Search Documents

By E. R. Hughes

Introduction Situated 182 miles east of Vancouver, on the Kettle Valley branch of the Canadian Pacific railway, the Princeton coal field is readily accessible to the Coast markets. The area covers approximately forty square miles and present indications are that the deposits should contain at least 300,000,000 tons of coal. Comparatively little development has yet taken place in this coal field. Since the commencement of recorded output, the collieries operating in this area have produced 1,640,518 tons of coal. The coal field proper includes only the Tertiary deposits adjacent to the town of Princeton and does not include the Coalmont or Nicola deposits. Production has never been on a large scale. The largest annual output from any property was 81, 780 long tons mined at the Granby colliery in 1940. Coal output was first recorded in 1909 and since that time fifteen properties are reported to have either mined coal or to have done prospecting or development work; of these, only two are presently active. However, none of the properties now inactive were closed because their coal resources were exhausted. The accompanying key map shows the extent of the Princeton coal field, and the location of the coal mines and prospects in this field General Geology The Princeton field is underlain by rocks of Oligocene age and is one of the series of more or less isolated Tertiary lake basins in which coal, or lignite, has been found in the interior of British Columbia. Resting on the Nicola group rocks of Triassic age, the Princeton sedimentaries consist of sandstones, conglomerates, shales, bentonite, bentonitic clays, and several seams of coal. Tertiary volcanics occur both above and below the stratified rocks and in places they have been thrust through the overlying measures. In some areas, the coal has been burned to a red ash as the result of vulcanism, while in other parts some of the moisture has been driven from the coal, thus improving the grade. The field can best be described by dividing it into two areas: the Southern area, lying to the south of the town of Princeton, where most of the mining has been done; and the Northern area, to the north of Princeton, where very little development has taken place.

Jan 1, 1947

By Michael S. Moats, Prashant Bagri

"In recent years with increasing concerns about energy consumption in hydrometallurgical processing, there is an ongoing attempt to use Catalytic Titanium Anodes (CTAs) for copper electrowinning. For this work, anodes with IrO2 - Ta2O5 coatings were prepared in the laboratory with the same total coating loading but varying the number of layers by changing the speed of withdrawal in dip coating. A second set of CTAs were fabricated on niobium, Ti Grade 1, Ti Grade 7 and Ti Grade 36 metal substrates. All the anodes prepared in the laboratory were characterized using standard electrochemical techniques and subjected to accelerated life testing. It was found that the coating would not adhere to the niobium substrate, the grade of titanium had a minimal to no effect on the life of the anode, and it is observed that as the coating speed slows, there is an increase in the electrochemically active surface area of the coating which seems to directly contribute to an increase in the Tafel slope of the anodes. There was inconclusive evidence on the effect of coating speed on anode lifetime.INTRODUCTIONLarge scale hydrometallurgical extraction of copper has become widely practiced over the last 40+ years. The hydrometallurgical route entails leaching, solvent extraction and electrowinning. With the increasing desire to process refractory sulphides like enargite and chalcopyrite through the hydrometallurgical route, use of hydro-processing of copper is expected to remain high.In conventional electrowinning, copper is deposited on the cathode and an inert anode is used for oxygen evolution. Presently, the most common anode material is rolled lead-calcium-tin and the cathode is 316L stainless steel (Robinson et al., 2013). This lead alloy is fairly inexpensive and is robust, providing lifetimes typically of 4+ years. The main drawbacks of lead alloys are their relatively high oxygen evolution overpotential, the need for cobalt in the electrolyte to reduce their corrosion, the contamination of cathode product by lead, and the generation of harzardous by-products (Hiskey, 1999)."

Jan 1, 2016

By J. W. Craig

THERE are, broadly speaking, three classes of refractories: acid, basic, and neutral. Fireclay, diaspore, silica, and the sillimanite group of minerals are included in the acid class, which for the most part are not very resistant to basic slags. The neutra! class includes chrome, graphite, and silicon carbide, while most important in the basic class are magnesite and dolomite. Although chrome is a neutral refractory, it has no sharp distinction from magnesitic refractoriness. The two are mineralogically (1) and chemically related, and there is available on the market a complete range of brick from straight chrome to straight magnesite. In many indus trial applications, one. type may be replaced by another. The present paper is confined entirely to such refractories. The following types of basic and neutra! brick, each sold under sorne special trade name, are available for use in Canada: (1) Burned chrome from crude ores (2) Burned chrome from treated ores (3) Chemically bonded (unburned) chrome-magnesite ( 4) Burned chrome-magnesite (5) Chemically bonded ( unburned) magnesite-chrome (6) Chemically bonded (unburned) high-iron magnesite (7) Burned high-iron magnesite (Regular) (8) Burned low-iron magnesite (9) Burned olivine-magnesite (10) Burned magnesitic dolomite-chrome (Magnecon) (11) Chemically bonded magnesitic dolomite-chrome (Magmecom) (12) Dolomitic brick

