Search Documents

By G. W. Clark

"The mining of the ore bodies at Rabbit Lake has in the past been by the open pit method. This method is presently being used to develop the B-zone and will continue into the future with the development of two smaller ore bodies, the A-zone and D-zone. The Eagle Point orebody will be developed by an underground method which will provide production and employment into the next century.The ore bodies at B-zone, A-zone and D-zone are unique in that they are located under Wollaston Lake. To permit mining by the open pit method a steel-celled dyke has been constructed around the north end of the B-zone. This same dyking method will be used for the A -zone and D-zone. INTRODUCTIONMine development at Rabbit Lake commenced in 1970when a detailed engineering feasibility study established the viability of the Rabbit Lake deposit. In 1972 construction of the mill and camp site began. Construction materials were seasonally hauled to the site over a winter road until November 1973when the government of Saskatchewan completed an all-weather road to within six miles of the operation.In October 1974, stripping of the Rabbit Lake open pit began with the removal of overburden and lake bottom sediments from the previously drained Rabbit Lake. The first ore was processed by the mill in June 1975and by October the mill was producing three million pounds per year. The design capacity of five million pounds annually was first achieved in 1977 and maintained until 1981, when lower ore grades resulted in lower production rates .It was clear when mining at Rabbit Lake began that, without additional reserves, the Rabbit Lake operation had a life of less than 10 years. Exploration, therefore, continued in the immediate area in an attempt to discover additional uranium mineralization."

Jan 1, 1989

By D. D. Liu

This paper proposes a charge induction dust measurement method based on detrended fluctuation analysis (DFA) for use in coal mine environments, based upon electrostatic interference, dust properties, wind speed, particle size, moisture content and other factors. In this methods, sequence x(t) is first obtained through a dust concentration sensing probe, and then the cumulative deviation y(t) is calculated, and y(t) is divided into same lengths. Secondly, a first-order linear fit is used for data of each interval, and mean-square deviation filtered DFA was calculated for each interval. Finally, the dust mass concentration of the corresponding time is obtain by supplemented calibration coefficient and fitted the data point which is the mean and square root for all lengths of interval. Simulation and verification experiments showed that the charge induction dust measurement method based on DFA can reduce coal mine electrostatic interference effects with high accuracy. The design has been successfully applied to select areas.

Aug 1, 2013

By L. Rosato

In the past decade, as a result of increasing iron loads, Canadian Electrolytic Zinc (CEZinc) has become a pioneer in understanding the critical factors that affect the roasting of concentrates with high pyrite contents as well as those factors governing the effects of high iron loads on the leaching circuit. De-bottlenecking efforts in the roaster and acid plant section of CEZinc have given rise to a better appreciation of the impact of iron on roaster productivity. High standards for impure solution quality, zinc recoveries and residue disposal have all led to an increased comprehension of the limits of the leaching circuit and the optimization potentials with respect to iron and ferrites. In this paper, the impact of iron on the roasting and leaching circuits of CEZinc will be reviewed and special emphasis will be given to some of the more recent process optimization and improvement activities.

Jan 1, 2006

By I. H. Warren, F. A. Forward, A. Vizsolyi

"Observations are reported on the pressure leaching of material produced by subjecting chalcopyrite to two types of heat treatment. Calcination of the mineral at 825°C, in the absence of oxygen, induces some sulphur loss by volatization, producing a material from which copper can be leached more rapidly than from chalcopyrite. Treatment of the mineral with elemental sulphur at 475°C leads to sulphur uptake accompanied by a change in mineralogical structure of the chalcopyrite. Copper is prefer-entially and rapidly leached from the sulphur-treated material. A tentative explanation of the sulphur-chalcopyrite re-action is presented."

