Search Documents

By G. L. Hundley

The Bureau of Mines has devised a procedure to recover chromium chemicals from concentrates derived from low-grade domestic chromites. These domestic chromites contain silicon and aluminum impurities at levels that are too high to permit processing by present industrial processes. The Bureau procedure consists of reacting chromite with molten NaOH under oxidizing conditions to form sodium chromate (Na2Cr04)' The reaction product is leached with methanol to recover the majority of the unreacted NaOH, then with water to extract the Na2Cr04 and the remainder of the NaOH. The Na2Cr04 product is recovered by evaporative crystallization from the aqueous solution. This report presents laboratory results of studies to determine the optimum leaching conditions for the reaction products of several domestic chromite concentrates. Results of solution purification and crystallization studies are also presented. The concentrates are from a variety of sources including the Stillwater Complex in Montana, Red Bluff Bay and the Kenai Peninsula in Alaska, and a Ni-Co laterite from southern Oregon. Sodium chromate crystals were produced that contained less than 0.01 pct NaOH.

Jan 1, 1988

By W. A. Selvig

"The purpose of the investigation described herein was to determine how closely different laboratories can check one another in making determinations of fusibility of coal ash with the De Graaf electric coal-ash fusion furnace: how well duplicate determinations by the same laboratory will check, and how the results with the De Graaf furnace compare with those of the standard gas-furnace method of the American Society for Testing Materials.4Thanks are due the following laboratories who cooperated in this study by making fusibility tests with the Do Graaf electric coal-ash fusion apparatus: J. J. Brennan, testing engineer, Northern States Power Co.; R. E. Gilmore, superintendent, Fuel Research Laboratories, Canadian Department of Mines A. T. Leavitt, president, and W. Mueller, chief chemist, Hamilton By-product Coke Ovens. Ltd.; Edgar Stansfield, chief chemical engineer, Scientific and Industrial Research Council of Alberta. Canada; and H. S. Vassar, laboratory engineer, Public Service Electric and Gas Co.The ash-fusibility determinations by the standard gas-furnace method were made in the Coal Analysis Laboratory of the Bureau of Mines at Pittsburgh under the direction of H. M. Cooper, associate chemist. The investigation was made at the suggestion of A. C. Fieldner, chief engineer, Experiment Stations Division of the Bureau of Mines.Routine determinations of the fusibility of coal ash are made in the laboratories of the United States Bureau of Mines by the gas-furnace method. This method was standardized after considerable experimentation5 on the nature of the fusion of coal ash and the various factors which affect its determination. The method was subsequently adopted by the American Society for Testing Materials as one of its standard tests."

Jun 1, 1930

By K. E. Soroka

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned coal fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,0000 C (1,832° F), and could be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first held field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the 1900's and was surface mined in the 1940's. In the winter of 1961-62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated but not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report is the fifth in a five-part series that describes the Calamity Hollow Mine Fire Project. The first report, part 1, describes the design and construction of the field installation. Part 2 will present the results of a continuous 4-month burnout operation. (Because part 2 involves the analysis of a substantial body of data, it will not be published until after publication of parts 1, 3, 4, and 5.) Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 deal with the closeout phase of the field demonstration. Part 4 describes the procedure used to quench the fire, and this part (part 5) describes the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is sufficient for energy utilization, and (3) water injection-fume exhaustion is a potentially effective method for cooling large underground fire zones. Further investigations of both Burnout Control and the water-injection-fume exhaustion quenching procedure are planned.

Jan 1, 1986

By Stephen C. Tadolini

The U.S. Bureau of Mines conducted a laboratory investigation designed to evaluate the stress and deformation characteristics of fully grouted roof bolts subjected to various magnitudes of end loadings. The experiment and subsequent analysis were completed, utilizing axial deformation data obtained -ultrasonically from forty-one 4-ft, grade 40 roof bolts, with a total of 132 measurement locations along the lengths of the bolts. The ultrasonic measurement instrumentation used in this investigation allowed for elongation measurements without requiring extensive bolt modifications. The results indicate that approximately 39 pct o{ the applied end load dissipated within the first 3.4 in of the bolts. However, only 3 pct of the applied load was realized beyond 28 in of the grout column. Data are presented individually for every 6-in increment of bolt length, and analysis was performed using statistical, nonlinear equations developed for 5,000 and 8,000 lb loading conditions.

Jan 1, 1990

By M. M. Barr

Rapid expansion of the titanium-metal industry focused attention upon ilmenite as a possible substitute for the more expensive and less abundant rutile in producing titanium tetrachloride. Most of the rutile available for this use is imported. Preliminary studies were undertaken to determine the chlorination characteristics of high-titanium slags produced by electric-arc furnace smelting of alluvial Idaho ilmenite at the Federal Bureau of Mines Northwest Electrodevelopment Experiment Station, Albany, Oreg. Low silicon, calcium, and aluminum contents of the slags enhanced their potential value for chlorination.

