Search Documents

By Peng Gao

Coal-based reduction followed by magnetic separation is an innovative technology used in processing refractory iron ores. Given that size is essential to the separation of the metallic iron from the gangue, the morphology of metallic iron particles and their evolution during coal-based reduction are investigated in the present work. The size of the metallic iron particle increased from 128.76 µm to 565.70 µm when the reduction time increased from 20 min to 60 min at 1,225° C and C/O (i.e., the amount of coal addition in terms of the gram-atomic ratio of the fixed carbon in the coal added to the combined oxygen in iron oxides) of 2.5. Based on our microstructural and metallographic analysis, the iron ore reduction process can be divided into three stages: (1) metallic iron particle formation, (2) iron oxide reduction and metallic iron assembly and (3) metallic iron particle growth. Almost all iron oxides are reduced to metallic iron in the second stage. These newborn metallic iron particles are energetically active and able to assemble and grow, and are eventually separated from the gangue. The large metallic iron particles benefit the subsequent magnetic separation process.

By H. Sevim

The utilization of high sulfur Illinois coal by utility plants has been decreasing since the enactment of 1990 Clean Coal Air Act Amendment. Illinois coal producers can make their coal saleable by offering the choice of taking the combustion by-products from the utility plants and placing them in the abandoned sections of their mines. To be competitive, however, coal producers need to select an environmentally acceptable transportation-handling-placement system through which the cost-per-ton of by-product disposed can be minimized. In this paper, a few such systems are presented. The favorable operating range of each system is determined in terms of distance and tonnage. A case study is given whereby cost analysis is conducted for an underground coal mine receiving by-products from two Illinois utility plants.

Jan 1, 1997

By Michael Hood

Subsidence profiles above two adjacent panels in Illinois are compared with pro- files predicting subsidence behavior obtained using the (i) National Coal Board (NCB, 1975) method, (ii) the profile function method and (iii) the influence function method. The NCB method predicts the maximum subsidence values at the center of the troughs accurately, but, the overall shapes of these predicted profiles do not match the profiles from the measured data well. Consistent values for the angles of draw were measured but these angles were different in the transverse (average value 43 degrees) and in the longitudinal (average value 17.5 degrees) directions. Time dependent subsidence effects are shown to be small but measurable. These displacements continue at a linear rate for at least a 12 month period. A comparison of measured horizontal distances, interpreted as horizontal strain, and the NCB predictions for strain shows that the peak measured strains are greater by a factor f about four than the predicted strains. The relationship between surface curvature and strain is investigated. Problems associated with calculation of surface curvatures from vertical displacement data are highlighted and a recommendation is made for future studies to consider direct measurement of this parameter. Surface curvatures above a moving face are found to be about three times less than the curvatures at the stationary end of the panel. On the other hand, a hyperbolic tangent profile function is shown to serve as an accurate predictive tool for subsidence behavior in two adjacent longwall panels at Old Ben Number 24 mine in Illinois. This function predicts not only the vertical displacements but also the surface curvatures above both panels. Influence functions are shown to be more problematic, although potentially more flexible, in their application than the profile functions.