Jan 1, 1936

By Frédéric Bélanger, George P. Demopoulos, Pascal Coursol, Thomas Feldmann

"The use of scandium in industrial applications is expected to rise in the coming years, in large part due to the expected adoption of new, clean energy technologies such as solid oxide fuel cells or Sccontaining high strength aluminium alloys. Given that the supply of Sc is currently dominated by only a few countries (Russia and China) other sources for scandium extraction need to be investigated. This paper looks at different options for the recovery of scandium from waste solutions generated during the production of TiO2 pigments via the chloride process route. In particular, a direct solvent extraction (SX) approach and possible options for concentrating scandium before the SX step were investigated. It was found that the presence of Ti during solvent extraction causes severe formation of stable emulsions, which can complicate the successful application. This was particularly a problem after multiple contacts of the organic phase with fresh aqueous phase. On the other hand it was noticed that the presence of certain elements in the solution, e.g., iron, could possibly be utilized to concentrate scandium in a solid precipitate.INTRODUCTIONMany newly developed high-tech products depend on the use of chemical elements that are only produced in very small quantities. This can result in high and fluctuating prices, as can be seen from Figure 1, which may cause substitution with inferior alternatives, if possible at all (Reck & Rotter, 2012; US Dept. of Defense, 2013; Whittaker, 2011). One example is scandium (Sc) a member of the extended rare earth element family. There are only a few scandium ore deposits, but most Sc is produced from the processing of by-products of other metallurgical processes (Melcher & Wilken, 2013). Increasing demand for scandium metal and oxide (Sc2O3, scandia) is coming from its increased use in applications such as ceramic lasers (Li, Ikegami, & Mori, 2005; Rainer et al., 1982), high strength aluminium alloys (Lathabai & Lloyd, 2002) as well as solid oxide fuel cells (SOFC) (Thijssen, 2011). Especially, the spread of climate friendly SOFC’s, which are a commercial product today (Bloom Energy, 2014), is expected to be a main driver for future Sc2O3 demand. However, the rate of market penetration of this green technology depends on the availability of high purity Sc2O3 (>99.999%), since it specifically contributes to longer life-time and better safety of the SOFC’s (Bloom Energy, 2014; Irvine, Politova, & Kruth, 2005)."

Jan 1, 2016

By J. Cayouette, C. Bolduc, P. Blatter

"The LaRonde mill was commissioned in 1988 and began treating ore from the Penna shaft in 2000. The mill has been expanded to accommodate 7,500 t/day, but ramped down to 6,000 t/day since the deep extension began. The process recovers gold, silver, and base metals. In 2008, the Goldex plant began trucking gold-pyrite concentrate to a treatment plant feeding pulp to the LaRonde mill, increasing gold output by 40,000 oz. In 2009, the high-grade Lapa ore processing facilities were annexed to the LaRonde plant, increasing gold output by 120,000 oz. This paper outlines the metallurgical considerations related to the treatment of different ore types.RÉSUMÉ Le concentrateur de la mine LaRonde a été mis en service en 1988 et a commencé à traiter le minerai du puits Penna en 2000. La capacité du concentrateur a augmenté afin de permettre le traitement de 7 500 tonnes de minerai par jour, capacité qui est retombée à 6 000 tonnes par jour (tpj) depuis le début de l’extension en profondeur de la mine. Ce procédé permet de récupérer de l’or, de l’argent et des métaux communs. En 2008, l’usine de traitement Goldex a commencé à transporter par camion du concentré de pyrite et d’or vers une usine de traitement alimentant en pulpe le concentrateur de LaRonde, augmentant ainsi la production d’or de 40 000 onces. En 2009, les installations de traitement du minerai à haute teneur de Lapa ont été annexées à l’usine de traitement de LaRonde, augmentant la production d’or de 120 000 onces. Cet article passe en revue les considérations métallurgiques liées au traitement de différents types de minerai.INTRODUCTIONThe LaRonde metallurgical plant in the Abitibi region of Quebec, Canada, evolved into a mature milling site following expansions in 2000–2003, thanks to improved processes, manpower, and water treatment capabilities that better accommodate the complex constituents of the LaRonde ore. The ore requires a sequence of grinding, copper- lead and zinc flotation, and precious metals leaching, ending with a carbon-in-pulp (CIP) gold recovery. A portion (35%) of the tailings is sent back underground as paste backfill after being treated with the SO2-air cyanide destruction process. The tailings area has a dedicated cyanide destruction and metal precipitation area through which the used water passes before returning as recycled water. A biological water treatment plant was built in 2004 to address water toxicity in the final effluent. The water toxicity was the result of the high sulfide content of the LaRonde ore (from thiocyanate or stable cyanide species buildup) and the use of 90% recirculated water in the mill. The water treatment plant uses bacteria to transform thiocyanate into nitrates and precipitate phosphorus from the water before it is discharged into the environment."