Jan 1, 1958

By S. L. Weber, V. Castranova, D. E. Banks, J. K. H. Ma, Y. Rojanasakul, J. Y. C. Ma, M. Bhat

"The mechanism of bleomycin-induced pulmonary fibrosis is not ye: clear. Recent studies have shown that alveolar macrophages (AM) can be stimulated by bleomycin in vitro releasing inflammatory cytokines, suggesting that the interaction of bleomycin with AM is an important step in the drug-induced fibrotic process. Bleomycin is known to bind DNA and generate oxygen radicals through complexation with Fe2+ and oxygen. To provide,more insight into the cellular oxidative property of bleomycin, v.s have developed a fluoromicroscopic method using 2',7'-dichlorofluorescin diacetate (DCFHDA) as an oxidative fluorescence probe to study the deomycin-induced intracellular oxidation in rat AM and the inhibition of the oxida¬tion by taurine, a compound known to inhibit the bleomycin-induced fibrosis. Bleomycin at 5 to 20 ug/ml has a moderate stimulatory effect (1.87- to 2.66-fold) on the secretion of superoxide anion. A high concentration of bleomycin (20 ug/ml), however, inhibits cell response to zymosan-induced secretion of superoxide anion. At 4 ug/ml, bleomycin has no effect on cell membrane integrity or morphology but results in a significant increase in intracellular oxidation. This oxidative process is Fe2-,-dependent and is accompanied by an increase in intracellular calcium (35 nM). Both the intracellular oxidation and calcium rise induced by internalized bleomycin are inhibited by pretreatment of cells with varying concentrations of taurine (25, 125, and 187.5 uM). The inhibitory effect on intracellular oxidation .vas found to be 36, 57, and 60%, respectively. These results demonstrate a stimulation-inhibition relationship between bleomycin and taurine on re cellular oxidation at a subcytotoxic dose of bleomycin, suggesting that the oxidative effect of the intracellular bleomycin-Fe2 complex is important in the initiation of the fibrotic process. — Environ Health Perspect 102 (Suppl10):91-96 (1994) IntroductionThe pulmonary system is most susceptible to oxygen radical-induced diseases due to its constant exposure to the highest oxygen tension, and the potential encounters with oxidant gases such as ozone, nitrogen oxides, and toxic doses of dust particles. The lung is also a well-perfused organ and thereby vulnerable to the effect of circulating xenobiotics such as paraquat, and, bleomycin, which is known to cause pulmonary injuries (1). Alveolar macrophages (AM), which act as a means of defense by phagocytizing inhaled dust particles and microorganisms while increasing production of reactive oxidative species, have been shown to play an important role in mechanisms leading to oxidative lung injury and fibrosis (2-4)."

Dec 1, 1995

By G. S. Scott

[In the course of the investigation the Bureau of Mines is carrying on to determine the causes, behavior, and control of mine fires, the detection of incipient heating underground in the mines and above ground in refuse banks has received consideration. A report has been published5/ describing apparatus and tests made on anthracite to determine the amount and composition of the a oxidation products when normal dry air was passed through it at temperatures varrying from 100° to 350° C. These tests showed that the amount of evolved gases and their relative proportions varied with the temperature. From these results, graphs were prepared by which the temperature at which the coal was oxidized could be estimated thus giving a possible means of detecting incipient heating.]

Jan 1, 1938

By James P. Bennett

The Bureau of Mines is investigating the acid resistance of ceramic materials to identify construction materials for emerging technology in chemical and metallurgical processes. Eight commercial ceramic materials, were evaluated: two red shale, two fireclay, one silicon carbide, one silica, one carbon, and one high-alumina. Samples were exposed to 10 wt pct H2S04 at 50° C and 10, 30, 50, 70, and 90 wt pct H2S04 at 90° C for time periods of 110 days. Statistically significant changes in cold crushing strength were observed in the silicon carbide and car-bon materials. Weight changes and the leach rate of Al, Ca. Fe. K, Mg, Na. Si, and Ti were also monitored. The most severe corrosion conditions were at 90° C and 30 to 50 wt pct H2S04 for the acidproof and at 10 wt pct H2S04 for the acid-resistant materials. The silica and the high-alumina materials were the most acid-resistant, followed by the higher density red shale and fireclay.

