Search Documents

By C. I. Basilio

Pearson's hard and soft acid and base (HSAB) principle may be applied to flotation systems. The HSAB principle states that hard acids prefer to bond with hard bases and soft acids prefer to bond with soft bases. By determining the Drago E and C parameters for the different components of a flotation system, the HSAB principle could be used to explain the selectivity of some collectors such as thionocarbamates against some minerals. Determination of these parameters is done by utilizing Drago's theory and flow micro-calorimetry.

Jan 1, 1991

By J. L. Carr

On average, one to two fatalities occur every year when a miner is struck or pinned by a continuous mining machine (CMM). Proximity detection systems offer an effective means to prevent these types of injuries and fatalities by sensing the presence of a miner and automatically disabling machine motion. The Mine Safety and Health Administration (MSHA) is expected to finalize a regulation that would require the use of proximity detection systems on all CMMs. Approximately one-fourth of all CMMs in use in the United States are already equipped with such a system. The use of these systems will save lives, not only by automatically preventing accidents but also by acting as a tool for educating miners and reinforcing safe work practices. Researchers at the Office of Mine Safety and Health Research (OMSHR) have conducted a series of field evaluations to quantify the performance of these systems in an underground coal environment. These field evaluations measured the distance at which the warning and stop zones were activated. The technology provided consistent activation of the warning and stop zones under many of the conditions tested. However, some performance inconsistencies were observed which present opportunities to improve the reliability of proximity detection system technology. Some of the notable variables that caused significant changes in performance and should be considered in the design, implementation, and use of proximity detection systems include interaction with the trailing cable, performance changes during tramming, and orientation of the miner-worn component.

Feb 23, 2014

By Véronique Falmagne, Chantale Doucet, Thomas Côté

Production began in the Deep 1 zone of Goldex mine in 2017 at a depth of 1,200 m. Stope dimensions are 50 m high by 22 m wide (along strike) and the panel thickness varies between 22 to 35 m. The Deep 1 orebody is 350 m high by 400 m along strike and 200 m from hanging wall to footwall. The mining method is longhole with paste backfill with a three dimensional primary/secondary sequence advancing upwards in a typical chevron approach and retreating from hanging wall to footwall in a V-shape from a central panel. Mining at a depth of 1,200 m in massive granodiorite brings challenges related to seismicity.

Apr 26, 2022

By Adam Bedell, Paul Derby, Brad Crenshaw

Modified contact grouting was introduced almost 15 years ago as a methodology combining traditional contact grouting and consolidation grouting to address groundwater infiltration into hard rock tunnels that utilize cast-in-place concrete as permanent tunnel support. This process has been used on additional tunnels (since initially presented) as a measure to mitigate both groundwater infiltration and exfiltration. During this time, self-sealing grouts have been developed and have been added to the process to further reduce groundwater infiltration that occurs through cracks and discontinuities within the concrete liner itself. This modification is presented and additional results from the grouting process are discussed.

Jun 13, 2021

By R. Asamoah, P. Forson, W. Skinner, M. Zanin

Despite the seeming benefits decoupling pyrite and arsenopyrite minerals present in practice, little success has been achieved. The present study presents possible process routes for attaining selective flotation broadly capitalizing on differential oxidation between these minerals, and the use of a chelating collectors. The best performance was achieved with dithionocarbamate application following copper activation, yielding 81.4% arsenopyrite and 37% pyrite recovery. Preaeration followed by staged addition of xanthate produced 76% arsenopyrite and 31% pyrite recovery while reverse flotation of pyrite after H2O2 addition gave rise to rejection of 66% pyrite accompanied with 24% arsenopyrite.

