Search Documents

By C. A. Rawlins, P. Rostami

"Ventilation systems are not only an integral part of any underground mine design but are a significant contributor to the mine’s capital and operating costs. The ventilation and cooling design systems presented in this paper were part of the prefeasibility evaluation of an underground platinum mine in South Africa. The mine would ultimately operate at the depth of 1,200 m below surface with a proposed 4 Mtpa production rate. The proposed mining operation is a highly mechanized operation using diesel equipment. Significant daily production rate, large amount of equipment and expansive nature of the operation, contributed to a challenging while flexible ventilation design requirements. This paper presents how to safely and efficiently optimize capital expenditure and operating costs associated with the mine air cooling and refrigeration system through practical ventilation design practices. Successful capital and operational savings by modulating installation and commissioning of refrigeration facilities can influence the economic realization of such systems. The adapted planning and design approach provided a cost-effective advantage while complying with design safety and regulations. INTRODUCTION This paper outlines a prefeasibility evaluation of the heat loads and related cooling system to be employed at the proposed platinum mine. The paper also provides appropriate details for a comprehensive understanding of the applied methodology. The proposed mine will be a trackless underground operation using a combination of mining methods. Initially, ore zones with vertical thicknesses greater than or equal to 18 m will be mined using the long-hole stoping (LHS) method, while thinner ore zones will be mined using mechanized drift-and-fill or drift-and-bench methods; hence, a highly mechanized operation with LHDs, trucks, drill rigs, personnel carriers, etc. is envisioned. Broken rock (ore and waste) will be transported by the means of trucks to the main passes (ore and waste) and collection points. Mining zones identified in the project occur at depths ranging between approximately 700 m to 1,600 m below surface. Primary access to the mine will be via a 1,100 m deep, 10 m diameter production shaft (named Shaft No. 2), three additional shafts will be sunk to provide future ventilation and production support. Three main access levels are established as primary haulage levels and include a series of interconnecting ramps. Additional mining sublevels will be developed as necessary. Figure 1 shows the proposed shaft locations and main access levels in a 3-D elevated view. Mining is performed using highly productive mechanized methods. For this reason, an annual ventilation estimate is based on requirements for mobile equipment (i.e., 0.06 m3/s/kW). The air requirements imposed on the underground operation is further influenced by equipment heat loads, auto compression, and virgin rock temperature, as the main sources of in-mine heat."

Jan 1, 2015

By C. Roos

"Mining companies have included quantifying uncertainty, or at least risk, as a requirement of project justification for many years. However, many times this process lags behind the traditional mine planning process and the results are rarely used to improve the plan. Nearly every parameter used in a mine plan is an estimate and the mine planning engineer should recognize, and even embrace, the inherent uncertainty in those parameters and its effect on their forecast results. While many of the uncertainties are beyond the scope of the traditional mine plan (e.g. global market uncertainty, socio-political uncertainty, environmental uncertainty), some uncertainties can, and should, be included in the mine planning process.Many mining engineers have incorporated techniques such as Monte Carlo Simulation or Discrete Element Simulation to understand the range of productivity that can be expected for an operation, but most still rely upon one estimated model for what is likely the critical component of technical uncertainty, the geologic resource. Modern geostatistical methods can provide multiple orebody realizations to provide a thorough unbiased picture of the geologic uncertainty. However, most traditional mine planning techniques are not formulated to allow for multiple (100-200) realizations of each material quality/grade parameter.Commercial software companies and research groups are progressing with development of tools that can incorporate geologic uncertainty, and even optimize extraction plans in the uncertain environment. Unfortunately, this author believes that a significant number of mining operations will not be able to adopt these techniques due to the computational requirements of the advanced techniques and the costs associated with implementing proprietary software. In an attempt to encourage mining engineers to embrace the inherent uncertainty in their mine plans, this article presents a cost-effective alternative that can be developed in-house, at any mine, to schedule mid- to long-term mine plans while continuously monitoring the uncertainty in the results. The aim of this article is that by demonstrating the usefulness of such a system, mining companies will encourage engineers, geologists and geostatisticians to find ways to incorporate this powerful data into their processes and procedures."

