Search Documents

By S. J. Schatzel, J. D. Addis, V. Gangrade, L. L. Chasko, C. A. Hollerich

"A ventilation study using tracer gas was conducted at a western US coal mine. The objective of the study was to evaluate the movement of longwall face air exchanges between the face and worked-out area and to document the presence or absence of face airflow pathways between these locations. The mine operator uses a bleederless longwall ventilation system with a back return and a blowing mine ventilation system. The study was conducted on an active panel and included both underground and surface monitoring sites. The study used sulfur hexafluoride (SF6) released as a slug on the longwall face and in the front of the gob inby the face. The velocity of the tracer gas movement in the gob was 0.019 m/s (3.7 fpm). The rate of movement for the overall tracer gas slug averaged about 0.0091 m/s (1.8 fpm). A separate tracer gas test initiated with the release of SF6 into the legs of the first shield showed the existence of more than one pathway of face air in the general direction from the headgate towards the tailgate corner. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of methane emitted from the face and caved gob. A more detailed characterization of longwall system air and gas movement allows a mine to better assess its ventilation design for controlling gas on the face and in the gob. INTRODUCTION During a series of stakeholder meetings, a near unanimous concern was expressed related to maintenance of effective ventilation airflow on longwall faces. There was a strong interest expressed regarding the impacts of face length and caving characteristics on the ability to maintain adequate face airflow levels. This study seeks to understand and improve a mine operator’s ability to monitor and control ventilation and methane concentrations across the longwall face by assessing airflow variations in terms of roof caving characteristics and face length. National Institute for Occupational Safety and Health (NIOSH) researchers seek to identify flow paths of ventilation airflow on longwall panels with variations in roof caving characteristics and longwall face lengths. The project research aims to develop an understanding of the role of gas dynamics in variable broken rock, interactions with ventilation airflow and methane concentrations across the longwall face area. The research also addresses continuous ventilation monitoring along the shield line to provide early detection of gas exchanges between face and gob, and thus improve a mine operator’s ability to monitor and control ventilation and methane concentrations around the face. In the context of this paper, the longwall gob refers to the pillared area behind the shields. This work reports on results from one project task to conduct field based research using a tracer gas to describe face air and gob area gas movement in a bleederless longwall ventilation system that incorporated a back return."

Jan 1, 2017

By DeVerle Harris

The enthusiasm with which individuals have participated in mineral exploration in the development of this country testifies to the fact that there was once a very real probability of making a worthwhile discovery. Over the years, the discovery and subsequent exploitation of the accessible ore deposits have made the finding of new deposits progressively more difficult. Present day mineral exploration has evolved from the lone prospector with the grubstaker behind him to a very costly and complex business, involving large sums of money and a staff of experts in the fields of exploration technology. Exploration today must be carried out on a large scale to be profitable. With the involvement of large amounts of capital, there has been a good deal of interest in methods of optimization of the allocation of the resources of a firm 'engaged in mineral exploration. As a step toward this, mathematical models have been formulated which are designed to quantify those variables of mineral exploration in such a manner that they can be integrated with all phases of the firms operations so as to optimize its profit objective or more simply, to make exploration more efficient and effective.

Jan 1, 1964

By J. Baz-Dresch

A custom-designed shotcrete system, consisting of an 8-m3 (10-yd3) transit mixer and a shotcrete spray boom carrier, is used bya 2-man crew to transport and place up to 25 m3 (32 yd3) of steel-fiber reinforced, dry, silica fume shotcrete per II-hour shift. Shotcrete is custom blended by a local supplier and delivered predampened. Mix design and quality control is performed with a computer program that develops and graphs a properly balanced mix based upon the materials sieve analyses.

Jan 1, 1991

By C. J. B. Dreyer

In terms of resources of amphibole asbestos only South Africa can be considered. There are only two asbestos producing fields, one in the Northern Cape Province producing only crocidolite and one in the Eastern Transvaal producing only amosite. The banded ironstone sequence in which amphibole asbestos occurs is discussed, and the genesis of the fibre is briefly reviewed. The properties and characteristics of amphibole asbestos are discussed and compared to those of chrysotile. Approximately 300,000 tonnes of amosite and crocidolite are produced annually. Crocidolite has a potential for a fivefold increase of production, which could be sustained beyond the year 2000. An estimate of the resources of the various producing fields in South Africa is made. Mining methods are reviewed and evaluation techniques discussed.