Jan 1, 2017

By J R. M Hutcheson

Advocate Mines Limited came into initial production on June 30, 1963, with an annual capacity in excess of 60,000 tons of high-quality chrysotile asbestos fihres, thus strengthening Canada's position in world production. The history of this development is traced from discovery through initial exploration, financing, orebody delineation and evaluation, pilot-plant production and product evaluation, construction of the plant, construction of deep?-sea shipping facilities, provision for a closed shipping season, and provision for the remoteness and for the lack of services, through to realization of full production capacity. The many unique aspects of the project are given special attention, particularly in the light of the first year of full-capacity operation. The marketing of the products in a highly competitive world market is reviewed, with special emphasis on product evaluation, quality control and the shipping of high-quality products to consumers throughout the world. C ANADA'S newest asbestos producer, Advocate Mines Limited, is located at the north end of the Burlington Peninsula, White Bay District, Newfound-

Jan 1, 1965

By Steve Custer, Chris Bennett, Patrick Garretson, Glenn Dobby, Jacques McMullen

"Barrick Gold is in the process of expanding one of its grinding circuits at the Goldstrike property as a response to both increasing ore hardness and increased ore sensitivity to finer grinding as it relates to gold recovery. The plant currently operates with two parallel grinding lines, each with a SAG mill, a pebble crusher, and a ball milling arrangement. As part of determining what additional equipment was to be required, a CEET evaluation program was conducted (CEET is an acronym for Comminution Economic Evaluation Tool). The work included: Development of a hardness ‘model’ for the ore body, as described by SAG Power Index and Bond Work Index;Site benchmarking surveys to fine tune the SAG and ball mill calibrations within CEET;Conducting CEET studies to examine the process options;Comparing CEET results to standard grinding circuit design techniques.The recommendation of the study, presently being implemented, is the installation of an additional ball mill on one of the two grinding lines. This paper reviews the sizing techniques applied, providing a CEET case study for circuit performance analysis and circuit design. OVERVIEW OF COMMINUTION AT GOLDSTRIKEOre feeding the autoclaves at Goldstrike are first processed through two parallel grinding lines. Both lines use SAG mills with cone crushing of pebbles followed by ball milling. A summary of the key circuit parameters is provided in Table 1. Line 1 primarily processes underground Meikle ore, although when no Meikle ore is available, it processes open pit Betze ore. Line 2 processes Betze ore exclusively. The Mill Line 1 P80 objective for Meikle ore is 74 microns. According to the recovery optimization analysis, a P80 of 90 microns was recommended for Betze ore. The potential however exists to perform co-mingling of both ore types and feed the higher grade Betze ore to Line 1, in which case the P80 of 74 microns would be retained."

Jan 1, 2001

By J. G. Kelly, C. P. Brown

"In June 1983 a new borehole hoisting system was commissioned at Sherritt Gordon's Fox Mine. Twelve hundred tons-per-day of ore from the 2600 and 2800 levels are being hoisted to the 2000 level through an 8-jt diameter bored winze. This new method replaces the diesel truck haulage system which had been in operation at the mine since 1975.A study was initiated in 1980to determine the most effective method of achieving the required production. The study examined several hoisting alternatives including: expanding the existing trucking system; converting to electrically -powered truck haulage; and deepening the skip compartments of the existing main shaft. The alternative selected as the hoisting method most suited to the requirements was borehole hoisting.Development of the new system commenced in April 1982. Underground excavations included 700 feet of 8-ft diameter borehole, a hoistroom and headframe, storage bins, and a grizzly and rockbreaker station. Equipment installations included: a 5-ft diameter double-drum Nordberg hoist; a counterweighted Kimberley-type skip; two rockbreakers; and the steel sets in the winze. These installations were completed in June 1983. Some problems were encountered after the initial commissioning but these were solved, and since August 1983, the system has proven that the designed capacity is achievable within expected costs."

Jan 1, 1985

By Terence M. Gordon, Mati Raudsepp, Gregory M. Dipple

Four methods of measuring mineral abundance in a rock are examined for their potential in assaying for high-tech industrial minerals. One method uses X-ray powder-diffraction data and the other three rely on whole rock chemical data and information on mineral assemblages and mineral compositions. All four methods were employed to estimate wollastonite content in diamond drill core of skarn collected as part of an exploration program and are compared to visual estimates of wollastonite content from core logs. These techniques for assaying wollastonite span a considerable range ofaccuracy and expense, and combined, define a non-linear relationship between these variables. Accuracy increases rapidly relative lo expense up to total costs of about $50 per analysis. Assay methods in the $50-100 per analysis range have associated errors of 5-10% relative and probably suffice for most exploration programs. Improvements in accuracy above this level require a much larger investment. The most expensive assay technique (-$300 per analysis) yields the most accurate measurement of grade (relative error -1%). Its application may best be limited to periodic checks on other assay techniques and for fine-tuning ofmineral separation procedures.

