Search Documents

By Samuel M. Bryant

The purpose of this study was to develop procedures to measure Bingham flow properties for mine tailings and to use these to predict the possible consequences of a hypothetical tailings flow failure at the Tenmile Tailings Pond at Climax, Colorado. The consequences of such a failure were found to be minimal, and the failure itself highly; unlikely. Values of Ty (Bingham yield shear strength) and np (plastic viscosity) were measured for 10 materials using results obtained from vaned coaxial viscometer tests and triaxial tests.

Jan 1, 1983

By Roger M. Turpening

This study was performed to examine the feasibility of using seismic shear waves to detect the presence of abandoned coal mines. !he Antiquity Coal Mine near Antiquity, Ohio was used as a region of known voids. No attempt was made here to accurately locate the mine tunnels if detection was obtained. The results of this study were positive. Sharp changes in the amplitude of the received shear waves were clear indications of the presence of a fluid (gas or liquid) filled region between the source and receivers. When moving the source showed no change in the received signals it was concluded that the voids existed beneath the sensors. Prior to these tests drilling (SM-3) had determined that a void did exist in this area. This void was confirmed by this shear wave test and two additional voids were found.

Jan 1, 2012

By Ren G. Dong, Kristine M. Krajnak, Dan Welcome

Continual occupational exposure to vibrating hand tools can damage the neural, vascular and other soft tissues of the fingers. Rat tail models have been developed to investigate the biological responses of the tissues to vibration.1-2 However, the biodynamic response of the tail relative to that of the human fingers has not been characterized. The objective of this pilot study was to compare the transmissibilities of rat tails measured via a scanning laser vibrometer to those of human fingers gripping a handle. Methods In Part I of this experiment, four male Sprague Dawley rats (6 weeks old) were exposed to discrete 5g-rms sinusoids of 32, 63, 125, 160, 250, and 500 Hz. The rats were restrained in Broome-style restrainers with their tails constrained without compression to an exposure platform via elastic straps as shown in Figure 1. The platform was attached to a vertically vibrating shaker. The vibration was measured for the array of points shown in Figure 1 using a scanning laser vibrometer (Polytec) and the transmissibility calculated for each point on the tail relative to the reference points on the platform. In Part II, three male human subjects were exposed at the frequencies specified in Part I - with the addition of 1000 Hz - at a magnitude at the ANSI <0.5-hr limit up to 63 Hz, after which the acceleration was held constant at 5g-rms. The subjects gripped an instrumented handle at 20 N as shown in Figure 2. The transmissibility was calculated relative to the reference points on the handle. [ ]

Jan 6, 2006

By Charles H. Simmons

Two versions of a VF transceiver to aid in location of trapped miners has been developed and tested. The belt worn model was produced in both transmitter and transceiver configurations. In addition, a quantity of the belt worn models were fabricated using aluminum wire instead of copper in order to reduce unit weight. Ten prototypes of a battery cap model VF transceiver were also fabricated demonstrating further unit size and weight reduction while maintaining electrical performance. Samples of- both versions were tested environmentally and the test data is included in this report. While both versions of the VF transceiver are similar electrically, and are constructed using convential manufacturing techniques, the battery cap model realizes a lower total weight, smaller volume and production cost than the belt worn version. Operationally, the battery cap model assures that the VF transceiver will always be with the miner.

