Search Documents

By T. Y. Yan

The various ion exchange reactions occurring during the restoration of formations contaminated with ammonia during in situ uranium leaching are reviewed. Data are presented on the restoration of a previously leached laboratory packed column using line saturated brine. Although this restoration fluid selectively and effectively removed the ammonia, 24.5 pore volumes are required to reduce the ammonia concentration from 500 to 3 ppm. The presence of NaCl in the restoration fluid is beneficial in + improving the selectivity of the system for NH removal and reducing ca++ ion consumption.

Jan 1, 1982

By K. E. Harrison

Acid rain legislation as proposed by President Bush [1], if enacted, will immediately refocus current thinking on the economic decision-making as related to coal preparation facilities. Unit operations currently ignored because of their costs, will become mandatory to coal plant designers and operators to ensure maximum energy recovery and sulfur reduction in the entire coal stream. In anticipation of this need, the U.S. Department of Energy, The Ohio Coal Development Office, EPRI and others are sponsoring research in several areas of coal preparation, and coal plant designers are beginning to consider more innovative techniques as they configure their flowsheets for plants of the future. Preparation plants then will have recleaning

Jan 1, 1990

By J. Noll, D. Yantek, B. Kendall, J. A. Organiscak

"A self-tramming remotely controlled mobile Dry Scrubber (DS) was developed by J. H. Fletcher and Co. under a contract with the National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research (NIOSH OMSHR) to reduce exposure of miners to airborne dust. NIOSH OMSHR laboratory testing showed that the DS averaged greater than 95% dust removal efficiency with the disposable filters and averaged 88% and 90%, respectively, for the optional washable filters in their pre-washed and post-washed test conditions. Although the washable filters could be reused, washing them generated personal and downstream respirable dust concentrations of 1.2 and 8.3 mg/m3, respectively, for a 10-minute washing period. The DS’s velocity pressure regulated variable frequency drive (VFD) fan maintained a relatively consistent airflow near the targeted 1.43 and 4.25 m3/s (3000 and 9000 ft3/min) airflow rates during most of the laboratory dust testing until reaching its maximum 60 Hz fan motor frequency or horsepower rating at 2610 Pa (10.5 in. w.g.) of filter differential pressure and 3.97 m3/s (8420 ft3/min) of scrubber airflow quantity. Laboratory sound level measurements of the DS also showed that the outlet side of the scrubber was noisier and the loaded filters increased sound levels as compared to clean filters at the same airflow quantities. With loaded filters the scrubber reached a 90 dB(A) sound level at 2.83 m3/s (6000 ft3/min) of scrubber airflow, indicating that miners should not be overexposed in relation to MSHA’s permissible exposure level (PEL) of 90 dB(A) at or below this airflow quantity (1). The DS’s washable filters were not used during field testing because of their lower respirable dust removal efficiency and the airborne dust generated from filter washing. Field testing the DS with the disposable filters at two underground coal mine sections showed that it can clean a portion of the section return air and provide about a 50% dust reduction at the face area downstream of the continuous miner (CM) operation. INTRODUCTION Coal mine worker overexposure to coal and quartz dust continues to be a problem at underground coal mining operations in the U.S. The U.S. Mine Safety and Health Administration (MSHA) recently changed the standard for coal mine worker respirable dust exposure from 2.0 mg/m3 average during an eight-hour shift to 1.5 mg/m3 average over the actual working shift, effective as of August 1, 2016 (1). If more than 0.1 mg/m3 quartz mass is found in the coal mine worker dust sample, the applicable respirable dust standard is further reduced to the quotient of 10 divided by the percentage of the quartz in the sample (1). Over 90% of the mechanized mining units operating in U.S. underground coal mines are continuous mining machines (2). MSHA inspector dust samples from 2009 to 2012 showed that 3.7% of continuous miner operators exceeded the 2.0 mg/m3 dust standard, while 8.8% of these dust samples exceeded the new 1.5 mg/m3 dust standard and 9.7% of these samples exceeded the reduced quartz standard (3). Additionally, roof bolter dust samples at these mechanized mining units during this same period have exceeded the 2.0 mg/m3, 1.5 mg/m3, and reduced quartz levels at 1.1%, 3.7%, and 10.6%, respectively (3)."

