Search Documents

By John P. Hager

A special inlet system has been developed for a TOF mass spectrometer that allows the equilibrated high-temperature vapors from an atmospheric-pressure flow reactor to be leaked into the ion source of the mass spectrometer without undergoing any compositional changes. Using this flow reactor - mass spectrometer system and a modified transpiration system (one that allows for the carrier stream to be equilibrated with two different condensed samples) a series of fundamental vapor transport studies were undertaken. The results of these studies are summarized as follows: 1. The vapor species in equilibrium with condensed copper (I) chloride were determined to be Cu3C13, Cu4C14, and Cu5C15. The gas mixture is fifty percent tetramer near the melting point (703°K), with the percentage of tetramer decreasing with increasing temperature. The following thermodynamic results were obtained.

Jan 1, 1977

By D. O. Hamiltion

The ISMS program provided for the development and demonstration of equipment modifications in both conventional and continuous coal mining systems. This report describes activities during the demonstration of the conventional equipment and includes machine performance, results of data gathering, system evaluation, and recommendations for implementing improvements.

Jan 1, 1976

By Kenneth H. Johnston

Records show that waterflooding was tried in Osage County as early as 1934, but it was not economically important until a large unitized flood in the North Burbank field was begun in 1950. Development was rapid and by the end of 1960, there were 70 active water flood projects and 16 active pressure-maintenance projects in the County. The locations and status of the water-flood and pressure-maintenance projects in Osage County on December 31, 1960 are shown in figure 1, and information pertaining to these projects as of July 1, 1960 is given in table 1. For the past several years, Bureau of Mines petroleum engineers have arranged tours of selected waterflooding projects for the spring meeting of the Kansas-Oklahoma Water flood Association. These tours are conducted to demonstrate unique operating methods and new field equipment and to provide additional opportunities for exchanging information. Each of these tours has been supplemented by a published report describing in detail the projects visited. This report has been prepared for distribution during the 1961 spring tour of three waterflooding projects and a pressure-maintenance project in Osage County, Okla. (fig. 2).

Jan 1, 1961

By Kenneth H. Johnston

This publication describes a thermal-recovery project and two waterflood projects in Carter, Garvin, and Stephens Counties, Okla., that will be visited during the 1966 annual tour by the Bureau of Mines in cooperation with the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects arc (1) the movement of heavy (15° to 28° API gravity) crude oil through the reservoir and into the well bore with energy furnished by burning a portion of the crude oil therein; (2) the use of an inverted nine-spot pattern with dually completed injection wells, to produce oil from deep (8,200 to 10,200 feet) reservoirs; and (3) the flooding of five sand lenses separately by using controlled water injections through multizone completed injection wells. Discussion of the individual projects includes information on their early history, method of completing and operating wells, source and treatment of injection fluids, oil production decline curves, and the results obtained from the development.

Jan 1, 1966

By David Bendersky

This report covers a technical and economic investigation of old electrical power systems, equipment and practices being used in the metal/non-metal raining industry. The principal sources of information were the MSHA District offices, visits to representa¬tive mines and mills, equipment manufacturers and the literature. A list of 85 mines and mills, submitted by the MSHA Districts as candidates for this study, is given and their characteristics are analysed. The electrical power systems and practices at the 10 mines and 9 mills which were visited are described. The principal areas which do not conform to standard electrical practices are discussed with emphasis on the safety aspects of these practices. The costs to update electrical power systems and practices in metal/non-metal mines and mills are given. The principal findings of the study are summarized and recommendations are submitted.

Jan 1, 1980

The Bureau of Mines conducted large-scale laboratory copper ore leaching tests to enable improving copper recovery from large dump-leaching operations. This was done by comparing leaching progress when copper was recovered from recycled leach liquor either by cementation or by solvent extraction. Copper was leached from 7-ton ore samples at room temperature using pH 2 ferric sulfate solutions. With are samples containing 11 percent minus 0.5-inch fines, no marked advantage in using either of the copper recovery methods was evident after 416 days of leaching. With ore containing 32 percent minus 0.5-inch fines, solvent extraction of copper was advantageous in that 60 percent of the copper was extracted after 568 days, whereas only 48 percent of the copper was extracted when cementation was used. Less acid was consumed during leaching when solvent extraction, rather than cementation, was used for copper recovery. Iron, contributed by cementation with scrap iron, plugged the ore bed containing 32 percent fines.

Jan 1, 1981

By L. M. Irwin

This Bureau of Mines investigation relates the physical properties of copper reverberatory furnace slags to changes in composition, The smelting of upper Michigan copper ore presents some problems that probably differ from those of other copper smelting areas. The study of these problems has, however, provided important data regarding slags in general and therefore will be of value to other operations as well. Conclusions reached from this study were: (1) Slag fluidity and refractive indices varied directly with the iron content and inversely with silica, lime, and alumina, and (2) there was no apparent correlation between slag fluidity and its copper content.

