Search Documents

By E. C. Baker

The capital investment and operating costs of two methane-control systems used during longwall mining operations are compared in this Bureau of Mines report. Costs are given for a surface gob hole drainage system and an underground cross-measure borehole drainage system to control methane gas in gobs in four coal mining areas--central Pennsylvania, northern West Virginia, southern Virginia, and northern Alabama. Present-worth analysis is used to determine the more cost-effective alternative in each location. The alternatives have equal lives and provide the same service based on a minimum rate of return of 15 pet. In central Pennsylvania and northern West Virginia, the gob hole system is more cost effective than the cross-measure system, by 10 and 18 pet, respectively. In southern Virginia and northern Alabama, the cross-measure system is more cost effective, by 29 and 38 pet., respecitively. Costs for other locations must be developed on a case-by-case basis.

Jan 1, 1988

By A. M. Evans, J. H. Soulé

"INTRODUCTION Deposits of iron ore in Cherokee County, Tex., have been worked at various times in the pact, and the ore has been smelted in small local blast furnaces.Recently it was proposed to establish a charcoal blast furnace with a wood distillation plant to produce charcoal for fuel and byproducts. Financial assistance from the Reconstruction Finance Corporation was sought by George Easley and associates to enable them to purchase, move, and erect the furnace and build the required accessory plants. The furnace was to be moved from Pembroke, Fla.In August 1941, the Bureau of Mines was asked by the Office of Production Management to check the development work of Easley and associates and to ascertain (1) the iron-ore reserves, (2) the cost of mining ore and delivering it to the blast furnace, and (3) the grade and character of the ore. The Bureau of Mines was advised, while the investigation was in progress, that approximately 1,000,000 long tons of measured reserves would be sufficient to demonstrate the feasibility of operating the properties.Although deposits of iron ore are widely distributed in Cherokee County, only the Pryor Mountain, Banks and Cherokee, J. P. Acker, and Citizens State Bank tracts were sampled thoroughly by the Bureau of Mines. The iron-ore rights on these are owned by the New Birmingham Development Co., the Cherokee Development Co., or by individuals. Options to lease the ore rights were obtained by Easley, who obtained options on the Hawes Peach Orchard and Bradford tracts, also, which were examined only cursorily by the Bureau."

Aug 1, 1947

By John C. Franklin

Water-based epoxy sealants were examined during a 2-year period to deter-mine their effectiveness as barriers to radon release in uranium mines. Radon emanation rates from uranium ore samples were monitored for extended periods in the laboratory before and after sealant application. Reduction of radon flux due to the coating of laboratory samples was approximately 80 percent. Test chambers in a dormant uranium mine were monitored to determine both short and long-term barrier effectiveness. These field studies of the seal-ants indicated radon flux reductions exceeding 50 percent relatively soon after application and nearly 75 percent about 1 year later. An unexpected complication to early monitoring in the form of a large radon emanation increase, believed due to added moisture, is discussed.

Jan 1, 1977

By N. S. Dalal, V. Castranova, X. Shi, W. Wrr, V. Vallyathan

"SUMMARY Data presented here indicate that freshly fractured silica exhibits surface characteristics and biologic reactivity distinct from aged silica, and on this basis we propose that these surface features may lead to enhanced manifestations of lung Injury. Grinding of silica produces ~10"" Si and SI-O (silicon-based) radicals per gram of dust on the particulate surface which are characterized by an electron spin resonance (ESR) spectrum centered around g = 2.0015. These silicon-based radicals react with aqueous media to produce OH radicals, which are demonstrable using a DMPO spin trap. The concentration of silicon-based radicals in silica decreases with aging in air and exhibits a half-life of ~30 h, whereas its ability to generate OH radicals in aqueous solution decreases with a half-life of ~20 h. However, on storage in aqueous media, the concentration of silicon-based radicals end the dust's ability to generate OH radicals decrease significantly within a few minutes. Freshly ground silica is also more biologically reactive than aged silica, because freshly crushed silica activates a greater respiratory burst In alveolar macrophages than aged silica, i.e., storage of ground dust in air decreases silica-Induced superoxide anion secretion, hydrogen peroxide release, and NBT reduction by 25%, 68%, and 43%, respectively. Furthermore, compared to aged silica, freshly ground silica exhibits a greater cytotoxic effect on cellular membrane Integrity, i.e., a 1.5-fold increase in LDH release from macrophages, a 36-fold increase in hemolytic activity, and a three-fold increase in the ability to induce lipid peroxidation. Because acute silicosis is frequently associated with occupations in which freshly fractured crystalline silica of respirable size is generated, the present study suggests that fracture-generated silicon-based radicals may play a significant role in the pathogenesis of this disease. AM REV RESPIR DIS 1955; 133:1213-1218IntroductionOccupational exposure to crystalline silica can be associated with either chronic or acute pulmonary disease. Chronic silicosis becomes manifest 20 to 40 years after first exposure and is characterized by development of concentric hyalinized nodular lesions in the lung with the de-velopment of dyspnea over a period of several decades. Acute silicosis, on the other hand, is manifested by a rapid on-set after exposure and is characterized by the accumulation of an amorphous granular lipoprotein exudate in the airspaces and rapid development of respiratory disability within a few years (1-3).Information is growing concerning the etiology of chronic silicosis. Studies sug-gest that several mechanisms may be in-volved in the development of fibrosis. Lung injury may result from silica-induced release of lysosomal enzymes from alveolar macrophages (4, 5). In ad-dition, silica-induced activation of su-peroxide anion and hydrogen peroxide release from alveolar macrophages may result in oxidant-induced damage to lung parenchyma (6). Silica exposure can also result in the release of mediators from alveolar macrophages which enhance the proliferation of fibroblasts and the syn-thesis of collagen by these pneumocytes (7, 8)."