Jan 1, 2016

By Armando Correa de Araujo

Cationic flotation of quartz is currently utilized for the concentration of iron ores and for the cleaning of phosphate concentrates. The present work deals with depression of quartz in the presence of aluminum ions during cationic flotation. It was established-that aluminum ions depress the flotation of quartz with an amine, especially under neutral and very slightly alkaline conditions. Studies of adsorption of Al ions on the quartz surface as a function of pH correlated with depression of this mineral with an amine as collector. The presence of Al ions also enhanced the depressant action of corn starch on quartz The sodium salt of ethylenediaminotetra-acetic(EDTA) was found to be an effective complexing agent to supress the depression caused by aluminum ions.

Jan 1, 1984

"A carefully planned laboratory test program is the foundation for the successful development of a sulfide flotation process. In this paper, the development of a copper-molybdenum flotation process is described. However, the concepts discussed can be applied to most sulfide flotation systems and to many industrial minerals projects as well. Each step is examined, beginning with sample procurement and covering sample preparation, flotation test preparation grinding, scoping flotation tests for reagent scheme selection, rougher flotation parameter evaluation and cleaner circuit evaluation, through to locked-cycle testing and pilot plant design and operation. Ore variability and modeling to determine the response of various ore types to the optimum conditions established is also examined.IntroductionA carefully planned laboratory test program is essential for the successful development of any sulfide flotation process. These programs usually begin with a series of batch tests on several ore type composites to evaluate appropriate reagent schemes and delineate optimum rougher flotation conditions, such as primary grind size, flotation pulp density, flotation pulp pH and retention time. Cleaner parameters such as regrind size requirements, cleaner pH, pulp density and number of stages are then defined. Semicontinuous locked-cycle tests are performed using the parameters established in the batch tests to determine the effect of middling streams recirculation on flotation performance. The data generated and the experience gained in the locked-cycle tests may be used to design and operate a continuous pilot plant if relatively large amounts of concentrate are required for further process development, such as optimization of byproduct molybdenum production from bulk copper-molybdenum concentrate.A comprehensive ore variability program is undertaken to determine the response of various ore types to the optimum conditions established. These ore variability programs often test hundreds of samples in standardized batch rougher and cleaner tests to ensure that the orebody is well understood.This article describes the development of a copper-molybdenum flotation process, but the concepts discussed can be applied to most sulfide flotation systems and many industrial minerals projects. The block flow diagram in Fig. 1 provides an overview of the development process."

Jan 1, 2016

By A. Bruynesteyn

Results are presented from a series of tests designed to determine the beneficial effects of the microorganism Thiobacillus ferrooxidans upon the leaching of uranium from a pyritic uranium ore. Minus 1-inch (-25mm) 0.0711 percent uranium containing, pyritic ore from the Rio Algom Mine at Elliott Lake, Canada was leached with lixiviants of various Eh and pH as well as being subjected to a biologically-assisted ferric iron leach. In all cases, the biological leach gave superior extraction. At pH 1.6, the biological leach gave 100.6 percent extraction and the ferric iron leach 69.8 percent. This improvement in extraction is associated with a relatively rapid biological breakdown of the pyritic material, thus liberating uranium mineralization associated with these pyritic materials and regenerating the ferric sulphate lixiviant in situ.

Jan 1, 1981

By P. S. Sundar

A laboratory method for the simulation of in-situ leaching of uranium was developed under contract to the Interior Department's Bureau of Mines. Simulation tests using sulfuric acid, ammonium bicarbonate and sodium carbonate as reagents and hydrogen peroxide as oxidant were carried out with representative ores from Texas and Wyoming. The tests not only yielded recovery rates of uranium and permeability changes, but also qualitative inferences on the chemical and physical phenomena which occur underground. Leaching with basic solutions was found to be kinetic constrained and with acid solutions, equilibrium constrained. The rapid permeability changes observed when leach solutions were introduced, were probably caused by gas blockages in the packing. Precipitation of calcite or gypsum and the reaction of clay to leach solutions had slow and gradual effect on the packing permeabilities.