Jan 1, 1982

By Bauer, Steve, Colin Goodwin, Gerald, Randy Dempsey, Courtland

"The City of Ottawa’s Combined Sewage Storage Tunnel consists of two interconnected tunnels totaling 6.2 km with a diameter of 3m including access shafts and hydraulic structures which connect to the City’s most critical sewers. This tunnel will be built 15m to 30m below ground in the downtown core adjacent to, and crossing below, the Light Rail Tunnel, which introduces additional considerations in terms of sequencing and risk mitigation. The City embarked on a unique Procurement Process to address the risks involved with a large tunnel project and those associated with tunneling below downtown, underneath and adjacent to UNESCO World Heritage Sites, and connecting to live critical sewers. This paper describes the unique procurement approach employed and the contractual risk mitigation measures developed to provide the best value while minimizing risk. Specific features include Market Sounding, using a Fairness Commissioner, Contractor Prequalification and Risk Mitigation Measures in the Tender documents. INTRODUCTION This paper describes how the City of Ottawa (the City) and the project design team developed a strategic Procurement Process and Tender that incorporated industry best practices for technical and contractual risk management for the Combined Sewage Storage Tunnel (CSST) project. The process was unique in that, while it employed a systematic review of project risks, it also solicited input from industry, stakeholders and provincial and federal partners to develop the request for Tender for this traditional design-bid-build project. Key drivers for this approach were initiated from the City’s concerns for cost control, cost certainty and overall project risk mitigation. To address these concerns, the City implemented the risk review and mitigation process right from the project design team selection. It was critical that the project design team embraced this risk management philosophy and carried it through each phase of the project. This paper serves as an excellent resource for municipalities or other owners embarking on a similar tunnel project, on how to properly apply industry best practices and the benefits of using them."

Jan 1, 2016

By Sidney A. Suhler

The persistent requirement for methods and equipment capable of detecting hazardous anomalies in advance of underground mining has led to the development by the U.S. Bureau of Mines of a directional radar probe. The probe operates from boreholes drilled from the surface into the underground region to be mined. The engineering model radar was completed in early 1982 and field demonstration tests were performed in May of that year at a selected coal mine. Preliminary in-situ electromagnetic tests were performed at several candidate coal mines to evaluate the radio-frequency characteristics of the coal. A coal mine in New Mexico was selected on the basis of low EM propagation losses in the coal and the presence of an extensive coal seam displacing fault as a radar target. The borehole radar was operated in two vertical boreholes which intersected the coal seam at approximately 25 and 40 feet from the fault interface. Radar reflections from the coal/ rock interface were detected in both tests. Underground tests in a horizontal borehole in the coal were less successful because of interfering reflections. Additional borehole-to-borehole tests were performed with a separate ground penetrating electromagnetic system to obtain radar range calibration data. The coal was found to be bounded by very lossy roof and floor sandstone and shale while propagation through the coal seam was obtained at distances up to 175 feet between test boreholes. Coal seam continuity was indicated by the hole-to-hole experiments through a section of the seam previously thought to be completely cut off by the fault.

Jan 1, 1983

The last time Mining Engineering presented an issue with a special focus on Canadian Mining (ME, August 2008 pp. 28 to 40) things were going well. A feature story took a look at Xstrata?s Nickel Rim South Mine in Sudbury and the booming Canadian oil sands were discussed at length. Potash prices were soaring, large diamonds were being found and British Columbia was launching plans to find more workers. How things have changed in six short months. What began as a mortgage crisis grew into a credit crisis, then mutated into a financial crisis, that has taken its toll on the value of bonds, loans, stocks, real estate and commodities. Miners that were flying high on unprecedented commodity prices six months ago have begun scaling back with delays, shut downs and layoffs as they struggle to survive this most recent economic downturn.

Jan 1, 2009

By S. C. O?Brien

This paper develops the procedure for simulating the special locked-cycle Work Index laboratory test using the kinetic parameters obtained by conducting standard size-mass balance (SMB) grinding tests and presents the results for three materials - quartz, a taconite iron ore and a bituminous coal. It was found that the WI could be determined by simulation; however, if a material breaks abnormally, a full description of its abnormal breakage is necessary. It was also found that the sensitivity of the WI test procedure to the sieving process and the estimating of the 80% passing size of the sieve undersize is sufficient to question the practice of quoting a WI to two or more decimal places. Finally, if a material grinds abnormally in the Work Index mill, then the WI test should not be conducted.