Jan 8, 2017

By H. Kinilakodi

In 2008, the authors developed a methodology for identifying underground coal mines at high risk for major-hazard events. It focused on major hazard-related violations of safety standards associated with high-risk conditions. Later, using a sample of 103 mines with 2008 and 2009 data, injury measures and U.S. Mine Safety and Health Administration (MSHA) citation data were combined into a safe performance index (SPI). The SPI was used to assess the relative safety-related risk of mines, including by mine-size category. In this paper, comparisons are made of SPI-associated, normalized safety performance measures across mine-size categories, with emphasis on small-mine safety performance as compared to large and medium-sized mines. Mining Engineering, 2011, Vol. 63, No. 10, pp. 73-77. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Q. Dai

In order to float coarse sylvite particles, Potash Corporation of Saskatchewan Inc. (PCS) uses amines and extender oil (Esso 904 oil). Since the content of polycyclic aromatic (PCA) compounds in Esso 904 oil is high, PCS has sought a suitable replacement. Various types of physicochemical tests, including measurements of the electrokinetic potential of emulsified oil droplets, oil/water interfacial tension and wetting of KCl plates by oil, did not provide conclusive results. However, captive bubble contact angle measurements on KCl plates in brine in the presence of flotation agents correlated reasonably with the flotation response. A few non-toxic oils were found to provide good results in the flotation experiments and are now tested under industrial conditions.

Jan 1, 1992

By E. R. Torak

Custom Coals, International has installed and is presently testing a 225 kg/hr. (500 lb/hr.) micronized-magnetite, fine-coal cleaning circuit at PETC's Process Research Facility (PRF). The cost-shared project was awarded as part of the Coal Preparation Program's High Efficiency Preparation Subprogram. The project includes design, construction and testing of a fully-integrated, bench-scale circuit, complete with feed coal classification to remove the minus 30 micron slimes, dense-medium cycloning of the 300 by 30 micron feed coal using three different size micronized-magnetite mediums, and medium recovery circuits using drain and rinse screens and various stages and types of magnetic separators. This paper describes the project circuit and goals, including a description of the current project status and the sources of coal and magnetite which are being tested.

Jan 1, 1996

By B. K. Mishra

The motion of the charge inside a grinding mill is of considerable practical importance. The dynamics of grinding mills have been the subject of study by a number of workers because it can accurately predict: i) the power drawn by the mill, ii) the distribution of forces inside the mill, and hence the wear rate of balls as well as the liners, and iii) mass transport of milled product through the porous ball charge. Some of the earlier analyses of the motion of a charge of particulate material in a tumbling mill were reported by White (1904), Davis (1919), and Dyer (1945) and have been reviewed by Rose and Sullivan (1958). In these works, frictional force at the wall of the mill and between the colliding balls, and the interaction of different ball trajectories, was not considered. Moreover, it was assumed that the profile of the tumbling charge is independent of the degree of filling, which is generally not true. However, all this work led to the identification of so-called "equilibrium surface" which is the plane that separates the rotating charge into two regions. The inner region is static; here there is no motion relative to the mill shell. The other region is a shear region where either the balls flow down the surface of the charge (cascading motion), or are projected out of the surface and follow approximately parabolic paths (cataracting motion).

Jan 1, 1990

By Hung-Kei H. Lam

Rubidium and cesium were discovered by Bunsen and Kirchhoff about 100 years ago. These two elements are by no means as abundant as sodium or potassium. Their occurrence in minerals is widespread, but usually as minor constituents. There is no known specific ore containing rubidium, but rubidium is found replacing the. other alkali metals in .some minerals.. Perhaps the highest concentration of rubidium found in one mineral is in lepidolite, KLi(OH,F)2A12Si3010, which contains from 0 to 3.5%*Rb20. 0n the average, lepidolite contains about 0.5% Rb20. Other sources of rubidium are carnallite, KMgCl3?6H20; pollucite, H20.2Cs20.2AI203.9SiO2; rhodizite, R20.2A1203-3B203; biotite, H2K(Mg,Fe)3A1(Si04)3; sea water, rivers, marine and fresh water organisms, soils, and plants. Cesium, even though it is the least abundant. of the stable alkalies, has a specific ore. Pollucites a hydrous cesium aluminum silicate, may con¬tain as high as 42.5% Cs20, although again, the average Cs20 content is about 25% among the handful of known deposits. Other cesium-containing minerals are lepidolite and carnallite. Rubidium and cesium are very much like potassium in chemical properties, consequently, they are hard to separate. Because of the difficulty in obtaining pure cesium and rubidium compounds coupled with the scarcity-of supply, prices were high and the two elements enjoyed little industrial use. Just before the Second World War, the world. supply of rubidium and cesium, from Germany, was a matter of tens of kilograms per year and prices were about