Jan 1, 1986

By W. K. Sawyer

Resistivity, porosity, permeability, and saturation data were obtained on core samples from the Big Injun, Clinton, Gordon, Bradford Second and Third, and Venango Second oil sands and formation factor-porosity relationships were derived using the general form of Archie's equation F = aø-m, where F is the formation factor, ø is the porosity, and a and m are constants that depend on characteristics of the rock. It was found that a and m varied significantly between sands, as did the exponent in the Archie relation I = Sw-n, where I is the resistivity index and S, is the water saturation. The average exponent, n, determined from all data was 50 percent greater at residual oil saturation than at residual water saturation. Samples from each sand exhibited differences in directional resistivity and/or permeability. The Bradford Third sand data showed correlation between resistivity and permeability anisotropy.

Jan 1, 1971

By J. S. Dunning

Recent developments in energy conversion, mining and minerals processing, pollution control, and chemical equipment have placed in-creased demands on heat-resistant alloys. Higher corrosion rates from oxidation, hot corrosion, and sulfidation have increased consumption of materials that contain critical and strategic minerals and in many cases have limited productivity. The Bureau of Mines is conducting re-search on substitute materials having greater resistance to high-temperature corrosive atmospheres above 6000 C compared to austenitic stainless steels such as AISI 304, 316, and 310, with the goal of conserving critical metals such as Cr and Ni. The substitute materials are based on Fe-Cr-Ni-Al compositions. Aluminum additions to Fe-Cr-Ni alloys significantly improve high-temperature corrosion resistance, particularly sulfidation resistance. In the alloy, devised by Bureau researchers, aluminum additions are held in the form of a second-phase precipitate, 8NiAl. Minor additions of Ti, Mn, and Si improve workability.

Jan 1, 1984

By D. L. Yopps

In research conducted by the U.S. Bureau of Mines, platinum-group metal (PGM) flotation concentrate from the Stillwater Complex, MT, was subjected to biooxidation using Thiobacillus ferrooxidans in an effort to break down the sulfide minerals and liberate the associated PGM's for subsequent chemical leaching. Bacterial preleaching oxidized up to 94 pct of the sulfide present, destroyed the PGM-bearing pentlandite [(Ni,Fe)9S8] mineralization, and dissolved most of the nickel in the concentrate. Cyanidation at 80° C proved to be the most attractive chemical leachant, removing 34 pct of the platinum, 76 pct of the palladium, 94 pct of the rhodium, and 97 pct of the gold from the biooxidized concentrate. Research also indicated that increased sulfide oxidation during the preleach phase led to improved PGM recovery in the subsequent chemical leaching phase.

Jan 1, 2010

By S. C. Termes

The Bureau of Mines conducted research on the flocculation of various minerals with insoluble cross-linked starch xanthate (ISX) to determine its potential as a beneficiation technique for low-grade, highly dissem-inated ores and for selective desliming. Covellite, chalcocite, pyrite, pyrrhotite, chalcopyrite, bornite, sphalerite, galena, and molybdenite fines flocculate with ISX. Floc formation, floc size, and settling rate are dependent on pH, with the pH dependence differing for each mineral. Quartz is not flocculated by ISX. Experiments to obtain selective flocculation of sulfides from quartz were attempted. Good selectivity was only obtained for the bornite-quartz system. postflocculation separations resulted in flocculated bornite in grades as high as 92 pet. Evidence is presented that the flocculation of many of the sulfide minerals with ISX may involve covalent bonding of the xanthate group to lattice metal site(s).

Jan 1, 1983

By Liane L. M. Kadnuck

This report summarizes the results of a hydrologic research study conducted by the U.S. Bureau of Mines (USBM) in cooperation with Energy West Mining Co. at the Deer Creek and Cottonwood Mines, near Orangeville, UT. The USBM evaluated hydrologic and overburden failure data to assess the response of local ground water to underground coal mining in single-and multiple-seam conditions. Fourteen springs located over the two mines were investigated in the study along with overburden failure response caused by longwall panel extraction. Spring discharge was compared to climatic variation and time of undermining to quantify response to undermining. Spring discharge had been reduced owing to below-normal precipitation during the period evaluated. The response of springs to mining in the vicinity was influenced in part by the thick overburden present at the study site the presence of hydrophilic clays and mudstones in the overburden stratigraphy, and elevation of the springs above mine level, which buffered the effects of undermining.

Jan 1, 1994

By Yael Miron

Two recent unplanned detonations occurred during blasting operations in sulfide-bearing ores in a Nevada gold mine. Other premature detonations have also reportedly occurred at other Nevada, California, and Arizona operations within the past few years, with increasing frequency. Unplanned or premature detonations can be extremely hazardous to life and can cause extensive property damage. A miner was injured in one of these occurrences. This report, by the U.S. Bureau of Mines, is intended to acquaint personnel involved in such mining activities with the basic causes for these accidents. These causes include the exothermic oxidation of pyrite (FeS2) and formation of ferrous sulfate (FeS04), the exothermic and energetic reaction of the ferrous sulfate with ammonium nitrate-fuel oil (ANFO)-based explosives, and the associated elevated temperatures that can set off detonators and explosives in the boreholes. Recommendations for safe operation by the Mine Safety and Health Administration, the Bureau, and the mine involved with the recent incidents include monitoring temperatures in the blast holes, analyzing for sulfate and ferrous ions, and limiting the time between loading and firing in accordance with conditions in the blast holes. Other procedures for safe operations should fit specific conditions in, the mines.

