Search Documents

By Andy Ingriselli, Andrew Famiglietti, John Westland, Greg Landry

Atlas Dewatering was contracted to install and maintain a groundwater control system for the new Bessarion Subway Station and the Tail Track Structure on the Toronto Transit Commission’s new Sheppard Subway Line. Atlas met the challenges presented by the project by closely reviewing the contract documentation provided by the Program Geotechnical Consultant, Golder Associates and by working with the general contractors, Bondfield Construction Company and PCL Constructors Eastern, inc., throughout the duration of both projects. In addition to concerns about soil loss, excessive settlement and seepage, the consultant was concerned about spreading hydrocarbon-contaminated groundwater between the two aquifers present at the Bessarion Station site. By installing a system of multi-level vacuum eductor wells around the perimeter of the excavation, Atlas was not only able to provide a dry excavation for construction, but, due to a unique well design was also able to prevent cross-contamination of the aquifers.

Jan 1, 2001

By S. C. Westerfeld

The original patent for the gyratory crusher was granted to Philetus W. Gates in 1881. This first crusher was used by the Buffalo Cement Co. At the time these early gyratory crushers were developed all mining and quarrying, either underground or open pit, was done by hand; tonnages generally were small and product specifications simple and liberal. Likewise plants were small and demands for small product sizes practically nonexistent. In addition to substantial amounts of hand labor, the available material handling equipment was small, simple, and not suited to handling large run of mine ore. Mine can, cable ways, or belt conveyon transporting crushed material to the mill had limited capacity per hour. At the turn of the century the largest Gates crusher, the No. 9, had a receiving opening of 21 x 48 in. with a three-arm spider and a 21 x 80-in. opening with a two-arm spider. The steam shovel began to change the entire picture of open pit quarrying. As a result of the use of steam shovels around 1910 crushers with 48-in. receiving openings were built; thus it can be seen that the basic gyratory crusher was developed prior to World War I. The improvement of the internal combustion engine and the use of pneumatic tires created a new set of operating conditions. Early mines were small, using shrinkage stoping and small mine can. The capacity of material handling was small, limiting the size of the largest piece and the feed rate. Improved material handling resulted in more and more large open pit mines with large shovels and a tremendous increase in the size of off road or mine haul trucks or rail can. Primary gyratory crushers also increased with receiving openings as large as 60 in. and connected hp of 1,000.

Jan 1, 1985

By S. Dubnewych, S. Kieffer, M. T. McRae, R. R. Redd

The seismic vulnerability of the existing outlet tower at Lake Mathews reservoir, located in Riverside County, California, necessitated the design of a new outlet facility to assure serviceability of the facility following a major earthquake. The components of the proposed facility include: a new outlet tower; a shaft; a new outlet tunnel; an approach channel that will be excavated underwater; and two short tunnels that will connect the new outlet tunnel to the existing outlet tunnel via the shaft. As the new facilities will be constructed while the reservoir is in operation, a cofferdam will be constructed around the site of the new outlet tower. The design for the underground facilities used a combination of empirical methods; limit equilibrium analyses, including displacement-based pseudo-static analyses for dynamic loading conditions; and numerical analyses. This paper outlines the design methodology used to develop an innovative design for the facilities which can be constructed within the time frame required by the operational schedule of the reservoir and existing outlet facility.

Jan 1, 1999

By Stephen Slot Odgaard, Simon D. Taylor

Phase One of Copenhagen Metro opened on October 19th, 2002 and is already a great success. 11 stations are open and Phase Two with 6 additional stations will open during 2003. Phases One and Two include 21 km dual track, whereof 10 km is in tunnel. 17 stations (six deep, three shallow, and eight above ground) will service passengers with trains running at 90 seconds intervals. This paper will discuss the various aspects of the Metro, where construction methods include TBM bored, NATM, Cut & Cover, Secant Piles and Diaphragm Walls.

Jan 1, 2003

By S. S. Peng

This paper presents a computer program package for predicting surface movement and deformation caused by under-ground coal extractions. It is capable of: predicting final surface movement and deformation over underground openings; predicting dynamic surface movement and deformation process associated with underground lingual mining operations; processing and bookkeeping subsidence survey data; recommending subsidence parameters for those new coal mines where no subsidence data are available; and deducting subsidence parameters from collected subsidence data.

