Search Documents

By R. K. Mehta

Existing acid mine drainage treatment techniques are not remedial In nature, i.e. though heavy metals can be removed from acid mine water, their presence in tailings and large quantities of these tailings tend to increase capital and operating cost for tailing management. This paper presents the results of a series of systematic tests which finally resulted In the development of the "ferrite" process for mine drainage of coal operations at ambient temperature. The role of pH, temperature, quantity of ferrous salt addition and degree of oxidation is investigated targeting the production of high emu spinel ferrites and effluent water complying regulatory standards with respect to Iron. manganese suspended solids and pH.

Jan 1, 1992

By W. M. Colwell

When it comes to the analysis of gold bearing ore, there are literally dozens of variables that contribute to the final "true value" of a given sample. Initial sample selection, splitting size and method, inherent nugget gold, pulverization method, and analytical method variations are but a few. However, it seems that the inherent nugget gold particle is targeted as the primary reason for intra and inter-laboratory variations in assay. The following study will show that this is not always the case. A series of tests were undertaken for the Aurora Partnership-Aurora Project to solve inter-laboratory variations in the analyses of blasthole cuttings. Initial concern was centered on the probability that free gold occurrence was resulting in erratic results for the mine's cyanide shake assays and outside laboratory fire assays. Comparison of fire assay and cyanide shake assay was sporadically consistent with previously demonstrated extraction percentage for the cyanide method. The goal was to delineate the factors that ensure consistency in analyses; implement, where needed, Good Laboratory Practices; and reestablish acceptable analytical method correlation.

Jan 1, 1993

By Stephen Liu

Tunnel excavation while mining is not often performed in North America primarily due to access constraints in both operations. Referencing European approaches for long distance tunneling, the Devil?s Slide Tunnel project has applied innovation and technology to provide the ability to overcome this unique challenge. The Devil?s Slide Tunnel requires the construction of twin bore tunnels excavated based on sequential excavation method (SEM) construction methods using New Austrian Tunneling Methods (NATM) principles. The twin tunnels are approximately 9 m (30 ft) in diameter and 1,250 m (4,100 linear ft) in length. The purpose of this project is to reroute Route 1 from around the Devil?s Slide through the San Pedro Mountains crossing from Montara, CA along the south and into Pacifica, CA in the north. The Caltrans project was awarded in December 2006 for a total of $272,366,000. The job is an A+B job, thus the estimate scheme of final lining while tunnel excavation is important to save time. A+B is a method of rewarding a contractor for completing a project as quickly as possible. By providing a cost each working day, the contract combines the cost to perform the work (A) with the cost of impact to the public (B) to provide the lowest cost to the public. Concurrent mining while lining is achieved through a series of gantries and a set of tunnel forms allowing the pass-through of the excavation equipment. The tunnel lining operation passes through several phases of work that are dependent upon the progress of the tunnel excavation process. This involves unique milestones, such as the evolution of the ventilation system, development of an enlarged cross passage to allow equipment to access each tunnel from within the tunnel and, finally, the installation of an invert prior to arch lining that limits the continuity of the final lining operation.