Jan 1, 1968

By F. M. Clement

British Columbia, unlike the Prairie Provinces, cannot lay claim to vast prairies. She can, however, claim many valleys, uplands and plateaus that are capable of marked agricultural development. It has been said that British Columbia is not an agricultural province. This may or may not be true, but at the present time agricultural production in this province stands second only to that of forestry. The industry has advanced from a total production of 8 millions in 1908 to a total production of 60 millions in 1924, a total increase of approximately 650 per cent in 16 years. In the last 10 years production has increased from 30 millions to 60 millions. No other industry can point to such a rapid development. In 1908 British Columbia imported 12 million dollars worth of foods compared to the 8 millions which were produced at home. In 1924 she imported 20 million dollars worth of foods compared to the 60 millions worth produced at home. In addition we exported foods to the value of approximately 10 million dollars. British Columbia is therefore self-sufficing in-so-far as values ar.e concerned except for approximately 10 millions of dollars. It is not to be expected that this province will ever grow all the coarse grains that she may require: these, along with certain meats, will always be a heavy item in the imports. We are concerned at the present time more with the value of the products than with the quantities produced: in other words, with quantities only in-so-far as ? quantities improve value.

Jan 1, 1925

Phelps Dodge has recently operated a commercial scale, super fine grinding circuit of copper concentrates for use in a medium-temperature pressure leaching process. Two 355 kW vertical stirred mills were installed in series, targeting a grind of 80% passing 7.5 µm and 98% passing 15 µm as outlined in Phelps Dodge's concentrate leaching patent portfolio. This paper details the operation and results of the test program at Bag dad, as well as some of the operating challenges encountered.

Jan 1, 2007

By A. A. Levinson, M. B. Kirkley, J. J. Gurney

"Scientific advances in the past decade have greatly clarified our understanding of certain concepts relating to the age and origin of diamonds. These advances are largely the result of geochemical studies of mineral inclusions in diamonds, made possible by modem analytical techniques which enable the accurate chemical analysis of micro-sized particles of the order of 200 microns in maximum dimension. As a generalization, the inclusions indicate that most diamonds formed from either of two rock types, peridotite and eclogite. Peridotitic diamonds have yielded ages of 3300 million years, whereas eclogitic diamonds areyounger and rangein agefrom approximately 1000to 1600million years. Kimberlite and lamproite, the two rock types usually associated with diamonds, typically are much younger than the diamonds they contain. Thus, it is now dear that kimberlites and lamproites are only the transporting mechanisms which brought diamonds to the surface and are in no way related to the formation of most diamonds. The latest concepts which developed during the past decade regarding the sources of carbon for the crystallization of diamonds from peridotite and eclogite, and the mechanisms of kimberlite and lamproite emplacement, IntroductionThe decade of the 1980s has seen major advances in our understanding of the age, origin and emplacement of diamonds. The information presented herein is applicable to virtually all natural diamonds, excluding diamonds related to meteorite impacts. There is still some question, however, as to the applicability of the new information to industrial grade ""fibrous"" or ""coated"" diamonds, and to microdiamonds (< 1 mm). In addition to drawing upon our own experiences, this review is summarized from a voluminous literature and for those interested in the original sources we recommend the books by Mitchell and Bergman (1991), Ross (1989), Nixon (1987), Mitchell (1986), Glover and Harris (1984) and Dawson (1980), and the review articles by Mitchell (1991), Gurney (1989) and Meyer (1985).are also discussed."

Jan 1, 1992

By Geir M. Haarberg

Electrochemical techniques, mainly linear sweep voltammetry and potential step chronoamperometry, were used to study the behaviour of dissolved phosphorus species in cryolite-alumina melts, The presence of AIPO4 or Na3PO4 gave rise to voltammetric current waves due to electrode reactions involving phosphorus species at potentials where dissolved alumina is stable in cryolite melts, Diffusion kinetics for dissolved P(V) species were studied, Data from industrial cells were used to determine mass balances for phosphorus, For cells being fed with secondary alumina, more phosphorus tends to end up in the produced metal, Laboratory experiments to study the effect of phosphorus in the bath on the current efficiency for aluminium were also carried out.

