Search Documents

By O. J. R. Baena

Mining activity in the Segovia region in NE Colombia is the main source of employment in the local economy. This has created major problems of illegality and informality mining associated with a high social and environmental impact, as inefficient technologies are used and high consumption of toxic substances required in the process of gold recovery by amalgamation and cyanidation. In this work is presented mineralogical characterization of six local mills and studied beneficiation processes developed in them. With the results presented a proposed plant design that eliminates the use of mercury by replacing gravity concentration processes taking advantage of the characteristics of the treated material. Significant results were obtained regarding the recovery of precious metals and present a methodology that can be replicated in other mineral beneficiation plants that use gold amalgamation processes. This implies a significant reduction in mercury use and decreased risk of human contamination associated with this.

Feb 23, 2014

Australian underground coal mines predominately use the longwall method for coal extraction. In longwall mining at least two parallel roadways known as gateroads are mined to delineate the sides of the longwall block, a longwall installation face is then driven connecting the gateroads to enable the longwall mining equipment to be installed. Roadway development should ideally be ahead of the longwall so that the longwall equipment can be installed into the newly developed panel with minimal delay to coal production. A discrete event model of roadway development can help assess how a particular configuration may perform with high levels of variability and uncertainty in operations. One of the major delays associated with roadway development is caused by the shuttle car due to its cyclic stop-start nature. Shuttle car travelling paths and machine interactions are normally constraint by the mine?s roadway layout and mine safety issues. This paper presents simulations of shuttle car route options which can be considered at the design stage to minimize the cycle time of a shuttle car as part of a general roadway development simulation model developed using 3D Flexsim.

Feb 23, 2014

By J. G. Groppo

In 1992, 48 million tons of fly ash (not including bottom ash, boiler slag and FGD material) was produced in the United States, according to the American Coal Ash Association. Of this amount, 27.2% was utilized; although the percentage of fly ash utilized increased from 20% in 1980, there is significant potential to increase utilization. One of the primary driving forces behind increased utilization is increased disposal costs due to more stringent environmental controls and regulation. Fly ash is classified as a natural pozzolan and finds significant use as a cement additive. It has been found to increase the plasticity of the cement mixture while lowering the amount of mix water needed. In addition to improving leveling and finishing properties, fly ash improves pumpability as well as decreases the heat of hydration of the concrete mix which is particularly important in massive concrete structures such as dams where the concrete needs to cool as quickly as possible. The Loss on Ignition (LOI) of fly ash is an important quality when considering utilization. The LOI is primarily due to the presence of unburned carbon and the standard specifications for the use of fly ash as a mineral admixture in Portland cement concrete are given in ASTM C618-89a. which sets an LOI limit of 6%. However, many states have set a more stringent limit of 3%. The primary reason for the lower LOI specification is that carbon adsorbs air entraining agents which limits freeze-thaw resistance. This is particularly important in climates such as the midwestern US where multiple cycles of freezing and thawing are typical in winter.

Jan 1, 1995

By J. A. Domenico

A safe and precise mineral separation alternative to heavy liquids is being used for mineral sands exploration on large scale orebodies. The separation process, Magstream®, uses ferro-fluids and magnetic and centrifugal forces to produce precise split points over a range of specific gravities from 1.5 to 18.0 g/cc. This paper describes a commercial scale exploration program treating, roughly, 90 samples per day in Senegal (West Africa). Separation results comparing Magstream® and conventional heavy-liquid separation are presented.