Jan 1, 1978

By J. C. Watts

Monitoring and control of conventional industrial wet grinding circuits is conceptually straightforward. However, since production objectives and operating constraints can vary widely from plant to plant, there is probably no single overall grinding circuit control strategy which is "best" in all cases; in-variably some compromise is necessary between performance desired under ideal conditions and performance achievable in practice. The recent advent of relatively low cost, reliable, high speed small computer systems is revolutionizing daily operations in increasing numbers of metallurgical processing plants. Of special power and capability is a hierarchical computer network like that currently in use at the Pinto Valley Operations of the Cities Service Company. Several satellite processors for key plant areas communicate with a master computer operating under a powerful multitasking real-time operating system. Hardware and software structure is such that downtime on one of the processors -including the master -does not have a major impact on overall system operation. Admittedly, the powerful, core efficient table driven satellite software, which handles process/computer communication, calculation of nonmeasured process variables, and basic Direct Digital Control functions, is difficult to modify. However, important high level process monitoring, report preparation, graphic display, and supervisory control functions -including economic optimization -can be implemented by project engineers at the plant site. Thus, for example, new control strategies can be quickly examined and rapidly evaluated. Such computer monitoring capability also permits use of short duration process pulse tests for approximate dynamic modeling and rapid calculation of controller tuning constants for single loop dominant systems. Following a brief back-ground discussion of the Pinto Valley Project, we present some of the more interesting results and conclusions of our work over the past year.

Jan 1, 1978

By J. R. Koehler

Yield pillar-based gate road designs oftentimes fail to provide mine operators with adequate ground control because of the unknowing misemployment of "critically" sized pillars. A "critical" pillar is one that is too large to either yield nonviolently or yield before the roof and floor sustain permanent damage, but is too small to support full abutment loads. To demonstrate the critical pillar concept, a field study of a tapering gate road was conducted by the U.S. Bureau of Mines at the Sunnyside Coal Mines, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m-wide design more closely approaches proper yield pillar dimensions. Probehole drilling of several 1 O.6-m-wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset, indicating a properly functioning yield pillar design.

Jan 1, 1995

By William F. Lawrence

Research performed by the West Virginia University Coal Research Bureau under the sponsorship of the U. S. Bureau of Mines has demonstrated that coal-ash can be converted into mineral wool insulation of a quality equal to commercial grade mineral wool. An unexpected benefit has been gained due to the discovery that the usual and costly fluxing agents employed when using conventional raw materials are not required when producing mineral wool from coal-ash. Because coal-ash sources are commonly located close to mineral wool marketing areas and because mineral wool is seldom shipped far as a result of its low weight and high volume, the use of coal-ash may offer the mineral wool producing industry profitable opportunities. Moreover, coal-ash produced from experimental limestone based air pollution control processes also yields high quality mineral wool which may aid in retarding corrosion of metals contacted by the wool. In addition, internal fluxing effects and possible sulfur oxide utilization could provide economic advantages to the use of these "modified" ashes.

Jan 1, 1969

By J. A. Organiscak

Two types of airflow splitting methods for improving longwall dust control were investigated by NIOSH's Pittsburgh Research Laboratory. These methods included a translucent mesh barrier and a staged spray barrier system to confine the shearer-generated dust to the coal extraction side of the long wall face while maintaining a cleaner split of airflow on the opposing worker walkway side of the longwall face. The translucent mesh barrier was shown to provide notable dust control effectiveness up to 60 m downstream of the shearer in both the laboratory experiments and a long wall field evaluation, provided the mesh barrier remains relatively parallel to the airflow. The staged spray barrier system showed marginal dust control effectiveness in the laboratory and subsequently was not field tested.

Jan 1, 1999

By Dan Plazak

The authors are to be congratulated for presenting a simple and practical tool for quick estimates of ground water flow rates. At the risk of detracting from the simplicity of the method, I would like to suggest a slight refinement to the equation as presented. As the authors noted, the Jacob-Lohman equation (1952) assumes confined-aquifer conditions. To use confined-aquifer equations in water-table aquifers, Jacob (1963) presented a correction to convert water-table aquifer drawdowns [ ] to equivalent confinedaquifer drawdowns [ ]:

Jan 1, 1994

By Richard Klimpel

The influence of selective chemical dispersants on the hydrocycloning of a copper ore slurry is illustrated. In the % solids and slurry feed rate ranges associated with industrial practice, desirable changes in both d50 and Sharpness Index values of classification were measured with the use of chemical as compared to tests with no chemical usage.