Mar 2, 2022

By F. Rudloff, C. Karageorgos, J. Moyo, I. Boadi, M. Struble, B. Lumsden

Over it’s more than 100-year history, the Kennecott operation has often been at the forefront of innovation; driven by the demands of the lower grade ore-body and the higher costs of operating in the US where wages are generally higher and regulation more restrictive. One way of reducing operating costs in c/lb is to increase the lbs produced at minimal cost. Despite the relatively coarse grind at Kennecott - about 30% >150μm, approximately 20% of the Cu lost to tail is liberated chalcopyrite in the <20μm fraction, and about 30%-40% in the <37μm fraction. In 2020 Kennecott undertook a detailed plant scale test of the magnetic aggregation technology to increase copper recovery by reducing fine copper losses. A paired statistical plant test of magnetic conditioning on one rougher line showed a 1.12% increase in Cu recovery to 97% statistical confidence. The next challenge, unforeseen at the start of the project, was the fabrication and transportation to site of the equipment for the three remaining rougher rows, during the severe supply-chain constraints of the Covid pandemic in 2021. This resulted in delays and unforeseen costs as world-wide transportation became chaotic, particularly transportation via west coast USA. Nevertheless, the project was completed and commissioned, with only minor delays and cost increases, due to a flexible approach to overcoming the hurdles encountered.

Feb 1, 2023

By M. Stuart

The copper-silver-mercury orebody of Gortdrum Mines (Ireland) Limited is located 3 miles north of the town of Tipperary in the Republic of Ireland. A drilling programme from 1964 to 1966 delineated an ore¬body of 4.19 million tons of copper ore assaying 1.19% Cu and 0.75 ozs per ton Ag, which could be mined from an open pit. Testwork having shown that the ore was amenable to conventional flotation techniques, it was decided to build a concentrator of 500,000 tons ore per year capacity. Stripping of the open pit commenced in 1966 and in the autumn of 1967 the concentrator started up. The first shipments of concentrates were made to the smelter in Europe in late 1967. In the spring of the following year, word was received from the smelter that these early shipments contained between 1% and 2% Hg, and that the smelter could not accept further shipments of this quality.

Jan 1, 1973

By Fahimeh Dehghani, Louis Ackah, Tathagata Ghosh, Justin Godbold, Jia Liu, Meisam Peiravi, Manoj Mohanty, Azam Baharlouei

Primary economical deposits of rare-earth elements (REEs) are exhausting all over the world, and it has become necessary to find new sources and methods for their extraction. In addition, increasing the application of REEs in modern technological society has increased its demand globally. One of the important movements to compensate for the future shortages of critical metals is the recovery of REEs from recyclable materials. This paper presents a review of the classification and extraction methods, as well as general applications of REEs with emphasis on secondary sources such as coal and coal byproducts, iron ore tailings, apatite, and phosphate byproducts. An overview of the current state of knowledge on the various methods of REE beneficiation and extraction is covered. These methods include physical separation, as well as hydrometallurgical and bio-hydrometallurgical techniques. The application of these REE extraction techniques for enhanced recovery has been driven primarily by the unique industrial application of these important elements. This paper further explores the existing and potential environmental challenges associated with REE extraction. The authors have presented a wide array of literature, in-depth discussion of the subject, and a succinct summary of processes and relevant case studies.

Sep 23, 2020

By K. Muralidharan, P. R. Rao, M. Momayez, K. A. Runge

The evolution of trapped geothermal heat in hot underground mine along with emission of toxic gases and dust during mine activity makes the mine environment unfavorable is hazardous to worker’s health. This imposes significant demand on cooling and ventilation systems. As a result, substantial costs are incurred while implementing environmental regulation processes to dissipate the heat and provide comfortable working conditions. Thus, as an alternative, the development of cost effective materials to act as efficient thermal insulators is on the rise. Thermal conductivity is an important property that is a direct measure of a material’s ability to facilitate/deter heat flow. In addition to their superior chemical resistance, adequate mechanical strength, abrasion and fire retardant as well as environmental benefits in comparison to existing building materials such as ordinary Portland cement, aluminosilicate based geopolymers are now gaining widespread interest as promising thermally insulating and sustainable materials. This paper begins with an overview of geopolymers, transitioning into a discussion of recent developments in the field of geopolymer development as a thermally insulating material broadly classified into: filled geopolymers and porous geopolymers resulting in structures with enhanced ability to impede heat flow.

May 9, 2020

By L. G. Hagenbuch

Several factors need to come together in creating an integrate mining equipment dispatching system. At the hub of these factors ace the central dispatching formulas. This paper details the development of these central dispatching formulas and explores the combining of these formulas with other elements to create an integrated dispatching decision. WHY DISPATCHING? Truck dispatching implies and in reality should equate to mine equipment efficiency. Good truck dispatching will yield good mine equipment efficiency while poor truck dispatching will yield the alternative. Truck dispatching can either be automated through a computerized, process or it can be manual. Every mine with haul trucks has a truck dispatching system whether it is recognized or not. Even a system wherein the hauler operators determine where they are going for their next load is a truck dispatching system.

