Search Documents

By John Batchelder

The Copper Canyon Cu-Au-Ag deposits include two geologically distinct hypogene ore bodies developed primarily in late Paleozoic rocks adjacent to a 38-m.y.-old potassic-altered granodiorite, whose emplacement seems to have been controlled largely by the Virgin fault, a north-striking normal fault. Widespread but subeconomic concentrations of sulfides as fracture and cavity fillings in skarn apparently preceded the final intrusion of the granodiorite. In the west ore body, metals reached ore-grade concentrations through the massive replacement of andradite by chalcopyrite, pyrrhotite, and pyrite mineral assemblages. The east ore body probably formed after the granodiorite reached its present level. Calculated 6dD values of water in equilibrium with primary and secondary biotites range from -76 to -99 per mil at temperatures indicated by d180 values from coexisting quartz and biotite. The lightest values are in secondary biotite from the east ore body. These data suggest that fluids associated with potassic alteration here were most likely composed of magmatic water mixed with some meteoric water.

Jan 1, 1976

By W. R. Peters

An experimental hole-to-hole seismic probe system has been developed for use in coal measure geology as a means of determining the structural conditions of coal seams. The source probe produces a 500-joule electric arc discharge whose seismic wavelet has a spectrum in the 200 to 2,000 Hz frequency range. Low compliance hydrophones contained in the source probe as well as in a separate seismic detector probe are matched to the frequency range of the source. Both probes are constructed with 5-72 cm diameter housings. The transducers in the probes are equipped with fluid-inflatable boots to permit operation in either wet or dry boreholes. Preliminary tests in vertical boreholes drilled 213 m apart in sedimentary rock formations show reliable operation and useful seismic propagation measurements along horizontal and oblique paths up to 232 m in length. Because the seismic wave- let has an accurately repeatable waveshape, multiple shots and signal averaging techniques can be used to enhance the signal-to-noise ratio and extend the transmission distances.

Jan 1, 1985

By E. J. Wade

My subject is gold price forecasting and monitoring as an important aspect of gold marketing. While I 'm specifically addressing gold, it is understandable that many other commodities could be readily substituted. Gold marketing must be studied as three distinct processes, and it is my intention to cover each of these processes in turn. First I?ll cover the process of gold price monitoring and forecasting in some detail. In order to select a method, or combination of methods, to be used to sell gold a determination of the future price profile is essential. The profitability of the sales effort will be determined, to a large extent, by how accurately the future price behavior of the gold market has been forecast.

Jan 1, 1985

By C. Hanson

Two modes of potential loss of oxime extractants in liquid extraction processes for the extraction of copper have been studied. In loss "by chemical degradation, two mechanisms of acid hydrolysis are possible, some reagents degrade primarily in the organic bulk phase, Others at the interface between the organic phase-- phase protects the oxime but salts added to the aqueous acid phase can promote the rate of degradation. The reagents reported on are the LIX series (Henkel Cpn), SME529 (Shell Chem.Co.) and P5100 (Acorga) Loss by organic entrainment in the aqueous phase leaving mixer-settlers has also been studied, parameters investigated including impeller/tank geometry and the phase inlet arrangements. The consequences of extractant loss by the above mechanisms...are commented upon. They include the direct economic cost, the possible environmental problems and the implications for downstream operations such, as electrowinning.

Jan 1, 1980

By Jonas Svensson

The Grangcold Pellet Process - for which patents have been applied or already granted in a number of countries - uses a hydraulic adhesive such as Portland cement, slag cements, pozzolanic cements, etc., for the production of cold bonded pellets. The idea of using a hydraulic binder for the agglomeration of iron ore fines is not new. Portland cement was proposed as an adhesive for cold bonded iron ore briquettes in patents granted more than 50 years ago (1). In a report on the briquetting of iron ore fines, published in Stahl and Eisen 1959 (2), it is stated that briquettes bonded with Portland cement are used on a small scale at on ironwork in Germany. According to the report, the briquettes showed excellent strength in the blast furnace although their general use was made impossible because they required a long hardening time, during which they are sticky, soft and difficult to store and handle. The Grangcold Pellet "recess has overcome this particular disadvantage by mixing the balls with a suitable amount of the balling concentrate before storing them. The pellets are embedded in the concentrate during storing in such a way that they are isolated from each other and thus prevented from sticking together to form clusters. Thanks to the embedding concentrate, the pellets are subjected to a more or less uniform pressure from all sides which does not deform them. Thus the mixture can he stored in a stockpile or in a silo until the pellets have hardened sufficiently. The concentrate is separated from the pellets by means of screening. The concentrate is returned to the balling operation and the pellets are either shipped to the blast furnace or stored for final hardening.