Jan 1, 1988

By S. C. Rhoads

The Bureau of Mines is investigating low-chromium alloy substitutes for type 304 stainless steel (type 304 SS). The purpose of the research is to reduce the chromium content in austenitic stainless steels used for corrosion-resistant applications. Nine Fe-9Cr-12Ni alloys containing additions of 0 to 5 pct Mo, 0 to 2 pct V, and 0 to 2 pct Cu were selected for evaluation. All of the experimental alloys containing 5 pct Mo and an alloy containing 2Mo-2V-2Cu possessed structure and tensile strengths similar to those of type 304 SSe Alloys containing SMo-2V and SMo-2V-2Cu had ac-ceptable welding properties as measured by the Varestraint test. Alloys containing at least 2 pct Mo had cQrrosion resistance comparable to that of type 304 SS in solutions of nitric acid, phosphoric acid, acetic acid, and citric acid. In chlorides, all the experimental alloys were susceptible to localized corrosion and stress corrosion cracking similar to that of type 304 SSe The corrosion properties were established by weight-loss tests, electrochemical polarization tests, and stress-corrosion cracking tests. An Fe-9Cr-12Ni-SMo-2V alloy and an Fe-9Cr-12Ni-SMo-2V-2Cu alloy had a combination of welding properties, tensile properties, and corrosion resistances that were most comparable to those of 304 SS.

Jan 1, 1984

By C. E. Jordan

The Bureau of Mines is conducting research into the pneumatic recovery of coarse mica and has used this method to produce mica concentrates that contain more than 90 percent mica. This research is being carried out pursuant to the Bureau's objective to develop technology that will help maintain an adequate supply of minerals and metals to meet national economic and strategic needs. Researchers used a Bureau-designed system of crushers, screens, and zig-zag air classifiers to concentrate coarse liberated mica particles from mica-bearing materials. This pneumatic system was used to concentrate four mica ores from Arizona, North Carolina, and South Dakota and three waste tailings from Alabama, Georgia, and South Dakota. Using these samples, it was demonstrated that plus 65-mesh size mica can be effectively recovered by the pneumatic method. Not only were the concentrates high in mica content; it was also demonstrated that this method can be used to recover up to 78 percent of the mica that was originally contained in the samples. Because it is a dry concentration method, the pneumatic beneficiation technique may be advantageous in areas where water resources are limited.

Jan 1, 1980

By J. M. Stuve

Low-temperature heat capacities and the enthalpy of formation were deter-mined calorimetrically by the Bureau of Mines for CuO?CuS04. The derived standard entropy (S°298.15) was 40.36±0.04 cal/deg-mole, and the enthalpy of formation (?H°f) was -219.l±0.3 kcal/g-mole. A large thermal anomaly was observed in the heat capacity of CuO?CuS04 at 20±0.1 K. Gibbs energy of formation data are tabulated up to 1,200 K. Construction details of a precision low-temperature adiabatic calorimeter capable of determining heat capacities of solids in the temperature range 5 to 320 K are given. A calibrated miniature germanium resistance thermometer was incorporated into the calorimeter to extend the range of accurate measurements below 15 K. High-resistance dc heater windings were used throughout the cryostat to reduce heat conduction of inner connecting wires.