Jan 1, 1987

By Laszlo Valentyik

The wide scale acceptance of the heavy media separation is due to its simplicity and efficiency. The two most important variables of the process are specific gravity and consistency of the medium. The latter is a function of the settling rate of the media solids. The almost always present clay in the feed and conse¬quently in the medium acts as a stabilizing agent, and its optimum concentration varied between 3-4%.(1,2) Since polymers essentially perform the same function in oil well drilling muds - i.e. to suspend cuttings during drilling - as the fine clay in heavy media separation, this led to the investigation of whether polymers could be used in heavy media separation as supporting agents. During the first phase of the work, it was found that by the controlled addition of polymers, the stability of the heavy media increased without unduly increasing viscosity of the suspensions, thus yielding conditions for more effective and efficient separation. The results of the experiments were reported in a paper at the AIME Centennial Annual Meeting, March 1971.(3) This paper presents the results of the experiment carried out during the second phase of the work.

Jan 1, 1975

By M. E. Ryan, C. L. Hoebbel, E. J. Haas

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of any company or product does not imply endorsement does not constitute endorsement by NIOSH. ABSTRACT It has been suggested that effective disaster prevention and response in mining requires that elements of emergency management be incorporated into everyday operations, planning, and decision-making, much in the same way that the industry approaches routine risk management. Since Congress passed the MINER Act in 2006, the newly mandated structural and technological advancements in mine emergency response preparation have been made and are apparent, but measureable improvement in mineworker emergency preparedness is difficult to ascertain. To begin exploring whether measurable indicators of mine workforce preparedness can or should be addressed within a risk management framework, NIOSH researchers examined the datasets from two separate research efforts—one which measured the organizational safety climate and self-reported safety performance, and the other which measured individuals’ perceptions of their own self-escape competency. INTRODUCTION In response to the mine disasters in 2006, the United States Congress passed the Mine Improvement and New Emergency Response Act (MINER Act), which strengthened existing regulations [30 CFR, Part 48] and introduced new provisions to improve mine emergency response. Since that time, new technological and structural features, such as mandated redundant communication systems, personnel tracking systems, and lifelines in primary and secondary escapeways, have been installed in underground coal mines across the country. Additionally, mine operators are required to develop emergency response plans, provide adequate supplies of breathable air throughout the mine, provide more frequent and realistic expectations training, and are required to immediately notify the Mine Safety and Health Administration (MSHA) in the event of an accident. While the structural and technological advancements in emergency preparedness are readily observable and easily measured, levels of individual mineworker preparedness remain difficult to assess. There is a general consensus that deficiencies in competence in the non-routine tasks required for individual miners to effectively respond to a mine emergency likely remain (e.g., National Research Council [NRC], 2013), and NIOSH research continues address this concern (Haas, et al., 2015; Hoebbel et al., 2018). To maximize an operation’s capacity to effectively prevent disasters and/or respond to emergency events, it has been suggested that individual and emergency management efforts be incorporated into everyday operations, planning, and decision-making in much the same way organizations manage routine risks to health and safety (Haddow et al., 2017). To the authors’ knowledge, the mindful intersection of routine risk management policies and practices and emergency prevention and response readiness have yet to be empirically studied within the mining industry.

Jan 1, 2019

By A. W. Khair

Surface subsidence is a phenomenon mainly associated with longwall mining, although it can also occur if the coal pillar left to protect the surface deteriorates with time and results in the collapse of the room and pillar system. A method has been developed that utilizes physical mine models and laser holographic interferometry. This method is capable of measuring displacements as small as 5 micro- inches by means of generating displacement contours on a surface, even that of granular materials. Analysis of subsidence in room and pillar mining using models of various extraction ratios ad overburden depths along with two different types of overburden model material (sand and gelatin) has been made. The sand represented the extreme brittle conditions of geologic material while the gelatin represented visco-elastic behavior of geologic material. This paper deals with the analysis of data which has been gathered up to date, and mainly associated with the use of sand as an overburden model material. The analysis included the effect of variation of geometric parameters on surface subsidence. Among these parameters are: variation in seam depth and thickness, surface and seam inclination, and extraction ratio.

