Search Documents

By Mark Sanders

This report describes an experiment which was conducted to compare the relative bumping hazard of a low and high profile hard hat (helmet) in a low seam mining environment. The study was specifically designed to assess the effect of lowering the helmet profile on frequency of head impacts in an underground low seam coal mine simulator. This involved subjects performing four common low coal mining tasks wearing the low and high profile helmets in the low seam simulator (36" and 48? heights). The results of the study indicated that a low profile helmet could reduce bumping frequency in underground low coal approximately 25%, and as much as 80% on selected tasks. It was beyond the scope of the study to measure the impact force, thus it was not possible to estimate the effect of the low profile helmet on severity of impacts underground. The research team recommended that a more extensive investigation be made of head injuries experienced in low seam mining (both underground and surface) with the objective being to assess the impact of a low profile helmet on total head accident exposure.

Jan 1, 1980

By Lyda W. Hersloff

An environmental monitoring program was established to assess the baseline of parameters which may be impacted by a research and development hydraulic borehole mining operation. During the baseline program, two aquifers were identified at the borehole site with the overlying sand aquifer being distinct from the ore sand aquifer on the basis of radiological parameters. The direction of flow of groundwater was determined to be north 19° west at a rate of 1.82 feet per year. Tests to determine the effect of backfilling the boreholes indicated that using overburden from the open pit mining operation would not significantly increase the radiological consti¬tuents of the ore sand aquifer. Mining measurements of the- radon flux from the borehole indicated that the actual release rate of 0.035 pCi/sec was several orders of magnitude less than the calculated estimate by the Environmental Protection Agency. Finally, a gamma survey conducted at the site indicated that the terrestrial component of background radiation was consistent with that in areas near uranium deposits. The methodology used as well as the supporting data are given in this report.

Jan 1, 1981

The Appalachian Mountains divide Pennsylvania into two distinct coal regions, bituminous and anthracite. The western region of the the state, where the majority of bituminous mines are located, is characterized by mountains and gently rolling hills. Bituminous coal seams underlie about 12,000 square miles in 28 counties. The anthracite coal region, located in the northeast, covers approximately 3,300 square miles. This area contains more than 20 different coal beds that vary in thickness from a few inches to 50 or 60 feet. The anthracite region is characterized by steeply pitching seams that require highly specialized mining techniques and present unique challenges for solving problems such as the mine subsidence associated with abandoned underground anthracite mines. For more than a century, coal has played a major role in the economic and industrial development of Pennsylvania, particularly the steel industry. Estimated bituminous reserves total 23 billion tons, or 5.3 percent of U.S. reserves, and anthracite reserves total 7.1 billion tons, or 97 percent of U.S. anthracite reserves. Pennsylvania received conditional approval of its regulatory program July 31, 1982. Pennsylvania's Abandoned Mine Land Program was approved on the same date.

Jan 1, 1992

By Richard S. Gaps

The Derby and Alexander Claim, located within the Tunnel Ridge Wilderness Study Area (WSA), has placer gold resources. No lode deposits are known within the area, but lode gold deposits are found within 1 1/2 mi of the WSA. In additon, rock units which contain lode gold deposits north of the WSA are found within the northern portion of the study area. INTRODUCTION The Tunnel Ridge Wilderness Study Area (WSA), CA-030-402, encompasses 4,623 acres of BLM administered public land in Trinity County, California, about 35 mi west-northwest of Redding (fig. 1). Major access to the Tunnel Ridge vicinity is by U.S. Highway 299. Ac-cess to the WSA boundary is by a secondary paved road from Junction City and several light duty dirt and gravel roads (fig. 2). The WSA is on the southwest slope of Weaver Bally Mountain. The topography is rugged with moderate to steep slopes; elevations range from about 1,600 ft to 5,900 ft.

