Search Documents

By D. R. McMullin

The purpose of this paper is to provide a method for mine planners and engineers to evaluate on a conceptual basis if a shaft or a ramp is most suited for their particular underground access requirements. Mine planners and engineers are often raced with the decision of choosing which method of underground access is best suited for their particular requirement. Underground access can be provided by a shaft, ramp, adit, or slope for either exploration and/or actual production operations. This paper will focus on the construction cost and schedule differences between sinking a shaft and excavating a ramp which are currently the most typical access alternatives used in the western United States. It would be wrong to state that one method is superior to the other in every case. There are many variables to be addressed, and the degree of sensitivity of each of them will eventually dictate which method is the most suited to the particular circumstances. This paper compares the construction cost and schedule or sinking a shaft to excavating a ramp at different depths given different ground and hydrological conditions. This comparison provides mine planners with "rules or thumb" that may be applied to the access selection process.

Jan 1, 1994

By Nick Hasenack

In the pelletizing plant of Hoogovens, Estel BV, a varying mixture of hematites and magnetites is used for the production of acid and (occasionally) fluxed pellets. Optimum results regarding productivity, quality and process control are obtained with mixtures containing 30-40 % magnetites. A decrease of the magnetite ratio or an increase of the basicity has a great influence on both productivity and heat and power consumption. Tests have been carried out to find the extent to which magnetite can be replaced by b.f. dust, mill-scale and coke breeze. Pilot plant tests show that about 80-100 % of the production loss due to a decrease in magnetite content or to the increase in basicity can be regained without damage to the quality by adding coke breeze. The amount of coke breeze should be limited tot 1,5 %; if this percen¬tage is chosen higher, the quality of the pellets deteriorates rapidly. The amount of coke breeze to be added should be about 30 % above the theoretical value, based on heat balance considerations. The results achieved by incorporating b.f. dust and mill-scale into the pelletmix were also encouraging, but as some types of mill-scale are very difficult to grind and the supply of b.f. dust is limited, the research has not been carried out extensively in this field. The pilot plant tests on replacement of magnetite by coke breeze have been followed by industrial tests, during which the breeze was added to the ore feed before the dry-grinding system.

Jan 1, 1977

By Y. C. Kim

This paper reviews the past 18 months of geostatistical work in a coal deposit performed jointly by the University of Arizona and the Homer City Owners. The objective of the study was to better predict the in-seam sulfur values of the deposit for the purpose of future emission control. Based on initially available 112 DDH information, variogram models were developed for Sulfur, Ash and Thickness for the entire deposit. The deposit was then kriged using 333 m x 333 m (1000 ft x 1000 ft) panel size. The estimation variance information obtainable from geostatistics was next utilized to improve the development drilling activities that were underway. The results of this effort are presented in this paper. In addition, this paper describes (1) the reasons for preferring kriging over the conventional isopachs, (2) the results of empirical validation of the kriged estimates using 19 additional DDH information, and (3) up-to-date experience on the use of conditional simulation of the same deposit for the future emission control strategy development.

Jan 1, 1980

By Junnan Chen, Hongwei Zhang, Wei Wang, Feng Xie

Thiosulfate is a green gold leaching agent that shows great potential to replace the highly toxic cyanide. Ammonia is traditionally used as the copper ligand in thiosulfate solutions to reduce the reactivity of copper ions towards thiosulfate, but it is a toxic reagent. As a result, efforts to replace ammonia with another complexing agent have received increasing attention. In this study, a novel alternative to ammonia is proposed to explore the potential use of the copper-malic acid-thiosulfate system. Experimental parameters include temperature, initial pH, copper, malic acid, and thiosulfate concentration. The feasibility of the copper-malic acid-thiosulfate system was discussed using Eh–pH and species distribution diagrams. Themodynamics analysis indicates that the mechanism of gold leaching in copper-malic acid-thiosulfate solution is mainly catalyzed by the Cu2( Mal)2H-2 2−/Cu(S2O3)3 5− redox couple. The capability of gold leaching in this system for processing the refractory gold concentrate is comparable to that of cyanidation and the traditional copper-ammonia-thiosulfate leaching processes. Thiosulfate consumption is greatly reduced in the presence of malate due to its strong chelating effect on the copper ions. Moreover, the copper-malic acid-thiosulfate system demonstrates a significant enhancement in leaching kinetics, making it a viable option for processing refractory gold concentrates.