Jan 1, 1978

By Umay Cinarli, Ahmet Turan

High-energy consumption in primary aluminum production (from bauxite ores) makes secondary aluminum production (from metallic raw materials such as scrap and dross) very critical. Aluminum dross, as a waste, arises in pyrometallurgical processes, and it is the mixture of metallic Al, Al2O3, other metal oxides, metal halides, and some other compounds like AlN. Aluminum dross has two subgroups (white and black) with respect to its metallic aluminum content. White dross is a secondary aluminum resource because of its high metallic aluminum content, whereas black dross, having low metallic aluminum content, is generally disposed in dumping areas. In the present study, it was aimed to develop a simple technique to valorize aluminum black dross in the form of alumina-based ceramic materials through pyrometallurgical (calcination) and hydrometallurgical (leaching) operations. Moreover, thermochemical simulations were conducted by using HSC Chemistry 6.12 software to simulate calcination conditions. After leaching experiments, an alumina-based ceramic containing approximately 36.8% Al2O3, 61.4% MgAl2O4 with 1.8% Na2FeO4, which might be available to use as a spinel refractory in steel smelting furnaces, was obtained in the experiment carried out in a solution containing 10 mLH2SO4 and 40 mL distilled water (3.5 M). Moreover, the sinterability of the alumina-based ceramic was investigated at the temperatures from 1350 to 1550 °C. In the sample which was sintered at 1550 °C, a density value of 3.15 g cm−3 and a hardness value of 69.58 HV were measured.

Oct 26, 2020

By Jonathan K. Hrica, Brianna M. Eiter

The ability to identify hazards during a workplace examination is a critical skill for mineworkers to have in order to maintain a safe workplace. While research suggests that being able to successfully recognize hazards requires a complex set of competencies, it is unclear which competencies are most critical to adequately perform a workplace examination. This paper presents a hazard recognition competencies framework as an explanation of the competencies that affect mineworker hazard recognition. To better understand how the industry is selecting and preparing workplace examiners, researchers fromthe National Institute for Occupational Safety and Health (NIOSH) interviewed nine health and safety (H&S) professionals at surface stone, sand, and gravel mine sites throughout the USA. A primary purpose of these interviews was to verify the competencies included in the hazard recognition competencies framework and to understand why these competencies are critical. Finally, the results of this study are presented within the context of current NIOSH research findings related to hazard recognition.

Jul 27, 2020

By Yushuai Xian, Youjun Tao, Fangyuan Ma

This study compared particle size distribution and density distribution of crushed products for waste printed circuit boards (WPCBs) before and after heat treatment. The crushing process for heat-treated WPCBs is a selective crushing process; more metal is concentrated in the coarse particle range of 1.0–0.5 mm and high density range of 2.8–2.96 g/cm3. WPCBs were separated using the Falcon separator to recycle useful metals. The Box-Behnken module of Design-Expert was used to obtain optimal separation parameters, namely, rotational frequency of 25 Hz, recoil water pressure of 0.025 Mpa and feed speed of 34 ml/s. On this basis, the separation indexes for WPCBs with and without heat treatment were compared. Experimental results show that the recovery effect is better for heat-treatedWPCBs than for thosewithout heat treatment. Comparedwith the non-heattreatedWPCBs, the product grade of heat-treated WPCBs is 1.95% higher, and its recovery is improved by about 14%. Finally, characteristics ofWPCBs before and after heat treatment were analyzed on the basis of stress experiments and scanning electron microscopy (SEM), respectively. Results of mechanical characterization indicate that the stress experiment for non-heat-treated WPCBs has a maximumpressure load of 212 N and displacement of 20mm, but heat-treatedWPCBs only need 140 N stress and 14 mm displacement. SEM shows that copper foil and fiberglass cloth are deformed in different directions and sizes after heat treatment to form gaps, which promote liberation of copper foil and fiberglass cloth.

