Search Documents

By J. A. Barsin

Stationary air pollutant sources established prior to the New Source Performance Standard (NSPS) are not, at present, subject to federal emissions regulations. However, proposed legislation could require many existing stationary sources to reduce emissions. This paper will report upon the laboratory work undertaken to date by B&W to commercialize a limestone system for sulfur capture both in pulverized coal and cyclone coal-fired utility boilers. Updates will be provided on the US EPA/State of Ohio/Ohio Edison/B&W sponsored pulverized coal full-scale limestone injection demonstration, and on the EPRI/Baltimore Gas 8 Electric, Atlantic Electric/B&W sponsored laboratory-scale cyclone coal limestone injection investigations.

Jan 1, 1986

By J. D. Miller

The recent non-equilibrium electro-phoretic mobility measurements by laser-Doppler electrophoresis coupled with the stability and prevalence of collector colloids in soluble salt flotation systems suggest that the selective flotation of alkali halides is due to the adsorption of oppositely charged collector colloids by hetero-coagulation. Previously reported flotation results confirm this surface charge/collector colloid adsorption model. However, the nature of the inter-particle forces responsible for hetero-coagulation of such oppositely charged particles at high ionic strengths remains to be determined. In this regard, atomic force microscopy was used for inter-particle force measurements at high ionic strengths. Model systems such as polystyrene/quartz and silica/sapphire were studied to measure the particle interaction forces prevalent at high ionic strengths. Results from this study indicate that while repulsive hydration forces exist between similarly charged hydrophilic particles, attractive forces exist between oppositely charged hydrophilic particles in high ionic strength solutions. The repulsive forces between similarly charged hydrophilic surfaces at high ionic strengths (2-4 M) are described by a double exponential function with decay lengths of 0.17 and 1.4 nm depending upon the surfaces involved. On the other hand, attractive forces were observed between oppositely charged hydrophilic surfaces at high ionic strengths (2-4M) and were described by a single exponential function with decay lengths of up to 9 nm depending upon the surfaces involved.

Jan 1, 1996

By J. Kretschmann, R. Amiri

"The Sangan iron-ore mines (SIOM) in Iran are located in a remote area, near the Afghanistan border. The deposit of SIOM is containing a geological resource of 1.2 billion tons of mostly magnetite with a Fe grade ranging from 27 to 61 %. The Iranian government plans a stepwise development of SIOM in cooperation with private companies to satisfy the growing demand of the Iranian steel industry. Sustainable development (SD) is an influential ethical concept in mining all around the world. However, a successful realization of a SD is not possible without a foundation on the core values and regarding the specific circumstances of the individual mining country. This paper introduces SIOM and describes SD activities undertaken during its development. From the early stages, these activities have been realized to secure the acceptance of the stakeholders in the region. To evaluate their effects, indicators could be filtered as the ones with the highest priority for the stakeholders. Moreover Islamic values and Iranian regulations and their influences on SIOM have been analyzed. Keywords: Iran, Sustainable Mining, SIOM, Evaluation, Islamic Values INTRODUCTION Mining Industry in Iran The Islamic Republic of Iran holds 68 types of minerals, including salt, sand and gravel, gypsum, chrome, lead, zinc, copper, coal, gold, iron etc., with 37 billion tons of proven reserves and more than 57 billion tons of potential reservoirs. Iran is ranked among the 15 major mineral rich countries (1). In accordance with the statistics published by Statistical Center of Iran (SCI), there were 5.316 active mines and 84.922 employees in the whole country in 2012-13 (2) and according to the statistics published by Central Bank of Iran (CBI) in 2011 the share of this sector in the Gross Domestic Product (GDP) of the country was 1.2 per cent (3). Sangan Iron Ore Mines (SIOM) The deposit of SIOM is one of the largest iron-ore deposits in Iran, also considered to be one of the Middle East’s richest deposits, which contains a total geological resource of 1.2 billion tons of mostly magnetite with a Fe grade ranging from 27 to 61%. It is located 300 km southeast from Mashhad, the capital of Khorasan-e-Razavi Province, and 18 km northeast of Sangan town, in Khaf County, at latitude N34°24’, longitude E60°16’ in the north-eastern Khorasan-e-Razavi Province, 30 km west of the Afghanistan border (4) (Figure 1). SIOM is owned by the Iranian Mines and Mining Industries Development & Renovation Organization (IMIDRO). IMIDRO intends to develop an open pit mine complex and supporting facilities in SIOM for the production of about 20 Mtpy of iron oxide concentrate and pellets in four developing phases (5)."