Jan 1, 1984

By Yi Luo, FENGLIANG WU

Explosions and fires originated from longwall gob due to the formation of methane-air mixture have been a severe threat to coal miner’s lives.Many numerical studies on coalmine fire and explosion hazards have focused on the airflow in roadways and mine gobs. However, most of these studies isolate the gob from its surrounding roadways, and the network analysis and the CFD method are applied independently tomodel the two classes of airflows. This approach greatly limits the ability of simulatingmine ventilation flow, especially unable to consider the effects of gob boundary conditions on air exchange between the gob and the surrounding airways. An innovative finite tube method (FTM) is developed to couple the one-dimensional mine ventilation network (MVN) and the 2D/3D gob flow field (GFF). In FTM, GFF is discretized into a finite number of flow tubes each of which is formed by any two adjacent stream lines. These tubes, representing the gob’s field flow, connect the MVN into a new coupling network. To solve the coupling model betweenMVN and GFF, an iterative solution technique is developed inwhich the MVN analysis is used to evaluate the boundary pressures for GFF simulation and in turn the FTM feeds the GFF results back to the coupling network. Based on the FTM approach, a model for gas migration in gob has been established for delineating the hazard zones of explosive methane concentration and spontaneous combustion. A computer program is developed to implement the FTM simulation. An illustrative example with five flow tubes representing the GFF is created to verify the stability and convergence of the FTM solution process. A simulation example also indicates that the accuracy of FTM is improved by 12% compared with previous method. Results of an application case show that the program is capable of quantitatively evaluating the gob’s risk zones prone for spontaneous combustion and gas explosion as well as performing risk analysis for various ventilation scenarios.

Jul 10, 2020

By Corby G. Anderson, Sheikh Abdul Rezan Sheikh Abdul Hamid, Sanjith Udayakumar, Ahmad Fauzi Mohd Noor, Teuku Andika Rama Putra

Chemical and mineralogical characterization of Malaysian monazite, a phosphate mineral, bearing rare earth elements separated from the tin tailings originated from Ipoh, Perak, Malaysia, was performed in this paper. The study aims to collect detailed information on the chemical composition, crystal phases, and microstructure of the mineral monazite concentrate that would aid to optimize the subsequent hydrometallurgical processes for high-efficient separation of thorium and other associated rare earth elements. A systematic characterization study of the concentrate was conducted using techniques such as optical microscopy (OM), scanning electron microscopy (SEM) equipped with energy-dispersive X-ray spectroscopy (EDS), and Fourier-transform infrared spectroscopy (FTIR). These techniques analyzed the morphological details on the surface, elemental analysis, and mineral association assessment and identified the surface functionalization groups. The bulk composition and the mineral phases in which the elements are present were studied by wavelength-dispersive X-ray fluorescence (WD-XRF) and X-ray diffraction (XRD) studies respectively. The XRF analysis confirmed the presence of Ce, La, Nd, Pr, and Y (rare earth oxides: REO’s ~ 60 wt.%) while thorium dioxide (ThO2) accounted for 7 wt.% of the total composition. Traces of Ca, K, Al, Fe, Ti, and Mn were also confirmed by SEM elemental mapping. The XRD results confirmed that the concentrate was primarily composed of monazite (Ce, La, Nd, Th (PO4)) along with minor impurity phases of quartz. Automated mineralogical analysis was used as a confirmatory tool to corroborate the preliminary evidences. Based on the particle size distribution analysis supported by SEM, the majority of monazite grains were found to be present in the size range of 170–210 μm. Strong bands of PO4 and SiO4 were observed in the IR spectra corresponding to the phospho-silicate matrix of the REE mineral.