Jan 1, 1959

By Edward P. Larsen

At our annual meeting in St, Louis, Mo. in February 1961, we presented a comprehensive paper (No. 61-B-22) on the subject of "Blending and Handling of Materials for Agglomeration". In that paper you will find a discussion on the difference between "blending" and "mixing". With regard to "blending" we brought out the facts of its usefulness for the preparation o materials in an agglomerated mass to attain controlled chemical and physical uniformity. "Mixing" was discredited as not being useful for the attainment of uniformity of any kind.

Jan 1, 1962

By Luc Morin

What you don't know won't hurt you! This attitude can get you into trouble when considering your process! When trying to extract the most and the best possible performance from a mineral processing circuit this should be reworded to say: What you don't know about your process will hurt your profits! Today, with the popularity of joint ventures, custom milling contracts and process audits by specialists, not knowing is a formula for trouble! Good Sampling Systems are no longer considered a luxury' Not too long ago the practice of grab sampling was considered acceptable and became the norm. Today, it is rare to hear metallurgists say, "All I need is a trend not a good representative sample. so I'll just grab a sample every few hours." Buyers and sellers of quality products have found that grab sampling leads to poor partnerships'

Jan 1, 1999

By P. Rusin

A new bacterium, Thiobacillus cuprinus, can extract copper from chalcopyrite as rapidly as T. ferrooxidans. On solution with and without nutrient amendments and bacterial growth media were supplemented with T. ferrooxidans or T. cuprinus in shake flask studies. Both species extracted -42% of the copper using growth media. In one case, T. cuprinus solubilized approximately twice as much copper as T. ferrooxidans utilizing a seeded On solution. Thiobacillus prosperus also oxidizes chalcopyrite and tolerates high chloride concentrations. These sulfide-oxidizing bacteria are representatives of the mixed microbial community found in sulfide dumps. Rates of biological copper extraction from sulfide ores, using the native microbes, have been significantly enhanced by amending On solution with PGM.

Jan 1, 1994

By D. L. Lampshire

Biological leaching using native heterotrophic bacteria was studied by the U.S. Bureau of Mines as a means of extracting manganese from a domestic low-grade wad ore. Column heap leaching simulation techniques were employed using molasses as the nutrient source for the bacteria. These column studies were designed to investigate the effects of molasses medium flow rate, concentration, and replacement interval on the extent and rate of manganese extraction. .Results showed that flow rates between 0.41 and 8.1 L/min/m2 had little impact on manganese extraction. The total amount of molasses used did have a direct effect on the extent and rate of manganese extraction. Manganese extractions over 90-pct were obtained in 12 weeks of bioleaching with 2-week medium replacement cycles.

Jan 1, 1993

By K. S. Whiting

Elevated concentrations of copper, cobalt, and arsenic within the Panther Creek Basin sediments in north central Idaho prompted an evaluation of the sources of the metals. Potential tailings and waste rock source samples collected at the head of Blackbird Creek were compared to sediment samples in the Panther Creek Basin using electron microprobe techniques. The mineral types, degree of alteration, and the morphology of the metal-bearing sediment grains within Blackbird and Panther Creeks were found to consist of copper-, cobalt-, and arsenic-bearing sulfide minerals.

Jan 1, 1997

By Y. J. Wang

The Hardy Cross iterative method is the most popular technique for solving a ventilation network problem with natural air splitting. This method tradition-ally solves each mesh equation by an approximation during each iteration. It is thus interesting from both theoretical and computational viewpoints to be able to solve for an exact solution to the mesh equation. Presented in this paper is an algorithm for computing the exact solution to the mesh equation with a variable fan pressure. The algorithm uses signum functions for air quantities to generate an alternative mesh equation in the form of a quadratic equation, which has two solutions defined by the well-known quadratic formula. The condition that the derivatives of the alternative and the original equations must be the same provides a basis for the correct choice between the two solutions.