Jan 1, 1981

By William A. Beck

"In 1912 bauxite was discovered in the Andersonville district, which lies in the 28th and 29th land districts of Georgia and comprises parts of Sumter, Macon, and Schley Counties. Mining was begun in May 1914 by the Republic Mining & Manufacturing Co. Considerable ore has been produced in this region since that time by individual interests and by the American Cyanamid & Chemical Corp., which acquired the property formerly owned by the Republic Co.The area was examined in the fall of 1941 by representatives of the Bureau of Mines and the Geological Survey, after which a prospecting program was begun by the Bureau. Drilling was started on December 26, 1941, and continued until November 18, 1943. A total of 1,192 holes was drilled in the district, and 3,679 samples were taken and analyzed.Mineral exploration agreements were signed by 146 property owners covering 42,128 acres. Holes were drilled on 121 of these properties, which have a total area of 38,778 acres.Drilling under this project disclosed several new deposits, of which four have been completely delimited. Previous prospecting in this area by mining companies did not find bauxite, as it lies under heavy overburden. Work by the Bureau indicates 14,412,000 long tons of ore containing 30 percent or more alumina. The total tonnage is divided as follows:Georgia State Highway Routes 26 and 4-9 traverse the district. The Central of Georgia Railroad passes through the center of the entire district (see fig. 1).The project was initiated by J. R. Thoenen, supervising engineer, Non-metals Mining Section, Mining Division, Bureau of Mines. It was under his general supervision until July 1942, after which it was under the general supervision of E. J. Lintner and Rowe McCrae, district engineers for Georgia, South Carolina, and Flordia, respectively.John C. Feeley, Jr., was project engineer from December 1941 to April 1942. Other engineers who assisted in the work on the project are R. E. Babcock, T. M. Romslo, Don M. Coulter, and Walter T. Lewiecki.Acknowledgment is due the metallurgical staffs at College Park, Md., and Tuscaloosa, Ala., for analyses of samples and beneficiation tests.Acknowledgment is also expressed to Alfred D. Zapp, M. W. Harris, Elmer Kneedler,and Parke D. Snavely, of the United States Geological Survey, for their aid, data, and maps.Bauxite was discovered in the Andersonville district in 1912 on lot 187 of the 28th land district, in Sumter County. This lot is situated about 1.5 miles west of the Flint River, on the south slope of the valley of Sweetwater Creek. Mining was started in May 1914 by the Republic Mining & Manufacturing Co. This and adjacent properties were acquired in 1930 by the American Cyanamid & Chemical Corp., which has been operating there since."

Dec 1, 1949

Workers in underground stone mines have a high fatality rate caused by falls of ground from the mine roof or rib. NIOSH recommendations to reduce ground fall injuries and deaths address baskets, mechanical scalers, mechanical bolters, drill steel changing, personal protective equipment, and training. Description of Exposure An informal National Institute for Occupational Safety and Health (NIOSH) review in 1998 identified approximately 17 new underground limestone operations in vari¬ous stages of planning; as many as 35 new underground stone mines are expected by 2005. Many of these new underground stone mines will employ new or inexperienced workers with minimal knowledge of the hazardous conditions that exist underground. Workers in underground stone mines have a fatality rate nearly 20 times that of workers in the manufacturing sector. Three quarters of the fatalities in underground stone mines are caused by falls of ground from the mine roof or rib (Figure 1) [Statistical Abstract of the United States 1985-1999; MSHA 1983-1999]. During 1983-1999, nonfatal ground falls resulted in 140 injuries, or 15% of all underground, lost time stone mine injuries. These nonfatal ground fall injuries resulted in more than 13,800 lost workdays (one third of all lost workdays). Ground falls generate more disabling injuries and time away from work than any other type of incident. [ ]

Jan 11, 2003

The importance of controlling respirable dust and methane gas levels in underground coal mining cannot be underestimated. While respirable dust can significantly affect the occupational health of underground coal miners, methane gas accumulations pose significant safety concerns for these same workers. Water sprays and machine mounted dust scrubbers offer effective control of respirable dust exposures and methane gas accumulations. Water must not only be applied carefully to avoid dust rollback to the machine operator but must create sufficient turbulence to remove dead zones that could contain high concentrations of methane gas. While the flooded-bed dust scrubber has been generally responsible for decreased worker exposures to respirable dusts, this device has proved effective in controlling methane levels at the face. This paper reviews practical applications of water sprays and dust scrubbers to control respirable dust and methane gas on continuous miner faces.