Jan 1, 1969

By Richard S. Della Valle

Sandstone and shale samples from the Morrison (Late Jurassic) and Dakota formations (Cretaceous) from northwestern New Mexico have been analyzed for the major elements Na, K, Fe and the trace elements Sc, Cr, Co, Rb, Sb, Cs, Ba, Hf, Ta, Th, iJ and the rare earth elements (REE) in whole rock and clay sized fractions by instrumental and delayed neutron activation analysis. The clay sized fraction clearly shows enrichment patterns and halo effects ; whereas, the whole rock fraction does not. Important elemental dispersion halos associated with uranium in sedimentary environments include the REE, Hf, and Sb. The distribution of these halos are due to a combination of complexation, chelation and the orignal paleoenvironments.

Jan 1, 1984

By R. Guardia, J. Hoskins, E. Claros, Y. Kamiya, R. Ramirez, J. Dalenz, P. Fernandez, E. Ilgren

Crocidolite is a well known causative agent for mesothelioma. Studies have shown that the pathogenicity of the fiber from different mines varies considerably and it has been postulated the parameter that appears most likely to account for this variation is fiber width. Epidemiological studies have shown that ‘thin’ fibers from mining areas of Western Australia and the Cape Province, in South Africa are associated with a high mesothelioma risk while exposure to ‘thick’ asbestiform amphibole fiber of the same fiber type are associated with little or no mesothelioma risk. This study is concerned with ‘thick’ Bolivian crocidolite but similar findings also probably explain the paucity of mesotheliomas in the Finnish anthophyllite, South African amosite and African Transvaal crocidolite mines. The findings from the present study suggest the incidence of mesothelioma in the three major cities of Bolivia is not significantly elevated above background even though Bolivian crocidolite has been used for the past 60 years commercially and residentially in all three cities. Although some cases of mesothelioma may have been missed due to a failure to reach hospital or a shortened natural lifespan, mesothelioma generally occurs after the age of 50, we cannot tell precisely the extent to which these were confounding. We suggest the most likely explanation for the lack of mesotheliomas despite the large populations at risk from the long and extensive residential and commercial use of crocidolite containing products, is related to an increased fiber width distribution and a concomitant reduction in the ‘Stanton fiber size’ fraction.

Jan 1, 2012

By James L. Hendrix

This paper is intended to give the reader an update on the work being done at the Mackay School of Mines about the fate of cyanide on precious metals mill tailings waste. During the last two years several tailings impoundments have been sampled and analyzed for total and free cyanides. From our sampling program we are beginning to learn valuable information concerning the fate of cyanides in precious metals mill wastes. Included in this paper is a detailed description of our sampling and analytical techniques. Also, some of the data obtained from five sites are given.

Jan 1, 1986

By A. C. Barlow

The use of deep wells for waste disposal is not a new technique. The production phase of the oil industry has been using this method to dispose of unwanted oil field brine since the 1930's The adoption of this method by other branches of industry, however, to dispose of manufactured wastes is a relatively new development, but one which is finding increased use (2). Deep well waste disposal is not an ordinary technique even though it is finding relatively wide application. In fact, just the opposite is true; it is still a rather extraordinary measure. It is not now, nor is it ever likely to be a disposal method which can be assured of success before it is tried.

Jan 1, 1964

By R. R. Klimpel

The industrial processing of ores containing precious metals such as gold is generally very mining site specific, e. g. McQuiston and Shoemaker (1985), vanZyl et. a1. (1988), Fuerstenau and Hendrix (1990), and Hausen et. a1. (1990). The variety of various mineral processing techniques employed is extensive and includes size reduction, size classification, gravity separation, roasting, cyanidation, chemical and/or bacterial leaching, ion exchange and/or solvent extraction, and froth flotation. Gold occurs in the earth's crust on the average in very low concentration estimated by various sources to be between two and five parts per billion. For a specific ore deposit to be considered as an economic source of gold, generally a concentration of near one part-per million (one gram / Mton) or more is required. From a mineralogical viewpoint, gold often occurs in its native or free form. However, it can also occur as gold compounds of telluride, antimony, and selenium contained within either sulfide minerals such as pyrite, arsenopyrite. and pyrrhotite or, to a less extent, within silicate, oxide, and carbonate minerals. In many locations, alloying of gold with silver is found. The optimal processing method for recovering gold is determined by many factors such as the mineralogy of the gold bearing minerals as well as the associated mineralogy of the gangue minerals, the type of liberation profile of the gold bearing minerals upon' size reduction, and the particle size of the gold itself. Free or native gold particles can vary in size from the extreme of large nuggets to very finely disseminated gold associated in a complex sulfide mineral matrix. Typically free gold particles of several hundred microns or larger are efficiently recovered by one or more of a number of gravity based techniques due to the large specific gravity differential of gold (19.3 to 15) versus typical gangue minerals (5 to 2.7). When gold is associated with a sulfide (usually pyrite) matrix, historically most industrial plants involving size reduction and subsequent liberation have operated in a size range of 50 to 80 percent less than 75 microns. Grinding finer than this has been normally not economical unless the ore has a high gold content in the feed ore.