Jan 1, 1997

By D. H. White

The term "block caving" as used in this text includes panel caving and mass caving as described by Julin and Tobie (1973). This method reportedly was conceived in 1895 when a block of ore ranging up to 200 ft (61 m) in width was undercut at the Pewabic Mine on the Menominee Range in Michigan (Bucky, 1956). Over the years this method has evolved largely as a consequence of trial and error in which operators became acutely aware of what nature would allow and what it would not. Today block caving remains somewhat of an art rather than a science where experience often dictates what needs to be done. With the plunging prices of base and specialty metals in the early 1980s caving mines sought to reduce operating and development costs in order to return to profitability. For some this became an impossible task given the design, grade and operating costs of the day and closure became the only alternative. One lesson learned from the experiences of the 80s is that survivability depends on cost competitiveness and this implies the efficient use of resources and technology. To this end applied rock mechanics serves as a useful tool. The purpose of this paper is to show how Geomechanics can be used? in block caving to facilitate sound decision making and how this equates to dollars saved. Features of mining method selection, design and operation are discussed as related to this theme.

Jan 1, 1990

The purpose of this talk is to report the answers to the-'two following questions: I. What unique services does the mining industry expect of mining and mineral processing engineers? II. What suggestions does industry offer to educators to help revamp curricula to meet the needs of a changing industry? As the result of many questionnaires filled out in person by presidents, managers, superintendents, chief engineers, metallurgists, and other responsible individuals in operations and management of large and small metal and nonmetallic mining companies in the U. S., and to some extent abroad, we now have some, specific answers to the above questions. Although answers to questionnaires continue to arrive at this writing (February 10) the volume already received is sufficient to clearly justify certain conclusions and observations. A copy of the tally of the first 117 questionnaires received accompanies this report, and I am certain that a compilation of additional questionnaire data will merely reinforce, the trends in thinking that have been' established thus far. Here are the results of the survey:

Jan 1, 1961

The evaluation of Abandoned Mined Lands can involve the investigation of very large areas of land. Often, the locations of critical areas or impending problems are unknown, and are not easily identified from the surface. Microseismic monitoring has been demonstrated to be effective in identifying potential instabilities and active movement in mines from distances of several kilometers. By placing sensors in proximity to, or in contact with, a high acoustic conductance layer close to the mined zone, large areas can be monitored for potential problems with a minimum of sensors and drillholes. As part of a U.S. Bureau of Mines contract, a prototype system was developed to identify and locate potential instability problems over wide areas of land. Once a problem area has been located, the system can be used to analyze the type of the problem, its size, relative degree of instability, and potential for damage. Continued monitoring after application of remedial measures can effectively determine the efficacy of those measures.

Jan 1, 1993

By Peter G. Zambas

In planning an underground room and pillar mine, the selection of the shaft or portal location and the orientation of the main haulage arteries is of paramount importance, particularly in view of the high dependence of the cost of truck haulage on the proper definition of these parameters. In an effort to facilitate this selection a computer program was written which, by relating the truck characteristics to the areal configuration of the property or ore-body, derives the volume-weighted total fuel and time requirements for hauling ore from every panel within the property to a specified portal or shaft location through a predetermined gridwork of haulage drifts. By varying the size and orientation of the gridwork and the location of the portal or shaft access, an infinite number of configurations can be investigated. The results of this analysis can be plotted to indicate the optimum conditions.

Jan 1, 1971

By Werner Wenzel

Whisker growth during the reduction of iron ores The phenomenon of whisker growth can be observed in a number of solid-state crystallisation reactions, which, apparently, appear in6 the first instance as though they are two independent processes. From such reactions, one can find the whisker type of crystallisation on solid bodies. These examples show, that the whisker growth is neither due to certain crystal forms with predetermined temperature and pressureranges, nor to parameters, which, ad hoc, are necessary for the crystallisation. In all cases the whisker formation seems to depend on nucleation and the availability of crystallizing material in direct environment of such a nucleus, under given parameters of a system. One can generally state, that the research of whisker growth with the aim of establishing proper physical laws, to determine the foundamentals of whisker formation and whisker growth, is at present under active study. We can conclude that, although a great number of hypothesis have been proposed; no concluding theory has yet been arrived at. In the institute for ferrous metallurgy of the technical university of Aachen, research works are undertaken to find an explination to various metallurgical phenomena through help of whisker growth which was observed under varying conditions of iron ore reduction. This was possible by using refined microscopic techniques through which the whisker growth on solid oxyde substrates is detected. This refined technique combines the latest methods of surface examination with the help of stereo-scan-electron-microscope and proper and carefull preparation of surface to be stereo-scanned.