By W. W. Adams

"The main purpose in the compilation of accident statistics is to reveal conditions that may result in injury to persons or property so that remedial measures may be applied. For practical reasons it is usually found necessary to restrict inquiry to conditions which actually have caused personal injury, and to omit those which nay, but have not yet, resulted in damage, Fortunately or unfortunately, there is a sufficient number of the former to indicate the existence of hazards so numerous as to require all of the attention which the industry can devote to the subject.Two years ago, the Bureau of 'mines, in cooperation with the National Safety Council, undertook an intensive campaign to obtain more complete and satisfactory information regarding mine accidents than had theretofore been available. Since 1911 the bureau had been receiving annual summaries from all companies operating metal mines, showing, in a general way, the number and causes of accidents that occurred during the preceding year and the number of men employed at the mines. Monthly summaries of fatal accidents at coal mines were received from the state inspectors, showing the number of deaths attributed to each of 22 main causes of accidents, Information for individual coal mines was not furnished.While this information, nation-wide in scope, is indispensable because it epitomizes the progress or retrogression in the industry as a whole, and serves as a background of specialized studies, yet certain classes of acci¬dents, for example, those that are more or less peculiar to specific districts or mines, require an analysis in greater detail than is possible on the sole basis afforded by the annual summaries.The need for more specific information was realized some years ago in the State of Pennsylvania in connection with the administration of the workmen's compensation law, The mining industry is well acquainted with the val¬uable studies of accidents, particularly nonfatal accidents, in the mines of that State being conducted by Mr. Rush N. Hosier."

Sep 1, 1924

By L. D. Johnson

On a project which is to develop a system to suppress coal dust explosions, a facility has been built and several devices tested. The facility is a 317-foot, 4.5-foot diameter shock tube and to date 53 tests have been carried out with methane-air and methane/coal dust-air as the explosive mixtures. Suppression of slowly propagating (up to 300 ft/sec) flame fronts has been successfully carried out on two tests using the dry chemical extinguishing agent Purple K. Delivery of the material directly into the flame front Seems to be required if effective suppression is to be accomplished.

Jan 1, 1972

By Peter G. Kovalchik, Lawrence W. Scott, Thomas H. Dubaniewicz, Mark A. Fuller

Mine trailing cables operated above safe thermal limits can cause premature insulation failure, increasing electrocution and fire hazards. Previous U.S. Bureau of Mines Pittsburgh Research Center research showed that, under static test conditions, electrical current levels permitted under present regulations may not limit cable temperatures to less than the 90 °C rating of reeled trailing cable. Continuing research under the National Institute for Occupational Safety and Health (NIOSH) addresses thermal characteristics of reeled trailing cable under dynamic test conditions more representative of field conditions, where operators constantly reel in and pay out cable. This research is in support of efforts by industry associations and the Mine Safety and Health Administration to establish safety guidelines for cyclically rated reeled machines. This paper describes a unique approach to measuring temperatures within reeled cable under dynamic test conditions. Fiber-optic sensors embedded within the metallic conductors measure temperatures at 1-m intervals along the entire length of cable. Temperature measurements are reported to be accurate to within 1±° C. The test setup requires access to only one end of the trailing cable, allowing researchers to freely reel in and pay out cable while temperature measurements are made, simulating field conditions. Manufacture of a fiberoptic-embedded trailing cable is described, along with initial test results that indicate the fiber-optic approach is viable.

By Terry J. Close

A mineral resource survey of the 236-mil (611-km2) Hyalite-Porcupine-Buffalo Horn wilderness study area (RARE 11 Areas No. 1-155 G, Gallatin Divide; and H, Hyalite) between the Gallatin and Yellowstone rivers in Montana, indicates there are phosphate rock and petrified wood resources (fig. 1). The area also has some potential for oil, gas, and geothermal resources. Stone and alluvium are abundant but appear to have little potential for development because other sources are available nearer to markets.

Jan 1, 1981

By L. R. Herrmann

The most fundamental feature of fracture is that it involves separation. Such separation can arise by either separation of molecules, more or less along the line joining their centers (tension), or by d sliding separation roughly perpendicular to that line (shear). Theoretically, a perfect crystal could never be broken by the application of perfectly axial compressive stress (until some sub-molecular actions occur). In tension fields the calculated forces between molecules are extremely high. Consequently, calculations based on the forces known to exist in materials at the molecular and crystalline levels always lead to strengths which are two or three magnitudes higher than the strengths obtained in service or in the laboratory. It has been a major problem, therefore, to explain: (a) How fracture can occur in compressive stress states. (b) Why the observed strength of a material is always much lower than its calculated strength.