Jan 1, 1987

By L. Harris

The gold mining and ore processing operations of Minera Yanacocha S.A. are 10cated in an area 4,000 meters above sea level in the Peruvian Andes same 600 km north of Lima and 20 km north of Cajamarca. The joint venture partners are Newmont Second Capital (USA); Compania Minera Condesa (Peril); Mine Or (France) and the IFC. Newmont manages the operation. The Yanacocha district comprises several areas with mineralization evidence. The first ore with minable reserves of 28 million tonnes of ore assaying about 1.4 gpt Au is called Carachugo and is being mined and treated at the rate of 14,000 tonnes of ore per day by open pit mining methods. ROM ore is dump leached and the gold recovered in a Merrill Crowe plant. The plant design incorporates some unusual considerations to overcome the problems of the high rainfall in this area and assure the protection of the environment.

Jan 1, 1994

By D. M. Neil

Road-headers are one of the most popular mechanized excavators used in mining and civil under-ground construction. These machines are primarily used in soft to medium hard rocks. This paper reviews the parameters associated with the application and operation of road-headers and presents a method for estimating cutting performance.

Jan 1, 1994

By J. A. Herbst, H. R. Cooper, R. J. Brison, R. W. Harper, K. P. Ananthapadmanabhan, W. C. Hellyer, B. H. Bergstorm, D. M. Hopstock, H. Rush Spedden, W. C. Hellyner