Jan 1, 1986

By J. Herbst, C. C. Harris, G. Poling

The modern flotation machine is the result of decades of adaptation to a changing environment. In response to falling ore grades, and rising demands, tonnages, and costs, attempts are now underway to expand machine capacity by about an order of magnitude, while at the same time maintaining metallurgical performance and if possible reducing power requirements per unit throughput. Empiricism and rule-of-thumb have guided flotation machine design and scale-up, and a current need is for the development of a fundamental understanding of the subject. Design features of current and some obsolete machines are discussed in an attempt to outline those principles of flotation machine design which are known, and to delineate topics needing investigation. Attempts are made to distinguish between essential machine features required by the physics of the process, those features resulting from speculative theories on the flotation mechanisms, and features which are essentially styling variations. Topics discussed include: flotation mechanisms; tank and impeller/ stator design and dimensions; impeller speed; aeration; power consumption; particle suspension and dispersion; capacity; correlation of design parameters and operating variables; scale-up and scale- down; materials flow; problems in machine design. Design details and operating data for several current machine families are provided in Appendices.

Jan 1, 1976

By K. L. Myers, R. Espell, C. Deringer

Construction of the AA Pad reclamation was completed in the fall of 2000. Seeding of the ET cover began in the late fall of 2000 and continued through May of 2001. On Saturday afternoon, June 1, 2002, a large, very localized thunderstorm struck the reclaimed AA Pad site. Eyewitnesses present at the time described a dark storm cloud parked above the site for less than half an hour. Average rainfall intensity was measured to be 122 mm (4.8 inches) per hour and peak rainfall intensity was estimated to be 213 mm (8.4 inches) to 259 mm(10.2 inches) per hour. At the time of the storm, the construction was less than two (2) years old and the vegetation had only a single season of growth. The entire period from the end of construction until the date of the storm was a drought period with below normal precipitation. Other than a few small snowmelt events, there was no precipitation event large enough to produce any significant flow in the channel network. Therefore, the very first significant runoff event was the extreme event of June 1, 2002. The storm essentially represents a large-scale field test of the design concepts used at the AA Pad site. Shortly after the storm, data was collected and analyzed with the intent of learning as much as possible about the performance of the cover system design with the expectation that the newly acquired knowledge might be utilized in future designs to further improve the performance of similar cover systems during extreme events.

Jan 1, 2003

By N. Djordjevic

Introduction The vibration energy that travels beyond the zone of rock breakage is wasted - all it does is cause damage and annoyance. Under favorable geologic conditions, this energy may travel many kilometers before it finally drops bellow the background noise level. This has forced the introduction of more restrictive limits to the allowable vibration levels. To maintain the profitability of a mine or quarry and to comply with environmental protection legislation, blasting needs to be performed in a more predictable way that will ensure that the final results are optimal in both mining and environmental terms. Minimization of ground and induced structural vibration is, therefore, a matter of good blasting practice -not just an attempt to avoid complaints from neighbors. A new approach to blast vibration minimization is presented. The method utilizes the existence of the local minimums in the frequency spectrum of single-hole blast vibration. The results are presented as a delay map showing maximum ground or structural vibration velocity for many combinations of interhole and interrow delays. A blast engineer can use this map to select an optimal combination of delays that will produce a low vibration velocity at a selected location and, at the same time, will be acceptable from the point of view fragmentation or muck pile shape. Response of structures A typical single-story building has two distinctive forms of vibration. The first form is a translatory vibration of the building superstructure (frame), and the second form is a flexural-bending vibration of the structural elements such as walls and floors (Siskind et al., 1980). Walls and floors will have several modes of oscillation. The most important is the fundamental mode of the vibration, as this mode will have the lowest frequency, the largest amplitude and will cause the largest deformations. The vibration of walls and floors is also a source of secondary vibration within a building, due to the movement of loose objects, e.g., furniture and wall fittings (Dowding, 1985). The subjective estimate of the amplitude of a vibration by the occupants of a house will be unrealistically high due to the effect of the secondary vibrations. It is now well recognized that human perception of ground vibration begins at levels that are far below those that will produce minor damage to the most fragile structures. In mining and quarrying operations, complaints regarding vibration levels tend to be determined more by human perception or annoyance rather than by observations of damage. Ground vibrations on the order of 0.08 mm/s (0.0032 ips) (Walter and Walter, 1979; Murray, 1987) can be felt, and they are often subjectively estimated to be about 100 times greater. Amplification of ground vibration in the structure depends on the amount of energy in the ground vibration spectrum that is in the vicinity of the structure's resonant frequencies together with the damping ratio of the structure at these particular frequencies. One way to avoid significant vibration amplification in a structure is to shift the dominant part of the ground vibration away from the resonant frequency range of the structure. The presented method allows for the selection of the optimum blast timing (interhole and interrow delay times) to minimize the resultant ground vibration amplitudes in a given frequency range. It also allows the selection of suboptimal, but still acceptable, blast delay times, which may be preferable from the point of view of overall blast performance. Determining frequency ranges of importance in structures In attempting to avoid amplification of vibrations in the structure, ground vibration amplitude of frequencies close to the resonant frequencies of the building needs to be minimized. The width of the frequency-minimization region is determined by the value of damping in the building. If the damping ratio is low, then the frequency-minimization region around the resonant frequency will be relatively broad. By shifting the dominant part of the ground-vibration energy into the frequency region much higher than the resonant frequency of the building (1.5 to 2 times), it is possible to achieve efficient vibration isolation of the building. In such cases, the structural dynamic amplification of ground vibration will be less than unity. The first step in this minimization process is the determination of the structural resonant frequency. From the frequency spectrum, it is possible to determine the resonant frequency of the structure. Sometimes the

