Search Documents

By Peter F. Steidl

As part of the Bureau of Mines methane control program, the Upper Free-port coalbed was studied in Fayette County, Pa., where this coalbed lies about 650 feet below the Pittsburgh coalbed and contains the largest remaining reserves of any coalbed in the county. Coal and overburden isopachs, structure and joint pattern maps, and a fence diagram were prepared using data from gas and oil exploration logs and coal outcrops. These maps will aid in deter-mining the need and/or feasibility of degasifying the Upper Freeport coalbed in the study area. Much of the coalbed in this area is under 600 to 1,400 feet of overburden. By correlation with data from the Pittsburgh coalbed, the gas content at depths of this order is estimated to be between 140 to 300 cf/ ton of coal, for a total of 190 to 400 billion cubic feet of methane in this coalbed in Fayette County.

Jan 1, 1977

By D. H. Chambers

Digestion studies were undertaken to develop a method for the rapid dissolution of high-temperature ferroalloy scrap. Laboratory tests showed: (1) dissolution of alloy scrap with ferric ion as the leaching agent was a moderately rapid method of digestion; (2) the dissolution process can be considered as a typical reaction of a metal with chlorine gas, although evidence was obtained to show dissolution as a two-step process, one step as the reduction of ferric ion by the soluble alloy constituents and the other as the oxidation of ferrous ion with chlorine gas; and (3) the attack of ferric ion on the alloy was a function of alloy composition, ferric to ferrous ion ratio, and area of contact between leach solution and alloy. The exceedingly complex nature of alloy compositions and dissolution products generally precluded satisfactory analytical determinations. Results of moderate accuracy were obtained using complex modifications of standard analytical and spectrographic techniques.

Jan 1, 1968

By Robert F. Randolph, Dana C. Reinke, Richard L. Unger

Purpose The NIOSH Hearing Loss Simulator is a software training and communication tool for promoting hearing loss prevention. It allows a user or trainer to demonstrate the effects of noise exposure on hearing without experiencing an actual noise-induced hearing loss. Estimates of the effects of different levels of noise exposure are based on the American National Standard Determination of Occupational Noise Exposure and Estimation of Noise-Induced Hearing Impairment, otherwise known as ANSI S3.44. This standard specifies the predicted hearing loss for noise-exposed populations of individuals based on risk factors that include gender, age, sound levels (in A-weighted decibels or dBA), and years of exposure. Algorithms specified in the standard were derived from empirical studies of populations that had no exposure to loud noise and other populations that had experienced various levels and durations of noise exposure. This manual explains the major objectives that can be addressed with the simulator and training scenarios that can be applied to real-life, real-worker scenarios. The majority of this guide explains the simulator's functions in detail. Simulator users are encouraged to read this manual while learning how to run the software. [ ] Training Objectives The main objective of the Hearing Loss Simulator is to increase motivation for taking effective hearing prevention action by demonstrating simulated noise-induced hearing losses. [The Simulator can also help teach the following facts about hearing loss. Hearing loss is affected by noise levels. Hearing loss worsens as the noise exposure duration increases. Hearing loss can become permanent. Hearing loss makes it harder to hear what others say. Most hearing loss is not caused by age. Speech is made up of both low and high pitch sounds. Hearing loss due to noise makes it harder to hear high pitch sounds. Hearing loss due to noise has less of an effect on hearing low pitch sounds.]

Jan 3, 2008

By Seth C. Schaefer

As part of the Bureau of Mines, U.S. Department of the Interior, effort to provide thermodynamic data for the advancement of minerals technology, the Gibbs energy of formation of sphalerite (zinc sulfide) was investigated with a high-temperature galvanic cell employing stabilized zirconia as the electrolyte. In the temperature range 948 to 1,210 K, potential measurements were obtained for the cell Pt, ZnS + ZnO, S02 = 1 atm // Zr02 // Cu20 + Cu, Pt, with the overall cell reaction ZnS(c) + 3 Cu20(c) = ZnO(c) + 6 Cu(c) + S02(g). (1) These results, combined with the best available values of ?Gf° for ZnO, S02, and Cu20 from the literature, give the Gibbs energy of formation of zinc sulfide for the reaction Zn(l,v) + 1/2 S2(g) = ZnS© (2) ?Gf° = -64.223 + 24.02 X 10-3T ± 0.650 kcal/mole (3) (948-1,180 K; standard states - pure liquid zinc and S2 gas at 1 atm), and ?Gf° = -92.720 + 48.17 X 10-3 ± 0.650 kcal/mole (1,180-1,210 K; standard states - pure zinc vapor and S2 gas at 1 atm). A third law analysis yields for the formation reaction Zn(1) + 1/2 S2(g) = ZnS(c), (5) a standard enthalpy of formation as follows: ?Hf298.15 = -63.64 ± 0.700 kcal/mole.