Jan 1, 1981

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, BRADLEY BENNETT, Patrick Zhang

This study level process design represents an economically viable method for extracting thorium dioxide and other rare earth elements from monazite ore. This paper incorporates results from the 2019 capstone project from the honors Design Internship in Green Engineering in Chemical and Biomolecular Engineering. In this activity, senior students in Chemical Engineering at the University of Tennessee (UT) focused on the development and study of a process for the recovery of thorium dioxide and P2O5 from monazite. While not mandated, the process offers rare earth oxides as attractive byproducts. The project focused on recovery of byproducts rather than the creation or addition to waste streams. Additionally, (1) the process economics relied heavily on recovery of rare earth byproducts, (2) thoriumhandling portions of the process could be effectively segregated from rare earth and phosphate handling portions of the process, and (3) thorium and uranium content of waste streams should be carefully managed and eliminated where possible.

May 29, 2020

By James Lett

The role of pre-conditioning in a caving operation has multiple benefits, ranging from assisting with improved caveability, normalising fragmentation and improving draw point hang-up frequency. At Newcrest Mining’s Cadia Operations, both the Ridgeway Deeps block cave the Cadia East Panel Cave have utilised pre-conditioning using hydraulic fracturing. Seismic response data inside and outside the pre-conditioned volume show the benefit of treating the full caving block. Cadia East has further developed pre-conditioning to mitigate developing seismic hazards associated with major structures (fault-slip events) and managing mine-wide seismic hazards in new caving operations where the potential for large damaging seismic events exists due to high stresses and hard competent rockmasses. A case study reviewing the impact of pre-conditioning to mitigate seismic hazard associated with fault slip is presented. Cadia East operation undertook a targeted hydraulic fracturing program and reduced the overall number of large events as an example of the benefits of pre-conditioning. This paper will review the application of Hydraulic Fracturing at Cadia and discuss the geotechnical and seismological parameters of seismic events that occur within and outside of pre-conditioned rockmass volumes to demonstrate the benefits that Hydraulic Fracturing bring to future caving operations.

Apr 26, 2022

By Brenton Fletcher, Yongjun Peng, Wonder Chimonyo

As a cheap, renewable and non-toxic material, starch can contribute to the sustainability of the flotation process, albeit in a minor way as one type of reagent in systems involving materials with far greater impact. But the physical and chemical versatility of starch can help address another issue, namely, that of processing complex ores with decreasing grades of valuable minerals and increasing mixtures of gangue. This paper compares the results of two lab scale flotation studies where starches (native wheat starch (NWS), dextrin and two oxidised wheat starches) were used to depress two common gangue minerals, copper-activated pyrite and carbon (graphite), over a range of dosages. The oxidised starch with the larger molecular weight structures depressed copper-activated pyrite best, and the oxidised starch with lower molecular weight structures was better at depressing graphite. In both cases, the oxidised starches allowed greater recovery of chalcopyrite, pointing to selectivity potential. The extent to which the carbonyl and carboxyl moieties of the oxidised starches contribute to depressant performance is difficult to quantify, but it should not be discounted. Importantly, the results demonstrate relatively simple modifications of native starch by oxidation can yield structures suitable for depressing gangue minerals with diverse surface properties. The challenge remaining for greater application of modified starch depressants is being able to replicate the desired structures at scale in cold-water-soluble form.

Jan 18, 2021

By Sebastian Avalos, Julian M. Ortiz, Willy Kracht

Semi-autogenous grinding mills play a critical role in the processing stage of many mining operations. They are also one of the most intensive energy consumers of the entire process. Current forecasting techniques of energy consumption base their inferences on feeding ore mineralogical features, SAG dimensions, and operational variables. Experts recognize their capabilities to provide adequate guidelines but also their lack of accuracy when real-time forecasting is desired. As an alternative, we propose the use of real-time operational variables (feed tonnage, bearing pressure, and spindle speed) to forecast the upcoming energy consumption via machine learning and deep learning techniques. Several predictive methods were studied: polynomial regression, k-nearest neighbor, support vector machine, multilayer perceptron, long short-term memory, and gated recurrent units. A step-by-step workflow on how to deal with real datasets, and how to find optimum models and final model selection is presented. In particular, recurrent neural networks achieved the best forecasting metrics in the energy consumption prediction task. The workflow has the potential of being extended to any other temporal and multivariate mineral processing datasets.