Scope of Section The physical characterization of an ore or mineral mixture in such detail that mineral processing may be effectively applied to create more useful products is one part of the technology of sampling and testing. In addition, the evaluation of the multitude of separation processes, both physical and chemical, combined with ancillary opera¬tions and performed on samples at a laboratory scale, is another part of the testing procedure. Although analytical techniques provid¬ing quantitative determinations of elemental compositions are an im¬portant and necessary supplement to any testing program, that field of endeavor is a well-developed, separate entity beyond the scope of this Section. Sampling procedures cover the practice of selecting representative quantities of test materials in the field to evaluate mineral deposits, and extend to techniques of obtaining process samples in slurry and bulk ore as part of process evaluation. The same techniques are appli¬cable, of course, to standardized methods of metallurgical accounting. Sampling is also an important facet of successful on-line measurement of slurry properties such as assays and particle size in the practice of automation. However, the sampling methods in this case can be different from those needed for precise testing and accounting pur¬poses. Sampling was well defined in Taggart's Handbook as "the opera¬tion of removing a part convenient in size for testing, from a whole which is of much greater bulk, in such a way that the proportion and distribution of the quality to be tested (e.g., specific gravity, metal content, recoverability) are the same in both the whole and the part removed (SAMPLE). The conditions of the more stringent definition, that the sample shall be completely representative of the whole as regards all aspects save bulk, are practically never fulfilled when heterogenous mineral mixtures are sampled." Taggart's Handbook of Mineral Dressing, Section 19, "Sampling and Testing," continues to be a very useful compendium of principles and techniques, particularly as applied to manual methods for han¬dling samples. In the intervening years since its last revision, substan¬tial progress has been made in both the theory and the techniques; thus, this current contribution is designed to be an extension of the earlier work, yet complete enough to provide procedural guidelines to methods of continuing validity. Although basic principles of testing remain unchanged, the meth¬ods of applying those principles have undergone great change. New testing equipment has become available, yielding a greater precision of results. Testing methods have been refined which, in many cases, allows for a valid scale up of flowsheet designs without the necessity of costly pilot or prototype plant development. Justification for a Sampling and Testing Program* The proper evaluation of a mineral property is a complicated process. It often is done on a team basis with the exploration geologist, mining engineer, mineral process engineer (extractive metallurgist), economist, and product utilizer (ceramist, chemical engineer, chemist, metallurgist, etc.) all represented. The mineral processing engineer is a key member because he can provide a go no-go answer to the question, "Can this ore be processed economically?" In addition, his judgment on the response of even the initial sample to processing can be an invaluable guide to the proposed process and its mutations. Since the capital investment and operating costs are so sensitive to the type of process used, the judgment of the mineral processing engineer forms an important part of the early evaluation of the profitability of a new mining venture. This early estimation of the processing approach is all the more important since, for some metalliferous ores, the capital investment for mill, smelter, water supply, and tailings disposal exceeds the cost of the mine. At present, for commodities such as coal, the reverse is true. There is a smaller capital investment for the coal preparation plant than for the mine. In general, both the capital and operating costs escalate very rapidly in the following order: gravity concentration of alluvial deposits (e.g., dredging), gravity concentration of lode ores, flotation, simple hydrometallurgical processes, and complicated hydrometallurgical and pyrometallurgical processes. The latter two processes may cost 100 to 1,000 times more per ton treated than processing of a simple alluvial deposit. This dictates that the valuable mineral be concentrated as much as possible to minimize the total tonnage treated in the more expensive operations. Within each of these ore-processing categories there is a wide range of process sophistication and hence of capital and operating costs. Perhaps the greatest variations are in the chemical processing of ores. These range from the simple leaching of a copper waste dump to very sophisticated hydrometallurgical processing of ores in increasing order of cost. Because the overall cost of a mining venture is so sensitive to the process selected, it is essential that the mineral¬ processing engineer evaluate the ore in the initial stages of the development of an ore body. As better samples become available, he must continually revise his estimate of the process to be employed. The sampling and testing process must be a necessary and continuing activity throughout the life of a project. One fundamental aspect of nearly all mineral deposits is the inherent variability of the mineral assemblage and composition. A utopian goal of any processing plant is to have the process so flexible and so well-defined that an automatic process control system can optimize the economic recovery at all times. Since this is rarely possible, a continuing or at least a periodic testing program is desirable. Variables to be considered are: 1) Ore body inconsistencies. 2) Zonal variations. 3) Feed variations from mining plan or methods. 4) Variable performance of processing units due to wear. 5) Seasonal or other changes affecting processing conditions such as water quality, temperature, etc. 6) Changing market conditions for product quality or byproducts. 7) Technological advances in processing methods or equipment. 8) Increasing demands for environmental control. 9) Changing economics of competitive processes, of supplies, of capital investment vs. labor costs, etc. Sampling Procedures Preliminary Guidelines for Sampling Ore Deposit Studies. t At a very early stage, it is essential that the mineral processing engineer receive a sample of the ore. This may be a portion of the diamond drill core or a split from the trench, pit, churn drill, channel, or sheet sample. Even a grab sample may have some value, but it should be selected by the mining engineer or exploration geologist to be as representative of the ore body as possible within his best judgment. The sample delivered to the process engineer should have been subjected to as little prior crushing as is practical since fine sizes are difficult to concentrate. In addition, finely ground ores are readily oxidized and thus may give misleading test results. Furthermore, ground samples may make it impossible to eval¬uate either the comminution or the coarse-gravity concentration pro¬cesses. For an initial evaluation, a good deal may often be learned from a sample of only a few pounds if that is all that is available. To obtain the maximum information from a sample, its selection should be carefully discussed with the mineral processing engineer. In addi¬tion to being as representative as possible, the mineralogically distinct samples should be carefully segregated rather than composited. Since drastically different processes are often needed to process samples of differing mineralogy, considerable care and time must be exercised during this sample collection step. The segregation of samples showing gross mineralogical differences, such as the oxide caping on a sulfide deposit or a laterized zone, is easy. It is the more subtle changes in mineralogy that can often elude the field man. Yet these differences are often sufficient to dictate that an entirely different type of process be used. Obviously, the selection of these initial samples for ore testing and mineralogical studies requires that it be done by a man of consider¬able experience and judgment. While the mining engineer or field geologist is collecting these samples, he should also note and convey to the processing engineer such details as water quality and availabil¬ity, terrain, potential mill location, tailings-disposal areas, case of transportation, etc. As the property is developed with additional drill holes, adits, etc., larger and more representative samples will be required to develop the ore-processing flowsheet more adequately. If pilot-plant studies are required, a very large sample may be necessary. Though the type and amount of sample collected for flowsheet development investigations vary widely, gathering a representative sample of the ore body is a prime requisite for any process development effort. The process developed for any given ore body is only as reliable as the sample on which the flowsheet was based¬