Jan 1, 2016

By James R. Jones

The purpose of these opening remarks is to establish a viewpoint, which will form part of the basis for later discussion between panel members and between the panel and the audience. Important issues will be identified. These ideas in the form of questions and answers, hopefully, will provide the necessary background for the ensuing dialogue. Is There An Urgency? We do not believe there is the urgency for immediate control legislation that has been depicted by some Congressional sources, environmental groups, and certain segments of the press. Emissions of sulfur oxides in the United States have decreased 15% during the 19701s, even though the use of coal by electrical utility power plants increased nearly 80%. That trend will continue as the older plants are phased out of operation and are replaced with newer plants, which must meet the New Source Performance Standards (NSPS) requiring the use of "scrubbers" to reduce sulfur dioxide emissions by 70% or 90%. The present Clean Air Act Amendments of 1977, by allowing the logical progression of economic events- -depreciation, retirement, replacement, and growth--will produce approximately a 50 % reduction in SOX emissions by the year 2015.

Jan 1, 1984

By K. Lapakko

One responsibility of the Minnesota Department of Natural Resources is to encourage the development of mineral resources within the state. A second responsibility is to ensure that mineral development does not adversely impact other natural resources, including the water resources of the state. One approach the Division of Minerals has taken to fulfill these responsibilities is to conduct cooperative research with the mining industry. To encourage mineral development the Division has cooperated with industry on projects related to exploration, mining, and mineral processing. To examine environmental issues the Division has worked in concert with iron ore, base metal, and precious metal exploration and mining companies, as well as the Western Governors' Association, US Bureau of Mines, US Bureau of Land Management, and the US EPA for the past 20 years. These projects were conducted to evaluate methods of predicting, preventing, controlling, and treating problematic mine waste drainages, as well as mine waste revegetation. This paper I) briefly summarizes cooperative projects conducted, 2) enumerates elements which have contributed to the success of cooperative projects, and 3) describes changes implemented for future projects at the Division's new field and laboratory research facilities, as well as at existing mine and plant sites.

Jan 1, 1998

By G. Wheeler

Epithermal gold exploration in the last decade has developed useful models for exploring new ore districts in Oregon. In Eastern Oregon, disseminated gold occurs in epithermal deposits that have been pervasively silicified and brecciated. Many gold prospects staked since 1980 are in fluvial and lacustrine sandstone and conglomerate deposits. Clay alteration products and disseminated pyrite may be present. Vein filling calcite and thin to thick quartz veins are common. Late stage quartz forms pseudomorphs after calcite in many deposits. Arsenic, mercury and gold are geochemically anomolous but silver is usually not. The epithermal deposits are located in part of the Deer Butte Formation or equivalent units. Exploration criteria include the presence of Deer Butte Formation or correlative units and NW structures cut by N-S basin and range structures.

Jan 1, 1987

By Dolf Vos

The balling section of the pelletizing plant at Hoogovens IJmuiden consists of 7 balling drums. Each with an average capacity of 100 tons of green pellets per hour. The balling drums are equipped with rotating scrapers and water-spraying systems. The scrapers are installed in order to restrict the growth of the race to a certain thickness. The spraying system is used to adjust the desired value of the moisture-content of the rewetted ground ore, the pellets and the race. The desired value is the value by which the balling- process is stable, good pellets are formed and surge occurs within certain limits. In October 1980 the construction of one of the balling drums has been modified. The rotating scraper was removed and the inner wall of the drum was supplied with a rubber-lining. In 1982 a second balling drum has been rubber- lined. At the same time the Tyler vibrating screen of this balling circuit has been replaced by a roller(bed)screen. By the end of 1983 all 7 balling circuits will be equipped with rubber-lined drums in combination with roller(bed)screens. The combination of these two modifications will improve the quality and the screen analysis of the green pellets, moreover resulting in savings on energy- and maintenance costs. This paper describes the influence of a rubber- lining on the balling process and the green pellet quality by carrying out in-plant testruns in November/December 1980. The testrun results have been compared with the results of a not modified balling drum.