Jun 16, 2020

By Mei Long, Tawum Juvert Mbah, Jianhua Zhang, Haiwang Ye

There have been many improvements and advancements in the application of neural networks in the mining industry. In this study, two advanced deep learning neural networks called recurrent neural network (RNN) and autoregressive integrated moving average (ARIMA) were implemented in the simulation and prediction of limestone price variation. The RNN uses long shortterm memory layers (LSTM), dropout regularization, activation functions, mean square error (MSE), and the Adam optimizer to simulate the predictions. The LSTM stores previous data over time and uses it in simulating future prices based on defined parameters and algorithms. The ARIMA model is a statistical method that captures different time series based on the level, trend, and seasonality of the data. The auto ARIMA function searches for the best parameters that fit the model. Different layers and parameters are added to the model to simulate the price prediction. The performance of both network models is remarkable in terms of trend variability and factors affecting limestone price. The ARIMA model has an accuracy of 95.7% while RNN has an accuracy of 91.8%. This shows that the ARIMA model outperforms the RNN model. In addition, the time required to train the ARIMA is than that of the RNN. Predicting limestone prices may help both investors and industries in making economical and technical decisions, for example, when to invest, buy, sell, increase, and decrease production.

Jan 6, 2021

By Sah Rameshwar, T. Umadevi, K. S. SRIDHARA

In the magnetite iron ore pelletization process, oxidation of magnetite followed by sintering of the oxidized magnetite (hematite) is desirable. Optimum preheating time & temperature and roasting time & temperature is required to get the desired properties of the pellets with magnetite, hematite, and hematite–magnetite blend. In order to utilize the magnetite resources in a current induration furnace, which is designed for hematite resources, detailed pelletization studies have been carried out to optimize the firing cycle for magnetite concentrate as well as magnetite with hematite concentrate. Under optimum conditions, such as preheating temperature 1000–1150 °C, preheating time 10 min, roasting temperature 1250 °C and roasting time 7.5 min, the cold compression strength (CCS) of magnetite roasted pellets was 325 kg/p, and this was due to recrystallization of secondary hematite particles, and development of the strong slag bond between primary and secondary hematite particles. The strength of hematite concentrate pellets was 260 kg/p. From laboratory studies, it was found that without disturbing the induration furnace firing cycle, which is designed for hematite ore ~5%, magnetite concentrate can be used along with hematite concentrate in pellet blend and the strength of the pellets was 270 kg/p. As the magnetite concentrate increases in the blend beyond 5%, the preheating zone residence time should be increased or a supply of extra oxygen is required. Laboratory as well as plant investigation has shown that the addition of magnetite to the hematite mix blend improved the strength of the pellets compared to hematite pellet alone.

Oct 26, 2020

By SHANTAE LEE, ELAHEH TALEBI, Frank A. Drews, W. Pratt Rogers

Fatigue in mining operations is a serious issue and a significant contributor to incidents and accidents. While mine operators are using or introducing new technology to monitor operator fatigue, there is little work that focuses on the subjective experience of fatigue and the use of fatigue monitoring technology. To investigate this issue, eight focus groups with a total of 44 operators of heavy haulage equipment working for two mining companies in the Mountain West of the USA participated in 1-h focus groups. The topic of the focus groups was the experience of operator fatigue and issues surrounding fatigue at the workplace. The results of the content analyses suggest that operators are well aware of the signs of fatigue, and that they understand the severity of these signs as well. In addition, they are aware of the effect of fatigue on driving performance and are using a wide range of methods to manage fatigue. Finally, based on participants’ assessment, current fatigue monitoring systems lack face validity and reliability and are perceived as not being effective. The results of this study emphasize the importance of a socio-technical systems perspective in the context of miner health and safety management. Only such a comprehensive perspective can result in improvements that are sustainable.

Jun 17, 2020