Jan 1, 2004

By E. A. Davies, Trevor T. Jones

"Aspects of materials, design and operation of suspension equipment is dealt with, hazard, fatigue and special metallurgical properties of certain steels to resist are described, as is the effect of temperature in service modifying the properties of some steels to resist stress concentration and propagation of cracks.The influence of steady impact and fatigue loading and its results are described. Control of manufacture including nondestructive testing is outlined and acceptance parameters and strength calculations are given. Quality requirements and control in manufacture are outlined. A short description of the overwind detaching hook, together with illustrations of the operation of detachment are presented.MaterialsWinding engine ratings of 8000 h .p. and large capacity shafts 2000 m in depth (4000 m depths have already been reached and it may be necessary to go to 6000 m) and up to ten conveyances are not uncommon today. Loads of 100 or even 200 tons hoisted at low speeds are possible within the near future. Some of these appliances are designed to protect lives and installations in hazardous conditions when, due to human or mechanical fault, a malfunction occurs in the system. In addition, such equipment includes suspension gear of various kinds designed to anchor and apply high mechanical tensions to numerous steel ropes installed in shafts necessary either for the safe passage of conveyances or for balancing purposes when heavy loads are in motion.No unique metallurgical problems are presented in underground mining operations, but they have two special characteristics that influence the metallurgical aspects of the de sign of suspension gear and other equipment concerned in the transport of men and materials. (1) Any uncontrolled release of energy caused by the unexpected failure of a component is more likely to injure personnel and cause costly damage to installations in the narrow confines of an underground mine shaft. (2) Some mechanical equipment in mines, tends to be overloaded in service and suffer plastic distortion."

Jan 1, 1987

By Luke Evans

What are Best Practices? What are Bad Practices? Who Uses Best Practices? Why Bother? Acceptability Guidelines Published Best Practices Published Bad Practices Additional Best Practices Some Best Practices for Low Grade Deposits Interpretation Guidelines Big Bear Gold Deposit Example Conclusions Questions

May 1, 2013

By C. G. Harris, R. Sluyter

The purpose of an undercut is to undermine a block of ore which will then proceed to cave into draw holes just below the undercut. Undercut-ting is the final and most vital phase in the development of an ore block. Since its purpose is to undermine and induce caving into a block of ore, great care must be exercised to avoid premature caving by removing only enough rock to permit undercut development to proceed. Several undercutting methods, used over a twenty-year period, are re-viewed and their suitability is com-pared with ideal requirements.

Jan 1, 1960

By George J. Simandl, Donald F. Gunning

At the beginning of the 20 century, British Columbia produced a wide variety of quality dimension stone products for both domestic and foreign markets. The industry flourished until the 1930s when most of the producing quarries closed as a result of the Depression. During the 1990s, British Columbia experienced the resurgent North American dimensional stone production trend. The industry benefited from increased prospecting activity and from substantial new investment in processing equipment, particularly in the granite sector. These activities resulted in new quarry developments, the reopening of abandoned quarries such as on Granite and Fox Islands <www.quadrastone.com>, and a renaissance in downstream value-added activities. British Columbia has reestablished itself as an important, reliable and innovative source of high-quality stone products.

Jan 1, 2001

By P. Mengé

The covering of a hydraulically filled goethite pond is discussed from a geotechnical point of view. The characteristics of the goethite were defined in order to allow a detailed study of the procedure for the construction of the cover on top of the soft material and a verification of the stability of the cover and side slopes after construction. These characteristics and the main results of the studies are given, as well as the experiences and observations made during the execution of the work. Finally, the monitoring plan, during and after construction, is also discussed and some results are given. The &apos;Design and Construct&apos; contract form was used to allow the contractor to choose the optimum and most economical method to realize the closing of the pond, based on his experience with similar projects. The works were carried out between mid 2003 and the end of 2004. The paper will, amongst others, discuss the special method of working that had to be developed to allow the covering of the whole pond in a relatively short time period, without soil improvement methods such as vertical drains or stabilization by in situ treatment. Fill material was used to establish a platform on top of the soft material so that the cover liner and finishing layer could be installed on top of the fill layer. The &apos;floating roof&apos; principle was used; subsidences were allowed to occur during the installation of the impermeable top liner and soil cover.