Jan 1, 1985

By John A. L. Campbell

Surface dependent processes, such as froth flotation and flocculation, are important or potentially important techniques for combating some of the current major problems in coal preparation. In order to correctly apply or imporve a surface dependent process, it is of paramount importance to understand the interfacial phenomenon, especially the double layer properties, exhibited by the solid. The specific objective of this research was to determine the properties of the bituminous coal/liquid interface by an electrokinetic method, streaming potential, and to relate the findings, wherever possible, to the existing unit operations of froth flotation and flocculation. The electrokinetic properties of both the whole coal and its lithotypes were investigated. As part of the total investigation, the role played in the double layer by the reagents commonly employed in the surface dependent process was also established (1). These data will be presented at a latter date.

Jan 1, 1969

By A. Dell’Era, E. Ciro, C. Lupi

The indium recovery via electrowinning from sulfate baths has recently gained significant attention as it does not present toxic emissions, hermetically sealed system requirements, human health, and environmental hazards. Following previous works related to the optimization process for AISI 316L and Ni cathode, it was observed significant importance of the metal supports on the input and output parameters of the indium electrowinning process from sulfate solutions. Thus, comparing input and output parameters in both cases seems very interesting. Particularly, regarding the input parameters, the attention has been focused on the electrolyte composition, current density, and temperature, while productivity, morphology, and structure have been considered regarding the output parameters. Considering the productivity as the optimal output, the findings for Ni cathode were better than that for AISI 316L in most of the selected conditions studied. In the case of morphology, indium grains appear rounded and dendritic on the AISI 316L, while those on the Ni cathode show stratified lamellar grains. Anyway, the indium deposit obtained on Ni cathode shows bigger grains independently from the used operative conditions with respect to that on AISI 316L. Regarding the structure, it is clearly tetragonal, but preferential orientation, crystallinity, and deformation of the structure strongly depend on the metal support.

Jun 14, 2023

By Xianyang Qiu, Xiuzhi Shi, Chen Xie, Xiaofeng Huo, Yanhai Wang

In upwards medium-deep hole cut blasting, many confinement effects exist due to the small number of free surfaces, which is mainly provided by an empty hole. If the cut blasting effect cannot meet expectations, then subsequent blasting construction will be seriously affected, and large security risks to operators in the stope can be induced. The number of free surfaces is directly related to the layout of the cutting borehole. Therefore, it is necessary to optimize the layout of the first round of cutting boreholes. Theoretical analysis, numerical simulations, and field tests were used to study the formation process of cut blasting and optimize the layout of the first round of cutting boreholes. Based on the blasting parameters in the field, LSDYNA software was used to establish cut blasting models with four kinds of borehole layouts in the first round. The RHT constitutive model was used to simulate the rock-breaking effect. The numerical results show that the cut blasting effect is optimal when Nos. 3, 5, 7, and 9 are charge holes and Nos. 1, 2, 4, 6, and 8 are empty holes. In addition, the greater the number of empty holes, the larger the release space and the better the cut blasting effect. The uniformity of the empty hole distribution, namely, the uniformity of the release space, also affects the cut blasting effect. The field results indicate that a good cut blasting effect can be achieved by optimizing the borehole layout.