Jan 1, 1978

By Paul T. Allsman

THIS CHAPTER reviews the highlights of developments in mining technology during 1956 and presents a special report on the design of mine openings in stable ground. This special report is presented each year in an endeavor to stimulate use of the scientific approach to the solution of problems related to mining technology. Assuming that the literature on mining technology reflects trends in mining, it appears that two areas of activity were given most attention in 1956. One was research on mining technology,4 and the other was improvement of transportation, particularly trackless transportation, both at surface and underground mines.

Jan 1, 1958

By Syd S. Peng

The design of retort interchamber pillars is important in determining surface stability over in situ retort mines and to the health and safety of miners, particularly with respect to possible escape of heat and toxic gases from retort chambers. Stress distribution in retort interchamber pillars, roof, and floor was examined with the aid of linear, finite-element analysis using data from experimentally determined mechanical properties. Properties determined included elastic moduli, strength, and creep constants in laboratory tests on core covering a 100-foot depth interval in the oil shale from the Piceance Basin in Colorado. The most critical stress concentration was found in the rib side of the interchamber pillar at a height above the floor line of 1.25 times the width. Guidelines for pillar design that consider pillar strength, creep, and retorting temperature effects are proposed.

Jan 1, 1981

By J. E. Tiffany

"The new permissible blasting device, Cardox, utilizes as a blasting agent liquid carbon dioxide which is discharged.as a gas from a steel container or shell. The loaded shell is placed in a borehole, stemmed, and tamped in a manner similar to that employed with explosives, and is fired by electricity.The Bureau of Mines' approval for use of the device in coal mines was granted as Approval No. 1 under date of October 3, 1928; as the result of tests made under the conditions and requirements of Schedule 20. There have been three subsequent extensions whereby minor modifications in the original design were granted.The permissibility of the device is subject to the following conditions; (1) It shall be in all respects similar to the sample submitted for tests; (2) certain thicknesses of disc and. weights of heater ingredient and of carbon dioxide, all of which are set forth in Table 2 under the provisions governing permissibility, must be used: (3) the rear cap must always be in place after the shell has been charged, to prevent accidental firing; and (4) firing must be done by means of a permissible-type blasting unit.The permissibility of Cardox was established by gallery tests similar to those used in testing explosives for permissibility. In these tests the shell was discharged into gallery 1 without causing any ignition of gas and air or of gas, dust, and air mixtures there. The conditions of charging the shell, such as weight of the ingredients of the heater element, the carbon dioxide charge, and thicknesses of the disc, were varied according to the conditions under which it would be likely to be used in blasting. The tests made in gallery 1 are here described in detail, as are also the tests which have been made for determining the propulsive strength of the device and the quantities of poisonous gases given off when a shell is discharged."

Mar 1, 1929

Develop technology that can reduce the dust exposure of a mine worker at the tailgate end of the longwall face by providing him with a clean split of air. Approach Use the jet spray air mover (JSAM) developed under a Bureau of Mines contract (refer to Technology News No. 117 for details on the development), to clean a small portion of the face air and to discharge the clean air behind a brattice partition. How It Works At most longwalls, air flows along the face from head-to-tail. Most of the airborne respirable dust generated along the face during mining is transported to the tailgate with the airflow. Any miner required to work at the tailgate is exposed to this dust. The only practical means of removing airborne respirable dust is with a scrubber. Simplicity and size made the JSAM the best choice for cleaning a portion of the tailgate air. The scrubber has no moving parts and is operated by water at low flow rates (<10 gpm) and fairly high pressures (250-500 psig). Many longwalls have sufficient water systems to supply the JSAM with adequate water pressures and flow rates. Also, the JSAM&apos;s size (4&apos;x 2&apos;x 1&apos;) allows it to be hung on one of the tailgate&apos;s shields or at some other convenient location. A clean split can be maintained at the tailgate by discharging the cleaned air behind a brattice partition at the work area. This should effectively seal off the clean air from the dusty air and provide the tailgate worker with a less dusty work environment.