Jan 1, 1998

By M. A. Girts

Wetlands can be constructed inexpensively on mined lands to treat small flows of acid mine water. Metals are removed from the water by the wetland vegetation and indigenous bacteria. Full-scale field tests initiated at over 20 mine sites during 1984 and 1985 indicate that water quality can be upgraded to meet discharge standards with relatively minor maintenance requirements. Iron concentrations of 25-85 mg/L in the influent water fall to less than 2 mg/L during flow through a small wetland. Manganese can also be removed, though somewhat less efficiently. At the discharge, pH is easily raised to 6 by flow over limestone.

Jan 1, 1986

By Hun-Joon Sohn

Chemical metathesis and electrochemical reductive conversion of chalcopyrite in the presence of cupric ions were studied in sulfuric acid solutions for temperatures up to 90°C. The process results in the displacement of iron in the chalcopyrite lattice by copper ions with rejection of ferrous ions to the aqueous phase. The rate of reaction was found to be very slow, requiring subsieve-sized particles for extensive reaction to occur. The reaction was insensitive to copper ion concentration. Stirred ball milling of chalcopyrite introduces lattice strain. The reaction rate with strained particles was markedly higher than with annealed chalcopyrite. The reaction rate was found to be diffusion-limited, showing two distinct reaction stages corresponding to the formation of CuS (covellite) followed by Cu1.8S (digenite). The experimental activation energy for the first stage was 102 J (24.4 kcal) and the second stage 123 3 (29.4 -kcal) per mole. The rate-controlling process is diffusion of lattice ions, probably iron. The enhanced rate after milling is attributed to a recrystallization process which provides new paths for diffusion along dislocations and grain boundaries.

Jan 1, 1984

By William R. Nash

Case histories of water problems in underground mine shafts and tunnels are outlined to illustrate varying degrees of sophistication in grouting techniques currently applied in such construction. The interception of water underground can be one of prior knowledge, i. e., the site investigation provides necessary data to plan a grouting program prior to construction start, or excavations may encounter "changed conditions" or unplanned water. The latter includes catastrophic inflows and emergency situations where the structural integrity of a building or concrete shaft lining are jeopardized. The presentation of this paper outlines some applications of grouting work in underground mine construction throughout the United States in a variety of geological provinces and for a variety of minerals.

Jan 1, 1984

By H. D. Dahl

In January, 1969, the Central Research Division of Continental Oil Company initiated a research program on roof control. The purpose of the research was to improve roof stability. Toward this end, it was necessary to determine which of the many geological and geometrical variables have a significant effect on roof stability. The isolation of these significant variables would allow research effort to be concentrated where it would be most effective in improving roof control. The research effort was directed toward two major objectives. One was to de-fine the geological and/or geometrical parameters that affect the severity of roof conditions in any particular area of the mine. This study was concerned with roof fall intensity. The second was to define why roof falls in Humphrey No. mine (and in northern West Virginia-south-western Pennsylvania coal mining areas) are oriented so that they occur primarily in north-south rooms or entries. This study was concerned with roof fall orientation. To provide a reference framework for further discussion, a geological description of the area is presented in Part II. In Parts III and IV, the procedures, methods, and 'results of the research applied toward the afore-mentioned major objectives are presented. Part V contains the conclusions and recommendations for-warded by this study.

Jan 1, 1971

By Steven P. Oman

Large room and pillar mines are characterized by numerous and widespread working places. Ventilation requirements are high since each panel employs men and equipment that work simultaneously in multiple headings. Also, it usually is not feasible to redirect airflow from idle to active panels as the demands of each shift vary so every panel in the mine is fully ventilated at all times. Ventilation requirements will be even higher for mines that are classified as gassy. As a result of these considerations, ventilation systems for room and pillar mines are generally designed to handle large quantities of air. But as mining progresses and the mine be- comes larger, greater demands will be placed on the ventilation system. To insure that adequate ventilation is maintained at these times, ventilation engineers must anticipate problems and plan how best to deal with them.