Jan 1, 1983

By T. J. Lutz, J. L. Carr, J. A. Yonkey, C. C. Jobes

"Since 1984, the date of the first recorded fatality involving a remote controlled continuous mining machine, 38 miners in the United States have been killed when they were struck by a continuous mining machine. Proximity detection is a valuable tool for preventing fatalities, and the use of these systems is expected to significantly improve safety. Proximity detection provides a means to prevent accidents like these. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a series of underground tests to evaluate the accuracy and repeatability of proximity detection systems under a number of conditions such as varying the orientation and height of the personal wearable device (PWD), moving the PWD close to the trailing cable, and activating the machine’s mining mode. At the 2014 SME Annual Meeting, results from tests on first-generation proximity detection systems were presented. This paper will provide results from the similar tests performed with second-generation systems. The results show that performance has improved. For example, the negative impact of PWD orientation and the trailing cable has been reduced. However, some inconsistencies remain. Notably, performance changes dramatically when mining mode is activated. INTRODUCTION Since 1984 there have been 38 fatalities involving striking and pinning of the operator and other workers by the continuous mining machine (CMM) [1]. In August 2011, the Mine Safety and Health Administration (MSHA) published a proposed regulation that would require proximity detection systems on all continuous mining machines except full-face machines [2]. Proximity detection systems are designed to stop machine motion to protect miners from striking/pinning hazards. Several MSHA-approved proximity detection systems are commercially available. MSHA estimates that of the 38 fatal striking and pinning accidents that have occurred since 1984 involving CMMs, the use of proximity detection could have been a preventative factor in at least 28 cases [1]. Furthermore, MSHA estimates that proximity detection could prevent 20% of all deaths throughout the industry [3]. NIOSH researchers have been involved in the development and testing of proximity detection technology since creating the HASARD system [4] and have recently conducted research intended to develop more advanced proximity detection technology for CMMs [5,6,7,8]. In addition, NIOSH has also conducted research investigating how the signals of a proximity detection system propagate [9,10] and have developed a novel method for determining the location of a personal wearable device (PWD) relative to the magnetic field generators [11,12]."

Jan 1, 2015

By Yoichi Shimada, Katsuyuki Nishida, Shinichi Takahashi, Yasushi Okada, Yohei Nakamichi, Kazunori Oshiro, Taichi Terui, Sigehiko Sugie

"Temporary retaining walls are ordinarily used for tunnel construction work conducted using the opencut construction method. Retaining walls in such instances are typically installed vertically. However, shoring (such as struts and king posts) is required to ensure the stability of retaining walls in cases of excavation work to depths that exceed approximately 4 m. A new design and construction method that focuses on the effectiveness of retaining walls that are installed on an incline was studied with the aim of improving construction workability by omitting shoring. The inclined braceless excavation support (IBES) method, which was developed for use with the inclined buttress method, requires no shoring, even for deep-open-cut construction work and can be applied to deep excavation work on ground with a high groundwater level. This method has been applied at six work sites in Japan in recent years. This paper introduces the IBES design and construction method and presents verification results based on the design method, a model experiment, finite element analysis, and measurements obtained during construction work.INTRODUCTIONBackgroundIn the past, temporary retaining walls used in open-cut construction work have been installed vertically, and shoring (such as struts and king posts) has typically been used to ensure the stability of these retaining walls when the excavation depth reached 3–4 m. However, shoring interferes with structures built within excavations and requires box-outs and penetration sections in the structures, as well as concrete joints that raise concerns about their impact on the watertightness and long-term durability of structures (Figure 1).Shoring also narrows the space available for conducting construction work and reduces construction work efficiency, and the installation and removal of shoring increases the construction duration and cost. As a result, there has been a demand for ways to reduce or eliminate shoring to improve the quality of structures and construction work efficiency."

Jan 1, 2016

By W. R. Bull

This paper examines water-only cyclone performance for the cleaning of fine coal, and the effects of changes in feed flow rate, feed pulp density, and vortex finder diameter. A model is presented for performance simulation which can be used to predict products obtained based on feed washability data.

