Search Documents

By Aldo L. Furno

Sufficient quantities of combustible vapors are released by some sulfurs to produce flammable atmospheres under prolonged storage. Hydrogen sulfide and carbon disulfide appear to be the principal flammable constituents in the vapor space above molten sulfur. If sufficient carbon disulfide is present, ignition of the vapor-air mixtures can occur spontaneously on contact with the heated surfaces found within storage tanks.

Jan 1, 1963

By James P. Bennett

In this Bureau of Mines study, portions of four acidproof bricks (two red shale and two fireclay) were exposed to 20 wt pct RCI at 900 C for periods of 30 days. Three different techniques were selected to deter-mine volume expansion of these materials after exposure. Linear expansions ranging from about 0.02 to 0.12 pct were noted from Ta pin and dilatometer measurements. The use of strain gages to measure expansions was not successful. The red shale and fireclay brick with the lowest apparent porosities had the lowest expansions. Expansion data obtained by direct measurement of samples exposed for 30-day periods or by dilatometric measurement of autoclaved samples ex-posed for 2 h were comparable. This suggests the use of an accelerated autoclave exposure procedure for determining volume expansion effects of ceramic materials in acid environments.

Jan 1, 1985

By G. W. Jones, I. Spolan

"INTRODUCTION The operation of internal-combustion engines at high altitudes and the general aspects of combustion processes in rarefied atmospheres have created considerable interest in the problem of ignition and flame propagation at low pressures. Nuckolls, Matson, and Dufour 4/ have published results on the effect of low pressures on the propagation of flame in gasoline vapor-air mixtures in vessels of large capacity. The volumes of their test equipment varied in capacity from 0.425 to 125 cubic feet. Various sources of ignition were employed. These authors found that the explosive range of gasoline vapor in air decreases with decreasing pressure at pressures considerably below atmospheric, until a limiting absolute pressure of about 33 mm. mercury at ordinary temperature is reached, at which point no appreciable flame is propagated.Experiments carried out at the Bureau with natural gas-air mixtures at reduced pressures have shown 5/ that the limits of inflammability are but little affected at reduced pressures down to 175 mm. mercury. As the pressures of natural gas-air mixtures are reduced below atmospheric, the mixtures become more difficult to ignite; however, if a suitable source of ignition is employed, the limits of inflammability are as wide at 175 mm. mercury absolute pressure as they are at atmospheric pressure. In view of these observations with natural gas-air mixtures, it appears important to investigate gasoline vapor-air mixtures for possible similar behavior. For this reason the tests herein described were carried-out."

Oct 1, 1946

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"An electro-optical method was used to quantify superoxide (SO) release from single rat pulmonary alveolar macrophages (PAM) exposed in vitro to respirable quartz and kaolin dusts and in vivo to quartz. Release was determined by measuring the reduction of nitroblue tdrazolium (NBT) to a diformazan precipitate at 550 nm from video-recorded images of individual cells. In vitro exposure to 0.025 or 0.05 mg/ml kaolin for 40 minutes resulted in no significant differences in either the total diformazan produced (max) or the maximum rate of diformazan production (R)./n vitro exposure to 0.025 mg/ml c1uartz decreased max 38 percent while no significant change was found using 0.05 mg/ml. However, R was decreased 31 percent and 24 percent for the low and high dose, respectively. In contrast, PAM obtained from animals exposed in vivo to quartz dust for two or four weeks in inhalation chambers exhibited increased production of diformazan. However, only PAM analyzed three days post-exposure showed significant increases, while PAM from animals sacrificed ten or 31 days post-exposure were not significantly different from control. The combined in vitro and in vivo quartz results might suggest that there is an initital acute response to exposure that decreases the ability of PAM to produce SO, followed by recruitment of production of PAM with increased SO producing capability. It appears that removal of animals from the source of exposure permits PAM to return to control levels of SO production by31 days. Whether this would be true for chronic exposure remains to be elucidated.IntroductionPulmonary alveolar macrophages (PAM) protect the lungs by phagocytizing foreign debris and bacteria.(1) This process involves ingestion as well as destruction of foreign matter. Phagocytosis usually is accompanied by a respiratory burst which increases cellular oxygen consumption leading to the release of highly reactive oxygen metabolites.(2) These agents have been implicated in the killing of bacteria by phagocytes, but they have also been shown to be toxic and,have been linked to cancer, emphysema, arthritis, diabetes, and other diseases.(3) Toxic effects may be a result of 1) an abnormally low production of metabolites, resulting in damage to lung tissue by the respired bacteria and/or dusts; or 2) an abnormally high production resulting in direct damage to lung tissue by metabolites themselves."