Jan 1, 1983

By Daniel Edelstein

Demand for arsenic trioxide dropped markedly during 1983, primarily as a result of a 27% reduction in cotton planting. As an oversupply of arsenic trioxide developed, prices declined for both domestic and imported material. Domestic Data Coverage.-Commercial-grade arsenic trioxide and arsenic metal were produced by only one U.S. company, which voluntarily reported its production to the Bureau of Mines. To prevent disclosure of proprietary data, the production data have been withheld.

Jan 1, 1984

By Paul B. Harder

Round Mountain Gold (RMG) in cen­tral Nevada, reports that over a nine-year period and a million operating hours, its fleet of 150-ton and 190-ton haul trucks has averaged better than 93% availability, with some of the trucks approaching 70,000 operating hours. Repair costs have been far below industry averages. Mine operations manager Pete Kesl credits the high availability and low repair costs to a succession of Product Support Agreements between RMG and Caterpillar dealer Cashman Equipment. He adds that good equipment and a high level of trust and co­operation between all parties to these agreements have been essential to their success at Round Mountain.

Jan 1, 1998

By Charles Vaught

This is the second in a series of four articles that discuss underground firefighting preparedness. As with the first article in the May-June issue, it is based on interviews with 214 miners conducted at 7 underground mines (?A? through ?G?) by researchers of the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Center [Vaught et al. 1996].In the first article, the authors presented an overview of the study conducted by NIOSH on mine fire response preparedness and provided a general perspective on underground mine fires. In this article, we will describe miners? preparedness to evacuate a fire and their experience with incipient fires.

Jan 1, 1997

By J. E. Dooley

Reference mass spectra and analytical correlations for 20 alkylcycloalkyl sulfides and two dicycloalkyl sulfides are presented &apos;to provide information that will facilitate the identification of sulfur compounds occurring in natural or synthetic mixtures. Reference spectra indicate relative intensities in addition to parent and base peak sensitivities. Analytical correlations establish the ionic species that reflect major fragmentation paths for the com-pounds studied. Specifically, the correlations show that base peaks are formed by several different processes: (1) Cleavage of the bond a to the ring, (2) fragmentation of the alkyl chain, and (3) fragmentation of the ring plus fragment contribution from the alkyl chain. Useful correlations for deter-mining alkyl chain length involve the CnH2+3S+ and CnH2n+1 + ions. CnH2n-2+ and CnH2n-1 S+ ions reveal the number of carbon atoms in the cyclic ring. Other important ionic species are also discussed.

Jan 1, 1970

By Joseph Cervik

Gas occurs in coalbeds in an adsorbed and a free gas state. Adsorbed gas is stored in the micropore structure and its transport is governed by Fick&apos;s law. The free gas occurs in the fracture system and flows according to Darcy&apos;s law. These two modes of mass transport are interdependent. Production decline curves of coal-gas wells are of the constant percentage decline type and, thus, show no indications of flow characteristics peculiar to coal-gas reservoirs. The effectiveness of surface boreholes as a degasification scheme depends upon both good fracture permeability and a high fracture density. Conventional methods of reservoir engineering analysis are not applicable to coalbeds

May 1, 1969

To pinpoint dust sources and to improve dust control on longwalls. Approach Use short-term gravimetric sampling to determine the severity of various dust sources, and to evaluate dust control techniques used in longwall mining. Short-term gravimetric sampling can be used to isolate dust levels produced by various dust sources. How It Works Traditionally, gravimetric samples have been collected over an 8-hour shift, yielding time-weighted, average dust concentrations. This method gives a good indication of the full-shift respirable dust exposure of underground workers, but is less than satisfactory for identifying dust sources, determining their severity, or for evaluating the effectiveness of dust control techniques. Short-term gravimetric sampling uses equipment available to all mine operators. Two individuals composing the survey team each collect multiple (three to four) gravimetric samples during selected segments of the mining cycle. Multiple samples are necessary to insure accuracy, and to obtain a valid average measurement of the respirable dust concentration when sampling for short periods of time (typically 20 to 30 minutes). The gravimetric instruments may be carried in a sampling package or in a "sampling vest." A fishing vest with four large pockets can be used for this purpose. The sampling pumps are carried in pockets and the sampling head assemblies arc hung across the front of the vest.