Sep 10, 2020

By Juan J. Monsalve, AMAN SONI, ALEX PFREUNDSCHUH, Nino Ripepi

Ground control failures are one of the main causes of accidents in the underground stone mining industry. Some of the fundamental tools for rockfall hazard identification are related to rock mass characterization and geotechnical discontinuity mapping. Recent technological advances in these methods are related to remote sensing techniques and point cloud processing software for automated discontinuity mapping. Remote sensing techniques, such as LiDAR and photogrammetry, generate multimillion point clouds with millimetric precision, capturing the structure of the rock mass. The automated point cloud processing tools offer alternative algorithm-based methods to characterize and map these discontinuities. However, their applicability is constrained by multiple factors such as site specific conditions of the rock mass and the parameters used within the mapping algorithms. This paper evaluates the performance of automated discontinuity extraction software compared with manual virtual discontinuity mapping. Sampling windows from laser-scanned sections in an underground limestone mine are defined and mapped using discontinuity set extractor (DSE). Results from the virtual discontinuity software are compared with manually extracted fractures from I-Site based on reviewing orientation, trace length, spacing, number of extracted discontinuities, and processing time. The analysis determined that the automated mapping algorithm was able to identify the same discontinuity sets that had been manually mapped. The automated mapping software mapped an excessive amount of smaller fractures, which caused the comparison of both mapping techniques to be unsuccessful in terms of trace length and spacing.

Mar 19, 2021

By S. J. Schatzel, V. Gangrade

A ventilation research study was conducted by the National Institute for Occupational Safety and Health and a cooperating trona mine in the Green River basin of Wyoming, USA. The mine operation uses the longwall mining method in trona bed 17, a commonly mined unit in the region. The longwall face length is 228 m (750 ft), and caving on the face occurred up to the back of the longwall shields. The mine is ventilated using a main blowing fan and a bleeder shaft. For this study, sulfur hexafluoride (SF6) tracer gas was released in two separate monitoring experiments. For the first experiment, tracer gas was released on the face, this test focused on airflow along the longwall face of the active panel. Face test showed the airflow patterns to be more complex than just head-to-tail flow in the main ventilation air stream on the active panel. For the second experiment, tracer gas was released 2 crosscuts inby the face on the headgate side, this test focused on gas transport in the mined-out portion of the same active panel. Gob test showed a pathway of movement through the front of the active panel gob that moved outby from the tailgate corner. The primary pathway of tracer gas movement in the active panel gob was towards the headgate and tailgate bleeders and out of a bleeder shaft. The rate of movement towards the back of the gob was measured to be 0.19 m/s (37 fpm).

By Saurabh Kundu, Shakuntala Tudu, Indrajit Paul, Chandra Sekhar, Manikanta Nallamilli, Shaik Mahaboob Basha, Neha Gupta, Srinivas Dwarapudi, Dhiraj Madhukar Kadhe

Iron ore pelletizing using compressive and shear action on wet mixture feed has been studied. The physical properties, namely, moisture content, drop strength, green compressive strength (GCS), dry compressive strength (DCS), porosity, and cold crushing strength (CCS), have been studied. Pelletizing tests were carried out on four different types of ore, namely, hematite ore, magnetite ore, goethite ore, and sinter return fines. The inference of shear forces on silica distribution index in dry pellet has been studied using optical and scanning electron microscopy. Significant improvement in physical strength was observed due to compressive and shear forces on the pellet mixture feed. However, decrease in moisture content and ball porosity has been observed. Silica distribution index improved by 1.72 times for hematite ore, 1.47 times for magnetite ore, and 1.68 times for goethite ore. It has been found that bubble cavity has been reduced which is good indicator in terms of physical properties.

Jan 29, 2022

By Hongqiang Wang, Qingliang Wang, Eming Hu, Zhiwu Lei, Fang Hu, Rui Zhang, Wei Hou

Pyrite, a mineral associated with uranium ore, is closely related to uranium leaching. In this study, Ozone micro-nano bubbles (OMNBs), as an environmentally friendly advanced oxidation technology, were used for the first time to oxidize pyrite under experimental conditions to improve the leaching rate of uranium. A laboratory-scale agitation leaching experiment of pyrite was carried out with a pH of 1.0–3.0, gas flow of 1–3 L/min, ozone generation rate of 0.55–2.22 mg/s, and pyrite concentration of 0.1–5.0 g/L for 1 h. By adding three different co-oxidant: Mn(II), Mn(IV), and Fe(III), it was found that only Mn(IV) increased the oxidation rate of pyrite by 21.7%. The results of the scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS) show that the formation of Fe(III)-O film on the surface of the ore suppresses the oxidation rate of pyrite to a certain extent. Pyrite can be rapidly oxidized up to 57.6% by OMNBs, which is beneficial to uranium leaching. This method is expected to be used for in situ acid leaching of uranium with OMNBs injected into the ground.