Jan 1, 1998

By James J. Scott

I am indeed honored to be the 1991 recipient of the Daniel C. Jackling Award. To be voted this honor by my peers in the Society for Mining, Metallurgy, and Exploration and AIME means more to me than I can truly express. Daniel Jackling's position and prominence in the mining industry first came to my attention in the fall of 1949 when I transferred from Wisconsin Institute of Technology, then a three-year school, to the Missouri School of Mines to complete my last year for a bachelor's degree in mining engineering. I played basketball in the Jackling gym and ran track on the Jackling field. I didn't know a lot about Jackling then, except he was an honored graduate of the school and, obviously, supported the school financially. Over the years, Jackling's name kept coming up. He was a man with a reputation for being a doer, a mining leader who was always a step ahead, a mining engineer who knew how to motivate men in the working place, to organize mining systems, to finance and organize corporations. to open up new, low-grade ore bodies for exploitation. If Jackling were alive today, I would expect he would bean excellent candidate to apply practical rock mechanics to his projects. Looking over the list of Jackling Award recipients, I have known many, have met many personally and had a few who were dear friends that affected my own professional life. Ab Shoemaker, '58, and I consulted at the White Pine Copper Co. on mining problems in the 1960s. We arranged for our visits to the mine to coincide so that we could collaborate on our ideas. I would rent an auto and drive for Ab. He said he was the only mining engineer in the country that had a PhD for a chauffeur. James Boyd, '67, was my mentor as regards the White Pine Rock Mechanics Program that we organized in 1963. Only through Boyd's forsight. leadership, dedication and willingness to spend money on research and development did the Practical Rock Mechnics Program at White Pine succeed. He never wavered in his support to that program or to me personally. Tom Howard, '75, was my predecessor in 1970 as Director of Mining Research for the US Bureau of Mines. When I joined the Bureau in August 1970, he had the research centers up and running. Any successes I may have had with the Bureau of Mines were due in great part to Tom's leadership and organization throughout the 1960s. Gene Cameron, '68, was my teacher at the University of Wisconsin and I remember him fondly. He was the one professor who lectured in a manner that made me welcome going to his classes each day, a truly remarkable educator. If you have come today to listen to me talk about instrumentation, rock properties, stress-strain relationships, rock mechanics theory, etc., you will be disappointed. Large volumes of data have been collected by well qualified theoreticians to define stress-strain conditions in mines. Unfortunately, very little of this data has been used by industry due to the lack of initiative and understanding by the researchers to the true problems of implementation in the industry. I hope my remarks will assist future investigators to work through the maze of operational problems so they will experience the satisfaction of seeing their research used. I fully realize that the Jackling Award is given by the Society for Mining, Metallurgy, and Exploration and is primarily offered for accomplishments in hardrock mining. I have found it impossible to separate hardrock and coal mining when I talk about "Applied Rock Mechanics." There is too much overlap and the same mechanics principles are applied to both. For example, coal mine designs have been applied to salt, trona and potash. Also, the original layout and design of White Pine Copper Mine was based on coal mine designs. Any developments to apply rock mechanics ideas must