Jan 1, 2006

By H. Scott Swinden

"ForewordA symposium on base metal deposits was held in Bathurst, New Brunswick, from June 10-13, 1990, sponsored jointly by the Geological Surveys Branch of the New Brunswick Department of Natural Resources and Energy, the New Brunswick Prospectors and Developers Association, and the Geology Division of the Canadian Institute of Mining, Metallurgy and Petroleum . Papers prepared for the symposuim are being published as a series of articles in the CIM Bulletin. This second paper (the first was by Fyffe, et al., in Vol. 83, No. 938) in the series presents an overview of the paleotectonic settings of massive sulphide deposits in the Dunnage Zone of Newfoundland with emphasis on volcanic geochemistry.ABSTRACTCambrian and Ordovician volcanic sequences of central Newfoundland, which record the history of the Iapetus Ocean, are prolific hosts to volcanogenic massive sulphide (VMS) deposits. Geochemical, isotopic and geochronological studies show that the vestiges of Iapetus in Newfoundland probably record a complex series of island arcs and back-arc basins that were marginal to, rather than part of, the main ocean basin of Iapetus. The geochemical and isotopic data provide a means of characterizing the tectonic environment of individual volcanic sequences, and allow us to identify a number of distinct tectonic environments in which VMS depositiontook place.Four tectonic environments have been identified as being associated with VMS deposition: (I) back-arc environments hosting VMS deposits include both N-MORB-type ophiolites (e.g. Skidder?) and volcanic sequences with oceanic island (or within plate) tholeiite characteristics (e.g. Great Burnt Lake); (2) primitive arc environments include both supra-subduction zone (SSZ) ophiolites (e.g. Betts Cove, Rambler) and volcanic/epiclastic sequences (e.g. Point Leamington, Duck Pond) and are characterized by abundant arc tholeiites, with lesser refractory lavas and rhyolites; (3) mature arc environments comprise dominantly thick felsic and mafic volcanic piles in the Buchans - Robert&apos;s Arm Belt (including the Buchans camp) and are characterized by dominantly calc alkalic basalt and andesite; and (4) continental rift environments occur in the Hermitage Flexure area (e.g. Strickland deposit) and are characterized by dominantly felsic volcanic sequences.Island arc environments are by far the most prolific hosts to VMS deposits. Patterns of VMS distribution in central Newfoundland show that similar tectonic settings may be recorded by very different stratigraphic sequences (e.g. both ophiolites and thick volcanic/ epiclastic sequences may record primitive arc rifting) and emphasize the importance of the rifting in VMS generation, irrespective of the details of the tectonic or stratigraphic setting. The ability to judge the prospectiveness of a volcanic sequence by using whole rock geochemistry to evaluate its tectonic environment may prove useful in area selection at the grassroots exploration level."

Jan 1, 1991

By I. Imris

The chemical industries are using different type of catalysts, which after application usually produced many tons heap of residues. One of them is cupric oxide catalyst with high content of copper and silica. The recovery of copper from the waste has become major interest from a viewpoint of environmental protection and recycling of resources. The thermodynamic analysis and experimental results suggest that the copper from cupric oxide catalyst can be extracted by plasma reduction process. By plasma reduction process the inert slag and copper with following chemical composition: 99.04 % Cu, 0,042 % Fe could be obtained.

Jan 1, 2007

By E. Brouillette

Difficult operating and mining conditions such as low visibility, difficult roadbeds, fast cycling, small openings, and sharp corners create high demand for LHD manoeuvrability and operator dexterity. Operator experience and patience is especially solicited to fill the bucket rapidly and efficiently and performance can be particularly affected by the skill level of individual operators. Teleoperation and automated loading are viewed as options to improve overall equipment and operation performance in certain mining conditions. Comparative statistical measurements of autoloading performance in different production environments at Noranda demonstrate an increase in bucket filling efficiency and a reduction in filling variance, allowing LHD operation to be more consistent and within manufacturer specifications. Consequential cost savings and productivity increases are demonstrated to be transferable to other mining situations.

May 1, 2003

By Kenneth G. Thomas

Since approximately 2003 we have witnessed the unprecedented escalation in commodity prices. Coupled with economic chaos following the 2008 economic downturn this has caused difficulties in controlling schedule, capital costs and operating costs for mining projects. Once again escalation has returned to commodity prices fuelled by growth in the BRIC countries especially China and Brazil. This is further exasperated by the missing generation of skilled technical personnel not graduating from universities in the 1980s and 1990s owing to depressed commodity prices. This paper examines the six tenets for successful project implementation.