Jan 1, 1962

By Kenneth H. Johnston

This publication describes a thermal-recovery project and two waterflood projects in Carter, Garvin, and Stephens Counties, Okla., that will be visited during the 1966 annual tour by the Bureau of Mines in cooperation with the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects arc (1) the movement of heavy (15° to 28° API gravity) crude oil through the reservoir and into the well bore with energy furnished by burning a portion of the crude oil therein; (2) the use of an inverted nine-spot pattern with dually completed injection wells, to produce oil from deep (8,200 to 10,200 feet) reservoirs; and (3) the flooding of five sand lenses separately by using controlled water injections through multizone completed injection wells. Discussion of the individual projects includes information on their early history, method of completing and operating wells, source and treatment of injection fluids, oil production decline curves, and the results obtained from the development.

Jan 1, 1966

By P. M. Daling

This report, sponsored by the U.S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures, and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982

By A. G. Kim

Methane and other hydrocarbon gases, byproducts of coalification, are emitted from coal at widely varying rates and often present ventilation problems during mining. The air in some coal mines apparently contains no methane. To determine if coals from mines which bid no history of detectable gas emission contained adsorbed methane, samples of coal at the shaft bottom and at an active face were obtained and placed in sealed metal cylinders. The atmosphere around the coal was sampled and analysed by gas chromatography. Methane, ethane, ethylene, propane, propylene, and butane were found to have been desorbed from these coals. Hydrogen and helium were also detected. An estimate of the amount of residual gas per ton A coal indicated that coal samples from the active face generally contained more adsorbed gas than coal samples obtained from the shaft bottom, although in both instances the total amount of gas was relatively small.

Jan 1, 1973

By Rudolf E. Greuer

The existing computer programs for the simulation of ventilation systems under normal ventilation conditions are reviewed and a suitable program for including the influence of mine fires is selected. New program parts are written for the consideration of methane productions in coal mines, heat and gas productions of mine fires, temperature and air composition changes in ventilation systems, and the ventilation forces resulting from the latter. Other program parts are provided for the detection of danger zones and reversed air currents and for the inclusion of recirculated air currents in the network analysis. Existing program and new program parts are combined. The resulting new program can be used for a multitude of assignments. It is designed for the practical ventilation engineer and should be applicable to all types of ventilation emergency plans, in particular mine fire plans. The organization of the program and its mathematical basis are described. A FORTRAN IV listing and several flow diagrams are included. Eight executed examples are discussed, input and output for these examples explained. Storage requirements and execution times are estimated.

Jan 1, 2011

By Victor R. Spironello

The Bureau of Mines has conducted studies of the slags related to ferrous technology to evaluate experimentally acceptable substitutes for the auxiliary flux, mineral fluorspar, in steelmaking operations. Comparative heats were made in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF) to evaluate a waste material known as "used potlining." Used pot lining is recovered from alumina reduction cells after its useful life and contains significant levels of fluorine and sodium in various compounds. This material in both lump and pelletized form provided adequately fluid slags, based on observations made during BOF operation. No adverse effects were found on furnace performance, metal and slag chemsitry, the strength of the steel produced, or the environment. Fluorine recovery in the slag was about the same as that obtained when using fluorspar, as were the losses to the scrubber water and solids. No difference was observed in furnace-refractory attack, as determined by the level of magnesia in the slag. The sodium recovered in the slag apparently also contributed to fluidity, since the fluorine input was at about two-thirds that of the fluorspar. Used potlining was determined experimentally to be a satisfactory substitute for fluorspar in basic oxygen steelmaking.

Jan 1, 1982

By Fred Leighton

The Bureau of Mines has developed rock noise source location techniques that may be used to obtain precise and practical source locations from micro-seismic field data. These techniques enable one to monitor all or any part of a rock structure and map progressive stress buildup or rock movement. Thus, the microseismic method of determining instability in rock structures is becoming an invaluable engineering tool for the mining or civil engineer engaged in rock excavation and construction.

Jan 1, 1970

By Pakalnis Rimas, Lyndon Clark, Tom Brady

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate data on weak rock masses into existing design relationships, with an emphasis on updating the span design curve for manned entries and the overbreak curve for longhole entries. Both curves were originally developed at the University of British Columbia, Vancouver, BC. The original database has been augmented by information from mines throughout the United States, Canada, Australia, and Europe. The common factor in all these mines is the presence of a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be stabilized so that the mineral-bearing rock can be extracted safety. The current NIOSH research attempts to provide rock mechanics tools to assist a mine operator in making economic decisions that will also ensure a safe working environment. This paper documents the Nevada database with a special emphasis on Nevada underground gold mines.