Jan 1, 1992

By D. W. Frommer

Mineral dressing research was conducted by the Federal Bureau of Mines under a cooperative agreement with the St. Joseph Lead Co., on three samples of iron ore from the Pea Ridge deposit in central Missouri. The objective was to provide information on how to upgrade these submarginal ores and produce marketable concentrates. Samples were prepared from drill-hole cores of similar composition and character to produce (1) a medium-grade mixed hematite and magnetite, (2) a high-grade mixed hematite and magnetite, and (3) a high-grade magnetite. In all three ores phosphorus and sulfur constituted objectionable impurities; excessive amounts of silica were also present in the medium-grade ore.

Jan 1, 1960

By G. S. Scott

[In the course of the investigation the Bureau of Mines is carrying on to determine the causes, behavior, and control of mine fires, the detection of incipient heating underground in the mines and above ground in refuse banks has received consideration. A report has been puplished5/ describing apparatus and tests made on anthracite to determining the amount and composition of the oxidation products when normal dry air was passed through it at temperatures varying from 100° to 350° C. These tests showed that the amount of evolved gases and their relative prorortions varied with the temperature. From: these results, graphs were prepared by which `he temperature at which the coal was oxidized could 'be estimated, thus giving a possible means of detecting incipient heating.]

Jan 1, 1938

By R. E. Green

The Bureau of Mines undertook a bench-scale study of three different types of oxidized taconites3 from the Lake Superior district to improve the dispersion-selective flocculation-desliming process for beneficiating these materials. The response-surface contours of the effects of dissolved ionic species in the water and of three dispersion systems on the selective flocculation process were studied. Results of metallurgical data and chemical analyses of the aqueous phase showed that the water quality affects the performance of the selective flocculation process.

Jan 1, 1984

By H. J. Lechtenberg

This Bureau of Mines report investigates solvent injection as a means of increasing oil production from low-gravity oilfields; thus, wells in two California oilfields that produce from reservoirs having low-gravity oil were injected with highly aromatic solvents to increase their oil recovery. The wells were either allowed to soak or the solvent was circulated for a period of time. In some of the wells, the solvent was followed by a slug of water. The post-stimulation production rate was considerably higher than the prestimulation rate of the wells. Wells in which the solvent was not followed by water showed an immediate increase in oil production, and essentially all of the solvent was recovered. The wells in which solvent was followed by water essentially showed a delay in the increase in oil production, thus indicating a temporary water block. The results show that the production rate is usually increased by the injection of solvent, and the method may prevent early abandonment of marginal producers. Cumulative post-stimulation oil production indicates that cyclic solvent injection treatment can be an economic success.

Jan 1, 1974

By James L. Eirls

The objective of this project was to improve a driver's field of view for large trucks used in the mining industry. Rearward viewing was enhanced by improving the rear-view mirror designs. Rear vision was accomplished using a closed circuit television system. Views ahead,, to the right, and downward were obtained with a blind area viewer (BAV). The BAV is a unique combination of fresnel lenses housed in a shielded, environmentally protected enclosure that produces an image of the area in front of and downward 70° and to either side of the BAV 300. The improved visibility devices were evaluated by long-term, in-mine testing. The right Bide mirror (RSM) and BAV provide the greatest improvements for the least cost and are commercially available. Application of the RSM and BAV should achieve a reduction in accident potential and greater vehicle productivity by enlarging and improving the equipment operator's visibility and making priviously blind areas and hazardous situations detectable.

Jan 1, 1982

By Brian T. Brady

The year 1992 recorded unimpressive economic growth and uncertainties over what changes would occur for the financial market. Falling interest rates in the United States and elsewhere tended to exert a number of positive influences on financial markets and, indirectly, the mining and quarrying industry. The interest rate declines during 1992 were no exception. Lower rates prompted many investors to turn their attention to long-term investments such as stocks that offer potentially greater rates of return, causing large cash inflows into the equity market. Lower rates made it easier for businesses to finance growth and for consumers to finance the purchase of products businesses made. Also the rates enabled many companies to increase their health and profitability by refinancing their existing loans at lower rates. Falling interest rates were not confined to the United States. With Japan and Western Europe in the midst of economic slumps, marketing authorities in many countries overseas lowered rates in an effort to stimulate business activity. True to form, that contributed to stock market rallies abroad. Stabilizing inflation and lower interests stimulated the industry during 1992 and will likely influence favorably the industry for the next few years.

Jan 1, 1992