Jan 1, 2012

A computer system for calculating the illumination on coal mine surfaces due to machine-mounted lights is described. Utilizing numerical models of mining machinery and measured data on luminaire output characteristics, the program computes the ft-candle levels incident on the mine entry surfaces for any desired machine/luminaire/ entry configuration. Shadowing effects of the machine are taken into account. Results are provided at 2 ft. intervals on the face, left and right walls, floor and roof. The system operates, interactively from a Tektronix 4014 graphics terminal which handles all input/output functions. The software is installed on a Cyber 74 computer that communicates with the terminal via telephone line.

Jan 1, 1978

By John E. Urosek, Dennis A. Beiter, William J. Francart

In This Chapter [Designing bleeder systems Examining and maintaining bleeder systems Evaluating bleeder system effectiveness] INTRODUCTION Bleeder systems are that part of the mine ventilation network used to ventilate pillared areas in underground coal mines. Pillared areas are those in which pillars have been wholly or partially removed, including the areas where coal has been extracted by longwall mining. Bleeder systems protect miners from the hazards associated with methane and other gases, dusts and fumes, and oxygen deficiency that may occur in these mined-out areas. Effective bleeder systems control the air passing through the area and continuously dilute and move any methane-air mixtures and other gases, dusts, and fumes from the worked-out area away from active workings and into a return air course or to the surface of the mine. A bleeder system includes the pillared area (including the internal airflow paths), bleeder entries, bleeder connections, and all associated ventilation control devices that control the air passing through the pillared area. Bleeder entries are special air courses designed and maintained as part of the mine ventilation system. [This chapter focuses on the design, examination, maintenance, and evaluation of bleeder systems in underground coal mines.] The history of coal mine explosions in the United States is a reminder of the importance of adequate ventilation. Some of those disasters were the result of inadequately ventilated pillared areas. The importance of developing bleeder systems to ventilate these pillared areas and evaluating the bleeder system’s effectiveness is reflected in present-day federal regulations. For more information on bleeder systems, see Tisdale [1996] and Urosek and Francart [2002].

Jan 6, 2006

By Richard L. Sanford

This report summarizes the results of the development of a Directory of Computer Programs Applicable to U.S. Mining Practices and Problems. The Directory includes a sampling of computer usage in operating and manufacturing companies, consulting firms, computer companies, research organizations, universities, and various U.S. government agencies. References to computer applications throughout the mining industry are presented as well as comments on the availability of programs to interested organizations or individuals.

Jan 1, 1977

By Stephen E. Stewart

This document presents the explosion-proof enclosures used severity of certification tests solutions to linear transient thermal and stress analyses of in underground mines. The results were used to assess the for enclosure windows relative to possible loads occurring in the actual mine environment. Cast iron electric light enclosures with polycarbonate and glass windows were analyzed under steady state thermal conditions (light burning) and for thermal shocks corresponding to an internal explosion (ignition of volatile mine gas) or external quenching (mine water spray system). Thermal shocks to the enclosure, caused by ignited gases or water spray, were applied via a series of load steps in the transient analysis. The temperature dependence of material I properties and of the film heat transfer coefficients were included in the model. The work demonstrates that thermally induced stresses are strongly influenced by the way the window is mounted in the enclosure. It also shows that the MSHA Thermal Shock Test, if performed on an unsupported lens (or window), produces lower stresses than the lens (or window) may experience in the mine environment.

