Search Documents

Clean Diesels fuel-borne catalyst, Platinum Plus, helps improve fuel economy for all engines up to 10 percent while reducing particulate emissions by up to 25 percent. When used with a simple diesel oxidation catalyst, particulate emissions can be reduced by 30 to 50 percent. The use of Platinum Plus enhances combustion in the cylinder, burning fuel more completely. This reduces CO2 and other greenhouse gases and lowers total operating costs by improving fuel economy.

Jan 1, 2007

Sustainable development is at odds with reality in the minerals industry. Increasing world population and aspirations are leading to increased energy and mineral consumption. Non-renewable fossil fuels are being exploited at a much faster rate than they are being discovered. Mineral reserves are diminishing and of lower grade. Despite recycling, many of the economic reserves of the rarer metals on which technological society has come to depend are being depleted, and many of the bulk metals are being exploited at ever increasing rates. And yet, mining continues, with a long-term downtrend in commodity prices, matched by more efficient mining and processing. Will society turn to a low carbon economy before fossil fuels are depleted? Will prices come to better reflect the full cost of mineral production? Will technology save us, or is it at the root of the problem? The key drivers continue to be an ever increasing aspirational population and the law of supply and demand, rather than sustainability considerations. The paper illustrates this with examples of worldwide and Australian data.

Jan 1, 2011

By Adriaan de Villiers

Many conventional structural analysis and design methods in current use are not appropriate for the mining industry. Two major reasons for this are that: • The economic life of a particular mine is limited, and • Much of the equipment and machinery used by the mining industry operates at relatively low speeds. Both of these factors can have significant cost implications if they are not properly accounted for during plant design. In particular, the often used practice of mitigating excessive vibration by adding mass to machinery supports is not only expensive but may worsen the vibration effects. Some of these problems, such as increased wear and tear, are not always easy to trace back to inappropriate design. This article focuses on vibration related issues and demonstrates that the mining sector has unique problems requiring unique solutions. Vibration: the basics Historic developments leading to current vibration design practices provide the key to why such practices are often inappropriate for the mining industry. To understand this, it is necessary to introduce some basic vibration theory. Consider a simply supported beam or foundation on which a vibrating machine is mounted. For analysis of the system's dynamic response, it may be viewed as a mass attached to a spring and a damper, such as the shock absorber of a car.

Jan 1, 1992

By P. van der Veen

The objective of this paper is to analyze the evolution of the strategic drivers of the mining sec-tor over the last half century, which has been guided by a varying and expanding list of motivations. While companies cannot survive for long unless they are making profits, the strategic drivers of the industry have gone far beyond profits since at least the mid-1970s when environmental concerns began to be taken seriously. For the most part, these forces have followed global trends and public opinion, but they have been shaped and magnified by the significant, often dominant role that the mining sector plays in many economies. While the mining sector used to be primarily motivated by the first pillar of sustainable development -i.e. the economics pillar-, in the 1970s the second environmental pillar became an important factor in decision making, and in the 1990s the third social pillar emerged as a major driver.1 The entrance of new strategic drivers has also had considerable impact on technological and organizational developments in the mining industry; however, technological changes, driven by cost reduction considerations, have in turn impacted the strategic drivers of the industry, resulting in the need for further technological and organizational developments.

Jan 1, 2007

By C. R. Landis

The Wyoming bentonite industry finished 2005 with strong growth. For most of the markets, demand exceeded supply. The industry continues to be heartened by the strength of its longtime markets, oilfield and iron ore pelletizing markets. But overall, all of the major markets enjoyed good to excellent commercial conditions. Growth at the macroscale was fueled by the continued strong domestic economy, by the exchange rate of the U.S. dollar in global markets and by strong worldwide global demand. As result, two new greenfield operations are in the early stage of development in the Wyoming region for the first time in more than two decades.