Jan 1, 1994

By Brian Ulrich

The majority of individuals involved in the mining industry can appreciate and under-stand that mining is an activity that is necessary to satisfy the very basic needs of society, and to assist in accommodating our ever-changing world. As the expression goes, ?if it can?t be grown, it has to be mined.? And at this point in time, society has granted the mining industry the right to go about the business of mining, with the general anticipation that the work will be carried out without causing undue harm to the environment or populations in and around the mining operation. The term ?sustainable development? is gaining momentum as a popular concept, and indeed it has become something of a catch-all phrase, but it is important that the idea behind the term is not cast aside as a nonsense buzz word, as it simply is an indication that development (e.g. mining) can be satisfactorily carried out with an eye toward stewardship of the environment and society. On Feb. 19, 2010, a round-table discussion (Roundtable 2010) on ?Strides Toward Sustainability in Mining? was hosted by Knight Piésold and Co. (Knight Piésold) at the Red Lion Inn and Casino in Elko, NV. Knight Piésold had local representatives (Bryan Ulrich and Steve Boyce), as well as representatives from other office locations (Cynthia Parnow and Rick Damiani from Denver, CO, and Rick Frechette from Tucson, AZ) to help facilitate the discussion. The meeting played host to 30 attendees from five states. Attendees included personnel from nine mining properties and various corporate offices. The majority of participants were people who are directly involved with environmental work on a day-to-day basis. Others were project managers whose jobs involve some level of environmental focus.

Jan 1, 2010

By B. A. Ashley

In 2007, Rosebud Mining Company (RMC) opted to extend the reserve base of Tracy Lynne Mine by developing through a sandstone channel. The extension provided access to approximately 6 million additional recoverable tons (approximately 8 years of mining) which originally had been deemed inaccessible. An evaluation of the mine?s existing ventilation system, which was designed to meet the needs of the original limited reserve, concluded that two ventilation shafts would likely be required to adequately ventilate the projected workings in the expanded reserve. To assist in the evaluation, a ventilation model of the mine was developed using Ohio Automation?s ?ICAMPS MineVent? software based on field data from Tracy Lynne Mine, prior ventilation survey experience at similar RMC mines, and relevant published sources. Model results suggested that the most economical shafts would be an 8-ft diameter return and a 4-ft diameter intake. Unfortunately, issues related to property leasing and shaft site permitting caused construction delays. Therefore, the model was also used and proved to be effective in prioritizing interim ventilation upgrades which could be implemented in order to maintain coal production. Model results indicated that the best interim upgrades included rehabilitating restricted entries and damaged stoppings and replacing the main fan with a higher pressure fan. From late 2010 to mid-2012, all interim upgrades and shafts were implemented. Current models and mine experience indicate that ventilation will not be the limiting factor for mining the additional reserve.

Feb 23, 2014

By K. Lang

A test section of the upper most lift and underlying lifts of a large scale copper heap leach operation was instrumented and monitored with advanced wireline geophysics, fiber optics and resistivity electrode arrays. Elemental Capture Spectroscopy (ESC) copper measurements, resistivity measurements from an Array Induction Tool (AIT), electrical resistivity tomography (ERT) and distributed temperature sensing (DTS) with fiber optics provided integrated near real time data about the performance of the heap. During the leaching cycle, ECS provided continuous vertical measurements of copper in the upper most and underlying lifts in the test section of the heap and was used to generate a copper recovery curve. ERT inversion modeling provided high resolution 3D resistivity measurements, which were used to evaluate moisture distribution. DTS measurements of temperature were used to track the PLS front and calculate velocity. AIT induction provided highly precise bulk resistivity measurements. In-situ samplers provided PLS chemistry at multiple points. Properly integrated monitoring data can provide the heap leach operator with information that can be used to evaluate the hydrodynamics and metallurgy of the leaching process in near real time. Problems in the heap, such as pooling, channeling, longer lag and breakthrough times, excess acid consumption, increased solution in inventory, toe saturation and slope stability can be detected in near real time with the in-situ measurements evaluated.

Feb 23, 2014

By E. Taskin

Diasporic bauxite from the Mugla-Milas region was mechanically activated in a planetary mill for different activation times and the structural changes were examined by X-ray diffraction analysis (XRD), scanning electron microscopy (SEM) and specific surface area analysis (BET ? Burnauer, Emmett and Teller). Non-activated and activated bauxite samples were leached directly in alkaline (Na2O) solution at atmospheric conditions and the activation procedure led to the amorphization and structural disordering of the diasporic bauxite structure, which increased the dissolution efficiency. Effects of milling speed, liquid/bauxite ratio and leaching time on alumina extraction in direct alkaline leaching of diasporic bauxite were also studied. The alumina extraction was ~7% for non-activated bauxite and ~70% for activated (75 minute) bauxite. Key words: Diasporic bauxite, Mechanical activation, Alkaline leaching, Alumina extraction