Aug 1, 2023

By Muhammed Şener, Ahmet Gültek

The flotation chemicals are important in mineral processing, and new progress is made in this area day by day. For sanidine purification, some commercial collectors, which can be harmful to the environment, are used. In that respect, the poly(amidoamine) (PAMAM) dendrimers, which are non-toxic for the environment, are good candidates for flotation applications. In this study, the second-generation PAMAM dendrimer was used as a collector to remove magnetite from sanidine by microflotation method, and obtained results were compared with commercial collectors. The results showed that the PAMAM dendrimer is an efficient and selective collector for magnetite. PAMAM adsorption mechanism was determined by zeta potential and FTIR spectra. According to the microflotation results, 87.76% of magnetite recovered at pH 8 by using PAMAM as a collector. It was found that the flotation recovery with the PAMAM dendrimers is similar to the Aero 704 between pH 2 and 6 but less between pH 6 and 9 and more between pH 9 and 12. All experiments were carried out five times and the standard deviation of all results was evaluated with p = 0.05 confidence interval. The second-generation PAMAM dendrimers can be an alternative flotation chemical to the commercial ones concerning usability at a wide pH range, recovery potential, and environmentally benign.

Apr 28, 2023

By Irina Chernyshova, Erik Larsen, Hanumantha Rao Kota, Vladislav Slabov, Garima Jain

The separation of fine mineral particles, especially using environmentally friendly approaches, is one of the main problems in the processing of low-grade ores and the re-processing of mining tailings. This work assesses the potential of biosurfactants as collectors in the flotation of ultrafine (smaller than 20 μm) particles of hematite and malachite. As biosurfactants, we test acetylated acidic (ac-ASL) and lactonic sophorolipids (ac-LSL). In addition, n-dodecyl-β-D-maltoside (DDM) is used as a model non-ionic alkyl disaccharide surfactant, and sodium oleate (NaOl) is used as a reference. The biosurfactants are characterized using surface tension and foam analysis. The interaction of the minerals with the surfactants is characterized using zeta potential, solubility, and single-mineral flotation. The collecting properties of the surfactants are compared for the ultrafine (− 20 μm) and coarser (38–90 μm) particle size in the two-mineral flotation of hematite and malachite against quartz. The ultrafine particle size improves the grade in the oleate flotation of hematite, as well as the grades in the DDM flotation of hematite and malachite, which is explained by the weak interactions of the metal oxides with fatty acids and DDM. At the same time, the flotation with ac-LSL and ac-ASL is highly tolerant to the ultrafine particle size. These results indicate that biosurfactants are an interesting alternative to conventional petroleum-based surfactants in the flotation of Fe and Cu oxides. Moreover, a proper selection of surfactants can help combat the problem of fines.

Feb 23, 2023

By Zhongwei Wang, Dong Wang, Feng Ju

The coal seam in the southern coal field of the Ordos Basin serves as the main aquifer, while the region is known for its high-intensity coal mining activities. The coupling effect of mine water and the strong disturbance caused by high-intensity mining have brought serious challenges to the stability of coal pillars. To address this, a formula for determining the reasonable width of coal pillars under the aforementioned coupling effect and establish a criterion for coal pillar instability in this paper. A case study was on the 11,215 working face at the Xiaojihan coal mine in the area to investigate coal pillar stability. Results indicate that the strength and stability of the coal pillar are affected by the water content, with a small water content increasing its strength and large water content weakening it. In high-intensity exploration of watery coal seams, the best stability of the coal pillar is achieved at optimal water content and mining rates. For the Xiaojihan coal mine, the optimum water content and mining rate are 3.31% and 20 m/d, respectively, ensuring the efficient mining of watery coal seams. Furthermore, this study's findings can provide valuable references for the mining design of coal mines with similar geological conditions in the region.

Feb 13, 2024

By R. L. Wiegel

Some of the mineral deposits that are being processed today, and especially those expected to be processed in the future, have relatively low compositions of the valuable mineral. With these low-grade ores, it is necessary to be able to design processes that are sufficiently low-cost to permit exploitation. One approach to minimizing the capital and operating costs for these processes is to use the capabilities of computer process simulation in the design phase of development, to make important technical and economic decisions regarding the evaluation of alternative process flow schemes, the selection of equipment and the choice of operating conditions. There are mathematical simulation models for most mineral processing operations, including several each for size reduction, size classification and mineral separations. To be able to tie these individual operating models together in an integrated mineral process simulation, however, it is important, in fact in some cases essential, that there be a model which describes how the mineral system responds to size reduction in making the liberated valuable and waste mineral particles available for concentration or rejection operations and the locked particles available for possible recirculation. This, then, is the role played by the mineral liberation model, showing the relationship between particle size, quantity and composition throughout the process.