Jan 1, 1982

To investigate mine ventilation problems which do not lend themselves to conventional anemometer and smoke study techniques by use of SF6 (sulfur hexafluoride) tracer gas. Approach SF6 tracer gas is released in-to the air at a given mine location. By collecting air samples at various other locations and analyzing these samples for SF6, the amount of air traveling from the release location to each sampling location can be quantitatively determined. Travel time between these locations can also be deter-mined. How It Works SF6 is ideal as a mine tracer gas. It is safe, odorless, chemically and thermally stable, and it generally has no background concentration. Furthermore, it is instrument detectable at concentrations as low as 10 parts per trillion. The SF6 is generally released from a pressurized lecture bottle, and air samples are taken in syringes or evacuated bottles. During the past several years, SF6 tracer gas has been employed to study a wide variety of mine ventilation problems such as: recirculation of return air into In-take airways, air leakage from adjacent mines and gob areas, air transit times through stoped areas, airflow patterns during a mine fire, leakage of gases from an underground oil shale retort into mine workings, face area ventilation patterns, methane flows in metal/nonmetal mines following a methane out-burst, and many other problem areas. Examples of some recent uses of SF6 follow.

Jan 1, 1982

A general analytical solution of the effect of an inclined contact separating two media of differing electrical properties on a normally incident plane electromagnetic field has been given (Geyer, 1972). These solutions for the electromagnetic response at any observation point P(r, [u]) are given in the form of inverse Lebedev-Kontorovich transforms. Two modes of excitation are considered: (1) case where current density flows across strike of the contact separating the media of differing electrical properties (only Er , E [u] , and Hx differ from zero) and (2) case where current density flows along-strike (only Hr , H [u] , and Ex differ from zero). The electromagnetic fields in the frequency range of interest and for the rock conductivities under consideration are quasi-static in nature so that to a first-order approximation the horizontal magnetic field at the surface of the earth is constant and continuous across the discrete discontinuity in resistivity for case (1) above, and so that the tangential derivative of the horizontal electric field at the surface of the earth is constant and continuous across the discrete discontinuity for case (2) above. Of course, it is well known that where large horizontal gradients in conductivity exist, there also exists large anomalous components of the vertical magnetic field (Weaver, 1963). The recognition of such anomalous components and their magnitudes due to the presence of lateral resistivity changes in the overburden becomes very important in any wavetilt type measurement which may be used to locate a miner. When the lateral change in resistivity becomes quite large, the integral solutions (expressed as Lebedev-Kontorovich transforms) simplify considerably and allow ready numerical evaluation. Examples of the amplitude and phase responses of the radial electric, horizontal electric, and vertical magnetic field in the vicinity of the contrast in resistivity are shown in Figures 2, 3, and 4. Of particular significance is the fact that the anomalous vertical magnetic field is three orders of magnitude larger near the contact than far from the contact. This fact implies that where large resistivity contrasts do occur in the rocks overlying mine workings, that significant errors may be present in wavetilt measurements as used above for location criteria! Another observation insofar as the anomalous vertical magnetic field is concerned is the linear variation of phase as one proceeds away from strike in induction number (increased distance or frequency). For a pulse-excited communications system this phenomena would have a bearing on where the zero crossings would occur (i.e., &apos;pulse breadth&apos;) in the transient coupling between any given source-receiver configuration and at any given receiver site.