Jan 1, 1984

By George W. Huseman, W. D. Mcmillan

"INTRODUCTION Feldspars represent one of the most abundant groups of minerals and constitute nearly Go percent of the material contained in the igneous rocks. They are grouped in a series of related aluminum silicates with varying amounts of potash, soda, and lime. .Approximately 85 percent of the feldspar produced in the United States is used as a flux in the production of glass, pottery, enamel and sanitary ware, brick, and tile. Notwithstanding the abundance of feldspar in the earth's crust, the only deposits that are worked to any extent are the pegmatites or coarsely crystalline dikes where natural segregation of the constituents facilitates recovery of the feldspar with a minimum of free quartz, mica, tourmaline, garnet, and other iron-bearing minerals that are detrimental in most ceramic industries.Although there are three glassplants and numerous other ceramic industries in Texas, all of the feldspar used in these plants is from other States. In the Llano region of central Texas, however, there are numerous coarse pegmatite dikes consisting primarily of feldspar and quartz in ratios up to 3 to 1. One of the more important of these dikes is the Badu Hill deposit in Llano County, Tex., which was first described by Carl Chelf 4/ in 1942. Following an examination of the deposit by W. D. McMillan, engineer in charge of the Texas field office of the Bureau of Mines, in January 1946, a proposal was made to investigate the deposit by core drilling in cooperation with the Department of Ceramic Engineering, University of Texas. This report presents the results of the cooperative investigation, which was begun April 24, 1946, and completed May 17, 1946."

Jul 1, 1947

By Terry J. Close

In 1986 and 1987, at the request of the U.S. Bureau of Land Management, U.S. Bureau of Mines personnel studied 7,040 acres of the 7,240-acre Sheep Mountain Wilderness Study Area (OR-006-003) in order to evaluate its identified mineral resources. The area studied is along the divide between the Snake River and Pine Creek about 1.5 mi south of the village of Oxbow in Baker County, OR. No mineral resources or mineral-related activities were identified in the Sheep Mountain study area. The basalt covering most of the study area has no known mineralized sites. However, it contains common agate and opal that is of limited interest to mineral collectors. This basalt (stone) could be used locally as construction material (crushed stone or fill); however, suitable material is wide spread in the region and more accessible to possible markets.

Jan 1, 1987

By Louis H. Berkelhamer

"INTRODUCTION In the present war, with increasing demands on foundrymen for speedy production of sound castings, the role of sand in foundries has paramount importance.Foundry sands include both molding sands and core sands. Molding sands are those used in making molds, whereas core sands include those used for ""cores"" that fill the parts of the mold intended to be openings or hollow spaces in the casting. Core sands are, as a general rule, relatively coarse-grained as compared to molding sands. Coarse-grained sands, however, are required in making molds for large castings.Owing to the intimate relationship between properties of the sand and casting defects, it is necessary (for most efficient foundry work) to keep a close check on the molding sands used and to properly select and prepare a sand for a specific job. A mold is essentially an unfired refractory composed to meet specific requirements as to strength, permeability, and resiliency. Good green strength is important in preparing and handling the mold. Low dry and hot strengths contribute to cutting and washing, whereas high strengths cause difficult shake-out, with subsequent loss of sand. When molten metal is poured into the mold: a dried skin is attained, and gases from moisture and combustibles are driven off. Excessive moisture necessary for the proper working of a sand, as well as poor venting due to low permeability, are factors responsible for producing such defects as blows and pinholing. The skin of the mold, upon contact with molten metal, first expands and later contracts; these conditions are favorable for producing scab defects. Contact with the molten metal sometimes causes the skin of the mold to sinter or fuse and may produce a sand burn on the casting. Then again, the mold may develop excessive hot strength rapidly, thereby causing a cracked casting. Experienced foundrymen can other such relationships, too numerous to be included here."

Sep 1, 1944

By Paul J. Remington

The field data gathered as part of the measurements described in Volumes I and II were re-analyzed in the low frequency regime (.1 Hz to 1 Hz) where motion sickness normally occurs. These data were compared co the international standard ?ISO 2631 Addendum 2: Evaluation of exposure to whole body z-axis vertical vibration in the frequency range 0.1 to 1.0 Hz." For both underground mining machines and surface mining machines the results showed that one would not expect motion sickness to .be a severe problem. New field data were gathered on the vibration reduction performance of various seat designs found on surface coal mining machines. The vibration during normal operation was measured on the seat using the standard seat pad accelerometer package described in the previous two volumes and simultaneously on the floor of the machine at the base of the seat. Preliminary indications are that the so-called high performance seats used for operator vibration reduction do not offer significant improvement over conventional seats.

Jan 1, 1984