Jan 1, 2009

By R. E. Vivas

Goldcorp is one of the largest gold producers in the world with projects in South, Central and North America. Goldcorp?s flagship operation is Peñasquito, a world-class, poly-metallic deposit that started production in 2010 which is one of the largest mines in Mexico. Since the early stages of the project, Goldcorp has used the most advanced technologies available to maximize its value. However, the implementation of optimum mine plans has been challenging to put into practice. This is due to the fact that the mine operation involves more complexity than the plans usually reflect. This challenge is an industry wide issue that presents opportunities for improvement. This technical session discusses the mine planning methodologies and procedures used to connect long, medium and short term planning strategies in order to bridge the gap and produce optimum mine plans that can be practically implemented in the field.

Feb 23, 2014

By B. Ballard

Engineers at a West Virginia coal preparation plant owned by one of the nation's largest coal producers sought a fire suppression system for the plant's MCC and cable spreading rooms. Officials considered the traditional options of water-based sprinklers, dry chemical, and clean agent systems; however, each of those options presented challenges. Sprinklers can damage electrical equipment, proper delivery of the agent and adequate coverage/protection can be an issue with dry chemical systems, and clean agent systems require room integrity. An alternative to traditional systems was discovered in the Victaulic Vortex Fire Suppression System. The first hybrid inert gas/water mist system (FM 5580), Vortex adequately addressed these concerns. The system, which deploys a high-velocity, low-pressure mixture of water and nitrogen, is not damaging to electrical equipment and extinguishes fires in open, ventilated areas. This is one of the first installations of the Vortex system in a prep plant, and is a compelling example of how new technology can overcome the challenges of traditional technologies. The paper will detail plant specs, situation, and system evaluation, selection, and configuration.

Feb 23, 2014

St. Peter sandstone is an arenaceous sheet that covers large area in North America. The interest for St. Peter sandstone has been increasing due to the upward trend for hydrofracturing and the consequent need for fracking sand. This material is possesses very unique mechanical properties. On the one hand, it is brittle as characterized by an unusually high friction angle, up to 69°, and steeply curved failure envelopes. On the other hand, it is friable, possessing extremely low, and in most cases zero cohesion. The underground mines that are working under this condition are lacking the ground control techniques for this particular mining environment. The geotechnical properties of the St. Peter sandstone were examined using uniaxial test, triaxial test, porosity test, flexural strength test. This paper aims to investigate the effect of microstructure on strength properties, utilizing microscopic studies, index test (porosity, size distribution).

Feb 23, 2014

By J. T. Winkelmann

The Mineral Park Mine is an open pit copper-molybdenum mine located in northwestern Arizona, approximately twenty miles northwest of Kingman, Arizona. The concentrating facility has been regarded, with the expansion in 2011, as a plant capable of treating fifty thousand short tons of feed per day for the mixture of supergene and hypogene ores available. The grinding circuit consists of two 32? x 14? SAG mills and four 20? x 28? ball mills. As ores became harder with greater depth in the adjacent pit areas, however, the SAG mills became severely throughput limited. The traditional treatment for similar properties is the installation of a recycle pebble crushing circuit. Because the cost of such an installation is quite elevated, and preliminary testing and research was inconclusive regarding the predicted throughput increases, management and technical personnel set out to find another solution to the problem. The result entailed a redesign of SAG lifters/liners and a nearly unique circuit change which was, at best, a difficult step that defied current grinding logic. This paper describes these changes, events leading up to them, and the results.

Feb 23, 2014

By E. J. Owen, S. Cherotich, V. T. McLemore

Breccia pipes are vertical pipe-like columns of rocks that provide conduits for fluid flow and open spaces for mineral precipitation, hence are focus areas for exploration. In the Gallinas Mountains, Lincoln County, New Mexico, there is recorded production of Cu, Pb, Ag, F, Fe, REE (as bastnäsite), and Au from 1902 to 1980, but no production reported from the breccia pipes. Previous studies described the occurrence of REE in breccia pipes, but their transportation and deposition controls are still unclear. The aim of this research is to characterize the magmatic-hydrothermal breccia pipes in order to understand the geochemical and physical conditions of deposition of REE and gold in the breccia pipes found in the Gallinas Mountains. There are more than 20 exposed breccia pipes that form a NE-trending belt about 3–5 kilometers, mostly gray-brown and consist of angular- to sub-rounded rock fragments, some host high concentrations of REE (80,500 ppm total REE) and Au (175 ppb). Preliminary studies suggest they are magmatic and intruded into the host rock and, subsequently, hydrothermal fluids precipitated F-REE and Au along the edges of some breccia pipes. More studies are underway to test this hypothesis.