Jan 1, 1973

Coaxial cable structures form the subject of substantial theoretical and experimental investigations either directly related, or which can be extrapolated, to the communications needs and environments of U.S. coal mines. Communication systems based on "guided" waves, of which "leaky" coaxial cables are one implementation, are attractive candidates for providing a range of communication functions primarily along haulage ways, and possible also within sections up to the working face. (However, there are still strong reservations as to whether a practical coaxial cable sys tem could provide sufficient communications coverage within a section. ) In this Part, we present the results of some theoretical calculations of the performance of leaky coaxial cable communication systems. We also analyze the applicability of the theoretical and experimental results obtained by other researchers to the needs of U.S. coal mines. In particular, this investigation has been focused on the utility of relatively low cost, conventional, flexible, coaxial cable at frequencies covering the LF through HF bands and extending into the lower part of the VHF band, as opposed to relatively high cost, special semi-rigid, coaxial cable* at frequencies in the VHF and UHF bands. There are three major design alternatives for coaxial cable communication systems considered in this chapter: • Base station feeding a coaxial cable with high surface transfer impedance (holes in outer conductor, e.g., braid construction). • Base station feeding a coaxial cable with repeaters (U.K. experiments). • No base station, direct communication via a coaxial cable with periodic radiative structures.

Jan 1, 1974

By H. E. Perlee

Mathematical expressions are derived for the histories of the pressure, flame radius, mass fraction burned, and burned and unburned gas temperatures associated with a spherical flame propagating concentrically in a spherical vessel. The equations are solved numerically for a 9.5 pct CH4/air mixture using the best available information for the burning velocity, expansion ratio, and specific heat ratio. Calculated histories are in complete accord with experimental measurements. The accuracy of calculated histories is determined relative to errors in the system parameters, and it is found that 10 pct errors in either the burning velocity or the expansion ratio results in a 40-pct error in the pressure history. A 10-pct error in either burned or unburned specific heat ratio results in a 22-pct error &apos;in the pressure history. It was further established that the usual assumption of constant specific heat ratio is unacceptable, but equating the burned and unburned specific heat ratios result in no apparent error in the histories. The cubic law (P = Kt3 + Po) is derived and discussed, and it is found that the law is valid only during the early period (P<2 atm) of flame growth.

Jan 1, 1974

By Frank E. Cash

"INTRODUCTION The producing iron-ore ranges in the Lake Superior district are the Marquette and Menominee in Michigan, the Gogebic in Michigan and Wisconsin, and the Cuyuna, Mesabi, and Vermilion in Minnesota. These ranges produce about 85 percent of the iron ore mined in the United States. The accident experience in connection with this production is better than that of the regions producing the remaining 15 percent. Production and shipments vary slightly from year to year owing to stockpiling underground ore during the winter, or nonshipping, season but closely approximate each other over a period of years. This information circular supplements, combines, and continues the data contained in Information Circulars 7321 3/ and 7410 4/, including statistics for 1946 and 1947.Whereas the title ""Accident Experience"" is used for uniformity and logical indexing throughout this report, ""injury"" will be used as a general term to apply to disabilities of all degrees.During the 8-year period 1940 to 1947, inclusive, 619,054,023 long tons of iron ore was shipped from the Lake Superior district. 5/ Michigan and Wisconsin shipped 117,828,939 tons, or 19.03 percent of the total, and employed approximately 9,260 men. Minnesota shipped 501,225,084 tons, or 80.97 percent of the total, and employed an approximate annual average of 12,260 men. The tons produced and shipped per man employed in Minnesota is much greater than in Michigan and Wisconsin, owing to the large open-cut production in Minnesota."

Jun 1, 1949

By James H. Russell

The Bureau of Mines, U.S. Department of the Interior, in cooperation with the Department of Energy, has attempted to increase the activity of nickel catalysts for converting synthesis gas, derived from coal, to a substitute natural gas. This report describes the effects of low-level additions of B, Ca, Ce, Co, Mn, Mo, Pd, Re, Ti, Y, Zn, and Zr on the methanation activity of Raney nickel. The methanation rate at 320° C and the resistance to poisoning by 2 ppm H2S were used to compare catalysts. The effects of the additions were small, and the experimental variances were large, necessitating the use of statistical methods to identify significant effects. Co, Ti, Y, and Zn improved the resistance to H2S poisoning, but only Co improved the methanation rate In some individual catalysts containing Ca, Mo, or Mn, both the methanation rate and resistance to H2S poisoning were improved.

Jan 1, 1980