Jan 1, 2011

In early 1970, General Mills Chemicals, Inc. announced the availability of en improved liquid ion exchange reagent, LIX® 64N, for the recovery of copper from various solutions, such as dump leach liquors. LIX 64N has been shown to be a considerable advance over LIX 64, and is presently in use in three commercial plants. Results have been very gratifying. For example, one of the plants was designed for operational production of 40,000 pounds copper per day, and in fact reached this output within the third week following startup of the plant. In addition to the operating plants, another is scheduled to come on stream this month with L D( 64N being used to extract and recover both copper and nickel. The chemical properties and operating characteristics of this reagent have been fully described in a previous paper. 1 LIX 64N is quite an effective and selective extractint for copper, even with copper contents as high as 15 g/l, but the reagent is somewhat limited in pH range, and loses some of its extraction efficiency as the pH drops below 0.8. Liquors derived from vat leaching, electrolytic tankhouae bleed streams, or some of the new leach schemes derived to solubilize copper from sulfide concentrates are examples of the liquors that present major problems when treated via liquid ion exchange. LIX 64N could extract some of the copper from such streams, but recovery was limited to about 75 percent. Also, in some parts of the world there are streams which are relatively low in copper (-5 g/l) but which are very high in acid (25-50 g/1 H2SO4). Again, LIX 64N can attain only about 75 percent recovery from such streams. For effective treatment, these streams require a reagent which will maintain the excellent selectivity of LIX 64N, and will

Jan 1, 1971

By A. Robison, V. T. McLemore

"The San Juan Basin, New Mexico contains many heavy mineral beach-placer sandstone deposits of Cretaceous age. Beach-placer sandstone deposits are concentrations of heavy minerals that formed by mechanical concentrations (i.e. settling) of heavy minerals on beaches or in longshore bars in a marginal-marine environment. They have high concentrations of several elements, such as Ti, Zr, rare earth elements (REE), Sc, Y, U, Th, Nb, Ta and Fe. These elements are becoming increasingly more important to industry, because they are used in the manufacture of devices our society uses every day, i.e. cell phones, computers, and alternative energy devices, like solar panels. It is unlikely that any of the beach-placer sandstone deposits in the San Juan Basin will be mined in the near future because of small tonnage, low grades, high iron content, and distance to processing plants and markets. However, as the demand for some of these elements increases because of increased demand and short supplies, the dollar value per ton of ore rises, enhancing deposit economics. Current studies at the New Mexico Bureau of Geology and Mineral Resources are focused on the Apache Mesa (formerly Stinking Lake) deposit near Dulce, New Mexico. INTRODUCTION Beach-placer sandstone deposits are accumulations of heavy, resistant minerals (i.e. high specific gravity) that form on upper regions of beaches or in long-shore bars in a marginal-marine environment. They form by mechanical concentration (i.e. settling) of heavy minerals by the action of waves, currents, and winds (Fig. 1; Bryan et al., 2007). Modern examples are found along the Atlantic Coast, USA (Koch, 1986; Carpenter and Carpenter, 1991), southeastern Australia (Roy, 1999), and Andhra Pradesh, India (Rao et al., 2008), where they are mined for titanium, zircon, and monazite (a Ce-bearing rare earth, REE, mineral). Detrital heavy minerals comprise approximately 50-60% of these sandstones and typically consist of titanite, zircon, magnetite, ilmenite, monazite, apatite, rutile, xenotime, garnet, and allanite, among other minerals. Most of these minerals have a high specific gravity exceeding 4 and are dark colored, giving the sandstones a dark color, resulting in them being called black sandstones. Although beach-placer sandstone deposits are found in strata of all ages; the deposits in the San Juan Basin in New Mexico are restricted to Late Cretaceous rocks belonging to the Gallup, Dalton, Point Lookout, and Pictured Cliffs Sandstones (Fig. 2; Table 1; Chenoweth, 1957; Houston and Murphy, 1970, 1977). The beach-placer sandstones are black, dark gray, to olive-brown, resistant to erosion, and radioactive due to radioactive zircon, monazite, apatite, and thorium minerals. Anomalously high concentrations of Ti, Fe, Nb, Th, U, Zr, Sc, Y, and REE are characteristic of these deposits. Similar Upper Cretaceous heavy mineral, beach-placer sandstone deposits are found throughout Montana, Wyoming, Utah, Arizona, and Colorado (Dow and Batty, 1961; Houston and Murphy, 1970, 1977; Zech et al., 1994)."