Jan 1, 1987

By T. L. Barone, J. R. Patts, L. D. Patts, S. J. Janisko

"Controlling float coal dust in underground coal mines before dispersal into the general airstream can reduce the risk of mine explosions while potentially achieving a more effective and efficient use of rock dust. A prototype flooded-bed scrubber was evaluated for float coal dust control in the return of a continuous miner section. The scrubber was installed inline between the face ventilation tubing and an exhausting auxiliary fan. Airborne and deposited dust mass measurements were collected over three days at set distances from the fan exhaust to assess changes in float coal dust levels in the return due to operation of the scrubber. Mass-based measurements were collected on a per-cut basis and normalized on the basis of per ton mined by the continuous miner. The results show that average float coal dust levels measured under baseline conditions were reduced by more than 90 percent when operating the scrubber. IntroductionAirborne coal dust is a byproduct of coal production, and engineering controls exist to deal with both the respirable dust health hazard as well as the float dust explosion safety hazard. Float coal dust, smaller than 75 µm (0.003 in.) in size, can deposit throughout mine entries and propagate explosions that had been initially fueled by methane gas. The inertization of float coal dust with rock dust helps prevent a potential secondary float coal dust explosion, but a preferable course of action is to significantly reduce the hazard by removing float coal dust from the airstream before it has the opportunity to deposit on the mine’s surfaces.Since 1970, disasters due to explosions in underground coal mines have caused 201 deaths in the U.S. mining industry, including 29 deaths in a single mine explosion in 2010 (Wade, 2010; U.S. Mine Safety and Health Administration, 2015). The U.S. National Institute for Occupational Safety and Health (NIOSH) had initiated a fiveyear research project that aims to investigate methods and technologies to reduce the potential for secondary coal dust explosions by the purposeful capture and/or suppression of float coal dust prior to its deposition on the mine roof, rib and floor (NIOSH, 2013). The project aims to evaluate the efficiency of methods to reduce longwall and belt airway float dust in the general airstream as well as methods to capture it at or near the source. Prioritization is given to longwall sections given the amount of coal produced relative to continuous miner sections, but the research is open to technologies that may be adapted from one method of mining to another."

Dec 1, 2016

By Mikael Ramström, Mark Board, Clayr Alexander, Wes Johnson

"The Coeur d’Alene mining district in northern Idaho was first discovered more than 130 years ago and has been the most prolific silver producer in the United States. The Lucky Friday Mine of Hecla Mining Co. (Fig. 1) is the oldest (76 years) and deepest mine in the district, producing approximately 725 t/day (800 stpd) from narrow, vertical lead-zinc-silver veins. Cut-and-fill stoping is currently employed at depths to about 2.3 km (7,500 ft) below ground surface, making it one of the three deepest mines in the western hemisphere. The #4 Shaft, a winze collared at approximately 1.8 km (5,900 ft) below surface and extending to a depth of nearly 2.9 km (9,600 ft), was recently completed to exploit the high-grade 30 Vein, whose resource has been identified to at least 3 km (9,700 ft) in depth.As with other deep mines worldwide, a number of challenging engineering issues occur, including: high in situ rock stress, squeezing ground, seismicity, high in situ rock temperature that requires refrigeration, diesel equipment that generates diesel particulate matter (DPM) requiring high ventilation airflow rates and long travel times for worker transport to mining areas.This article describes the methods that Hecla Mining Co. has employed during the past 50 years to combat these issues, with emphasis on the current efforts to implement continuous, mechanical mining with automated or teleremote operation and to introduce electric and battery-powered equipment to minimize refrigeration and ventilation requirements for the removal of DPMs.Geology and in situ stressThe host rock mass is an extremely thick sedimentary sequence (the Belt Series) that has been tilted vertically by mountain building. The rock mass in the current section of the mine consists of weak, heavily foliated argillites and stronger, bedded silty-argillites termed siltite. The vertical veins (80° to 85° dip) are parallel to the foliation with an approximate width of around 3 m (10 ft). There are two regional, vertical faults that parallel the vein; one forming the hangingwall of the orebody and one approximately 90 m (300 ft) in the footwall. Additionally, there are several thin, rough northdipping faults that occur in the footwall of the vein which terminate on the major vertical faults.Both the argillite and vein package rock have moderate strength, with uniaxial compressive strength averaging about 100 MPa (14,700 psi with a range from about 70 to 125 MPa), and are moderately abrasive, with CERCHAR abrasivity index of 2 to 3. The major in situ stress is horizontal and oriented in a northwest direction with magnitude about 1.5 times the vertical stress. Consequently, the Lucky Friday stress magnitude at depth is analogous to significantly deeper South African gold operations."