Jan 1, 1971

By Richard W. Cannon

INTRODUCTION The authors, by means of this paper, will attempt to show the role of Induced Polarization and Resistivity surveys in the discovery of the orebodies of Gibraltar Mines Limited (N.P.L.). In this paper, we will also attempt to show the importance of conducting large enough surveys in order to properly evaluate the results obtained from these surveys. LOCATION The orebodies of Gibraltar Mines Limited (N.P.L.) are located on the western slope of Granite Mountain, central British Columbia (52°30' north, 122°16' west) (See Fig. 1). The property lies approximately 28 miles north of Williams Lake, B.C. and can be reached by way of 10 miles of newly improved road from McLeese Lake, on the Cariboo Highway. The area in and around Gibraltar Mines has a moderate topographic relief with elevations between 3,500 and 4,100 feet. {EARLY HISTORY AND GEOLOGY The present Gibraltar Mines property before amalgamation consisted of the Pollyanna property (Duval-Canex) and the Gibraltar property (original Gibraltar Mines) as well as some Coast Silver and McLeese Lake Copper claims (See Fig. 2). The Pollyanna property was first described in the 1917 B.C. Minister of Mines Report which referred to it as the "Rainbow Group". The development at that time consisted of several open-cuts on copper bearing quartz veins.

Jan 1, 1972

By Stephen C. Tadolini, Colton Cook, Cody Hildreth, Frederick Cybulski

"Broken and jointed ground is extremely hazardous and requires unique stabilization techniques to protect worker and critical entries. Bolting techniques, even the most advanced with pre-load to create roof compression, can leave large gaps of unconfined and separated roof. This roof can also be susceptible to water inflows which only exacerbate the support problem. These types of conditions existed on long term development main entry accessing several future longwall panels. The geotechnical assessment identified well-defined jointing systems that also permitted water to flow between the roof separations, which “lubricated” the roof material and minimized any frictional advantages. Chemical injection of a Polyurethane material, Minova Carbopur WS, was placed beyond the bolted horizon to move the water to the rib lines and reinforce the fractured and broken roof. The injection material permitted the effective use of bolting patterns and helped ensure long-term stability of these critical entries. The paper describes the evaluation techniques, design patterns, basis for chemical selection and application, and results and recommendations.BACKGROUNDThe injection of mine and underground civil structures using polyurethane (PUR) has been ongoing for over 50 years. The applications in mining have included gate road stabilizations, longwall set-up and tear-down entries, and simple consolidation of coal mine roofs. PURs have also been used for roof stabilization during longwall shield recoveries. Polyurethane injection was initially developed by the Bergbau-Forshung GmbH, a German coal mine research institute, in the early 1960s (Jankowski, 1972). The product became a standard stabilization method in Germany after its commercial introduction in 1971 (Knoblauch, 1994), and was successfully manufactured at the Minova Essen, Germany location for over 50 years. With the recent closing of the German underground mines, that manufacturing facility has been closed and moved to Katowice, Poland, where production continues today Injection products are also being successfully manufactured by Minova in Australia and the United States.Polyurethane injection in underground coal mines is used in difficult ground conditions in fractured immediate and main roofs. It is also common as a rock stabilization remedy to prevent longwall face caving during shield removal. As presented in the case study, polyurethane was applied to minimize the inflow of water from beneath a stream channel while providing reinforcement and consolidation of the fractured roof that had lost confinement. Polyurethane is a two-component system (Part A and Part B) that is injected into a borehole and can chemically bond to the rock, not relying on friction or mechanical interlock to provide support. The material is injected under pressure, coupled with a low viscosity and small particle size; it flows into roof fractures and separations, which are the paths of least resistance. New developments in low viscosity PUR materials allows penetration of cracks as tight as 0.002 inch (0.05 mm) wide. This also allows for the closures of extremely small cracks to minimize the inflow of water, even if the water is under pressure. Combinations of designed expansion properties and low viscosities make the materials ideal for minimizing and stopping flows of water from underground structures."

Jan 1, 2019