Jan 1, 1975

By Grant Buma

Groundwater restoration is an uranium leaching. Information on the technology, costs, and the current permitting regulations is of vital operators and to firms considering in important aspect of in situ effectiveness of the current state and federal government importance to in situ leach situ leaching. This study, funded by the U. S. Bureau of Mines, describes: (1) all recent restoration attempts at commercial in situ leach operations, (2) restoration costs reported by the industry, (3) empirical equations that predict the amount of groundwater flushing required to meet the current restoration criteria, and (4) in situ uranium permit requirements for the states of Texas, Wyoming, New Mexico, Utah, Montana, Colorado and South Dakota, and Federal requirements.

Jan 1, 1981

By R. C. Hickman

"INTRODUCTION Marl, consisting of a bed of coarse shell conglomerate from 1 to 5 feet thick, occurs on the Chesapeake Corporation tract and Philbates properties in New Kent County, Va.Nine holes were drilled on these properties in February 1946. ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts prelimi¬nary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.The project was under the immediate supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch.LOCATIONThe Chesapeake Corp. deposit is reached from West Point, Va., by driving west on State Route 33 to the junction of State Route 634, approximately 5 miles. Proceed southeast along State Route 634 about three-quarters of a mile, at which point an old longing road turns north along a ridge and leads to the marl outcrops about one-half mile distant. The Philbates property lies three-quarters of a mile farther west along State Route 33 from the junction with State Route 634. The property lies north of State Route 33 and east of State Route 623 (fig. 1). The marl deposits are on the north end of the farm. The Chesapeake Corp. tract comprises 174 acres and the Philbato property 58 acres."

Aug 1, 1947

By J. R. Thoenen, B. H. Clemmons, A. H. Reed

"INTRODUCTION AND SUMMARYOverall red-ore reserves in the Birmingham, Ala., area were estimated in 1910 by E. F. Burchard 4/. Since then mining has progressed into areas classed by Burchard as ""unavailable for exploitation"" under conditions existing at that time. This is understandable when it is considered that red iron ore was valued at $1.19 a gross ton at the mine in Birmingham in 19102/ and by 1948 had risen 300 percent; 6/ that skips had replaced cars in slope haulage; that mechanical loading and rubber-tired haulage had replaced hand loading and mule or locomotive haulage; and that other more efficient mining methods had been introduced. Intensive study during the intervening 40 years has been given to ways and means for upgrading the low-grade ores in the area and combining or blending them with raw red and brown ores for improved blast-furnace feed.It is reasonable to expect that future progress in mining efficiency and increased knowledge of the beneficiation characteristics of marginal ores will permit extraction of red-iron minerals now considered uneconomic.The Bureau of Mines has undertaken to restudy iron-ore reserves of the Birmingham area to determine what tonnage and grades of mineral are present; what is necessary to make them amenable to mining; what further advancement is possible in beneficia¬tion methods; and where increased production may be obtained in the area if and when required. This study has been underway for the past 2 years, but research into the beneficiation of marginal ores has been in progress at the Southern Experiment Station for the past 30 years. Many results of that research have been adopted in commercial practice in the area. Other results have not been published but are pre¬sented here in condensed form as an important factor in assessing marginal deposits with respect to their importance as ore reserves.An interim discussion of the salient features of past history and progress, as well as the data developed during the years of research in beneficiation at this station and the present field investigation, will make for a better understanding of the present position as well as be useful in evaluating future potentialities. Discussion in this paper is confined to the main Birmingham Basin area, which contains the largest concentration of hematite ores in the district."

Jul 1, 1953

By John D. Rockaway

Failure of the mine floor supporting coal pillars frequently occurs when the subcoal strata include "underclays" or other low strength strata. The failure process has been studied to define the response of these materials to applied coal pillar loads and to determine the applicability of bearing capacity analysis to evaluate unsafe conditions. The study has been accomplished through an investigation of both the intact and insitu geotechnical properties of the subcoal strata and through the installation of floor movement monitoring instrumentation. The results of these studies have indicated that both the shear strength of the underclay and the stratigraphy of the subcoal strata must be considered in the analysis. The shear strength was the major controlling factor determining the ultimate load carrying ability of the materials, but the thickness and stratigraphic position of the weak layers influenced the mechanism of the failure process. The methods of bearing capacity analysis were used to define pillar stability that included provisions for taking into consideration a two-layer system. Conditions assumed for a coal mine where a weak underclay overlies firmer strata. The results of the analysis compared very well with observed mine conditions, indicating marginal conditions in areas of the mine which later experienced pillar support failure. In addition, a "heave factor" was derived to predict potentially unstable floor conditions in the mines studied in detail.