Jan 1, 2011

By H. -S. Yoon, C. -J. Kim, K. W. Chung

"With the final goal of ultrasonic application to ion exchange in a resin-in-pulp (RIP) system, the feasibility of an indirect ultrasonic application with a submersed ultrasonic probe was investigated first for the enhancement of ion exchange in the following resin-in-solution (RIS) system: Lewatit MonoPlus MP 600XL in an artificial solution with 106 ppm uranium. Ultrasonic radiation enhanced the ion exchange efficiency without mechanical degradation of resin. For 3.6 g/L of resin, the enhancement was 79 percent after 10 min of ion exchange and it gradually decreased to 11 percent at 60 min. In addition, a preliminary test of the mechanical stability of the resin in the RIP system showed little mechanical fracture of the resin due to ultrasound, which indicates that indirect ultrasonic application by a submersed ultrasonic probe is applicable for RIP systems. IntroductionIn uranium ore processing, the ion exchange process has been used on a commercial scale for preconcentration and purification (Gonzalez-Luque and Streat, 1984). The ion exchange process is divided into two processes: (1) a resin-in-column process with the uranium-bearing solutions passed through columns containing resins and (2) a resin-in-pulp (RIP) process with the leached ore pulp exposed to resins. The latter does not require the separation process of leach liquor and ore solids, which reduces process costs. This process, which has been developed commercially since 1955, has a certain drawback. The adsorption rate and efficiency in the RIP process are relatively low, so numerous contacts between resins and leached ore pulp are needed, which adds to the cost (Merritt, 1971). It is necessary to study methods to reduce process costs.Ultrasound can intensify mass transfer, increase the rate of chemical reactions, and change reaction pathways (Thompson and Doraiswamy, 1999; Luque de Castro and Priego-Capotem, 2007; Adewuyi, 2001; Luque-Garcia and Luque de Castro, 2003). It has great potential in chemistry and is especially considered to be a promising method for enhancing mass-transfer-limited processes, such as ion exchange. Enterzari and Tahmasbi (2009) reported the effect of ultrasound on water softening by ion exchange. Band et al. (1997) proposed a modulated ultrasound application to water desalination with ion-exchange hollow fibers. These reports revealed that ion exchange kinetics could be enhanced by the application of ultrasound. As for hydrometallurgy, Feng and Aldrich (2000) reported that the elution of an ion exchange resin was enhanced by the use of ultrasonication."

Jan 1, 2015

By David A. Summers

In May 1975 the U. S. Bureau of Mines contracted with the University of Missouri-Rolla, Rock Mechanics and Explosives Research Center to develop a Hydrominer modification to a long-wall shearer unit, wherein the rotating pick-laced drums and connecting gear drives are replaced by a water jet cutting head.1 The concept of the water jet cutting head is based on using the high localized energy of the water jets to isolate a slice of coal by cutting a slot under, at the back of, and at the top of the web. The plow blade of the head then advances into the cut and wedges the pillar over onto the conveyor (Figure 1). There were several potential advantages foreseen for the system of which perhaps the most significant were the elimination of coal dust from the working area2 and the ability, with a variation in nozzle geometry, to cut webs of greater depth with a small increase in equipment horsepower. The University initially designed the head, based on experiments carried out in the laboratory, under an earlier Bureau of mines contract. The experiments showed that it was more advantageous to work at a pressure of 10,000 psi with an estimated flow rate of 50 gpm than go to the higher pressures and lower flow rates which have been advocated elsewhere.

Jan 1, 1977

By R. J. Sawyer

The Greens Creek underground polymetallic mine restarted production in 1996 from a newly discovered high grade ore zone. Efforts to improve payable gold recovery have focused on gravity separation. The paper compares testwork and plant results for a newly installed gravity circuit.

Jan 1, 1997

By T. P. McNulty

During the last decade, many exhaustive studies have been made of process energy requirements for the production of various metals and materials. Some excellent technical papers and text books have resulted, and some of these are included in the bibliography of this paper. These studies were, of course, prompted by the economic pressures which resulted from the beginning of the "Energy Crisis" in 1973. Our intensified consciousness of the cost of energy led, then, to a greatly improved understanding of the energy consumption attributable to individual mining, processing, and refining steps. It is worth noting, however, that an awareness of the cost of energy is not new and that efforts to minimize this cost were an important part of sound mine and plant management practice throughout the earlier days of our industry. One only has to read a few accounts of mining operations around the beginning of this century to develop an appreciation for the cost of supplying wood, coal, fuel oil, or electric power to remote locations.

Jan 1, 1983

By J. Wiebmer

Some thoroughbred racehorses are great routers (distance runners), others are sprinters. Some racehorses perform best on turf, others on dirt, and some in mud. To be a winner, you have to choose the right horse for the course. It's no different when looking at an electric cable shovel, a hydraulic shovel/excavator, or a wheel loader. Each loading tool has its own zone of application. To be a winner, you have to choose the right horse for your course.