Jan 3, 2022

By Amila Sandaruwan Ratnayake, T. Dilmi. U. Wijewardhana, H. C. S. Subasinghe

The value addition potential of ilmenite was examined using several characterization techniques. Raw ilmenite is composed of 93.65 wt.% of FeOTiO2, 3.55 wt.% of SiO2, 1.22 wt.% of Al2O3, and the remainder being other minor oxides. Ilmenite and powdered carbonized coconut shells were mixed in the weight ratio of 4:1. A separate fraction of the same mixture was added with powdered seashells in the weight ratio of 4:1:0.5. Six fractions of each mixture were distinctly milled from 1 to 6 h in a planetary ball mill. XRD spectra (broadened and diminished reflections of ilmenite) and FTIR observations (Ti―O―Cbonding) of milled samples indicate the possible incorporation of carbon into the ilmenite structure. Any clues of an occurrence of new rutile peaks were not observed in XRD spectra of milled samples. Consequently, the carbothermic reduction has not been initiated during mechanical activation. In this case, samples powdered for 6 h in a mill were isothermally annealed for 2 h under normal airflow at temperatures of 800 °C, 1000 °C, and 1200 °C, respectively. According to the X-ray diffractograms, the annealing temperatures of 1000 °C and 1200 °C exhibited almost similar trends with rutile (R), pseudobrookite (PB) and elemental iron (F), and a very few ilmenite (I) peaks. Consequently, 6 h of milling and 1000 °C annealing were concluded as the optimum conditions for the carbothermic reduction. Moreover, this study indicated seashells as a potential rate raiser for the carbothermic reduction of ilmenite at 800 °C. Therefore, this process is applicable to upgrade ilmenite into a mixture of synthetic rutile and elemental iron.

Mar 29, 2021

By H. Askari-Nasab, B. Osei, K. Awuah-Offei

The U.S. coal mining industry consumes approximately 142 billion kWh/a of energy. The U.S. Department of Energy estimates that the industry’s annual energy consumption could be reduced by 49%. This constitutes nearly $3.7 billion of potential savings on coal production costs at 5.3¢/kWh of energy. Additionally, with climate change regulation on the horizon, any benefits from energy savings in the near future are compounded by associated reductions in CO2 emissions. Research indicates that operating conditions significantly affect energy efficiency. Modeling and simulation have been shown to be a cheap and reliable means of evaluating the effects of process interactions and operating conditions. The goal of this work was to apply stochastic process simulation to model the energy efficiency of a typical truck-and-shovel mining system and use the model to evaluate production strategies to improve energy efficiency. The research team conducted energy audits of truck-and-shovel overburden removal and used the results to develop regression models describing truck and shovel fuel consumption. The team then built a stochastic simulation model of the truck-and-shovel overburden removal operation and used it to assess a variety of improvement measures by simulation experimentation. Valid fuel consumption models for shovel loading and truck haulage have been formulated, based on the energy audit results. Valid stochastic process models of truck-and-shovel operations have been formulated to study energy efficiency. The following strategies, in decreasing order of impact, provide the most energy savings for truck-and-shovel overburden removal at the mine: (1) shorten haul roads, (2) increase shovel capacity and (3) increase shovel utilization through optimal truck matching. Additional data will be required to adequately describe operator effects on energy efficiency.