Jan 1, 1983

By Russell J. Miller

A high-pressure intensifier system was designed, constructed and field tested as part of a program to determining the feasibility of applying high-pressure water jets on conventional mechanical rock excavation equipment to increase advance rates. Also developed were a high-volume swivel, capable of transferring the high-pressure water to a rotating cutterhead and manifold system for locating and protecting the jets on the cutterhead. Field tests were conducted in a granite quarry near Skykomish, WA, approximately 90 miles east of Seattle. The concept of improving excavation rates by using water jets to assist mechanical cutting was proven to be successful, with an average increase in excavation mete of 50 to 60%. For some tests, the excavation rate was more than doubled. Machine torque requirements were reduced approximately 25% when the water jets were used. It was suggested this was due to reduced cutterhead friction in the presence of the water jets. A comprehensive economic analysis was undertaken as part of a concurrent study to determine the degree of cost benefits attainable from increased advance rates. Very significant savings were seen to be possible. It was concluded that the basic concept of combining a water jet capability with a mechanical excavating machine is definitely possible.

Jan 1, 1976

By Gary E. Sherman

Preliminary economic mining feasibility studies were conducted by the Bureau of Mines to estimate mining costs in the Juneau gold belt area of the Juneau Mining District, southeastern Alaska. Investigations were conducted on the economics of two mineral deposit types: (1.) Berners Bay vein gold deposits, and (2.) stockwork gold deposits containing gold, silver, and lead. Cost estimates were developed using the Bureau of Mines Cost Estimating System (CES). Discounted cash flow return on investment (DeFROI) was calculated using the Bureau's MINSIM computer program. Underground mining of a Berners Bay vein gold deposit was found to be economic (15 pct DCFROI) at a recoverable metal value of $353.67/mt for a 100 mtpd shrinkage stoping mine with a 10 yr mine life, $324.76/mt for a 20 yr mine life, $138.63/mt for a 500 mtpd longhole stoping mine with a 10 yr mine 1 ffe, and $127.50/mt for a 20 yr mine life. Block caving mining of a large stockwork gold deposit was found to be economic at a recoverable metal value of $15.28/mt for a 18,000 mtpd mine with a 20 yr mine life.

Jan 1, 2011

By R. T. C. Rasmussen

"INTRODUCTION The primary purpose of the Bureau of Mines electrolytic manganese pilot plant at Boulder City, Nev., is to improve the Bureau-invented electrowinning process and to determine the applicability of the process to the extensive domestic low-grade manganese ores with a view to making the United States dependent upon foreign sources of manganese. 3/4/ Incidental to accomplishing this purpose, the pilot plant has produced a substantive quantity of electrorytic manganese since the start of operations late in 1941; present cabacity about 1 ton a day of manganese metal. A second important purpose of the pilot plant is the supplying of electrolytic manganese for full-scale tests in cooperation with industrial users of manganese.The Rustless Iron& Steel Corp., Baltimore, Md., was the first steel company to cooperate with the Bureau of Mines in large-scale testing of electrolytic manganese. Arrangements were made with C. E. Tuttle, then president of the corporation, whereby the Bureau would supply electrolytic manganese to make a sufficient number of full-scale stainless-steel heats to demonstrate thoroughly its merits as a replacement for low-carbon ferro-manganese in the corporation's stainless-steel practice. The corporation's purpose in the investigation was to determine the possible advantages of electrolytic manganese resulting from its almost complete lack of phosphorus and caroon that might offset its then considerably higher cost per unit of manganese than low-carbon ferromanganese. The data presented herein are based upon reports of A. L. Field, technical director, and L. Weitzenkern, research engineer of Rustless Iron & Steel Corp.; they are supplemented by observation of the author who visited the plant during the tests."

Oct 1, 1945

By Elmer E. Buban

A lightweight compressed oxygen rescue breathing apparatus (RBA) for rescue and recovery missions has been developed by Mine Safety Appliances Company under contract to the Bureau of Mines. The apparatus is a positive pressure, closed circuit system of 4 hours duration. The weight of the complete apparatus, including an optional cooler, is slightly over 30 pounds. Weight reduction over currently available RBAs is achieved through the use of lithium hydroxide for scrubbing C02 in place of conventional chemicals and the use of a composite glass fiber/ aluminum shell cylinder for oxygen storage in place of steel cylinders. Positive pressure is maintained in the breathing circuit at all times by applying a constant spring force to the breathing bag. The harness has been designed to reduce the work of the wearer by redistributing the weight of the apparatus to the wearer's hips.