By D. Bristow, D. Baker, K. Awuah-Offei, A. ur Rehman

While a body of work exists on intelligent systems for guiding occupants out of buildings during an emergency, the problem of guiding miners out of a mine during an underground emergency has not been explored. Underground evacuation fundamentally differs from building evacuation because of differences in the regulatory regime and uncertainty regarding the number of occupants. The potential for implementing an intelligent miner guidance system is buttressed by the fact that miner tracking systems, along with communication and sensor networks, already exist in underground mines. This work presents a method based on a local positioning system, in the form of a network of “nodes” at major “intersections,” which can then be used to guide miners to safety. We have developed a path-planning algorithm, based on Dijkstra’s algorithm and the local positioning system that can provide miners with the optimal escape path in an emergency. The algorithm is validated with scenarios at the Missouri University of Science & Technology Experimental Mine demonstrating the potential to include smart technology in mine emergency management and response planning. INTRODUCTION Underground mines are hazardous environments with a higher than usual risk of safety emergencies where miners have to evacuate the mine to save their lives. Mines have always trained miners to evacuate or shelter-in-place in minimum time. Jalali and Norrozi (2009) opined that the three major components that help miners in case of emergency are pre-planned optimal escape routes, decreasing delays, and improving the education of miners. In fact, Goodman and Kissel (1990) suggested that fatalities arising from mine accidents could be reduced by 50% just by decreasing delays in finding the pathways in case of emergency. The proposed work can assist miners in finding escapeways quickly in case of emergency. It is very important to have a pre-planned evacuation strategy that is clearly communicated to miners to ensure the safety of all (Conti, Chasko & Wiehagen, 2005).

Jan 1, 2019

By R. K. Mehta

This paper presents the application of a simple genetic algorithm (SGA) to a coal slurry grinding process in order to find the optimum set of conditions under which the desired slurry properties can be attained. The operating parameters of the process were; slurry % solids, dispersant dosage, ball size, and mill speed. The optimization algorithm, which is based upon the mechanics of natural genetics, was used to find near-global optimum points specific to responses measured In terms of fineness, specific energy consumption, viscosity coefficient, and viscosity exponent. In order to minimize the viscosity of the slurry and simultaneously achieve a condition of maximum packing density, optimization was carried out by the penalty method using an overall objective function incorporating several responses. Computer results and analysis demonstrate the ability of the genetic algorithm to perform better than a traditional technique such as response surface methodology (RSM) and to rapidly locate "the global optimum".

Jan 1, 1992

By J. Kou

In this paper the activation behavior of quartz using Ca(OH)2 as an activator in quartz reverse flotation with anionic collector was evaluated and their adsorption behavior was investigated using a variety of techniques. The adsorption of the collector KS-I on the surface of quartz with and without Ca2+ was primarily characterized using Quartz Crystal Microbalance with Dissipation technique (QCM-D), which is a high sensitivity in-situ surface characterization technique. The flotation performance was evaluated using a laboratory mechanical flotation cell at different process parameters such as pH, collector dosage, and Ca(OH)2 dosage. The anionic collector evaluated was a commercial fatty acid KS-I. The QCM-D data showed that the collector adsorbed on quartz more readily with Ca2+ as activator. The mass and structural property of the collector layer adsorbed on quartz surface at 2.16×10-3 mol/L of Ca2+, 0.3 g/L of collector and pH 12.0 have been studied using the technique of QCM-D. The chemisorption of the collector KS-I on the surface of quartz in presence of Ca2+ were also demonstrated by means of zeta potential, QCM-D and FTIR analysis.

Feb 23, 2014

A case study of a systematic approach to grinding circuit steady-state optimization is presented. After overall review of the flowsheet, two circuits were prepared for detailed testing. Functional performance analysis was chosen as the primary modelling system, and on this basis a quality assurance program for data gathering was implemented. A number of circuit design and operating variables were experimented with statistical analysis of plant test results revealed relationships previously unquantifiable by any other modelling technique. Improvements in classification system and mill grinding efficiencies were demonstrated and significant energy cost savings thus realized.

Jan 1, 1998

By R. R. Guzman

In this study, the "Mine Project Risk Management" methodology, MPRM (Botin et al. 2011), has been applied to characterize the sources of uncertainty and to quantify risk in the mining engineering stages of Block Caving mining method. As the result, rock mass caveability and ore fragmentation were identified as the two most relevant parameters of this process and a methodological model has been developed to quantify the risk associated to each of these two parameters. Furthermore, the applicability of the proposed model has been validated using as a case study the Chuquicamata Underground Mine Project in Chile.

Feb 23, 2014