Jan 1, 1993

By N. Arbiter

Evidence for the floatability of sulphide minerals without collector is analyzed and it is shown that results obtained with ores, in contrast to those with single minerals or mineral mixtures, depend on many additional variables, some identified and others not. Because of the prevailing low levels and costs of collectors for most sulphide ores, it is unlikely that collectorless flotation will have commercial applications, so that continued research on the subject may be justifiable on theoretical but not on practical grounds.

Jan 1, 1993

By C. L. Karr

Researchers at the University of Alabama have developed a method for producing fuzzy linguistic models of mineral processing equipment directly from engineering data. These fuzzy linguistic models rely exclusively on data collected from the processing systems being modeled and do not presuppose an understanding of the physics of the system. The fuzzy linguistic models use descriptive rules and explicit membership functions that provide a precise, nonmathematical description of the processing equipment. A genetic algorithm is employed to simultaneously select rules and tune membership functions used in the fuzzy models. The result is an extremely flexible approach to modelling that is applicable in a variety of linear and nonlinear systems. The effectiveness of this approach to modelling is demonstrated using a four-input, two-output model of a grinding circuit.

Jan 1, 1996

By A. D. Davis

The Bear Butte Creek watershed, in the northern Black Hills of South Dakota, shows the effects of past mining activities in the form of dissolved metals and arsenic in stream water. Bear Butte Creek, during normal flow periods, loses all of its discharge to sinkholes that recharge the Madison Limestone aquifer. This work focused on the geochemical transport and fate of arsenic and on understanding ground-water flow conditions in the Madison aquifer through development of a three-dimensional ground-water flow model that was coupled to a geographic information system (GIS). Stream sampling and discharge measurements helped determine sinkhole losses and loading rates. Column laboratory tests provided data on arsenic adsorption and the mixing of stream water with aquifer water, which also was simulated with the geochemical models, pHREEQE and NETPATH. The models and GIS can be updated with new information and will be useful in managing the water quality of the Madison aquifer.

Jan 1, 1997

By Alessandro Boscaro, Daniele Martinelli, Cristina Gabriela Oñate Salazar, Daniele Peila, Carmine Todaro

"The wear phenomenon in TBM machines is not a simple issue, as many parameters are playing an important role on the consumption of the tools during a tunnel excavation. The action of the wear due to the contact with the soil can occur on the excavation tools, on the cutterhead, in the excavating chamber and on the screw conveyor. The test developed at the Laboratory “Tunnelling and Underground Space Center” of the Politecnico di Torino is aimed to reproduce the interaction between the tools and the excavated material, simulating the excavation conditions in terms of soil conditioning and water content. The test, which is not standardized, is studied to evaluate the wear in a global point of view. The present work starts by testing the influence of the use of chemical agents during the conditioning phase on the drop of the wear phenomenon, in terms of metal weight loss. 1. INTRODUCTION The wear phenomenon of the excavation tools used in TBM tunneling machines is playing recently a major role in the design stage of full-section tunnels in both soils and rocks. Concerning EPB excavation technology, the main issue regarding productivity is the wear of its components (Peila et al.,2012), which increases the so called dead time in the whole process. The friction generated between the components and the ground causes the consumption of the tools and other metallic components in contact with the ground, described as primary and secondary wear by Nielsen et al. (2006a). This leads to downtime, with risky and complicated maintenance operations (Peila and Schulkins, 2009), as occurred in recent tunneling works in Liguria (Italy). The study of this argument in granular soils is very delicate, as it encloses not only the properties of the excavation tools, but also the characteristics of the ground to be excavated (hardness, mineralogy composition, shape and dimension of the particles and moisture content). The penetration mechanism is based on the scraping of the ground, by mean of cutting tools, with its consequent consumption. Concerning the rocks, the excavation principle is characterized by crushing the rock mass matrix by applying high compressive stresses through cutting disks. In such a way, to avoid frequent downtimes and their consequent economic losses, it is very important to study this subject and therefore understand and forecast the durability of the components, in order to try to maximize the productivity of the machine by reducing the frequency of maintenance stoppings."