Jan 12, 2017

The criteria used to design, operate and control flotation columns are significantly different from those used for conventional flotation machines. Therefore, a computer-aided design (CAD) package for column flotation has been developed. The simulator has been set up using guidelines developed at Virginia Tech and information published in literature during the past few years. The simulator is useful for determining the proper design and appropriate operating conditions for a column cell to fit a specific set of conditions. In addition, the simulator can be used for training in column operation and for trouble-shooting operational problems. Simulation results have been found to be in good agreement with experimental data obtained using laboratory columns.

Jan 1, 1990

By William J. Miles

For compliance with the Hazard Communication Standard and other federal and state regulations, numerous minerals, chemicals and products need to be evaluated for crystalline silica content at a threshold of 0.1 %. The polymorphs of crystalline silica that can occur in chemical and mineral products are quartz, cristobalite and tridymite. Other natural, industrial and synthetic amorphous silicas and hydrates must be distinguished from these polymorphs to prevent over-regulation in the workplace and environment. A number of industrial silica products are composed of glasses, expanded perlite, diatomite, slags, and precipitated and fumed silica products. Amorphous silica hydrates used for industrial products, include opal (hydrated silica of biogenic or inorganic origin), perlite, pumice and tuffs. In addition, crystalline and amorphous silicate minerals and chemicals, abundant in nature and industrial products, must be distinguished from the polymorphs of crystalline silica.

Jan 1, 1997

By G. A. Calboreanu

The deterioration rate of any metal or alloy is increased in a erosion-corrosion application because the passivated surface layer is removed by the solid particles contained in the pumping fluid and the material surface becomes corrosion active again. Numerous attempts were made to engineer a stainless steel with higher hardness and unaffected corrosion performance. Alloys of special interest in such an area are the duplex stainless steels particularly the CD4MCu material which has the capability of being hardened due to its ferrite-austenite microstructure. Unfortunately, the CD4MCu with higher hardness comprises different intermetallic compounds which will increase the corrosion rate. The paper is analyzing the erosion-corrosion performance of a new type CD4MCu with 32% higher hardness and superior wear performance. The corrosion performance of this new alloy is better than the corrosion performance of the common CD4MCu material which the industry could supply. The corrosion effectiveness was evaluated with the Huey test, the potentio-dynamic anodic polarization test and the weight loss test whereas the erosion resistance was established with a low stress ball-on-disk type apparatus. The Wilfley hard CD4MCu material had 39% lower weight loss and 32% smaller volume loss than the common CD4MCu alloy The hardness range of the centrifugal pump parts poured and processed with the Wilfley hard CD4MCu is 320-350 HBN versus 250-255 HBN hardness of the common CD4MCu. After approximately 18 months of experimentation and field testing it was clearly established that the life time of the Wilfley hard CD4MCu is higher than the common CD4MCu and consequently centrifugal pumps were supplied to different customers in North and South America. India and more recently Australia. Sincere thanks to all the A.R. Wlifley & Sons Inc. and Western Foundries Inc. employees who supported and help to implement this work. special thanks to George Wilfley. Dave Cobb. Bill Becker Sr. and Wayne Taylor

Jan 1, 1997

By Osvaldo Bascur, Barun Gorain, Jaco Steyn

"The last few decades have seen some remarkable advancement in information technology, but recently various digital technologies have resulted in several synergies to deliver innovation in diverse applications. The mining industry has been relatively slow in adopting these technologies compared to the other industries, but this scenario is changing fast.Challenges. Mining companies globally are going through a series of challenges such as declining ore grades with complex metallurgy, increasing depth of ore bodies, high capital and operating costs, lower productivity, shortage of technical resources, significant pressure from stake-holders to deliver, along with growing environmental and corporate social responsibility issues. Improvement in profitability would need significant improvements in operational performance.Consequently, over the last few years, there has been a major focus among some mining companies to imbibe operational excellence. This has been only possible because of the replacement of a silos-based approach by an integrated view of the organization. Such an integrated view is now possible via the evolving digital technologies. Even so, such a transformation calls for a change in culture, which, for most organizations is not trivial. Attempts in the past to integrate functions, such as through mine-to-mill initiatives in the mining industry, have demonstrated significant benefits to many operations (McKee, 2013). Still, sustaining these benefits has clearly been a challenge due to manpower turnover and lack of proper systems and structures that integrate information between business functions within an operation and between operations and the corporate level.Opportunities. The advent of digital technology has opened up opportunities to integrate interdepartmental information for a unified understanding across an entire organization. The advances in instrumentation, equipment control systems, supervisory control systems (SCADA/ Historian) and industrial networks have helped in the direction of enterprise- wide integration. The availability of real time information across an enterprise has given rise to numerous possibilities to improve organization performance. As suggested by Seshan and Gorain (2016), some of the potential opportunities are as follows:"