Jan 1, 2016

By Walter R. Hibbard

Precipitation in the northeastern United States, Florida, California and in many industrialized areas of the world is now more acidic (lower pH) than can be accounted for by natural causes. At the same time, the acidity of many lakes and streams in the northeastern United States has been measured and found to be similar to that of actual rain. These facts have led to conclusions that the two conditions are related. Coal burning utilities, 700 to 1000 miles upwind, have been accused of being the cause, leading to proposals for strict emission controls on the alleged offenders. The costs of these controls would place an estimated $10 to $15 billion capital burden on utility customers in about 15 states plus $2 to $6 billion annual operating costs. There appears to be no direct well-established scientific evidence that the accused are guilty but that the indictment is based largely on circumstantia1 evidence. This study examines the evidence, describes the situation and proposes what must be done to reduce the acid precipitation in an orderly cost beneficial manner. It is interesting to observe that studies by the different adversaries on the acid precipitation issue come to different conclusions largely because they do not read the same literature, but selectively develop evidence to support their own points of view, This study will try to review the issues impartially and reach a position of scholarly balance.

Jan 1, 1982

By W. R. Reed, Y. Zheng

A recent study conducted by the National Institute for Occupational Safety and Health (NIOSH) evaluated the roof bolter canopy air curtain (CAC) systemin a blowing face ventilation system, demonstrating its effectiveness and illustrating the CAC protection zones. This study evaluates the roof bolter machine CAC while operating in an exhausting face ventilation system. This study considers two similar locations to allow comparison with the previous blowing face ventilation (Zheng et al., Min Metal Explor 36(6):1115–1126, (2019)) study: (1) a roof bolter machine bolting the roof at 20 ft (6.1 m) from the face and (2) a roof bolting machine bolting at 4 ft (1.2 m) from the face. The environment introduces 6.0 mg/m3 of respirable dust to represent the roof boltingmachine operating downstreamof the continuous miner. However, the exhausting face ventilation uses an exhaust curtain with 9000 cfm (4.25 m3/s) of air. Two roof bolter machine working positions are simulated with the use of dual drill heads in the inward position for two inside bolts and in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s) with dust reductions ranging from 39.5 to 82.8%. When the roof bolter machine operated close to the face, increasing CAC airflow was required for adequate protection since the dust reductions can be as low as 39.5%. Additional CAC airflows of 350 cfm(0.17 m3/s) and 450 cfm(0.21 m3/s) were evaluated and demonstrated that dust reductions increased to 59.7% (350 cfm) and 72.0% (450 cfm) for the worst location where the roof bolter operators located.

Aug 26, 2020

By Lana Alagha, Fardis Nakhaei, Jose L. Corchado-Albelo, Noelia Munoz-Garcia, Michèle Heitz

Sulfide tailings from past and present mining activities are important hosts of critical elements and precious metals. This review paper presented a literature survey on the recovery practices of some critical minerals containing Te from sulfide tailings with a special focus on the physical beneficiation and hydrometallurgical separation methods. Finally, a conceptual framework and possible processing flowsheets were proposed. The findings of this review will be useful for the researchers in the field of geochemistry, mineral processing, and metallurgy to evaluate the separation processes for reprocessing of mine tailings for the recovery of critical minerals.

Feb 1, 2024

By Jordi Vives-Costa, J. J. de Felipe, Lluís Sanmiquel, Maria Niubó

The article evaluates the convective heat transfer coefficient of ventilation air in a potash mine. The energy balance is obtained through thermal characterization of the ventilation air and rock, allowing for the calculation of heat transfer parameters. Different models for calculating the convective heat transfer coefficient are analyzed. The results indicate that the Pethukov–Kirilov, Gnielinski, and modified Dittus–Boelter models are optimal for this mine. The study also indirectly examines the conductivity of the adjacent rock, suggesting saturation throughout the studied section and the presence of liquid water upwelling in a specific section.