Jan 1, 2016

By Jung-Joo Kim, Jong-Uk Kim, Turab H. Jafri, Han-Kyu Yoo

"INTRODUCTION Steel sets such as H-type and lattice girders are often installed in the tunnels before the hardening of shotcrete to ensure the stability of conventional tunnels in soft ground conditions. In practice, while designing the tunnels with the help of numerical analysis, steel sets are generally considered only as temporary support elements. Only a few studies propose the direct application of composite support in the tunnel design, based on large-scale experiments and numerical analysis. In order to assess the structural performance of the composite support consisting of shotcrete and steel sets, large-scale experiments were performed on two types of arch-shaped specimens by applying the combined effects of axial forces and bending moments. Based on the experimental results, numerical analysis was performed to assess the application of composite support in tunnel design. The crown settlement, axial forces, bending moments, and load distribution in the composite support were analyzed in the light of different structural patterns. LARGE-SCALE EXPERIMENTS USING COMPOSITE SUPPORT Preparation and Procedure of the Experiments The preparation setup as well as the organized procedure of the large-scale experiments using composite support is shown in Figure 1. An appropriate geometry of the specimens was selected by considering the standard cross-section of a two-lane highway tunnel in South Korea. Under the loading conditions meant to develop the axial forces and bending moments simultaneously, arch-shaped specimens were assembled with the ends of the specimens subtending a 60° arc angle at the center of the arc circle as shown in Figure 2. The fabrication of six specimens was completed in two groups based on the dimensions of steel sets, with the first group of three specimens being reinforced by H100 (No.1, No.2, No.3) and the other three by H125 (No.4, No.5, No.6). In order to reduce the voids on the boundary of the shotcrete and steel sets, concrete was casted over the steel sets instead of using shotcrete. The specimens were designed to incorporate the uniaxial compressive strength of 21 MPa. Shear keys and steel plates were installed at the ends of the specimens, so that shear failure could be avoided at the ends and the specimens could also be protected from detachment at the fixation. Translational and rotational movements at the ends of specimens were fixed."

Jan 1, 2016

By Y. Xi

This paper offers an algorithm to determine the optimal panel size with the objective of minimizing the overall stripping cost. The approach is presented both in analytical form for regular layers of coal and overburden, and in graphical form for the cases of irregular and multiple coal seams. When the optimal panel width needs to be changed due to some circumstance, we prove in general that increasing the panel width is better than reducing it in both economics and operational efficiency.

Jan 1, 1994

By D. G. Chedgy

Environmental improvement efforts are focusing with increasing intensity on pollutants resulting from combustion. The high cost of removing these pollutants at the power station is well documented. Physical coal cleaning has always been and should remain the most economic method of reducing sulfur oxide emission from coal combustion. It is critical in the selection of preparation plant circuitry to consider capital and operating costs, as well as the level of sulfur reduction. This paper describes the technical criteria which must be used for efficient process selection and summarizes the cleaning systems available or in development.

Jan 1, 1990

By L. G. Hendrickson

Direct-reduction processes for converting iron ores to metallic iron in the solid state have been available for some time; and whenever scrap becomes expensive, there is a new wave of interest in these processes. It is well established that direct reduction, coupled with electric-furnace steelmaking, is a technically viable method for making steel and in some circumstances is economically competitive with the conventional blast-furnace--basic-oxygen-process (BOP) route to steel. This raises a number of interesting questions, several of which could be of great interest to the coal and ore mining industries. For example, what are the quality requirements of the raw materials for direct-reduction--electric-furnace steelmaking? Would they be different from the present requirements for blast-furnace--BOP steelmaking? Other questions relate to how much steel will be made by the direct-reduction route in the future. The quality questions can be discussed with a fair degree of certainty, but a prediction of the amount of steel that will be produced by the direct-reduction--electric-furnace route is beyond the scope of this paper. However, an attempt will be made to identify some of the factors that will influence whether there is a swing to direct reduction and the rate at which it may occur.