Sep 7, 2023

By P. Zhang, S. Al-Thyabat

"Phosphate rock contains traces of rare earth elements (REEs) and can be a secondary source of these critical materials as large tonnages of phosphate rock are mined annually. Attention has mostly focused on the extraction of REEs from phosphogypsum, which contains more than 70 percent of the REEs reporting to phosphate concentrate, with only limited work conducted on REE extraction from sand tailings and slime even though they account for 16 percent and 15 percent, respectively, of REEs mined with phosphate matrix.In this work, phosphate flotation tailings were upgraded by gravity separation and froth flotation. Gravity separation was conducted using a laboratory shaking table, while flotation was conducted in a Denver D-12 flotation cell. The concentrated tailings were then leached by nitric acid followed by REE extraction with solvent and ion-exchange resin.The sand tailings were assayed as having 2.6 percent phosphate (P2O5 ) and 198.1 µg/g REEs. It was found that the shaking table could produce tailing concentrate assayed as having 8.6 percent P2O5 and 616 µg/g REEs but with only 20 percent REE recovery, while the froth flotation produced froth concentrate assayed as having 8.1 percent P2O5 and 368.2 µg/g REEs with 63.5 percent REE recovery. Leaching the flotation concentrate with 5.2 M (25 percent) nitric acid followed by extraction with solvent and ion-exchange resin yielded precipitates with REE contents of 0.926 and 0.314 percent, respectively, compared with 0.716 and 0.213 percent when table concentrate was used.IntroductionRare earth elements (REEs) consist of a group of 17 elements: the 15 lanthanides along with yttrium (Y) and scandium (Sc). They are rare not because of their scarcity in the Earth’s crust but because they are rarely found in economic and mineable deposits. REEs are called “seeds of technology” because of their importance to some critical technological industries such as renewable energy, hybrid cars, electronics and batteries. On average, an electric car or a hybrid car contains about 10 kg of REEs (Grasso, 2012; Radhika et al., 2011).REEs are usually categorized into light (LREE) and heavy (HREE). LREEs consist of lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pr), samarium (Sm), europium (Eu), gadolinium (Gd) and scandium (Sc), while HREEs consist of terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), lutetium (Lu) and yttrium (Y). About 200 minerals contain traces of REEs, but only three are considered economically significant: bastnasite, with the formula La,Ce(CO3)F; monazite, with the formula(Ce,La,Nd,Th)PO4; and xenotime, with the formulaYPO4 (Jordens, Cheng and Waters, 2013)."

Jan 1, 2016

By William M. Gray

[The products of mites hive historically beet a very large and important segment of total shipment transported by American Railroads. Much as the Mining transportation Executives right have wished for coal and other mineral deposits to be found along navigable rivers, where railroads have for years been competing with the very aggressive Army Corps of Engineers and the inland waterway operators, the mineable reserves are more often that not located in the arid west far from these "free" waterways. The rivers cannot go to the mines but the railroads could, did, and continue to invest it new lines to reach new mines. The mining industry and the railroad industry have good reason to rely upon each other. The former Northern Pacific Railway, the Great Northern Railway, the Chicago, Burlington and Quincy Railroad and the Spokane, Portland and Seattle Railway merged in 1970 to form the Burlington Northern Railroad, with Lou Menk as its first President. As unofficial spokesman for the industry, be had, for years, conducted a tireless effort to educate shippers, lawmakers and the general public of the single most critical problem confronting the railroad industry, the strangle bold of government regulator.]

Jan 1, 1985

By R. S. Olson

The operation of a series wash thickener-two stage filtration circuit determines the soluble loss in many hydrometallurgical operations A study of this circuit yielded expressions which permit calculation of soluble loss for almost any condition of operation. The soluble loss over a range of the circuit variables is presented to illustrate and evaluate circuit performance, The interrelation of factors affecting filter performance and some of the wash circuit, variables are quantatively described. Filter wash, which is governed by wash zone size, filter pulp level and filter feed pulp density, has the greatest affect on soluble loss. Excepting clothing blinding and flocculation the factors which decrease filter capacity also decrease soluble loss. Repulping with water, under some circumstances, can bean important means of soluble loss reduction. Water for primary filter wash, leach pulp density repulp density and wash thickener underflow density have little effect on soluble loss. The dilution of both o the filter pulps with wash solutions is suggested as a means of reducing soluble loss, and at the same, time, controlling the performance of the filters. Blowback and filter cloth blinding seriously increase soluble loss.