Jan 1, 1992

By Bernard L. Cohen

INTRODUCTION The most serious occupational radiation episode in U.S. history was the exposure of uranium miners to radon daughters in the 1945-1968 time period. Although the maximum permissible dose at that time was 12 WLM (working level months) per year, average exposures were several times that figure, and ten times higher exposures were not uncommon. Starting in the early 1960s, mounting epidemiological evidence appeared for an excess incidence of lung cancer among these miners; up to 1974, there was an excess of 134 cases (159 observed vs 25 expected) among the 4000 in the group under study (NAS-1980). When this excess became apparent, the Federal Government took jurisdiction, greatly tightened enforcement, and in 1969 lowered the maximum permissible exposure to 4 WLM per year. These standards were met largely by a great improvement in ventilation. As a result of these measures, average miner exposures were reduced 5-fold from 1965 to 1968 and by another factor of 3 by 1970. In 1978, the 4 WLM/year maximum permissible exposure was exceeded by only 37 of 7500 underground miners, for only 16 wars it exceeded by more than 25%, and for only 8 was it exceeded by 502 (AIF-1980). The average exposures to the various groups are listed in Table 1. We see that the average exposure for all miners was 1.03 WLM, and for those who worked essentially full time underground it was 1.45 WLM. For purpose of later discussion, it will be convenient to choose a single value for average exposures. In view of the fact that employment situations and job categories are bound to vary over a lifetime of work, we take this to be 1.3 WLM/year. The purpose of this paper is not to dwell on history, but rather to address the question of whether or not this present situation is satisfactory. This question was considered recently by a study group under the auspices of National Institue of Occupational Safety and Health (NIOSH-1980) and it answered the question in the negative, concluding that the maximum permissible exposure should be substantially reduced. However, their arguments were incomplete and were lacking in perspective. The principal thrust of this paper is to provide some of the material overlooked. RISK TO URANIUM MINERS FROM RADON EXPOSURE In order to quantify the risk to uranium miners under present working conditions, it is first necessary to estimate the risk of lung cancer per WLM of exposure. The most straightforward way of doing this is to use the data on the group of uranium miners under study. These are listed in Table 2 for 8 exposure ranges and for the total group (NAS-1980). If all data are given equal weight, the risk is seen to be 3.5 x 10-6 per year per WLM. Much can be said in favor of using this value for the risk as dose independent; it is within one standard deviation (SD) of the observations in 5 of the 8 dose categories (as expected from the definition of SD), and within 2 SD for all 8, and for the three cases differing from the mean by more than one SD, two are above and one is below. However, the uranium miner exposures in the present situation will be far below those covered in Table 2, so it is worth considering the possibility that the risk differs from this at low doses. From the last column of Table 2 we see that the experience from all exposures below 600 WLM indicates a risk higher than the mean for the entire group by more than two standard deviations (the value 600 WLM in this comparison was deliberately chosen to maximize this deviation; for exposures below 360 WLM and 840 WLM, the excess is only 1.0 and 1.6 standard deviations respectively). In view of this tendency for the risk to be higher at lower dose, we will take the risk to be 5.0 x 10-6 per year per WLM in what we will refer to as model A. This risk estimate is based entirely on exposures much [higher] than those that will be experienced by

Jan 1, 1981

By I. Meliadis

This study presents the methodology and proposals for the restoration of an abandoned quarry in the Greek island of Milos. The local data (soil, vegetation etc.) of the island were collected, analysed and compiled into thematic maps using Geographical Information Systems. The restoration plan was based on the G.I.S. database and suggested the revegetation of the disturbed lands with herbaceous (grasses and legumes) or woody (shrubs and trees) plants. Plants should be indigenous or from other areas with the same vegetation type. Herbaceous plants establish and grow easily protecting the soil from surface erosion. The revegetation success depends on the seed quality, planting season and methods as well as local environmental conditions. Our proposals aim to restore the abandoned quarry with methods that follow the natural succession of vegetation, have minimal environmental impact, low cost and the expected result will be similar to the surrounding undisturbed land.