Jan 1, 1981

By Robert A. Cortese, Henry E. Perlee

Coal dust and float coal dust, produced during normal mining operations, in underground coal mines, are carried from the point of origin downstream by the ventilating air, where it deposits on the surfaces of the mine entry. In an explosion, this dust is lifted from the surfaces by the aerodynamic disturbances and, if of sufficient quantity, can continue to propagate the explosion. To prevent the surface coal dust from contributing, it must be inerted, typically by spreading pulverized limestone, i.e., rock dust, over the coal dust surface. To facilitate the dusting operation, the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory(PRL), developed an automated system that continuously monitors the accumulation of coal dust. This system could activate a rock-dusting machine that disperses rock dust into the ventilation air when dangerous deposits accumulate and deactivate the machine when sufficient inert has been deposited on top of the coal dust. The system consists of a microprocessor-controlled optical float dust deposition meter. This device measures the light intensity reflected from a deposited layer of dust. A standard cap lamp is used as a fixed-position light source. From the reflected light signal, the microprocessor determines the hazard level of the deposited layer and performs the appropriate action. Full-scale studies conducted in the Experimental Mine at PRL's Lake Lynn Laboratory, using alternating thin layers of rock dust and coal dust, successfully demonstrated the operation of the device. Based on the statistical data from these studies, a mathematical model was developed to predict long-term error in total rock dust content using this inerting procedure. Downwind dust dispersion was also examined to provide optimum placement of the dust sensors and to determine the need for better rock dust dispersion techniques.

Jan 5, 1998

By J. R. Cobble

As part of the Federal Bureau of Mines project to develop new or improved materials for metallurgical furnace applications, the Tuscaloosa (Ala.) Research Center has conducted research to develop a reproducible laboratory test for evaluating the resistance of refractories to molten slags. Tests were conducted with a slag representative of slag used to produce mineral wool. A rotating cylindrical furnace was lined with the brick being tested, and it was operated at temperatures up to 1,660° C for periods ranging from 8 to 32 hours. The effects of such variables as slag temperature, rotational velocity, charge rate, and contact time on refractory erosion were determined. The research demonstrated the reproducibility of the test procedure developed.

Jan 1, 1980

By William Porter

Hand scaling is a physically demanding job and is responsible for numerous overexertion injuries in mining. This experiment studied rib scaling from an elevated bucket to examine force generation capabilities and electromyographic responses to a prying subtask. Subjects exerted force using two bars (steel and fiberglass) at five target heights. Work height significantly affected peak prying force during scaling activities with highest force capacity at the lowest level (p = 0.0188). Bar type did not affect force generation (p = 0.7843): However, use of the fiberglass bar required significantly more muscle activity to achieve the same force (p < 0.05). It was concluded that miners should scale points on the rock face that are below their knees, and reposition the bucket as often as necessary to do so. Additional research is needed to fully understand the impact of bar type on the physical demands of an entire scaling task.

