material for subsequent hot water or thermal processing. The efficiency of bitumen recovery depends on the extent of size reduction, promoter and dispersant addition. Rejection of greater than 60 percent of the sand at ambient temperature and ease of water removal from the concentrate make such a process strategy both energy and cost effective. The energy required to achieve effective separation by the ambient temperature process is significantly less than the energy required for the recently developed hot water process. The flotation behavior of the tar sand has been analysed with respect to flotation pH, contact angle measurements and the apparent iso- electric point of the bitumen. The best flotation response at pH 7.8 to 9.0 can be correlated with the maximum in contact angle developed between the air bubble and bitumen surface and with the apparent iso-electric point of the bitumen (-pH 8.0).

Jan 1, 1981

By Lawrence Adler

The properties of a geologic mass may be considered from a resource or an engineering viewpoint. The primary engineering applications include ground control, excavation, bulk handling, and hydrology. This study will focus upon these areas in descending order. For an adequate geologic description, data is necessary on the following components: (1) the intact rock, (2) geologic structures, (3) contained fluids, and (4) existing pressures and temperatures, see Table 1. This information, combined with the engineering specifications, provides the basis for a formal geotechnical analysis as illustrated in Figure 1. For a structural analysis it is essential to establish the mechanical properties of the material composing the structure. This material, termed the "rock mass," consists mainly of the first two geologic components, the intact rock and geologic structures (Figure 1) Consideration of fluids will be subordinated to their role as chemical agents affecting the mechanical properties. The existence of pressures and temperatures generally lies beyond the scope of this study.

Jan 1, 1973

By J. E. Jennings

The problems of slope stability in open-cast mines are examined. A criterion, the instantaneous stripping ratio, is suggested for use in the design of pit slopes and as an index of control at all stages of the exploitation of the ore body, This criterion may also be related to safety and to the maximizing of profits. Two approaches to safe design of slopes, one from the point of view of soil mechanics and the other from the point of view of rock mechanics, are described and critically compared. The effect on slope stability of the regional tectonic stress field is discussed. Explanation is given of the application of the Terzaghi effective stress concept to problems in both soil and rock environments, including possible effects when borehole deformation techniques are used to measure stresses in rock in situ.

Jan 1, 1963

By T. D. Wheelock

The effect of various flotation depressants and surface treatments on the floatability of coal derived pyrites in the presence of XIBC was investigated with a modified Hallimond tube microflotation cell. The floatability of pyrite particles which had been cleaned with hot dilute (5%) hydrochloric acid was relatively large. However, the floatability of such particles was reduced greatly by the addition of specific depressants such as calcium hydroxide and also by treating the pyrite with an aerated warm alkaline solution. Although this treatment and these depressants also had some effect on the floatability of coal particles, the effect was much less than on the pyrite particles.

Jan 1, 1979

By Walter H. Schwedes

Ore grinding mills are really just slowly rotating barrels, but barrels that are growing in size so fast that the application of electric drives for them is rapidly approaching a technology like that for wind tunnels or pumped storage drives. This application is particularly worthy of care because some 40% of the 75 megawatts of power used by a large copper ore concentrator, or some 60% of the 200 megawatts supplied to a large iron ore concentrator, are for grinding. These ore plants are located where the ore is, not where a utility happens to be. So, the challenge is not only to choose a drive and .power transmission for reasonable cost, high performance, reliability and minimum maintenance, but to afford the interface between mill drive and power distribution and source systems to minimize the whole ore plant's monthly power bill, or costs of self generation. Conclusions can be reached in optimizing a drive selection only for each particular ore plant's set of parameters, but by identifying the criteria for selection and then weighting each type of drive per criteria, yardsticks for final choice become apparent. This is the purpose of this paper. Grinding action takes place inside the barrel, where the ore charge is ground with the aid of balls, or mill length rods, or large chunks of ore as in autogenous grinding.

Jan 1, 1972

By Walter von der Linden

On April 14, 1975, Consolidation Coal Company began to operate a longwall face in their Shoemaker Mine using shield supports. This was the first time that shield supports were used in the United States (1) 1/. Shortly thereafter, Kaiser Steel Corporation started a shield longwall face at their York Canyon Mine (2). From October 1975 through May 1976, three more longwall faces were commissioned in mines located in south-western Pennsylvania and northern West Virginia. In June 1976, four installations had completed their first panel and two installations had completed the subsequent move to the second panel where coal production is now well under way. During this time (April 75 to June 76) the total number of shield support face operating months, including moving time, was 40 and the combined face advance was approx. 17, 000 feet (5200 m) with face lengths varying from 450 - 550 feet (137 - 168 m). While the shield support experience in the U.S. is still limited on the basis of time and mining parameters, the operating results of all faces have been very satisfactory. New record 24 hr production figures were set and - far more important - long term production figures could be sustained on an impressively high level even when taking face moving time into account. The purpose of this paper is to review the performance of shield type supports in the U.S. and to assess their value as longwall supports for U.S. underground mining conditions with regard to roof control, maintenance, operator convenience, safety and productivity.

Jan 1, 1976

By Frederick P. Agterberg

It can be useful to model the mean grade values for a metal in mineral deposits containing that metal as representing the extreme value tail of a lognormal frequency distribution for the concentration values of the metal in rocks of all types. Results for copper and zinc in the Abitibi area of the Canadian Shield are compared to results previously obtained for the Canadian Appalachian Region. The lognormal model is also applied to a set of 162 large gold deposits in the Abitibi area. In the second part of the paper, 1311 large and small gold deposits in the Abitibi area are modelled as discrete events. By means of a newly developed spatial clustering model it is possible to predict the variances of random variables for frequencies of deposits in cells of different sizes.

Jan 1, 1979