Jan 1, 2006

By T. R. Ellis

A number of important international events took place in 2001 in the development and evolution of mineral valuation standards internationally. In Canada, the CIMVal Committee released a draft discussion paper for public and industry comment on principles to guide the development of the planned Canadian mineral property valuation standard. The International Accounting Standards Board (IASB) received comments on its Extractive Industries Issues Paper. IASB will decide whether the financial statements of public mining and petroleum companies will be allowed to provide the value of mineral and petroleum assets on a current value basis instead of an historic cost basis. The author led the Extractive Industries Task Force of the International Valuation Standards Committee (IVSC) in developing its submission to IASB. IVSC intends to develop an extractive industries valuation section for its International Valuation Standards, which could support the planned IASB standard. In Australia, AusIMM has carried out an in-depth review of its highly regarded VALMIN Code. The AusIMM's MICA subdivision organized the VALMIN ‘01 Conference in Sydney, Australia, with a range of international and current issues papers published in the VALMIN ‘01 book. Considerable support for the IVSC initiative was evident at this conference. The results of the review of the extractive industries submissions to the IASB are expected to be released in early 2002. The CMMI Congress in Cairns, Australia in May 2002 is likely to prove to be an important forum for continued discussion of the development and implementation of international standards and qualifications for mineral valuation. The outcomes and implications of these events are discussed.

Jan 1, 2002

By P. Amelunxen

This paper presents the authors? personal experiences in the design and operation of moly separation circuits in copper-moly concentrators. Topics discussed include column cells versus mechanical cells; use of nitrogen; use of CO2 and sulfuric acid for pH modification; and general equipment selection and sizing. A benchmarking of main operating parameters for industrial plants is presented. Upgrading curves for commercial column and mechanical cleaning circuits are also presented, showing that with average flotation kinetics and rougher concentrate grades, technical grade concentrates can be easily achieved with five column cells operating in counter-current configuration.

Jan 1, 2009

Remote methane detection State and federal regulations require frequent measurements to verify that safe methane levels are maintained in underground coal mines. Ventilation control is the primary means of maintaining safe methane levels. In the immediate face area, where the highest methane levels occur, methane measurements are required every 20 minutes during active mining. To perform these measurements, temporary roof supports must be erected. This allows a miner to reach the face. There a hand-held methanometer is used to make the measurements. This procedure is time consuming and potentially hazardous. To facilitate the measuring process and reduce the miner's exposure to roof falls, the US Bureau of Mines has developed a prototype optical device. It can measure methane remotely from distances up to 12 m (40 ft). The device uses two infrared signals, reflected from the coal face, rib, or roof. One signal is absorbed by the methane, the other is not. The ratio of the two signals determines the average methane concentration in the face area. The prototype detector has also been successfully tested at the Lake Lynn, PA Laboratory. Instantaneous responses were obtained for methane in the ventilation airflow and for methane layered near the roof. Conventional methanometers required from five to 25 seconds to respond to the methane in the ventilation airflow. They did not respond to methane in the roof layer. For more information about the Bureau of Mines' remote detection research, contact Richard W. Watson, US Bureau of Mines, Pittsburgh Research Center, Box 18070, Cochrans Mill Road, Pittsburgh, PA 15236 or call (412) 892-6630. Ignition suppression system The incidence has increased of fractional spark ignition at the mine face. One reason is the advent of mechanical mining. Another is the more difficult ventilation conditions associated with deeper and more extensive underground workings. To cope with the problem of frictional ignition, the Bureau of Mines initiated research to develop a system that would provide rapid detection of incipient methane-air ignition. Then, rapid dispersion of a quenching agent would ensure that the methane flame was extinguished while it was still relatively small. This concept was successfully demonstrated by suppressing explosions in the Bureau's Bruceton, PA experimental mine. But the bulkiness of the early storage-dispersal system proved impractical to retrofit onto face equipment. In a cooperative effort by the Bureau and the Mine Safety and Health Administration, a more compact system has been developed and is being tested. A continuous mining machine has been equipped with four 1.8-m-long (6-ft-long) and two