Jan 1, 1962

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence induced by underground coal mining activities, especially longwall mining operations, can cause various problems to interstate highways ranging from structural integrity, drivability to safety. Accurate subsidence prediction, correct influence assessments, and effective mitigation measures are the keys to ensure the safety of highway traffic. The surface subsidence prediction program, called comprehensive and integrated subsidence prediction model (CISPM), was developed based on the principle of influence function method and has been validated with a large number of subsidence measurements. In this paper, the techniques to use the predicted final surface movements and deformations for assessing their influence on the integrity and functionality of highway structures (e.g., road surface pavements, concrete slabs, transverse joints, etc.), vehicle dynamics, comfort level, and drivability are presented. A number of mitigation measures to protect the highway structures and to ensure traffic safety are proposed along with an application case.

The Iron Ore Company of Canada (IOC) is the largest manufacturer of iron ore pellets in Canada and its customer base covers North American, European and Asian steel producers. The company operates a mine, concentrator and a pelletizing plant in Labrador City, Newfoundland and Labrador, as well as port facilities located in Sept-Iles, Quebec. It also operates a 418-km (260-mile) railroad that links the mine to the port. IOC has approximately 1,900 employees. Its shareholders are Mitsubishi Corp. (26.18 percent), Labrador Iron Ore Royalty Income Fund (15.1 percent) and the international mining group Rio Tinto, which is its major shareholder (58.72 percent) and operator, with activities in more than 40 countries throughout the world. The IOC was incorporated in 1949 and by 1954 it had completed the Quebec North Shore and Labrador (QNS&L) rail line. IOC began mining in Schefferville, Quebec by 1954 and closed those operations down in 1982. In 1962, IOC commissioned the present day Carol Project consisting of mining, concentration and pelletizing facilities in Labrador City, Newfoundland. In 2004, IOC shipped its one-billionth tonne of ore on the QNS&L Railway. In 2005, IOC celebrated 50 years of mining history. The company expressed an interest in reducing the amount of oversize material (>1 m x 1 m x 1 m or 3.2 ft x 3.2 ft x 3.2 ft) being produced and its subsequent downstream effects, including in-pit sorting and reduction, damage to mobile equipment and significant delays in the loading pockets and the primary crushers. To achieve this goal, an oversize reduction project was undertaken by the mine that, to date, has significantly improved upon baseline measures. One key approach used to reduce the amount of oversize was the implementation of thicker emulsion. The introduction of a thicker emulsion provided more resistance to the forces created by dynamic water and reduced the infiltration of the emulsion into the cracks and fissures of the rockmass, resulting in reduced amounts of oversize and more consistent fragmentation throughout the muckpiles. Additionally, a significant reduction in nitrates leached into the mine water discharge has been realized. To determine the effectiveness of the oversize reduction project, IOC used a first-of-kind technology to assess fragmentation presented to the shovel at the digging face. A digital vision system (DVS) was installed on one of the shovels to capture images that were stamped with GPS locations. A large population of digital images were analyzed to produce a robust fragmentation distribution baseline that was used as one of the mine key performance indicators (KPI). Changes to blasting practice were subsequently measured against the baseline KPI to assess effectiveness.