Jan 1, 2011

By P. Bacher, L. Dubourg, M. Jahazi, G. Dezaise

Effect of friction stir welding parameters and natural ageing on weld properties are reported. Using a Taguchi design of experiment, attempt is made to systematically examine the influences of the welding speed, tool rotation speed, forge force, tilt angle and pitch ratio on the weld size and ultimate tensile strength of FSWed joints. One millimetre thick plates of AA7075-T6 were welded in lap joint configuration. Samples were characterized by optical microscopy, hardness and tensile measurements. Trends suggested by the results and directions for further investigation are discussed.

Jan 1, 2006

By Y. Y. Yemelyanov, S. S. Gudkov, A. V. Boldyrev, A. V. Bogorodskiy, S. V. Balikov

"A series of tests to optimize pressure oxidation- carbon-in-leach process (POX-CIL) of goldbearing flotation concentrate with the addition of sodium chloride and activated carbon were carried out. Flotation concentrate which was generated during primary ores concentration from a large Russian deposit was used for these tests. The tests were performed with different concentrations of sodium chloride. It was found that the required sodium chloride concentration for gold leaching was 5 g/L. The tests performed with different additions of activated carbon showed that the amount of activated carbon should be at least 6% of the concentrate mass. The rate of sulfides oxidation was 67.7–99.8 %. The highest gold recovery was 98.6 %.INTRODUCTIONThe majority of gold-bearing ores are recommended to classify as amenable to cyanidation and refractory. Processes at elevated pressures and temperatures have become increasingly important in base metals hydrometallurgy (Lodeischikov, 1999, 2007; Naboichenko, Shneerson, Kalashnikova, & Chugaev, 2009; Thomas, 2005).Current pressure autoclaves – cyanidation flow sheets are capital intensive due to numerous circuits and the use of environmentally-unfriendly sodium cyanide. The use of halide-based lixiviants during pressure oxidation of precious metals can be a promising technique for refractory sulfide goldbearing mineral raw material hydrometallurgical processing (Fleming, 2002, 2007, Kotlyar, Meretukov, & Strizhko, 2005).In this paper, we presented the results of the research on finding the optimum process parameters of pressure oxidation using an adsorbent for a refractory gold-bearing concentrate. A proposed flow sheet involves (Bogorodsky, Yelelianov, & Balikov, 2012):1. Gold-bearing sulfides oxidation followed by precious metals dissolution and the formation of gold and silver chloride complex;2. Reaction of the precious metals chloride complex with a carbon-based adsorbent;3. Precipitation of precious metals onto the adsorbent by EW and smelting of cathode precipitates into Dore bullions.This process allows POX of gold-bearing sulfides, precious metals dissolution and their precipitation on the adsorbent to be executed in one single vessel. This study found that the most suitable lixiviant was sodium chloride. Fleming (2002) suggested that in the presence of a halide-based reagent (e.g. chlorine- ion reaction), the dissolution of gold during POX is achieved according to reaction 1:"

Jan 1, 2016

By Maurice Lauzon

"Aerial surveys of the open pits have been conducted regularly at Lake Asbestos of Quebec, Ltd. -a subsidiary of American Smelting and Re-fining Company -since 1958. Ground controls are supplied by Lake Asbestos, and a topographic map of the pits at a scale of 1 in. to 50 ft., with 2-foot contour intervals, is obtained by aerial photography. The information from the topographic map is then transferred by the Lake Asbestos engineering staff to sections from which the volumes removed are calculated. Considering the size and complexity of the operation, this system has proved to be the cheapest, fastest and most accurate way of determining the quantities of rock and overburden removed. More than 11,000,000 tons of ore and waste are mined each year in three different pits. Further-more, the nature, shape and extent of the orebodies make it necessary to mine on many (up to eight) benches of a pit during a single year. In addition, there are sections of the pits where it is impossible or un-safe to survey the crest of some benches by standard ground methods. For these reasons, the tonnages obtained by truck count are checked and adjusted by aerial survey. These surveys are now taking place every six months. With this system, it is possible for a two-man surveying crew to look after all field work in the mine area."

Jan 1, 1967