Jan 1, 2002

By Brain W. Lawrence

Sublevel stoping generally is a large-scale open stoping method. It sometimes is referred to as long-hole or blasthole stoping. This method usually is applied to strong ore bodies that require minimal support and are surrounded by strong country rock. The ore body should be fairly regular in shape and well-defined. The dip of the footwall normally should be sufficient to allow broken ore to gravitate freely, although the method has been adapted successfully to mine some of the flatter ore bodies. Sublevel stoping is not dependent on the width of the ore body. Widths of less than 6 m (20 ft), however, make the utilization of long-hole drilling techniques more difficult. The main criteria for sublevel open stoping are competent ore and stable host rock, regular ore boundaries, and a footwall dip that exceeds the angle of repose of broken ore. Basically, the method entails providing access to the ore body at various subintervals between the main haul- age levels in order to drill and blast the intervening ore. Stope drilling is carried out from drilling drifts on the sublevels, and the ore is blasted in slices towards an open face, which generally is vertical on the downholes and may be inclined towards the open face for the up holes. The blasted ore gravitates to the bottom of the stope and is collqcted through drawpoints. Fig. 1 illustrates a typical sublevel stoping mine. The method requires extensive ore body development with relatively high capital expenditures. How- ever, much of the development is in ore, and production costs are comparatively low. Productivity rates are in the 13.6 to 27.2 t (15 to 30 st)/manshift range. The drilling, blasting, and loading operations are performed independently, and equipment utilization is high. Large outputs can be obtained with few units and limited personnel. Dilution with waste rock may occur if ore boundaries are irregular or if caving occurs, but 100% of the ore within the stope usually is recovered. Pillar recovery sometimes is a problem. It is at this point that most of the waste dilution occurs. At the time data was gathered for this report (1973), the sublevel open stoping method was used by more than 21% of the metallic ore mines in the US (9 out of 42 mines producing 1088 + t/day (1200 + stpd) and provided more than 12% of the total metallic ore production from these mines. DEVELOPMENT Access to a sublevel open stope mine is gained by a slope or shaft that is normally sunk in the footwall of the ore zone, away from any possible effects from blasting or other production operations in the stoping process. Main level interval is selected and usually varies from 45.7 to 121.9 m (150 to 400 ft), depending on the vertical extent of the ore body, the number of drawpoints required to maintain output, and the eventual stope height. The main haulage drifts are located at the bottom of the stope horizon, either directly in ore or in the footwall, with access crosscuts at intervals. Raises are driven up through the ore to connect to the level above and provide access and ventilation to the sublevel drilling drifts, which are driven horizontally in the ore for the length of the stope. Depending on the drawpoint system to be used, the stope is either undercut by a raise-and-cone system, from a scram or slusher drift, or simply provided with a drilling drift from which access is made at intervals to the main haulage level. A raise driven either at the end or in the middle of the stope (if stope access is from both ends) provides a start for opening up a vertical slot across the stope to establish a free or open face for long-hole drilling and blasting. Sublevel stoping has proved to be a relatively safe and economical system.

Jan 1, 1982

By Martin Herenknecht, Michael Knabe, Ulrich Rehm

In Switzerland at present, the longest railway tunnels in the world, the Gotthard(57 km) and the Loetschberg base tunnel (34km) are under construction. For thischallenge six high-tech HERRENKNECHT Hard Rock Tunnel Boring Machines (TBM)are applied, which have to excavate approx. 80 km at the Gotthard and 20 km at the Loetschberg Tunnels. The machines being used are of a single Gripper-TBM type, which are equipped with the latest rock support techniques, in order to optimize the quality of the working conditions for the personnel which have direct impact on the quality of the tunnels. The different requirements of the projects based on different speci?cations within the tender documents led to completely different TBM concepts which will be reviewed in detail in this paper.