Jan 1, 2011

By William Gleason

The mining industry is under immense pressure to not only meet increasing demand for minerals, but to do so in an environmentally safe and sustainable manner. Growth in electric vehicles, battery storage, renewable energy infrastructure and data centers to power artificial intelligence (AI) has led to an unprecedented demand for minerals such as copper, lithium, rare earth elements and others. The need for these minerals for national defense has only increased the pressure on the mining industry. Increased geopolitical tensions between the United States, China and Russia has added a sense of urgency as supply chains have become a focal point for the U.S. Department of Energy (DOE) and Defense (DOD) and other government agencies. The International Energy Agency (IEA) predicts that copper demand is expected to grow by 50 percent by 2040 while demand for lithium could increase eight-fold by 2040 and demand for nickel and cobalt could double. The challenges to meet the increased demand include technological, workforce, exploration and environmental issues. From Feb. 22-26, the global mining industry will converge on Salt Lake City, UT for the MINEXCHANGE 2026 SME Annual Conference & Expo where these challenges and others will be addressed by some of the leading minds in the industry. Included in this year’s conference is the Resilient Energy in Mining Symposium, a symposium with input from across SME that looks to address some of the most significant challenges the industry is facing. “Adopting environmental, social and governance (ESG) best practices has become a necessity for the mining industry, not an option. The Resilient Energy in Mining Symposium is crucial for MINEXCHANGE 2026 because it addresses the complex challenges of transforming traditional mining operations to support a sustainable and secure energy future,” Lisa Gonzales, principal engineering at Arcadias and MINEXCHANGE 2026 SME Annual Conference Chair and chair of the Resilient Energy in Mining Symposium said. “Mining is inherently energy-intensive, yet it is also foundational to the global energy transition, supplying the critical minerals needed for renewable technologies. By bringing together industry leaders, the symposium fosters collaboration and actionable change, showcasing advancements and real-world solutions that demonstrate the tangible benefits of resilient energy strategies. This unique forum enables knowledge sharing, inspires innovative thinking, and helps set the standard for sustainable practices across the sector.” The symposium was created in direct response to a SME member survey in 2023 conducted by the Responsible Mining and Underground Construction (RMUC) Strategic Committee. “The survey highlighted a strong demand for technical resources on energy transition, carbon reduction, renewable power, climate change, and ESG reporting,” Gonzales said. “To address this, I collaborated with RMUC to engage committee members from all SME Divisions, ensuring a diverse and comprehensive platform that reflects every aspect of mining. We intentionally structured the symposium to centralize key content and minimize duplication across divisions.”

Jan 1, 2026

By D. Parks, A. Miller, M. McNinch, R. Jacksha, H. Nickerson

Each year hundreds of mine workers are involved in machinery-related accidents. Many of these accidents involve inadequate or improper use of lockout/tagout (LOTO) procedures. To mitigate the occurrence of these accidents, new safety methods are needed to monitor access to hazardous areas around operating machinery, improve documentation/monitoring of maintenance that requires shutdown of the machinery, and prevent unexpected startup or movement during machine maintenance activities. The National Institute for Occupational Safety and Health (NIOSH) is currently researching the application of Internet of Things (IoT) technologies to provide intelligent machine monitoring as part of a comprehensive LOTO program. This paper introduces NIOSH’s implementation of an IoT-based intelligent machine monitoring system to improve safety during operation and maintenance at a concrete batch plant. INTRODUCTION Of the hundreds of machinery-related accidents occurring every year in the mining industry, incidents involving stationary machinery at surface mines continue to be amongst the most frequent [1]. A National Institute for Occupational Safety and Health (NIOSH) study showed that the majority of fatal accidents involving stationary machinery at surface mines occurred at sand and gravel (38%) and stone (26%) operations. Of these accidents, entanglement in conveyor components were the most common cause of fatal accidents (48%) [2]. The same study stated that one-third of these accidents involved improper lockout/tagout (LOTO) procedures as a contributing factor. The U.S. Mine Safety and Health Administration (MSHA) acknowledged this problem, stating in a recent request for information (RFI) [3]: “Since 2007, there have been 17 fatalities related to working near or around belt conveyors, of which 76 percent were related to miners becoming entangled in belt drives, belt rollers, and discharge points. Factors that contribute to entanglement hazards include inadequate or missing guards, inadequate or an insufficient number of crossovers in strategic locations, and/or inappropriate lock out/tag out procedures. Systems that can sense a miner's presence in hazardous locations; ensure that machine guards are properly secured in place; and/or ensure machines are properly locked out and tagged out during maintenance would reduce fatalities [3].” In response to this problem, NIOSH’s Spokane Mining Research Division (SMRD) is exploring the potential application of Internet of Things (IoT) technologies to provide cost-effective intelligent machine monitoring systems for improved worker safety [4, 5]. SMRD partnered with Central Pre-mix CRH Company (Central Pre-mix) to develop and install a proof-of-concept wireless IoT solution to monitor machinery and conveyors during operation and maintenance. The primary goals of the system were to provide real-time monitoring of access points and facilitate the planning and execution of LOTO procedures

Jan 1, 2019