Apr 7, 2022

By Dan Wang, Qiuju Li, Xiao Guo

The chemical states and ions interaction were significant interest to understanding columbite mineral/acid solution interface dissolution and reaction. The present research work was focus to explore the specific cations ( Nb5+, Fe2+, Fe3+) distribution near the ferrocolumbite mineral/acid solution interface, and determine these cations leaching sequence in sulfuric acid solution. X-ray photoelectron spectroscopy had the potential to provide detailed dissolution information by resolving chemical state and ion distribution of ferrocolumbite during sulfuric acid leaching process. The binding energy decreased in sequence as Nb5+- O < Fe2+- O < Fe3+- O, and increased in sequence as Fe3+- SO4 < Fe2+- SO4 < Nb5+- SO4 which revealed Nb in ferrocolumbite mineral more easily leached comparing to Fe. The ratio of Fe2+- O/Fe3+-O on leaching residue decreased, and Fe2+- SO4/Fe3+-SO4 ratio increased as sulfuric acid contraction increasing suggested that the Fe2+ oxidized to Fe3+ and released Nb from mineral and dissolved into leaching solution. The ratio of Nb/Fe was lower 0.07 with sulfuric acid contraction increasing which meant Nb dissolution promoted by oxidation of iron. The dissolution mechanism of Fe element in ferrocolumbite mineral was Fe2+- O broken and generated Fe2+. Fe2+ was oxidized to Fe3+ in concentrated sulfuric acid leaching solution. The dissolution mechanism of Nb in ferrocolumbite was that Nb5+- O was directly digested by H+, and the released Nb5+ complex with SO4 2− ion formed cation − anion pairs. The coordination of formation Nb5+- SO4 pairs and oxidation Fe2+ in mineral could promote ferrocolumbite dissolution.

Aug 5, 2023

By Ping Li, Baokun Zhou, Lei Yang, Changfeng Li, Erhui Zhang

A uniaxial compression experiment was conducted on standard sandstone specimens to explore the sandstone’s mutation characteristics and early warning interval during deformation and failure. Meanwhile, acoustic emission (AE) and digital image correlation (DIC) techniques were introduced to realize multi-field analysis and cross-validation from the stress field, deformation field, and elastic wave field. The mutation characteristics of rock failure were investigated based on the cusp catastrophe theory. The results showed four mutation points in the destabilization process of sandstone: compressional density, yielding, destruction, and residual retention. As an internal activity characteristic of the sandstone failure process, AE directly reflected the dynamic failure process of sandstone. The stress variation was closely related to the evolution of AE characteristics. Sandstone loading failure was a process of the mutations of releasable elastic strain energy, dissipative energy, and releasable elastic strain energy. The mutation of dissipative energy was used as the starting mark of the sandstone warning state, and the second mutation of releasable elastic strain energy was used as the end mark of the sandstone warning state. Besides, the warning range corresponded to the loading time of 178 to 208 s. Finally, the sandstone instability warning interval was re-determined from deformation field evolution characteristics in the sandstone damage process, with a loading time of 180–204 s. This was consistent with the warning interval specified using the cusp catastrophe theory. The combination of AE, DIC, and cusp catastrophe theory revealed the mutation characteristics and early warning interval of sandstone failure. Hence, the results provide significant importance to predicting rock failure.

Aug 23, 2023

By Smart Chika Obiora, Anthony Chukwu

Mining and processing of raw materials is one of the earliest activities of man for survival and development. The products are used for making jewelleries, metal tools, and for exchange of goods and services. However, despite the benefits of mine recoveries, it’s negative and long term effects on the environment and lives remain the point of discussion throughout the world. This study summarizes findings of researches in active/abandoned lead–zinc mines in Enyigba and Ishiagu mining districts including social surveys in the localities surrounding the mines in order to ascertain the effects on the inhabitants. Lead–zinc mining in Enyigba and Ishiagu, southeastern Nigeria has lasted for decades and has affected the socio-economic well-being of the host communities. There are evidences of soil, water, and plants contamination by Pb, Zn, Cd, and Mn in these mining communities. The mining activities also affect the overall social development of the host communities. These effects include retardation in educational development, health care provision, unemployment, and access to potable water supply. Others are rise in poverty level, social amenities, sanitary/hygiene level, high cost of living, and fertility rate. Possible mitigation strategies such as to liaising with relevant government agencies in collaboration with mine owner, mine workers, and host communities can ameliorate these negative effects and promote environmental sustainability.