Jan 1, 2011

By Long An, Chao Wu, Yuanhui Li, Xing Sun, Shuai Xu, Changyu Jin

Stage open stope mining (SOSM) maintains the stability of excavation openings by leaving a large number of rib pillars. Affected by the strong unloading due to stage mining and the low width-to-height (w/h) ratio of the pillars remaining, largescale destabilization disasters of rib pillars or excavation openings easily occur when the distribution of ground stress or the size of rib pillars is unreasonable. In view of these problems, a physical SOSM model test was carried out based on an underground metal mine in Chifeng City, China, revealing the deformation and failure characteristics of the SOSM pillar group by overloading. The physical model test results of SOSM and room-and-pillar mining (RPM) with a weak pillar were compared, and the failure process of the SOSM pillar group showed the characteristics of rapid and severe damage. The strength difference between a weak pillar and the adjacent pillars enhanced the stress rebalancing effect and extended the failure process of the pillar group. Similar to the SOSM pillar group with a low w/h ratio, some high-strength pillars can be used to avoid large-scale destabilization disasters caused by the synchronous failure of pillars.

Mar 8, 2023

By Manoj Khandelwal, Bright Akuinor Tsidi, Newton Amegbey, Daniel Mireku‑Gyimah

One of the ambient effects of production blasting is flyrock. To effectively manage flyrock throw distance in mining, there is the necessity to successfully envisage blasting output without sacrificing the hazardous impact of flyrock which may result in fatality and operational shutdown. For flyrock throw distance prediction, velocity of detonation (VOD) and charge per bank cubic meter (CPBCM) are not usually included. This paper focuses on the use of support vector machine (SVM) regression to ascertain the impact of VOD and CPBCM on flyrock throw predictions. The machine learning models were linear support vector machine (LSVM), quadratic Gaussian support vector machine (QGSVM), fine Gaussian support vector machine (FGSVM), medium Gaussian support vector machine (MGSVM), and cubic Gaussian support vector machine (CGSVM). The outcome indicates that FGSVM was the most sensitive with a 4% improvement when VOD and CPBCM were included. As a result, the LSVM model provides a suitable AI competitive alternative tool for flyrock throw prediction in mining operations by incorporating VOD and CPBCM.

Feb 10, 2024

By Hao Zhang, Mi Zhou, Lichun Jiang, Xihong Zhang

This study investigates the roof stability of underground limestone mining in the presence of stratified joints during the excavation process. An analytical solution is derived to predict the stresses and deformation of underground tunnel structures, with the structure simplified as a double-hinge arch. The accuracy of the analytical model is validated through comparison with finite element modeling results. A parametric study is then conducted to assess the influence of different design parameters on the optimization of tunnel stability during excavation. The results indicate that the best stability of the tunnel can be achieved in engineering practices when the applied load (q) is 5 MPa and the joint inclination angle (θ) is 45°, with the roof span and thickness set at either 12 m and 8 m or 15 m and 10 m. These findings provide valuable design guidance for underground limestone mines with stratified joints.

Oct 18, 2023

By Fouad Faraj

For every blast pattern, zones of unique material types need to be classified before mining. Most material types can be summarized into different kinds of ore and waste. Blocks generated from blasthole assays are too small to be selectively mined so areas with a single material classification meeting the mine’s selective mining unit must be defined. Current industry standard practices are to manually draw ore/waste dig limits but this process is subjective and results in quantities of dilution and ore loss which can be improved upon to enhance the profitability of mining operations. Two weeks production data from a homogeneous Cu porphyry and heterogeneous Manto-type Cu deposit are used to assess the variability in the hand-drawn dig limits for 20 geologists, mining engineers, or ore control specialists and are compared with the optimal ore/waste delineation. The profit for 20 distinct hand-drawn dig limits for the homogeneous mine ranged by 3.7% from $10.5 million to $10.9 million averaging at $10.8 million. The percent range nearly doubled for the more heterogeneous mine at 5.9% from $17.9 million to $19.0 million averaging at $18.6 million. Using the optimal ore waste delineation, the profit increased to $11.0 million (1.9% increase) and $19.3 million (7.0% increase) for the homogeneous and heterogeneous deposits respectively. The natural variability, diggability requirement, and selectivity are identified as the main drivers of ore loss and dilution. Recommendations are provided for reducing the subjectivity in manual hand-drawn dig limits by integrating dig limit optimization algorithms as a tool to assist practitioners.