Jan 1, 2003

By Leonard W. III Joseph, William H. Buttermore

Noise control is an important consideration in the design and operation of coal preparation plants. It is essential to understand and control noise sources to provide a safe environment for operating personnel. The average noise exposure levels in a typical coal preparation plant generally range between 95 and 100 db. An operator should not be exposed to noise levels of this magnitude for more than 4 and 2 hr, respectively, according to MSHA (Mine Safety and Health Administration) regulations. The major noise sources in a coal preparation plant include noise from impacting the inside surfaces of steel chutes, vibrating screens, coal crushers, pumps, motors, fans, and blowers. The magnitude of noise varies considerably from one situation to another. NOISE EXPOSURE IN COAL PREPARATION PLANTS Noise regulations established by the Occupational Safety and Health and- ministration (OSHA) are accepted by MSHA relative to coal preparation plants. Fig. 14-43 shows a graph of the time of noise exposure in hours per day to which a worker can be exposed for each A-weighted sound level. According to this graph, a worker is permitted to spend 8 hr in a 90-db noise environment, but that time must be halved when the A-weighted sound level increases 5 db. The noise dosage a worker receives is determined by the ratio of the length of time the worker spends in a particular noise environment divided by the length of time he is permitted to spend in that environment. If the worker is exposed to several different sound levels, his total dosage would be the sum of each of the individual dosages. The equation for determining the dosage is: where C is the actual duration of exposure at a given steady state noise level and T is the noise exposure limit for the level present during the time C According to MSHA regulations, the dosage, D, should not exceed one (1) for any worker for a full day of work. As an example of typical plant noise levels, vibratory screens and crushers emanate noise levels in excess of 90 db at a distance of 3 ft (0.9 m) with no material flow. With material flow, noise level increases 1 to 10 db depending

Jan 1, 1991

By Byron C. Hardinge, E. R. Palowitch, Albert W. Deurbrouck, David J. Akers, Edward R. Torak

During 1983, 42.2% of the 686.0 (624.3 Mt) million tons of coal reported, 289.6 (263.5 Mt) million tons were mechanically cleaned, of which 107 (97.4 Mt) million tons were cleaned by dense media (magnetite and sand) processes.' The percentage of bituminous coal and lignite cleaned mechanically by dense medium processes increased from 7 to 38% between 1938 and 1983. The Electric Power Research Institute estimates that 150 million tons (137 Mt) of coal were cleaned by heavy-media processes in 1986, and that this number may increase to 265 million tons (241 Mt) by 1990.2 Dense medium separations include those coal preparation processes that clean raw coal by immersing it in a fluid having a density intermediate between clean coal and reject. As there is a general correlation between ash content and specific gravity, it is possible to achieve the required degree of removal of ash-forming impurities from a raw coal by regulating the specific gravity of the separating fluid. Dense medium processes generally offer the following advantages over other coal cleaning processes: • Ability to make sharp separations at any specific gravity within the range normally required even in the presence of high percentages of raw coal whose specific gravity is near the specific gravity of separation. • Ability to maintain a separating gravity that can be controlled within + 0.005 sp gr units. • Ability to handle a wide range of coal sizes. • Ability to change specific gravity of separation to meet varying market requirements. • Ability to handle fluctuations in feed, in terms of both quantity and quality. Unfortunately, dense medium processes can have the following disadvantages: • Relatively high capital costs caused primarily by the need for equipment to collect and recycle the medium. Relatively high operating costs caused primarily by operation of medium recycle equipment and loss of medium.

Jan 1, 1991

By Charles G. Frush

The function of the mine surveyor is to (a) provide a network of points of accurately known position, covering the entire mine property, (b) obtain the required data for the preparation of useful maps and sections! (c) provide position and directional control for the guidance of the operations, (d) measure the progress of the work, (e) measure the movement of rock masses, and (f) make miscellaneous surveys as needed. Mining properties range from the very small to the extremely large, and from those which involve only surface operations to those involving extensive underground workings. Active mines undergo constant change, necessitating continual updating of the surveys. The differences in the character of the deposits, the scale of mining and the mining methods result in large differences in the surveyor's activities and techniques, but many of the problems involved are common to most mines. The surface work of the mine surveyor is very similar to that, of the plane surveyor in that control points are established by triangulation, trilateration and traversing. Detail is taken by direct measurement, by stadia and by aerial photography. The equipment used, the techniques and the methods of processing the resulting data are likewise very similar. However, the underground work is quite different : A. The lines of sight frequently must be carried through constricted openings, often involving short lines of sight and awkward setups. B. The lighting often is poor, requiring illumination of the backsights and foresights, and the crosshairs. C. The ambient conditions often are difficult, involving falling water, high tem- peratures, poor visibi 'kv and heavy traffic through the area being suneyed. D. The surrounding rock map be unstable, resulting in movement or loss of the surveying stations, as well as hazard to the surveyors. E. The points to be measured often are difficult or impossible to reach. F. Steep vertical sights often are necessary, requiring the use of special equipment. G. Many working levels commonly are involved, requiring the transfer of position and orientation to each with a high level of precision. This section therefore will concentrate on surveying problems peculiar to the mine surveyor, chiefly underground work. 22.1-THE MINE COORDINATE SYSTEM A system of coordinates is essential for all permanent mining operations It is very desirable that all mining operations in a ,given area b~ tied into the same system, as this minimizes problems of boundaries and connections Whenever possible this system should be tied into and made part of the state or regional grid system. It is desirable to orient the coordinate grid on a true-north line and to position the origin of the coordinates so that all of the work will be in the "northeast" quadrant, making the north and east coordinates always positive. This can be done by subtracting suitable constant values from the north and east coordinates of the regional system The residual values are of more convenient magnitude and can be used as the local mine coordinates. If the long axis of the mineralization is not generally north-south or east-west.