Jan 9, 1987

By S. M. Pickering

Banks frequently manage large privately owned mineral land trust accounts for estate heirs. The bank has a fiduciary obligation to follow the “Prudent Man Rule”, which requires that trust properties be managed at least as well as a prudent and knowledgeable owner could. However, banks may not have internal staff proficient at mineral property values, lease contracts, royalties, mining practices, etc. This is an opportunity for experienced geologic consultants and certified minerals appraisers to provide needed help. Items valuable to Trust managers may include: 1. Marketing privately owned mineral trust lands to mining or oil & gas firms, assuring competitive offering prices and terms; 2. Negotiating favorable new mineral lease and purchase-option contracts; 3. Monitoring progress of mining, royalty payments, land reclamation, and environmental clean-up work; 4. Balancing future mining income with later industrial, commercial or housing development, timber harvest, etc.; 5. Assuring that Depletion Allowance tax advantage is taken for actual mine royalty payments, but not for annual non-mining lease (rental) income; 6. Appraising in-ground mineral value for bank audits, estate tax valuations, and equitable property division between heirs; and 7. Serving as expert witness, representing the legal interests of the bank, trusts, and the mineral heirs in litigation. Banks do welcome reliable advice which assists them in achieving the “Prudent Man Rule” and improving mineral income to their land Trust accounts.

Jan 1, 2002

By J. H. Zietsman

Ilmenite smelting furnaces must be operated with a freeze lining of frozen slag to protect sidewall refractories from chemical attack by liquid slag. The process has two main control objectives: Firstly the slag TiO2 content must be controlled according to specification, and secondly a safe freeze lining thickness must be maintained. This text only concerns itself with the second objective. Freeze lining thickness cannot be measured directly due to conditions inside the furnace. It is therefore inferred from signals of thermocouples installed into the furnace sidewall. These signals are used as the 'controlled variables' in the freeze lining thickness control loop. The dynamic characteristics of these signals are the focus of this text. During this study a model of the process was constructed to study interactions between the slag bath and the freeze lining. This model was used to conduct simulation-type experiments to study the influence of various parameters (temperature, slag composition, ilmenite feed rate, reductant feed rate, power input, etc.) on the slag bath, freeze lining, metal bath, furnace wall and other parts of the process. In the case of the furnace wall, the modelling results were first plotted in the form of time-dependent isotherms. The dynamic thermal behavior of the furnace wall became evident from these results. To illustrate the dynamics of sidewall thermocouple signals, the results were also plotted as time lags between events occurring in the slag bath, and the time when a thermocouple registered a temperature change. The events studied included sudden changes in slag bath state (composition and temperature), changes in operating setpoints (ilmenite feed rate, reductant feed rate, power input), and operational errors (complete loss of reductant or of all feed). All of the result sets showed significant lags between occurrences in the slag bath and temperature changes in the refractory wall. The delays are such that it appears impractical to rely on sidewall thermocouple signals for warning of impending damage to the refractory wall, or for purposes of actively controlling freeze lining thickness. Some measures are suggested to improve the usefulness of these signals during furnace operation.

Jan 1, 2005

By D. R. Dolinar

The fall of small pieces of rock between roof bolts causes over 80 pct of the ground fall injuries in underground coal mines. Roof screen, if installed on the bolting cycle, can significantly reduce the number of these injuries. As the surface of the roof fails, the screen will have to retain the broken rock without failing or excessive deformation. Welded wire screen is the most common type of screen material used for roof surface control in underground coal mines. The load-deformation characteristics and the load capacity of welded wire screen were evaluated in the laboratory in a specially built test frame. In the frame, the square screen sections were held in place by bolts and bearing plates at the four corners while a center load was applied to the screen. The parameters evaluated included the wire gauge and configuration, the bearing plate loads and bolt spacing. The wire gauge of the tested screen was 4, 6, 8, 9 and 10. Maximum screen capacities for both load and displacement were developed for each of the wire gauge sizes along with the screen stiffness. This information can be used for screen selection and for the evaluation and determination of screen performance. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Michael Feroz, Marcus Jensen, James E. Lindell

The Southern Nevada Water Authority (SNWA) operates two water-intakes in Lake Mead, located 20 miles east of Las Vegas, Nevada. Severe drought has caused decline in lake level by 85 feet since 2000 and future declines are expected. SNWA will construct a third deep-water intake to ensure existing water system capacity. This paper describes expected construction challenges for the new project that consists of: an intake structure and tunnel beneath the lake, pumping station, pipeline to connect existing treatment facility, and interconnecting underground adits. The project will be completed in the year 2012 for total estimated cost of approximately $600 million.