Mar 1, 1989

By K. J. Maggs

The U.S. Bureau of Mines has investigated the chemical vapor deposition of diamond films on tungsten substrates. The effects of deposition parameters on the adhesion of the films was determined. The films were produced using a hot filament chemical vapor deposition system. Parameters investigated were substrate temperature and methane concentration in the feed gas. Film quality, morphology, and composition were characterized by scanning electron microscopy and Raman spectroscopy. Adhesion testing was performed using an indentation technique, and the results were quantified by relating adhesion to interface fracture toughness. Diamond films with well-faceted crystalline morphology with grain size greater than 1 µm had poor adhesion properties regardless of substrate temperature or methane concentration. Diamond films with smooth morphologies consisting of rounded clusters of small (<0.2 µm) diamond crystallites and amorphous carbon phases displayed much higher adhesion, although the conditions that led to the growth of these films are not understood.

Jan 1, 2010

By Will H. Coghill

The jig men of the Tri-State (Joplin-Miami) zinc district complain about the flakiness of their mill feed. They believe that the flakiness of the composite grains of gangue and mineral are to blame for losses of zinc; that is, that the flaky grains in the jig tailings have higher zinc tenor than the cubical grains. Although the evidence which follows contradicts this belief, no effort is made to give a final and conclusive answer. On the other hand, there is outlined a positive and mechanical method which the operator may use to pursue this and similar investigations. DISCUSSION OF SCREENING METHOD Hand-sorting is obviously not satisfactory for separating cubical grains from flaky grains because the personal influence can not be removed. Screens, however, may be used with success. A set of each of two types of screens is required; namely, the square-hole type and the rectangular (rectang, oblong) type. The square-hole screens must be of the double Tyler scale; that is, the order of the sieves should be after the fourth root of two instead of the customary square root of two; close sizing is important. The size of the rectang screens may be selected by trials so that a part of the material already closely sized on the square-hole screens, will pass the oblong holes. Obviously, the cubical grains will remain on the rectang and the flaky grains will pass through. Hence the mode of operation is to screen first on square-hole screens and then split the products on the oblong-hole screens.

Jan 1, 1928

By Paul M. Tyler

The value of mica depends chiefly upon the size of the flat sheets into which it can be split and also upon whether it is clear or stained. Muscovite (white mica) and philogopite (amber mica) are the micas of commerce. Biotite (black mica) and other varieties are virtually unsalable. Vermiculite, an altered mica having the extraordinary property of expanding greatly when heated, preferably should not be classed commercially as mica. Mica is marketed as (1) cut or uncut block, (2) sheet, (3) splittings, and (4) wet or dry ground mica. In the United States, mica that will not yield flat films over about 1-1/2 inches square, or that is ruled, rumpled, or flawed in any way, can be sold only as scrap, its sole use being for making ground mica. Only sizes that will yield rectangles 1-1/2 by 2 inches or larger can be classed as sheet quality; slightly smaller sizes may be classed as punch, and under certain circumstances still smaller sizes, down to about 1 inch square, may be used for splittings, which are mostly a thousandth of an inch thick or even thinner. Splittings, however, are produced in large quantities only in British India, where labor costs very little. Even there the work is done mostly by children, who not only work cheaper but have a delicacy of touch that enables them to do the splitting faster and better. No mechanical process yet devised will permit ordinary splittings to be made economically in the United States.

Jan 1, 1938

By Michael G. Zabetakis

The autoignition temperatures (A.I.T.&apos;s) of natural and synthetic lubricants in air were generally found to decrease with increasing pressure. Of the two types of fluids, synthetic and natural, studied in some detail, the phosphate esters had higher A.I.T.&apos;s at any pressure between 1 and 200 atmospheres than the mineral oils. Most of the A.I.T. data obtained in this study obeyed the relationship predicted by Semenov&apos;s theory of ignition.

Jan 1, 1962

By Jalna R. Zatko

The Bureau of Mines has developed and constructed an apparatus that is capable of measuring concentrations of high-molecular-weight polymers in solution at 10 ppm and less. A means for determining low concentrations of polymeric solutions was devised that was independent of slight fluctuations in solvent quality in order to measure polymers in effluent prior to recycling of the recovered solution. The concentrations of polymers ore related to a measured pressure drop observed during turbulent flow of the solution. Low concentrations of polymers of ethylene oxide and acrylamide (frequently used as flocculants for clay waste systems) in aqueous and salt solutions have been successfully measured on the apparatus constructed by the Bureau.