Feb 24, 2023

By Pei‑liang Xu, Jun Wang, Xi Zhang, Deng‑pan Qiao, Tian‑yu Yang

The surface backfill, serving as the operational platform for continuing mining in upward slicing and filling stopes, is required to possess sufficient strength and thickness. Currently, there are limited model methods for determining the strength and thickness of the surface fill body. By analyzing the mechanical actions on the surface backfill, it is determined that its stability is mainly influenced by the combined effects of normal and tangential uniform loads under full-load conditions of trackless equipment. Assuming a circular contact surface between the tire of the trackless equipment and the surface backfill, and utilizing solutions from elastic mechanics theories such as the Boussinesq and Cerruti solution, the stress and displacement distribution of the surface fill body were obtained. Based on the maximum vertical stress condition, where the surface backfill body undergoes maximum deformation while still in an elastic state, and considering the stress–strain relationship, a model for the strength and thickness of the surface backfill has been established. According to the research findings, the design for the strength and structural parameters of the surface backfill has been developed to meet the full-load operation of the Atlas ST7 scooptram, with a compressive strength of 1.32 MPa and a thickness of 0.5 m. Numerical simulation analysis results indicate that the stress and displacement of the surface backfill align with theoretical analysis results. Practical results from industrial application in the western section of the Dahongshan Copper Mine demonstrate that the designed strength and thickness of the surface backfill meet the operational requirements for trackless equipment, resulting in significant engineering application effects and economic benefits. The research findings hold significant importance for advancing the theory of backfill mining and have high applicability and promotional value for similar mines.

Mar 24, 2024

By S. J. Schatzel, J. D. Addis, V. Gangrade

In longwall mining, ventilation is considered one of the more effective means for controlling gases and dust. In order to study longwall ventilation in a controlled environment, researchers built a unique physical model called the Longwall Instrumented Aerodynamic Model (LIAM) in a laboratory at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) campus. LIAM is a 1:30 scale physical model geometrically designed to simulate a single longwall panel with a three-entry headgate and tailgate configuration, along with three back bleeder entries. It consists of a twopart heterogeneous gob that simulates a less compacted unconsolidated zone and more compacted consolidated zone. It has a footprint of 8.94 m (29 ft.) by 4.88 m (16 ft.), with a simulated face length of 220 m (720 ft.) in full scale. LIAM is built with critical details of the face, gob, and mining machinery. It is instrumented with pressure gauges, flow anemometers, temperature probes, a fan, and a data acquisition system. Scaling relationships are derived on the basis of Reynolds and Richardson numbers to preserve the physical and dynamic similitude. This paper discusses the findings from a study conducted in the LIAM to investigate the gob-face interaction, airflow patterns within the gob, and airflow dynamics on the face for varying roof caving characteristics. Results are discussed to show the impact of caving behind the shields on longwall ventilation.

By Xiang He, Xinzhong Wang, Ning Li, Bao Cao, Hongyang Bai, Zhigang Du

Revealing the periodic fracture pattern of the main roof and the key influencing factors of the support resistance is crucial for strata control and support selection of the shallow buried working face with large mining height. Based on the cantilever beam theory, an improved step rock beam model, and the measured strata pressure data of the 12,401 working face in Shangwan Mine, the mine pressure behavior law of the shallow buried with a large mining height working face was analyzed. The results show that both ratio of maximum principal stress to load (σ1/q) and ratio of maximum shear stress to load (τmax/q) inside the main roof increase with increasing periodic advancing distance, while the ratio of maximum shear stress to maximum principal stress (K) is the opposite, indicating that the increase rate of σ1/q is higher than that of τmax/q. K is less than 1 when the periodic advancing distance exceeds 8 m, indicating that the periodic fracture of the main roof will be dominated by tensile failure. Support resistance increases with increasing immediate roof thickness, main roof thickness, periodic fracture step distance of the main roof, and mining height, and decreases nonlinearly with increasing friction coefficient of periodic fracture rock block hinge surface. The main roof thickness, the periodic fracture distance of main roof, and the friction coefficient of the hinge surface of the periodic fracture rock block are the key factors influencing the support resistance. The advance breaking of the main roof and increasing the friction coefficient of the hinged surface of the main roof can reduce the support resistance of the working face. The support resistance of the 12,401 working face in Shangwan Mine presents an arch distribution characteristic. The average periodic weighting step interval, average support resistance, and dynamic load coefficient are 15.6 m, 17,552 kN, and 1.3, respectively. Finally, the rationality and validity of the model are verified by comparing the measured and theoretical values of the support resistance in the 12,401 working face of Shangwan Mine and other shallow coal seams with large mining height.

Apr 22, 2024