Jan 1, 1979

By McHenry Mosier

This progress report on a national survey of the use of detachable bits in metal mines covers 10 mines. It presents comparative costs for drilling with conventional and detachable bits, describes the reconditioning of drill steel, and gives various data on rock drilling at these particular mines. Reports to follow will include similar data on drilling at other metal mines in the United States. ACKNOWLEDGMENTS This report is based on costs and data developed and furnished by the operators of the mines visited. The author is greatly indebted to the officials and staff members at these mines for their cooperation and assistance.

Jan 1, 1936

By D. H. Hileman

Economic investigations indicate that bituminous coal can be mined underground in the Uinta region and marketed at a cost competitive with that of other energy sources in the West. A selling price of $3.90 per ton of coal was calculated from a cost analysis of a projected coal mine in the Emery coal- field of Utah. Although mines in some of the coalfields have extremely difficult mining conditions and cannot compete in the energy market at this price level, at least two other coalfields in the Uinta region contain coal reserves that could be mined and sold at a price of approximately $3.90 per ton. Projections by power companies and other coal-consuming industries indicate a strong future market for the large coal reserves in the Uinta region.

Jan 1, 1970

By S. L. May

Procedures for separating columbium and tantalum have been developed by the Bureau of Mines as part of a broad research program on the utilization of low-grade ores of columbium and tantalum, Columbium and tantalum compounds of greater than 99 percent purity have been obtained by application of the solvent extraction separation system: Hydrofluoric acid-sulfuric acid-methyl iso-butyl ketone. This system is unique in that it not only separates columbium from tantalum, but also separates these two metals from other metallic impurities. The system is effective for separating the metals irrespective of the tantalum and columbium ratio of the starting materials. Investigations in which the spent feed obtained from the initial coextraction step was recycled to the system indicated that efficiency was increased, and cost was reduced without impairing product purity. Continuous tests demonstrated that this solvent extraction system could be used in large-scale equipment without loss in efficiency or in purity of products. The separation of columbium and tantalum has been difficult because of the similarity in their chemical bahavior. Many methods have been proposed for separating these two elements, but most methods either did not achieve satisfactory separation or were tedious and time consuming. The Marignac process (3, 4)4 developed in 1866 was the only method used commercially until recently. This separation procedure is based on the difference in solubility in aqueous solution of potassium tantalum fluoride and potassium columbium oxyfluoride. Current commercial practice appears to favor solvent extraction as a method for separating tantalum from columbium (1). Several efficient methods for separating columbium from tantalum by solvent extraction (2, 9, 8) were reported earlier from this laboratory.

Jan 1, 1961

By R. E. Heithecker

[The principle of determining volumes of liquid by alternately drawing in and discharging given quantities of the fluid from a confined space or compartment of known volume and mechanically counting the number of displacements is well established. This is true particularly in water measurement. For several years, oil meters employing the same basic principle have beer, used for gaging oil production from individual wells, groups of wells, and in some areas for metering the entire production from a property. Especially in areas where there is town-lot drilling and space for tankage in at a premium, oil meter have been used successfully to gage the oil. This facility has obviated the necessity of installing gage tanks. Oil meters also have been used in pip-line and refinery operations and in loading tankers. Present knowledge of the subject shows that positive-displacement oil meters can be used for measuring crude oil in the field and elsewhere, provided the meter-counter mechanism is in proper adjustment and the oil has been studied sufficiently to determine the proper factor to be applied to the volume as registered by the meter, making possible the adjustment for the shrinkage of the oil caused by liberation of gas from solution.]

Jan 1, 1938

By Edward L. McHugh

The appraisal of mineral resources of the Challis National Forest, Idaho, by the U.S. Bureau of Mines, was made so that the mineral resources of the forest could be appropiately considered in land use planning. Information from this study is intended to tip the U.S. Forest Service to incorporate mineral resource data into forest plans The study was done in conjunction with the U.S. Geological Survey, which released a companion report on the geology and mineral potential of the Challis National Forest in 1989. This summary report is derived from a more detailed USBM Open-File Report (MLA 6-91) that includes descriptions of mines and prospects, commodity profiles, and development cost models. Since the 1860's mines within the Challis National Forest have produced mineral commodities worth more than $590 million at current (1989) commodity prices. Identified mineral resources have a gross value of about $2 billion at current prices, including 8 strategic or critical minerals. The U.S. Bureau of Mines study identified and described 723 active and inactive mineral properties within the forest. Mineral properties with identified resources were evaluate to determine their economic significance, and an assessment was made of the feasibility of mineral development. Of the 2,516,191 acres in the Challis National Forest, about 390,000 acres were classified as having mining development interest. Commercially important mineral production, mainly of molybdenum, gold, and silver from the Challis National Forest is likely for the foreseeable future.