Jan 1, 2007

By Jack Parker

Critical width Before we go further into pillar design, we should look into the matter of "critical width," because of its effect on pillar behavior. Critical width refers to the greatest width that the rocks above the mine can span before failure or, if there are pillars, the width to which we must mine before the pillars accept the full weight of the overlying materials. There are theories to help calculate that probable width, and they usually boil down to one-quarter or one-third of the depth of cover; but they don't always fit, and it would be better for us to understand the factors that control local conditions. Critical width may be controlled by the thickness or strength of one or more of the strata above the mining horizon. In a gold mine, we might have a thick granite or basalt above us, perhaps capable of bridging across most or even all of a small ore body. In that case, pillars might have to support nothing, or perhaps just the weaker or damaged rock below the strong main roof. Obviously it would be wrong to design for tributary load on pillars based on some lab-determined rock strength. In some coal mining districts in Utah, huge steps can be seen in the mountain sides, with slopes on weathered shales and vertical cliffs 100 or 200 ft high in thick, hard sandstones. The sandstones are capable of bridging across hundreds of feet, often making mining deceptively easy at first, but it becomes more difficult as greater areas are opened. Sometimes such a mining sequence leads to violent bumps and bursts as the wide spans of sandstone sag and bear down on the working faces, like giant nutcrackers, or as bridges eventually fail, releasing much pent-up energy.

Jan 1, 1993

By C. Asgaard

Asset availability has been a longstanding objective in mining and mineral processing plants around the world. Enormous resources in both dollars and manpower are invested in improvement efforts to achieve higher asset availability. One dimension of asset availability is the time equipment is out of service for large scale planned maintenance activity: grinding mills, kilns, furnaces, mobile equipment, shovels and draglines are all regularly taken out of service for extended repairs and service. The speed, cost and quality of these planned outages provide an opportunity to increase asset availability. Equipment shutdowns are projects that are executed in a compressed time period. This paper will describe how the overall time and cost of equipment shutdowns were significantly reduced at Cliffs Natural Resources Michigan Operations (CNRMO) through the introduction of the Critical Chain Project Management techniques.

Jan 1, 2009

By M. Rieber

Building on earlier work, an analysis relevant to international (Australasian) minerals trade is developed which accounts for both the impetus of globalization and national reaction or protection. At the firm level, integrated multinationals are contrasted with trade service providers. At the industry level tariff and, particularly, such barriers as quotas, standards, labor and environmental issues are explored. Specific areas examined include: location of both inventories and processing, sources of finance and currency risk, shipping availability and terms as related to processing level, residuals management or environmental controls, and “fair” labor standards. Intraregional rather than global trade is currently most likely.

Jan 1, 2002

By J. Pinkley

DSI DYWI Rock Dust application is aiding in enhancing safety and productivity in underground coal mining. DSI DYWI Rock Dust combines wet dusting technology and polymers to allow for drying and lift characteristics for rock dusting. DSI DYWI Rock Dust typically dries within 24 to 48 hours depending upon the mine air velocity and humidity. The DSI DYWI Rock Dust Applicator Machine is a completely hydraulic unit. The DSI DYWI Rock Dust Applicator machine allows for batching of product and face spraying operations in permissible locations. The DSI DYWI Rock Dusting Applicator Machine fits in one half of a battery or diesel scoop bucket for ease of transport. It is completely hydraulically powered by the PTO circuit. The DSI DYWI Rock Dust Applicator unit requires a scoop operator, and a person to operate the spray wand, simple operation with two personnel. The first demonstration was at an underground continuous miner room and pillar coal mine which produced a pilot test period opportunity, which proved to be successful, and has now been in full launch mode with the US underground coal mining industry. A typical batch of operation allows for 250? of roof and rib (19? wide by 6? in height) coverage of DSI DYWI Rock Dust application. The DSI DYWI Rock Dust Applicator contains a hydraulic powered air compressor which allows for 30-50% more coverage per batch by improved dispersion of product via air assist spray nozzle. DSI DYWI Rock Dust will add approximately $0.02 to $0.04 per clean ton of coal cost to the mining operation over traditional rock dust cost depending upon mining height.