Jan 1, 1981

By R. K. Koch

The Bureau of Mines produced several series of titanium castings in order to investigate the feasibility of producing commercial-grade titanium castings in bentonite-bonded olivine or zircon sand molds. The use of these molds for titanium casting was investigated as a possible alternative to the industrially used rammed graphite process. Parameters investigated were mold mixtures, mulling, gating, venting, drying, and mold washing. The investigators found that castings with superior ductility and fatigue life, compared with rammed graphite castings, could be made by fume-free pro-cesses in molds bonded by western bentonite, using either olivine or zircon sand. Zircon molds were satisfactory for both light-and heavy-sectioned castings. However, olivine molds were suitable only for light-sectioned castings because the mold-metal reaction became excessive during the pouring of heavy-sectioned castings.

Jan 1, 1981

By A. E. Nagel, J. E. Carpetta, M. G. Zabetakis, T. D. Moore

The method of moving averages was found useful in assessing the nature of methane emission in coal mines. Emission rates were influenced markedly by the presence of abandoned oil and gas wells in the vicinity of the mine. Such wells appeared to increase the flow rate of methane into the mine by a factor of 2 to 30 in an active mine in the Pittsburgh coal seam.

Jan 1, 1972

By J. B. Gayle

Many investigators have reported studies of size distributions for particulate solids ; usually , these have involved the fitting of size distribution data to a particular mathematical function . Such studies are of unquestioned value and have contributed much worthwhile information regarding the breakage mechanisms for a variety of brittle materials . In connection with a Bureau of Mines study of the size distribution of coke , which has been subjected to the standard American Society for Testing Materials (ASTM) tumbler test , attention was focused on the relation between the 1 -inch tumbler index (usually considered to be indicative of the ability of coke to resist degradation by impact ) and the 1 /4 - inch tumbler index ( indicative of the ability to resist degradation by abrasion ) . Specifically , it was noted that for certain sets of data the correlation coefficients denoting the relation between these indexes were positive ; for other sets of data , these coefficients were negative . Preliminary consideration of this problem indicated that the usual interpretation placed on correlation coefficients was erroneous in this particular instance because the variables being correlated were necessarily related . The work described in this report was undertaken to clarify the interpretation of results of correlation studies for variables of this type .

Jul 1, 1960

By R. T. DeWoody, W. C. Miller, W. Chester

Studies were made to determine the effect of the shape of a pneumaticrock- drill exhaust muffler on its efficiency, and the origin and reduction of exit noise from the mufflers. Tests of mufflers of three different shapes proved that the shape is not critical and that a muffler could be incorporated into the shell of the drill. Petal diffusers are beneficial in reducing exit noise but add another projection to the machine. Increasing the number of exit openings while maintaining the same area of exit opening has a markedly beneficial effect on the exit noise and appears to be the most satisfactory treatment.

Jan 1, 1964

By Spencer P. Howell

One of the important problems in metal mining , tunneling or quarrying is the most economical method of bringing down the ore or rock . The two factors having great influence in determining this are arilling and blasting costs . In considering the efficiency of the explosive used , the diameter of cartridge has always been supposed to play an important part . However , the Bureau's attention has been called to the lack of definite data on the effect of cartridge diameter on the strength and sensitiveness of high explosives . This information is especially valuable to the user of explosives as it assists him to determine what diameter of borehole is most economical . A paper* on "The effect of cartridge diameter on the strength and quickness of high explosives " was submitted to the sub- committee on Drills and Drill Steel of the 24th Annual Convention of the American Mining Congress by Charles S. Hurter , Technical Representative of the E. I. duPont deNemours and Co. In this paper Mr. Hurter points out that the physical characteristics of an explosive most affected by the diameter of cartridge are rate of detonation and sensitiveness to explosion by influence , and that both increase with increase in diameter . As there is a continuing tendency to the use of smaller diameter drill holes in order to lower drilling costs , and as the smaller drill hole requires a smaller diameter of explosive cartridge than larger drill holes do , this paper has been prepared to show the effect the diameter of cartridge will have on the strength and sensitiveness of the high explosives which may be used . Accordingly , the Bureau of Mines , in cooperation with the Institute of Makers of Explosives , has carried out a series of tests to show the effect of cartridge diameter on the strength and sensitiveness of certain high explosives .

Jan 1, 1923

By ALICE V. Petar

Thallium is one of the rare metals that has come into commercial use within recent years . Its comparative scarcity , combined with a resemblance to the common metal lead , have retarded the development of uses for thallium . Although production is still measured in pounds rather than in tons , it is now finding application in a number of fields . Perhaps the earliest commercial use of thallium was as a constituent of optical glass of higher refractive power than similar glasses containing lead . One of the later applications to attract attention was the use of the oxysulphide in a sensitive electrical device similar to the selenium cell . The " Thalofide " cell , which was patented in 1919 , constituted for a time the most important outlet for thallium. During the next few years the limited use of thallium and its salts in other fields was insufficient to absorb an annual production of a few hundred pounds , and the price dropped from $ 16 or $18 per pound in 1922 to $ 5 per pound in 1924 . Beginning in 1925 several new uses were developed , especially as a poison for rodents and ants , and as a result the demand for thallium increased sufficiently to cause a recovery in price to the present level of from $12 to $15 per pound .