Jan 1, 2006

By Bruce I. Thomas

Reconnaissance studies of beach sands along the eastern part of the Gulf of Alaska were conducted by the Bureau of Mines to determine if any of these coastal areas warranted investigations as possible sources of valuable minerals. Because of difficult access and limited transportation facilities only a minimum of sampling, surveying, and camping equipment is utilized to obtain spot samples from key areas as well as information indicating the location, size, and character of the deposits. Such data were obtained from beaches located along approximately 247 miles of the Gulf of Alaska coastline during parts of the 1957 and 1958 field seasons. A total of 201 3-inch-diameter auger holes, spaced roughly at 1 mile intervals, were bored by hand methods to depths ranging from 3 feet to 27 feet; also 33 shovel samples were collected from selected localities. Samples were reduced to a rough concentrate in the field by panning; the rough concentrates were shipped to the Bureau of Mines laboratory at Juneau for further concentration and for petrographic and chemical analyses. Particular attention was given to the heavy-mineral content of the concentrates, although the types and relative amounts of rock-forming minerals were also determined. The reconnaissance indicated that, generally, the valuable mineral content of the beach deposits was too low to be of further interest except in the vicinity of Yakutat and Lituya Bays where erratic but possibly significant concentrations of magnetite and/or ilmenite were found. At Yakutat, about 20 miles of beachline extending southeasterly from Ocean Cape, yielded samplas containing from 1 pound to over 300 pounds of iron and from a trace to over 100 pounds of titanium dioxide (TiO2) per cubic yard of beach material. However, the higher grade samples represented local concentrations of minor importance. The general tenor of the Yakutat beach, as indicated by the airthmetical average of 27 auger-hole samples, is about 35 pounds of iron and 20.5 pounds of titanium dioxide per cubic yard of beach material. Ilmenite is the predominant heavy mineral of the beach deposits in the vicinity of Lituya Bay, but it was found in concentrations only in limited areas near the

Jan 1, 1962

By J. L. Schwendeman

This is the final report of work done under contract H0210060 for the U. S. Department of the Interior, Bureau of Mines. This program was to show the feasibility of using plastic liners containing sand and other fillers as a means of roof support in coal and other mines. This laboratory study was conducted in two phases, namely: Phase I, directed toward determining which state-of-the-art resin systems might have utility as a means of roof support in a coal mine, consisted of a canvass of resin manufacturers to learn which resins were available commercially that might have utility for this application. The resins submitted by the manufacturers were evaluated in a number of simple tests to define which of them would be most suitable for roof support use.

Jan 1, 1972

By G. A. Bole

"This paper presents a review of the literature and is an epitome of work acne and articles published by Schurecht, Robson and Andrews', in the investigation of the feasibility of making basic refractories from dolomite, was carried on successively by these men, at the Ceramic experiment Station of the Bureau of Mines, Columbus, Ohio.Scope of the work.The dolomite refractories investigation of the Ceramic Station includes a study of the many fluxes which could be used to aid in the dead-burning of dolomite and also a complete survey of the iron oxide-alumina-silica field as fluxes. The temperature of calcination and the resulting properties have been carefully investigated, and the most desirable calcines chosen for further investigation in the making of dolamite bricks. Many binders and the several methods in common use of fabricating bricks commercially were tried, and a thorough study was made of the properties of the most successful ware,Previous Investigators.Even before the World War, considerable work was done on dolomite this war greatly accelerated the efforts of the many Investigators."

Jul 1, 1924

By Steven W. Schmauch

The Sugarloaf RARE II area (No. 5296) covers 11,100 acres in the northern part of the White Mountain Range, in the Inyo fictional Forrest. It is in Nevada, about 45 mi north of Bishop, California. A mineral survey was conducted by On U.S. burro of Mines in 1982 and by the U.S. Geological Survey in 1980-1982. The Bureau reviewed pertinent literature, searched Esmeralda and Mineral County mining records, obtained current claim information from the administrative agencies, and contacted claim owners. Thirty-six properties were examined, and 674 samples were taken from them to help assess win oral resources and potential. The Geological Survey evaluated the regional mineral potential by geologic, geochemical, and Geophysical surveys.

Jan 1, 1983

By Thomas E. Finch

This report is a continuation and expansion of a previous USBM grant (No. G0254004) which examined alternative methods of handling the parting between two coal seams in a surface mining operation. The alternative methods consist of equipment implementation in either a stowing or haulback technique. Following a typical strip mine conformation, the parting is directly stowed or hauled back and placed in the pit bottom after second seam removal. The objectives are to produce an environmentally sound material placement technique and to increase prime stripping machine utilization. This report contains the engineering philosophy behind two computer programs created to evaluate parting handling methods over d wide range of coal and parting thickness ratios. The nature of the computer approach allows cost sensitivity analysis and quick updating of costs. The two programs are clearly presented with documentation and examples such that consumers may apply then to their own operations.