Jan 1, 2012

The Mine Safety and Health Administration (MSHA) conducted a respirable dust survey to evaluate the effectiveness of a water curtain utilized for dust control on continuous miner sections. The purpose of this survey was to determine if the water curtain was effective in reducing respirable dust concentrations, since several mines currently use water curtains to control miners? respirable dust exposures. The survey was conducted on a supersection of an underground coal mine, which utilized two continuous miners on the same split of air. Each continuous miner alternated taking a cut so that both continuous miners would not operate at the same time. The underground coal mine is located in Knox County, Indiana. The water curtain evaluated in this survey was located in the last open crosscut between the intake side continuous miner and the return side continuous miner. When the intake side continuous miner cuts coal, its exhaust air would be used to ventilate the return side of the section. The intent of the water curtain was to reduce the intake air respirable dust concentration (generated by the intake side continuous miner) before the air stream ventilated the return side of the section. To determine the effectiveness of the water curtain in reducing respirable dust concentrations, respirable dust sampling pumps were placed on both the intake side and the return side of the water curtain. Additional respirable dust sampling pumps were placed farther downstream from the water curtain to monitor dust levels downstream of the water curtain, but in an area where respirable dust would not be created by anything other than the intake side continuous miner or additional section air. The water curtain and the respirable dust sampling pumps were operated only when the intake side continuous miner was cutting coal. The samples were analyzed for respirable dust and quartz content. The water curtain showed minimal effect in controlling respirable dust and respirable quartz dust, but the reduction was so negligible that this survey could not quantify the reduction. The measured reductions are within the accuracy of the sampling equipment.

Jan 1, 2009

By J. J. Gresham

Homestake’s first links with Australia were established in 1934 but it wasn’t until 1961 that the company established a formal presence in the country. After involvement and success in iron ore and nickel, Homestake made a strategic investment in the Kalgoorlie gold operations in 1975 and now owns 50% of Kalgoorlie Consolidated Gold Mines, operators of Australia’s biggest gold mine. In 1998 Homestake acquired the major Australian gold producer Plutonic Resources, is now firmly established as Australia’s second largest gold producer and is actively seeking further opportunities for growth in the Austral-Asia region. Homestake’s success in Australia has been the result of important strategic alliances, timely investments, a long term commitment to the region and perseverance during periods of depressed commodity prices.

Jan 1, 2001

By S. Johnson

Introduction The mining of aggregates underground has grown steadily over the last 25 years. Growth has come in both production volume and in the importance this segment of the industry is playing in the continuing supply of construction aggregate. Underground aggregate mines will continue to grow in both number of operations and complexity, as the replacement of zoned reserves in metropolitan areas becomes crucial. This growth will result in a shortage of qualified mine managers, possibly limiting the success of these facilities. The aggregate industry will have to modify current practices in order to meet the growing demand for this specialized skill. Segment Growth Underground mining for aggregates is not a new idea. Martin Marietta has been operating underground mines since 1969, and currently operates 16 underground mines ranging in size from 250,000 tpy to 2,500,000 tpy. These mines represent less than 4% of the total number of operating locations, but contributed 9% of the annual production in 2004. Though they range in size and production capacity, the importance is evident. The 2000 United States Census revealed several trends that are of interest to the aggregate mining industry. For the period 1990-2000 the U.S. population grew by 33 million or 13%. There were nine major metropolitan areas with a population of five million or more. These nine areas accounted for 30% of the total U.S. population. More significant was the fact that the population growth in these nine metro areas was 25% of the growth for the entire country. These statistics tell us that the population is expanding in these major metropolitan areas at a staggering rate. The same thing is happening to some degree in every population center. Population growth increases the demand for local aggregate while reducing the available area to mine that aggregate. The need for an economical supply of aggregate to support community expansion is a problem that will grow as older quarries are mined out and closed. This will be an issue that communities of all sizes will have to deal with. A reliable and cost effective supply of quality aggregate is crucial to support community expansion.

Jan 1, 2006

By B. Salopek, D. Rajkovic, D. Rumenjak

In decision making support system, that are used in various fields of environmental protection (environmental impact assessment, environmental management systems, setting environmental standards and regulation, etc.), it is often important to apply various mathematical environmental engineering models. The question of linking environmetal engineering modeling to decision making support system used in environmental protection is not yet methodically solved. The reasons for that could be manifold. Decison making support systems, used in environmental protection, because they are simply taken from bussines decision making, are not often adequate for specific problems raised in environmental protection. On the other hand, there are great number of types of models in environmental engineering, what urges the problem of finding the way of their proper linking with decision making support systems. The application of fuzzy logic in that field is estimated as one of possible solution of the problem.

Jan 1, 2005