Jan 1, 1991

By L. C. IlsLey, J. W. Paul, E. J. Gleim

Flame safety lamps have been used in gaseous mines since the Davy lamp was introduced, more than 100 years ago. During the last decade the flame safety lamp has been rapidly replaced by the electric lamp as a device for illuminating the miner's working place; in the United States the electric cap lamp has been widely adopted. For example, in 1911 approximately 45,000 flame lamps and no electric lamps were being used in the Pennsylvania bituminous mines, which were then producing 35 per cent of all the soft coal mined in this country; by 1918 the flame lamps had decreased to 17,000, whereas electric lamps-mostly of one maketotaled nearly 48,000. In Great Britain during the same years the total of 723,934 flame lamps decreased to 590,185 and the electric lamps gained rapidly from 4,298 to 156,521. No later reliable figures are at hand. However, before the flame lamp becomes obsolete, it is fitting that the Bureau of Mines compile a permanent record of a device which has served the mining industry for more than three generations, and not only made possible the development of entire districts that otherwise could not have been worked but undoubtedly saved the lives of thousands of underground workers. Flame safety lamps are capable of doing more than the name indicates. First, under normal conditions, they can be used in a mine atmosphere that contains an explosive mixture of gas and air without great danger of exploding such a mixture, though such use of a flame lamp should not be permitted. Second, to an experienced man they indicate percentages of gas much lower than the explosive limit, and thus can be used to indicate to workers the approach of an unsafe condition in the mine atmosphere. Third, flame lamps will not burn in an atmosphere greatly deficient in oxygen, and they therefore warn the users of such deficiency in time to withdraw to a place of safety. Flame safety lamps are still used rather widely in the United States for general illumination and to a still greater extent for detecting gas. Many coal-producing States require fire bosses to use these lamps in gaseous mines, and the regulations of several States specify that a gIven number of such lamps be kept available for emergency service.

Jan 1, 1924

By F. E. Cash

Among petroleum refinery employees and officials throughout the United States there has been marked effort to reduce accident frequency and severity. For the interest and benefit of refineries both in Louisiana and in other petroleum-refining States it has been possible to obtain from five refineries, representing 70 per cent of the production of Louisiana, tae accident experience for the past 3 to 6 years. The companies concerned have requested that their names be not used. For tide reason the four plants listed and discussed are designated as refineries A, E, C, and D. The size of the plant as regards largest to smallest number of employees is indicated by the alphabetical order.

Jan 1, 1933

By Oliver Bowles

The manufacture of lime is one of the oldest industries. Plants are distributed widely and furnish an essential raw material for numerous industries. The use of lime by the building trades, in agriculture, and in hundreds of manufacturing and chemical processes has created demands for a large production and has necessitated exhaustive research on methods of manufacture and uses. The bibliography of lime is an extensive one, but for the most part each publication has dealt with only certain operations. The purpose of this paper is to present a general picture of the industry as a whole. The abundant literature has been abstracted and quoted freely, and the National Lime Association has rendered valuable assistance in furnishing data for certain sections. Publications containing more detailed information on the various branches of the industry are referred to in the footnotes and in the bibliography.

Jan 1, 1936

By S. J. Hussey

Since the discovery in 1935 by Adams and Holmes that certain synthetic resins exhibit ion-exchange properties, many applications of the ion-exchange process have been made. There are two general types of ion-exchange resins. Cation exchange resins adsorb cations from solution, and these in turn may be replaced by other cations adsorbed under certain conditions. 'Anion exchange resins adsorb acids from solution, and the anion of the acid may then be replaced by other anions. It is reported, however, that certain anion exchange resins have a low capacity for anions of weak acids without the necessity of acid adsorption either directly or as an intermediate step. The adsorbed ions may then be removed from the resins by elution with an appropriate solution, and the resin is prepared for the next adsorption cycle by regeneration with another solution. Sometimes one solution, is used to simultaneously perform the functions of elution and regeneration. The first and probably the largest application is in the field of water purification. Other applications have been made in the production of high-quality foods for human consumption, in the recovery of valuable substances from solutions, in the separation or fractionation of electrolytes, and in several other fields, each of which has its specific applications, variations, and possibilities. Ion exchange resins also have been highly useful in perfecting techniques of laboratory analysis and research.4/, 5/, 6/

Jan 1, 1948