Feb 1, 2023

By Vic Miller

Highly variable milling properties within a geologically complex porphyry copper deposit owned by Kennecott Corporation in Nevada made it necessary to estimate the copper recovery and concentrate grade in areas where actual test data was lacking. The estimation was made by first determining the relationships between the desired metallurgical properties and the ore's petrology (i.e. copper mineral type, rock type and copper grade). This relationship was then combined with the already estimated rock type, mineral type and copper grade data in the mineral block model to predict the milling properties.

Jan 1, 1983

By Earle Faig

Along with other transportation modes, the barge industry will be greatly effected by trends in domestic coal production. Traditionally, coal has been one of the major commodities moved by barge. Now, because of events in the international energy market, coal is finally getting the recognition it deserves as a major component of the country's energy program. Perhaps even more significantly, a series of events have caused other countries to turn to the United States as a source of coal. Although the outlook for coal demand is optimistic, it will be greatly influenced by the ability of the transportation sector to handle the additional traffic. Because of our long experience in moving large quantifies of coal, the barging industry is in an excellent position to capitalize on coal's increased popularity. A brief description of the barging industry should facilitate the discussion of coal as it relates to the barging industry. Barge companies operate on a 40.23-Mm (25 000 mile) river system which includes the East and West Coasts and the Mississippi River System. Included in the Mississippi River System are the Allegheny, Monongahela, Kanawha, Ohio, Illinois, Missouri, Tennessee, Cumberland, Arkansas, Warrior - Tombigbee and Mobile Rivers as well as some smaller tributaries. The Gulf Intracoastal Waterway, which stretches along the Gulf Coast from Brownsville, Texas to Apalachicola, Florida, is also considered part of the inland waterway system.

Jan 1, 1981

By Drew A. Meyer

Magnetic metals are the granddaddy of products which may be recovered from municipal waste. Aside from hand-picking of newsprint and corrugated boxes, magnetic metals are usually the first items a resource recovery facility considers extracting from the solid waste stream. Magnetic metals from incinerator residues and from municipally mandated source segregation programs were first used in significant quantities by the Copper Industry. The ability of the Copper Industry to consume metals from the municipal solid waste stream raised everyone's hopes that there would be more markets for municipal scrap when more of it became available. Somehow something has gone wrong. It is widely acclaimed that scrap is an environmentally sound and economical source of iron. It is greatly in demand for Its contained energy. The prices that the steel industry has been willing to pay for the scrap during the past year are all the proof anyone should need that scrap Is desirable and sought after. But the very fact that I'm speaking today on the markets for magnetic metals recovered from municipal waste indicates that something Is wrong. Clearly the problem is not that we do not need the scrap. The problem is we have not produced the kind of scrap that consumers are willing to buy - either through ignorance of what the consumers wanted or through a conviction that ferrous scrap is so obviously a good thing somebody will surely want it no matter what. Dr. Harvey Alter of the National Center for Resource Recovery has said "You can't sell garbage". In a sense that is only partly true. It really should be "You can't sell garbage for very long". The Steel Companies, in an effort to prove that steel is an environmentally desirable packaging medium, have bought some scrap that can only be described as garbage. They are to be commended for doing so. The fault lies not with the Steel Company for taking and paying for "garbage" but with the producer of that poorly prepared scrap. Far every instance where the steel industry has purchased the often undesirable product from resource recovery facility there are several magnetic installations sitting Idle because someone forgot the most essential part of producing the magnetic product - selling it to someone.