Jan 1, 1983

By Albert F. Duzy

Recently there have been some problems associated with hot coal in shipments from the USA to overseas markets. This paper will serve several functions. First, a brief review is presented, together with a selective bibliography. Second, a thorough discussion of coal oxidation is covered. Third, potential effects of storage are presented and, lastly, methods are suggested for the safe storage and bulk transfer of coal. The scope includes coal storage for power plants.

Jan 1, 1983

By E. L. Piper

Natural graphite has been known for many centuries, having first been reported as a distinct mineral form by Gessner in 1565. At that time, graphite was used extensively as pencil "lead" because of the ease with which it marks paper. It is a black, unctuous material found as flakes, lumps, or needles in scattered locations throughout the world. The less crystalline, or "amorphous", natural graphites are thought to have been formed from coal under conditions of high temperature and pressure. The more crystalline varieties, such as those mined in Ceylon, probably were precipitated from molten solutions or were pyrolyzed from gaseous carbon compounds. Recognition of the good thermal and electrical conductivity of graphite, together with its highly refractory nature, led to an increasing number of appli¬cations for this material. Clay and pitch bonded natural graphite has been used in crucibles, refractories, foundry facings, and other high-temperature appli¬cations. These forms constitute the most important current uses for natural graphite in the United States. Other products containing natural graphite include batteries, lubricants, pencils, brake linings, etc.

Jan 1, 1973

By Melvin W. Jackson

The study of the excavation of large spherical cavities in salt formations first became of interest in 1958 when it was recognized that a large cavity could be of value in the study of the detection or concealment of underground nuclear explosions. Previously unpublished studies are reported in this paper and other studies reviewed relating to the excavation of large cavities in salt by mining ad by solution. Special emphasis is placed on the utilization of the Tatum salt dome (about 22 miles southwest of Hattiesburg, Mississippi) for the proposed site of a large excavated cavity. The U. S. Atomic Energy Commission has recently been studying such a cavity as Project Payette, but no details have yet been published. If Project Payette is determined feasible and work funded, it would eventually involve the firing of a nuclear explosive at the center of a large cavity.

Jan 1, 1969

By Yongjun Peng, Yufan Mu

Pyrite depression in the flotation of copper ores is difficult due to the activation of Cu2+ ions on pyrite surface. In this study, the radical chain reaction involving the redox cycling of Cu(I/II) induced by sodium metabisulphite (MBS) was exploited to selectively depress the flotation of copper-activated pyrite at pH 8.0. Electrochemical measurements revealed that the presence of Cu2+ and O2 was essential to the formation of SO•− 5 through sulphite oxidation, the main entity to convert the activating species Cu(I)S on pyrite to Cu(II)-hydroxide/sulphate, causing deactivation of pyrite. The depression role ofMBS on pyrite flotation was closely associated with the type of grinding media which affected the electrochemical conditions of flotation. When forged steel was used as the grinding media, a high dosage of MBS was required to depress pyrite, but a low dosage of MBS could almost completely depressed pyrite when high chrome steel grinding media was used. This is because high chrome steel produced a stronger oxidation condition with a higher amount of Cu2+ and O2 which promoted the formation of SO•− 5

Jan 26, 2021

By Mahaboob Basha Shaik, Shakuntala Tudu, Indrajit Paul, Chandra Sekhar, Neha Gupta, Amit Kumar, Srinivas Dwarapudi, Arvind Kumar Patel

In this study, the effect of colemanite and calcined colemanite (CC) addition on the properties of iron ore pellets is studied. The pellets are prepared in a lab without and with 0.2% colemanite and varying amounts of CC from 0 to 1.0 wt%in steps of 0.2%. A reference pellet is prepared under typical plant conditions, and the properties of the reference pellet are considered as the base value for improving the cold compressive strength (CCS) while maintaining the other parameters at an acceptable limit without altering the pellet. The study also aims to provide a detailed characterization of colemanite and calcined colemanite to better understand their behaviour during firing. The lab-scale results show that the CCS of pellets made with 0.2% colemanite was reduced by 222 points (60%) as compared to the reference pellets due to crack formation during firing. The results show an improvement in the CCS of the indurated pellets with CC dosage up to 0.4%, and decreasing strength is noted thereafter. It is observed that the swelling index increases with the increase in calcined colemanite dosage. To simulate plant conditions, reference pellets and pellets with optimized CC dosage were fired in a plant furnace.

Oct 16, 2020