Jan 1, 1973

By B. T. Stanley

Traditional methods of creating a water tight shaft liner involve the use of segmented or welded steel. When shafts are located in ground that exhibits extremely difficult conditions of high water inflow and hydraulic pressure, composite liners are often combined with ground freezing during construction. The authors were searching for a cost effective and more flexible solution to hydrostatic liners design than the traditional concrete/steel composite design used so far. Searching through new technologies developed for tunneling applications, sprayed on membranes systems seemed very promising but were not developed for the specific circumstances encountered in shaft sinking applications where ground freezing is involved. Even though freezing is a very effective technique, it creates adverse temperature conditions for the application of spray on membranes. In addition, application and hydrating cure times for those membranes products ranged between six to twenty-four hours under ideal conditions (usually temperatures well above freezing point), which eliminated them from consideration in a shaft sinking cycle. While researching different spray on membrane materials, it was discovered that Stirling Lloyd Polychem Ltd. has developed and proven a different membrane material for waterproofing liners in different tunneling applications. The characteristics of the membrane exceeds the pressure parameters encountered in frozen shaft sinking operations, and the chemical cure times were reduced to one hour per layer which worked well into the shaft sinking cycle times. More over their system included a quality control procedure that allowed insuring integrity of the membrane at application time, a very desirable feature for shaft liner construction. However, the frozen rock surface still presented an unknown in the cure time and stability equation. As all membrane products a shotcrete substrate is usually required prior to application. The hypothesis used by the author was to use this shotcrete layer, not only as a substrate, but also as a thermal insulation against the frozen rock and the membrane during both application and curing time. The authors knew from experience that shotcrete could be applied successfully over frozen rock. But the shotcrete temperature curve over time was unknown and no information were found in the available literature. Testing was required to determine whether a suitable mix of shotcrete could be applied to the frozen shaft wall to provide enough heat of hydration for a suitable period of time to create conditions suitable for membrane application and curing.

Jan 1, 2012

By Jesus M. Rohena

Concrete pipes and small boxes have been installed by the jacking method. This paper will describe a recent project were large concrete boxes were installed by the jacking method. This project is in the city of Boston, MA. By now everyone in the USA knows something about this project. The project official name is The Central Artery/Tunnel Project (CA/T). This is the biggest public work project in the USA right now, with an estimated construction cost of 14 billions. The main objective of the CA/T project is to replace an existing artery built in the 1950s to increase capacity and safety. One section of the new artery will cross under several railroad tracks near the South Station. To construct the section of the new artery under these tracks, big concrete boxes were installed by the jacking method. The jacking method can be used to install pipes, small concrete boxes, and the CA/T project has demonstrated that big concrete road tunnel boxes can be installed by jacking.