By Joseph Grumer

An instrumented spherical vessel has been used for many years to study laminar combustion waves. Concurrent measurements of flame speed and pressure-rise rates have led to evaluations of burning velocities, the pressure dependence of the burning velocity, and the expansion ratios of the gases passing through the combustion wave. For the most part, these studies have involved flames initially at atmospheric or subatmospheric pressure. The old spherical vessel used by the Bureau of Mines was not designed for use at elevated pressures. Moreover, being made of wrought iron, it was susceptible enough to corrosion to prohibit its use with many combustible mixtures that figure in industrial research. In mid-1956, under sponsorship of the Office of Naval Research, the Bureau undertook the development of a stainless steel spherical vessel capable of withstanding explosions of gaseous mixtures at initial pressures as high as 20 atm. and initial temperatures as high as 250° C. The design called for a double array (cross) of closely spaced small windows for observation of the flame as it traversed the vessel and a piezoelectric transducer to measure concurrently pressure-rise rates. Because no commercial contractor was willing to bid on the construction of such a vessel, it was built at the Bureau's Bruceton machine shop.7

Jan 1, 1961

By William J. Campbell

Expansion measurements of platinum, added as an internal standard, are used for thermal calibration of X-ray cameras and diffractometers. Accuracy of the temperatures derived by this technique depends on the precision of expansion measurements and the reliability of reference expansion data. Temperature measurements to ± 1° C. require ?d or ?a to be determined within ± 0.001 percent. Selected expansion data are concluded to be reliable to 2° C., 5° C., and 25° C., over the temperature ranges 0° C. to 700° C., 700° C. to 1,000° C., and 1,000° C. to 1,700° C., respectively. Tabular expansion values from 25° C. to 1,700° C. in 2° C. intervals were calculated from the following equation; Expansion, percent = [8.91 + 1.28 x 10-3(t-25) + 0.04 x 10-6(t-25) ] [t-25.104 ] These tabular values facilitate future corrections of published temperatures as more reliable expansion-temperature data become available.

Jan 1, 1962

By David J. Kusler

This study is an appraisal of the feasibility of recovery and the possible chemical and physical uses of the limestone from the Greenbrier Formation in western West Virginia. Data on minability, occurrence, quality, and markets were obtained from published and unpublished sources and by a limited mail survey combined with personal contacts. The estimated costs of recovery by deep mining techniques are considerably higher than competitive surface and shallow subsurface operations. Compositional in formation available for this study was limited but indicated the suitability of the limestone for most physical uses and some chemical process uses in appraisal of the uses and demand reveals that immediate markets may be difficult to establish, but for some uses long-term prospects may be encouraging, especially if the quality of limestone would be suitable for lime manufacture or use as metallurgical fluxstone.

Jan 1, 1968

By Robert M. Doerr

The research objective was to determine the effect of aluminum alloy additions on the oxidation behavior of cobalt-nickel alloys. Thirty high-purity alloys were reacted with 02 at 0.5 atm at 1,351°, 1,389°, and 1,429° K in a volumetric apparatus for about 300 min. The alloy compositions consisted of Co-Ni master alloys (0, 22, 50, 70, 91, and 100 wt pct Ni) with aluminum additions of about 0, 1, 2, 4, and 8 wt pet. Large early deviations from, or changes in, the parabolic rate constant were encountered, but in most cases, the reaction rate declined approximately in accordance with the parabolic rate law. A sharp peak in the parabolic oxidation rate constant was observed for specimens containing a to 22 percent nickel and 1 to 2 percent aluminum at 1,351° K, and the rate constants for these compositions were lower at the higher temperatures. Specimens containing 8 percent aluminum reacted far more slowly than did any of the others.

Jan 1, 1971

By John R. Bartels

Remote operation of continuous mining machines has enhanced the health and safety of underground miners in many respects; however, numerous fatal and non-fatal continuous miner struck-by accidents have occurred. In an effort to prevent these injuries, NIOSH researchers at Pittsburgh Research Laboratory studied the workplace relationships between continuous miner operators and various tramming tasks of the equipment using motion capture data, operator response times, and field of view data to evaluate the factors influencing operator-machine struck-by events (contact with a solid object) in a virtual mine environment. It is not feasible (nor ethical) to use human subjects to directly evaluate factors that precipitate such injuries. However, use of motion analysis data and digital human models can facilitate analysis of struck-by accident risk by allowing investigators to manipulate factors that influence injury. Factors included in this study included machine speed, direction of escape, the direction the operator was facing relative to the machine, work posture, distance from machine, and operator anthropometry. Close proximity to the machine, high machine tramming speeds, a right-facing orientation and operator positioning near the tail all resulted in high risk of being struck.

Jan 1, 2008

By John A. Johnson

For the purpose of comparing the amounts of dust produced by various mining operations, samples of atmospheric dust were collected during a complete cycle of drilling, blasting and mucking at or near the face of the Bureau's Mount Weather testing adit while the efficiency of several types of stemming in metal-mine blasting was being investigated. ACKNOWLEDGMENTS All gas samples were analyzed in the laboratory of the Bureau of Mines Gas Section at Pittsburgh, Pa.

Jan 1, 1939