Jan 1, 1977

By M. G. Wallis

This report presents the results of a study to develop a detailed mining method design based on longwall mining with sublevel caving. The method is applicable to low-dipping coal seams 20 or more feet thick such as are found in the western United States. The report covers (1) the development and description of the mining method, (2) evaluation of the engineering feasibility of the design, (3) estimates of productivity and recovery, and (4) an engineering cost analysis and economic feasibility evaluation of the mining method design.

Jan 1, 1977

By Terry R. Neumann

During 1983, U.S. Bureau of Mines personnel examined mines, prospects, and mineralized zones to evaluate the mineral resources and potential of the Funeral Mountains Wilderness Study Area (WSA), Inyo County, California. Eleven mineral properties and two mineralized zones were examined during this study. Of these, six are within the study area and seven adjacent. There are no active mines, in the WSA, nor is there evidence of past production from any claim within the study area. The WSA contains no identified mineral resources. However, occurrences of bentonite, zeolites, and strontium were found in the area. There is little likelihood for resource development of any occurrence in the WSA. The area, in the Basin and Range Physiographic Province, is dominated by a Paleozoic marine sequence. Segments of Tertiary continental fluviolacustrine sediments, including volcaniclastic rocks, abut and overlie the Paleozoic rocks in fault controlled basin areas. Significant concentrations of bentonitic clay and zeolites occur as alteration products in Tertiary tuffaceous sedimentary rocks. However, they are generally low-grade, thin, and discontinuous, precluding commercial development. Limestone, quartzite, and sand and gravel in the area are suitable for many types of construction uses, but similar deposits outside the WSA are closer to markets. No energy resources have been identified in the WSA.

Jan 1, 1984

By L. R. Herrmann

The research described in this report is the first phase of a comprehensive program for the development of a characterization for the structural properties of rock masses. The mathematical expression of the characterization is especial&apos; tailored for use in conjunction with modern structural analysis procedures. The objective of the first phase of the project is to determine the feasibility of representing the structural properties of rock masses in terms of the analysis of an appropriate "representative volume" the results of this investigation are described in detail in the body of the report. The current state-of-the-art concerning the understanding and description of the fundamental mechanisms of rock behavior are determined from a survey of existing literature. The development of a representative volume that captures the most important of these mechanisms is described, In order not to unduly obscure the fundamental aspects of this development, the mathematical analysis of the representative volume is limited to plane strain conditions. A subroutine for the numerical evaluation of the proposed model (i.e., the analysis of the representative volume) is presented. The steps necessary for the incorporation of the subroutine directly into existing two-dimensional finite element structural analysis programs are described. Comparisons between the predictions of the proposed characterization and published results of simple laboratory tests are presented and discussed. Finally recommendations are given concerning suggested improvements of the model and the extension of it to the general three-dimensional case.

Jan 1, 1974

By A. L. Foote

This is the final report of work accomplished during 1973-75 under U. S. Bureau of Mines Contract No. H0242015, "System for Handling Underground Mine Supplies and Materials." The purpose of the contract was to develop a mechanical device which could safely perform handling tasks that are normally done manually in underground bituminous coal mines. The report discusses studies leading to construct-ion of a battery-operated, three-wheel vehicle with a six-degree-of-freedom manipulator. Supportive design studies included collection and analysis of production, manual functions, and injury data on the underground bituminous coal mining industry. Transfer tasks in section storage and working places were the prime candidates for mechanical handling. Functional specifications were developed for two handling devices (one to handle existing unit loads and one to handle repackaged unit loads) and for a vehicle to mount the handling device. Design concepts for nine different handling devices were developed and a cost/benefit evaluation made for each. Detail design, capital and operating costs, and method improvement savings data were developed for two battery-operated vehicles and for two different manipulators. The three-wheel vehicle with anthropomorphic manipulator was chosen for development.

Jan 1, 1978