Jan 1, 2003

By James R. Hindman

Vermiculite is the mineralogical name generally applied to a group of hydrated, trioctahedral ferromagnesian aluminum platty or micaceous silicate minerals. In microscopic particles the mineral as mineral is differentiated from montmorillonite by a higher Si:AI ratio of approximately 3:l and a higher layer charge and higher cation exchange capacities. Commercial vermiculite, the vermiculite which is mined, beneficiated, and discussed in this chapter, is an important industrial mineral which is formed by the alteration of macroscopic particles of biotite and iron-bearing phlogopite. In natural form it has the size and shape of mica, while possessing the ion exchangeable properties of zeolites and some clays. Within the internal structure of vermiculite lie water molecules, which when rapidly heated to high temperature, transform into steam causing the vermiculite particles to increase in volume. This process of thermal exfoliation produces a lightweight product which finds use in various construction products, agriculture, horticulture, and other industrial applications. In exfoliated form it has the low density and biological inertness of expanded perlite, while maintaining a chemically active surface. Most of the uses of vermiculite are for the thermally exfoliated material. In addition, the cation exchange potential of vermiculite and its layer-silicate structure are properties which can be used as the basis for numerous products including intumescent coatings and gaskets, inorganic films, and the treatment of nuclear and other toxic waste. When chemically and physically modified, it possesses some properties common to organoclays and synthetic compounds. In high purity concentrates and manufactured products, these properties can be altered and optimized in applications to produce superior performance. GEOLOGY Mineralogy Vermiculite was first described as a mineral by Thomas H. Webb in 1824. Webb believed vermiculite to be a variety of talc and described its diagnostic property of thermal exfoliation thusly: "If subjected to the flame of a blowpipe, or that of a common lamp, it expands and shoots out into a variety of fanciful forms, resembling most generally small worms having the vermicular motion exact." Observing that with one exception, all commercial vermiculite has formed by the alteration of iron-bearing phlogopite, a simple definition of vermiculite might be the alteration product of trioctahedral micas, macroscopic particles of which display marked exfoliation when heated rapidly to temperatures above 374°C (the critical temperature of water). The first vermiculite described was found near Worcester, MA, but it was later pointed out by Brush (1866) that vermiculite had been known for some time in Japan as a children's novelty. Because the techniques for mineral analysis were somewhat primitive com- pared to those routinely available today, and because the structure and crystal chemistry of the micas and related minerals were not widely understood, the early literature generated at least 20 "new" minerals which were nothing more than variations in the color and chemistry displayed by vermiculite. Trade names such as Dugarlite, Mandolitem, Strong-LiteTM, and Zonolitem are sometimes used to denote commercial vermiculite, thermally exfoliated vermiculite and their products. Vermiculite particles resemble mica and vary in color from colorless through tan and green to black, depending on the chemical composition. Most physical and optical properties are close to those of biotite, with perfect basal cleavage, hardness between 1.5 and 2.5 Mohs, and specific gravity between 2.2 to 2.8. Fine-sized particles will feel talcose, especially when wet. However, for commercial vermiculite the diagnostic test is that of thermal exfoliation. Vermiculite can display a wide range of compositions, depending on the composition of the original mica and the change of chemistry during weathering and ion exchange. Chemical data for some commercial vermiculites are given in [Table 1]. There are numerous analyses for vermiculite given in the literature, and the analyses of vermiculites from commercial deposits will fall within the range indicated by the average analysis in the table. Many analyses separate the adsorbed water (H2OP) from crystalline water and water as hydroxyl (H20+). The basis of separation of adsorbed water is generally considered to be 100°C. However, hydrate water within the vermiculite interlayer begins to be lost at 75°C and lower. Therefore, measured water content and loss on ignition are combined in the table as H20[total].

Jan 1, 1994

By J. I. Schoenherr, G. Schubert, T. A. Baloun

The currently known and used plastics and rubber recycling or sorting processes cannot be applied efficiently and economically due to large amounts and different numbers of plastics types as well as of fine bulky materials (<4mm). These wastes are mostly given to land-fill sites. Thermal adhesion seems to be a great means to efficiently separate plastics mixes. Tests carried out at a special lab-scale testing unit (TaA1) confirm the effectiveness and feasibility of the separating mechanism. The thermal properties of the individual types of plastics differ from each other to a sufficient degree so that special products or product mixes of high material purity can be obtained according to the respective requirements. For this reason, plastics mixes such as PE and PP can be sorted with very good results. The separation efficiency is influenced only by different contact surfaces. The contact period can be adjusted to a short period of time so that sorting large amounts of fine dispersed plastics seems feasible. Sorting processes in feed streams were shown to be technologically effective when applying appropriate technologies. For the time being, the technological application of a thermal adhesion drum separator (TaTr1) is suitable. First tests on such a pilot-scale unit provided good separation results.

Jan 1, 2004