Jan 9, 2018

By H. J. Chen

In recent years, it has been recognized that the high horizontal stress is an important factor that contributes to a cutter roof. When the immediate roof is thinly bedded, the presence of a high horizontal stress may first cause failure on the bedding planes or weak planes, and then a cutter roof develops as the individual stratum crushes and buckles progressively layer by layer. In this study, the stress distributions in the bedding planes of the immediate roof are analyzed for an entry-pillar system in the multiple longwall panels by using the finite element method. Then the roof failure is analyzed based on the rock failure criterion and the stress distributions.

Jan 1, 1998

By R. R. Bhappu

The metallurgical processing industry is in the midst of a hydrometallurgical revolution with mining companies looking for low cost, energy efficient and environmentally friendly technologies for processing sulfide ores and concentrates. The Intec Copper Process is one of the most advanced of these technologies and has the potential to greatly change the way copper concentrates are treated in the future. Specifically, the Intec process has the ability to be built on a small scale and at mine sites while being much more economic than conventional smelting. Intec Copper has constructed a I tonne of copper per day demonstration plant in Sydney, Australia designed to verify metallurgical and operational performance. This paper will describe the process in more detail and provide preliminary results of the process based on the plant's performance. It will also compare the Intec Copper Process with a few of the competing technologies and evaluate the relative economic merits of Intec.

Jan 1, 1999

By J. M. Bray, R. R. H. Cohen, P. Kiousis, S. R. Al-Abed

"INTRODUCTION Conventional tailing storage and management practices typically utilize engineered facilities, such as ring dikes and valley impoundments. To reduce the environmental costs associated with disposing of mine wastes in tailing storage facilities (TSFs), several beneficial re-use strategies have been developed over the years. For example, thickened tailings have been used for paste backfill. It is common for tails to comprise up to 60% of the material’s total weight and it has been estimated that TSF volumes can be reduced by 60% when using this strategy, (Benzaazoua, et al. 2004). Other beneficial re-use strategies have produced unpaved temporary access roads, hot and cold asphalt, chip seals, self-compacting concrete, and golf course sand traps. This project sampled mine tailings from two different TSFs in Colorado and produced structural concrete that could potentially be used for commercial foundations, sidewalks, and paved roads. The tailings were substituted for the fine aggregates typically found in conventional concrete. The two main objectives of this study were to investigate the structural integrity of the produced concrete samples and the leaching of heavy metals from the resulting concrete. The ratio of tailings to fine aggregate (T/FA) was carefully studied to find if there was a correlation between the substitution rate and the structural integrity. The potential maximum substitution rate was also investigated for the produced concrete specimens. The potential of leaching mining impacted water (MIW) was evaluated by comparing the leachability of the raw mine tailings to the encapsulated tailings by using standard shake extraction prediction tests. MATERIAL AND METHODS Materials The four components that make up the concrete mix design for this project are: cement, coarse aggregate (gravel), fine aggregate (sand and mine tailings), and water. The type I/II ordinary Portland cement (OPC), gravel, and sand came from local cement and concrete companies in Denver, Colorado. Mine tailings were collected from two different TSFs in the Rocky Mountain Region, where Pride of the West TSF in Silverton, CO will be denoted as Site A. The primary metals of interest at the mill site are gold, silver, lead, copper, and zinc. The location of Site B will not be mentioned in this report due to confidentiality agreements with the mining company"

Jan 1, 2016

By R. Benito

This paper describes the development of a life-of-mine schedule (LOM) for one of the world's largest known sedimentary copper-cobalt districts located in the Katanga Province, Democratic Republic of Congo (DRC). A particular feature of the Tenke Fungurume LOM schedule is the considerable number of pits/phases for scheduling, each competing to provide the best ore available to a capacity-constrained process facility. This paper discusses the LOM scheduling objectives and constraints, data preprocessing steps such as ore binning, block aggregation and clustering analysis as a scheduling aid, the mine scheduling approach and results and conclusions. Mining Engineering, 2011, Vol. 63, No. 8, pp. 39-47. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011