Jun 1, 1931

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSB systems are safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by over 30%, on the average, with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include better fire suppression systems, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

By George S. Rice

"INTRODUCTION During the past 4 or 5 years the frequent occurrence of bumps in coal mines of the Cumberland field, in Harlan County, Ky., and Wise County, Va., has caused much apprehension among miners and mining officials of that region.These bumps have caused many deaths and injuries, and have been increasing in frequency. Eight men were killed and a number injured by bumps in the first 4 months of 1934. Their unpredictable occurrence and the usual absence of any preliminary warning tremors or sounds, such as ordinarily precede a large fall of roof, cause fear of other bumps and impair the morale of mine workers.Acknowledgments This report on bumps in coal mines of the Cumberland coal field of Kentucky and Virginia is based on an investigation made at the urgent request of .the Harlan County Coal Operators Association, through James F. Bryson, director of safety of the association, to the Director of the United States Bureau of Mines, following a series of disastrous bumps in. Harlan County, Ky., and Wise County, Va. The request was granted and the writer detailed to undertake the investigation, which was made in June 1934.The officials of certain operating companies in the Cumberland field gave every facility for examining the conditions accompanying bumps in their mines. The writer is most grateful to them for the courtesies shown; to J. F. Bryson, to J. F. Davies, district engineer, Safety Division, U. S. Bureau of Mines, who accompanied the writer throughout his trip to the vari¬ous mines and gave him much assistance and detailed information regarding the occurrence of bumps; and to Dr. David White for reviewing the geological descriptions,Definition of Bumps ""Bumps"" are phenomena comparatively rare in the coal fields of the United States and, for that matter, in the coal fields of the world, because for their occurrence certain exceptional natural conditions are required strong, massive strata of sandstone or conglomerate above the coal and a fairly strong floor, as will be described in detail later."

Jan 1, 1935

By C. H. Schack

Extractive metallurgy techniques currently employed to recover silver from primary ores and secondary scrap were reviewed and evaluated to identify and delineate metallurgical problems whose resolution would increase the supply of silver from domestic materials. The survey revealed that practically all primary silver is recovered by froth flotation concentration of various types of ores, followed by smelting and refining of the separate lead, copper, and zinc concentrates. Silver losses during the complex processing are, with rare exception, inconsequential. Furthermore, any silver production gain from base metal ores, which contribute about two-thirds of the total primary silver, is directly dependent no improvement in the market for the base metals. Statistical data on new and old silver scrap are wholly inadequate to make reliable conclusions about scrap processing problems and the possibility of increasing the recovery of silver from the many forms of secondary silver-bearing materials. The available information indicates (1) that efficient silver reclamation practices are employed by the larger users of silver, and (2) that recovery of additional secondary silver involves solution of problems of collection rather than of processing. Several possibilities exist for limited increases in silver production from primary ores by improvement in metallurgical practices. Specifically, research is needed to (1) solve the problem of recovering silver from the copper ores of the Copper Range district, Michigan; and (2) devise economically feasible methods for recovery of silver from presently marginal or submarginal ores char because of grade, location, and frequently complex nature cannot presently be exploited by conventional techniques.

Jan 1, 1965

By P. C. McWilliams

Researchers at the U.S. Bureau of Mines investigated the use of close-range photogrammetry and subsequent stereo digitizing to obtain data from rock fracture roughness profiles. The photogrammetric process yielded results that were acceptable but somewhat inferior to those obtained by a mechanical profilometer. On the basis of this study, further pursuit of photogrammetry as a data collection method in mining is proposed. Fractal geometry was investigated as a means of measuring the roughness of rock fracture profiles. Four fractal algorithms were used: divider method, modified divider method, box method, and spectral method. A comparison of the methods gave ambiguous results. Brown&apos;s modified divider method provided the best means of obtaining the fractal dimension. Shear strength estimates were obtained using the parameters of the modified divider method and Myers&apos; Z2 measure. Because of differences in results when comparing the different ways of obtaining the fractal dimension, future users of fractals in studies of rock fractures are advised to cross-check their results carefully.

Jan 1, 2010

By L. A. Readdy

Pilot Hole "X" was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine will be drilled. The history of the drilling of Pilot Hole "XI&apos; is presented. This historical summary provides the details of method used during the drilling of this hole. Problems encountered during drilling are discussed. The quantities of drilling mud and other materials used to drill the hole are documented.

Jan 1, 1977