Jan 1, 1978

By James J. Scott

Three dimensional photoelastic techniques have been developed which provide information on the state of stress at any point in a model investigated. This investigation utilizes these techniques to determine the stress distributions in the pillars and the roof of a room and pillar mine model. Castolite plastic was used for the construction of the model in which a stress pattern was developed by the stress freezing process. Analysis of the stress pattern was accomplished by use of data obtained by observing points in slices from the model with a polariscope and solving data obtained by' the shear-difference method. Slices through the centerline, edge of pillar and centerline of span were investigated. Results of this work provide information on the overall stress distribution on points of stress concentration in compression, shear and tension, show relative magnitude of stress throughout the model and indicate directions of the most important stress values. A generalized roof bolt pattern is developed for room and pillar mines based on the stress distribution. A digital computer was used in the reduction of data and proved to be extremely useful for investigation of this type.

Jan 1, 1963

By E. B. Thorn

The production of portland cement requires that four basic elements -- calcium, silica, alumina and iron -- be ground to a fine powder, homogenized, and fed to the pyroprocessing unit, where it is burned to a cement clinker. The raw material must either be ground wet in a slurry form or dried and ground to a dry powder, with a fineness of approximately 85% passing the 200 M screen. According to the Portland Association's Plant Information Summary, approximately 38% of the U.S. capacity is ground wet and 62% ground dry. The following data is taken from the Portland Cement Association's 1981 Energy Survey: [Million BTU/Ton kW h/Ton Wet Process Plants 5.86 138 Long Dry Process Plants 4.97 123 Dry Preheater Plants 4.03 157 ]

Jan 1, 1984

By Joyce Lappin-Randolph

In 1977, Vertical Crater Retreat (VCR) Mining was developed at the Homestake Mine and by 1983 had become a fully integrated mining method contributing 60% to total underground production. VCR has proven successful for continuous ore blocks exceeding 55,100 tons (50,000 st) with dips greater than 60" and provides a productivity average of 39 tons (35 st) per man shift (tpms) which is 92% greater than Open Cut-and-Fill. Discontinuous ore bodies, small pods, or flat structures not amenable to bulk systems are mined with Mechanized Cut-and-Fill (MCF) and have been able to achieve a 32 tpms (29 st) average productivity. Small, low grade, remnant ore bodies were not economically viable with large scale bulk techniques and couldn't support the development required for a MCF system. As a result, Homestake began researching modified bulk mining methods to increase production rates and maintain safety, while lowering costs. A modified version of VCR with significantly diminished development was prototyped in an effort to reduce initial capital investment and expedite the production phase. This modified method is called Small Block Vertical Crater Retreat (S. B. VCR). Geology The Homestake Gold Mine is located in the northern Black Hills of South Dakota at Lead. Having been active since 1876, it now extends from the surface to the 2,440 m (8000 ft) level underground.

Jan 1, 1987

By A. G. Belova

With the federal climate change legislation in progress, there is a need for demonstration-stage technologies aimed at providing clean energy from coal. Our research aims to experimentally illustrate the feasibility of capturing CO2 on a novel sorbent system from a gaseous stream. The gas is then released resulting in a regenerated sorbent and a pressurized stream of pure CO2 to be used for storage. The proposed sorbent is a ceramic honey-comb structured monolith coated with CaO supported on a high-surface area alumina. CaO is a natural acceptor of CO2 and our design ensures the physical stability and chemical reactivity of CaO over a large number of CO2 capture/release cycles. Furthermore, the use of the monolith ensures a uniform flow through the reactor, minimizes pressure drop across the reactor, and maximizes the surface reactive area. In this paper, we will present the results from a flow-through laboratory-scale reactor that establishes the efficiency of the proposed system to capture CO2. Future applications of the reactor include integration within the new-generation coal gasification power plants, such as IGGC, as means of providing decarbonized electricity.

Jan 1, 2010