Jan 1, 1975

By Piyush Rai, Suresh Kumar Sharma, Punit Paurush

The present study has been conducted in surface limestone mine to select the controllable blasting design parameters affecting the peak particle velocity (PPV) for assessment of ground vibration. The study aims at using two prominent statistical tools, namely, principal component analysis (PCA) and stepwise selection and elimination (SSE) techniques for identifying the key controllable parameters affecting the PPV. For determining the correlation coefficient between blasting design parameters and PPV from 44 field scale trial blasts, multi-variate linear regression (MLR) technique was done. It was found that the PCA and SSE eliminated a huge number of controllable parameters to identify the most important parameters, affecting the PPV. The PCA eliminated 6 number of parameters while SSE eliminated 5 number of parameters, and the coefficients of determination (R2) obtained were 0.616 and 0.584 for PCA and SSE respectively. The predictor equations were evolved, and these equations were used to validate the PPV results for another set of 21 field scale trial blasts. The predictor equations have been found to be fairly accurate in predicting the PPV values. Further, the PCA technique provides very near prediction of PPV with high degree of correlation in comparison to SSE technique. The paper highlights the role of state-of-art statistical tools in selecting the blasting design parameters affecting the PPV in field-scale blasting.

Mar 1, 2021

By Yi Yang, CHENGLONG XU, HAORAN LI, YALI FENG, JINRONG JU

This study presents a method for recovering valuable metals and synthesizing anhydrite from steel slag using sulfuric acid leaching and solvent extraction. The process achieved high leaching efficiencies for V, Ti, Fe, and Mg, and produced anhydrite with 93.09% purity. The leachate was further processed to separate and recover V, Ti, Fe, and Mg using selective stripping and precipitation methods, offering a sustainable approach to steel slag utilization.

Jan 22, 2022

By Ashis Bhattacherjee, Bijay Mihir Kunar

A literature review on quantitative analysis of mine safety studies revealed that investigators use a wide range of statistical techniques for the analysis of mine injury data. Researchers have addressed the various issues of accident causation and prevention through analysis of mine injury data collected from mines. These studies are generally based on historical accident/injury data without considering the injured person/population at risk. In this paper, a public health approach, based on scientific methods of epidemiology, is presented to address mine safety issues. Epidemiology is the scientific study of disease and injury patterns among populations in time and space. Originally, epidemiology was concerned with epidemics of communicable diseases. Then it was extended to non-communicable diseases. Safety researchers found that epidemiologic methods are the best tools for injury research, because the occurrences of injury and the occurrences of disease are quite similar. As a result, some researchers started applying this concept to injury research. This paper presents some of the techniques used in epidemiologic studies and illustrates the application of a case-control study design to evaluate the role of some risk factors associated with injuries in underground coal mines. In this study, the injured persons were identified and, simultaneously, interviews were conducted to find the significant risk factors responsible for occupational injuries in coal mines.

Jan 1, 2011

By CHENGLONG XU, HAORAN LI, YALI FENG, JINRONG JU, Shunliang Liu

In order to realize the resource utilization of spent hydrodesulfurization catalyst, a solvent extraction-oxalic acid precipitation process is studied in this paper for efficiently recovering vanadium, nickel, and aluminum from the acid leaching solution of spent hydrodesulfurization catalyst. The process conditions for extracting vanadium with Cyanex 272 and precipitating nickel using oxalic acid as a precipitation agent were explored in detail. The results show that vanadium (IV) in the sulfuric acid medium containing nickel and aluminum was efficiently and selectively extracted by Cyanex 272. After three-stage countercurrent extraction, the extraction efficiency of vanadium was 99.76%, and the co-extraction efficiencies of nickel and aluminum were only 2.47% and 1.87%, respectively. Thermodynamic calculation shows that the extraction of vanadium (IV) from the sulfuric acid medium with Cyanex 272 is an endothermic reaction. The innovative method of oxalic acid precipitation was used to recover nickel from the raffinate, achieving selective extraction of nickel from the solution containing a high concentration of aluminum. The precipitation efficiency of nickel was 98.58%, while that of aluminum was only 0.75% under optimal conditions. The proposed flowsheet for the separation of vanadium, nickel, and aluminum from acid leaching solution may provide a new idea for the comprehensive recovery of valuable metals from spent hydrodesulfurization catalyst.

Nov 30, 2022