Feb 23, 2024

By L. Vinnett, J. Yianatos, S. Flores

"A numerical conditioning analysis for mineral recovery estimation was performed for industrial flotation plants, considering the copper (Cu), molybdenum (Mo) and iron (Fe) separability. A modified relative condition number, ?, was presented that allowed sensitivity analysis to be evaluated for the component recovery by means of an analytical formula. This closed form made it possible for the error propagation to be determined from feed, concentrate and tail grades with different orders of magnitude. The ? parameter can be evaluated using available grade data from the design criteria or historical mass balances, in which the variability is typically unknown. Reconciled data from different Cu/Mo concentrators were employed to evaluate the effect of small numerical disturbances in the grade data on the mineral recovery estimation. Higher error propagation was typically observed for Fe. The Mo minerals presented numerical problems, mainly in second cleaners and in the first cell of rougher banks. Lower condition numbers were observed for Cu due to the higher flotation rates.Mass-balance data reconciliation without redundancy was evaluated for a typical Cu/Mo flotation circuit using relative error minimization. Significant relative errors in the mineral recovery estimation were obtained with nonreconciled data in ill-conditioned problems. Negligible improvements in the mineral recovery estimation because of the data reconciliation with regard to the nonreconciled approach were obtained in well-conditioned problems. In addition, the improvements in mineral recovery estimation by using Cu, Mo and Fe in the data reconciliation were nonsignificant with respect to using only the best-conditioned component in well- and ill-conditioned problems.Despite the effort in data reconciliation and data repetition, poor performance may be obtained in ill-conditioned problems, which can deteriorate the flotation rate characterization. The error propagation has a negative impact on the mineral recovery of the first cell, which may significantly bias the flotation rate characterization of both valuable and nonvaluable elements.IntroductionMass balances have been extensively used in flotation processes to determine the mass flowrates (production) and mineral recovery (efficiency) of valuable minerals. Simple relationships for steadystate processes based on the feed, concentrate and tail grades can be obtained by taking a black-box approach. However, the calculation of concentrate flowrates from different components of the system, such as size fractions, chemical elements or minerals, does not satisfy the mass-conservation principle because of measurement errors (Smith and Ichiyen, 1973; Romagnoli and Sánchez, 2000). Mass-balance data reconciliation allows for obtaining a unique solution that satisfies the total and component mass balances, making small adjustments to the process data and taking advantage of the information redundancy (Narasimhan and Jordache, 2000). This methodology, which is based on a constrained weighted least-squares minimization, has proved to be robust when measurement errors are normally distributed, in the absence of gross errors.Commercial software has been developed to conduct massbalance data reconciliation in flotation processes, including MATBAL (Algosys, 2002), BILMAT (Algosys, 2013), JKMultibal (JKTech, 2013), BILCO (Caspeo, 2013) and HSC Chemistry (Outotec, 2013), which accomplish the reconciliation using known data accuracy in the optimization problem. The data accuracy can be obtained by sampling a stream n times in a run, known as repeats, each with independent chemical assays. Some unmeasured variables can be estimated using the measuring redundancy and sensor location. At present, grade and flow rate sensors may be incorporated in flotation to conduct real-time mass balances. However, a lack of sensor calibration and maintenance for suitable online measurements hinders the quality of the information. In"

Jan 1, 2016

By B. J. Scheiner

The Bureau of Mines, U. S. Department of the Interior, is conducting research on a dewatering technique for fine particles generated during the mineral beneficiation process that will recover a portion of the water now being lost using conventional waste disposal methods and significantly reduce the time required for land reclamation. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong stable flocs that can be dewatered rapidly on static and/or rotary screens. In field tests, phosphate clay waste has been dewatered from a nominal 2.5 percent solids to greater than 20 percent solids. In other field tests, coal-clay waste has been dewatered from a nominal 3 percent solids to greater than 55 percent solids, in addition, small-scale continuous tests have shown that bentonitic clays can be dewatered from 12 percent solids to 40 percent solids.

Jan 1, 1983

By V. D. Smar

The flotation process may be considered an interactive system consisting of many chemical, operational, and equipment variables. Changing anyone of these variables causes an overall system response change. This study examines the effects of simultaneously changing the operating variables of: (1) frother concentration and air flow rate, and (2) frother concentration and collector concentration. It is part of a comprehensive study to look at how changes in several of the major variables may be used to produce interactions which will allow the rougher flotation process to be optimized. Ultimate recovery, flotation rate, concentrate grade and froth quality, are used as the major evaluative criteria.

Jan 1, 1993