Jan 1, 2001

By P. Cheung, J. Gulyas, R. Clary

Over the past 50 years, the use of autoclaves in the metallurgical industry has evolved from final metal recovery (hydrogen reduction) and purification (sulphide precipitate oxidation) to treating whole ores and concentrates. Recent process developments, such as the use of autoclaves for laterite leaching, have necessitated higher temperature and pressure operations, which in turn have seen marked advancements in technology and manufacturing capabilities to keep in step with process demands. This paper will discuss the advances in technology in terms of design, materials and construction of autoclaves and liners, typical dip tube design and geometric layout. This paper will also address specific auxiliary equipment, such as acid and steam injection systems, and components, such as agitator seal systems.

Jan 1, 2004

By Karl J. C. Harries

"3.1. INTRODUCTIONThis chapter discusses briefly the common law concepts of fiduciary relationship, constructive trust, and breach of confidence. Following a discussion of confidentiality agreements, the last section of the chapter compares and comments on two common law cases, the LAC Case and the Metalore Case. Civil law readers should not ignore this chapter or § 3.5. the comparison as, to a large extent, the concepts and comments are universal, even though the procedures for applying them may vary.1It should be appreciated that, regardless of the legal system, if the Court sees that a wrong has been done, it will attempt to right that wrong, either by awarding monetary damages against the wrong-doer to compensate the injured party or by attempting to make the injured party whole again by such means as negating an agreement (as in the Metalore Case) or returning property to a wronged party (as in the LAC Case). The methodology for accomplishing either of these results will vary with the jurisdiction, and the two are not mutually exclusive.These two Ontario cases have been chosen, not because they are the only ones available – they certainly are not – but because both are relatively well known within the minerals industry and they deal with problems that may face any explorationist (although it is to be hoped that the facts of the Metalore Case do not represent “normal” behaviour). Each judgment offers useful guidelines, as well as insight into a judge’s approach to problems, the type of information he expects to receive, how his mind works, and, particularly in the Court of Appeal judgment in the Metalore Case, how he might reason through and “justify” his decisions.3.2. SOME LEGAL CONCEPTS In order to appreciate some of the matters discussed in this chapter, it is necessary to have some idea of the common law considerations of fiduciary relationships, constructive trust, and breach of confidence."

Jan 1, 2003

By J. D. Bateman

DURING the summer of 1942 several chromite deposits were discovered in the Lac du Bonnet district about eighty miles northeast of Winnipeg. The deposits are confined to the Bird River complex, a folded composite sill of basic and ultrabasic igneous rocks of early Precambrian age that lies to the north of Bird river (1). The outcrop of the sill represents the trace of an easterly plunging anticline, the south limb extending from the northeast bay of Lac du Bonnet eastward to Bird lake, and the other limb, 6 to 12 miles north, lying between Maskwa river and Euclid lake. The south limb of the sill is 20 miles long, and the northern counterpart 15 miles; but its continuity is interrupted by faulting and by the intrusion of younger granite, so that the total length of outcrop of both limbs does not likely exceed 25 miles. The sill is intrusive into early Precambrian greenstones and associated sedimentary rocks. The chromite discoveries have been made at several localities on both limbs of the sill, and in each case at the same geological horizon. The sill comprises an upper layer of hornblende gabbro and a lower layer of serpentinized peridotite, and altogether is from 500 to 3,500 feet thick. The chromite zone is within and near the top of the peridotite layer, and thus about midway of the sill, both of the limbs of which stand nearly vertical. This geological relationship was established early in the exploration of the initial discoveries and served as the basis for successful predictions of later discoveries. The chromite zone probably persists throughout the length of the sill, but its width and chromite content are not everywhere the same. The initial exploration along both limbs of the sill has shown a combined total length of about 12,000 feet of chromite ore varying in width from 6 to 12 feet. In many places the overburden is thick and obscures the continuity of the chromite zone; but as investigation proceeds the known deposits will be extended and new ones will be found. Thus, although a total length of 12,000 feet of ore has been investigated up to the present time, there is an indicated length of approximately 31,000 feet along which the ore is more than 4 to 5 feet wide. This estimate is based on geological considerations and represents a total tonnage in the order of 15,000 tons per vertical foot of depth.

Jan 1, 1943

By C. Nikolic

A process utilizing ozone for the precipitation of cobalt from nickel sulphate liquors containing ammonium sulphate has been developed. Best results were obtained using nickel carbonate to maintain solution pH at 5.0 to 5.5. Work was performed both in column and stirred-tank reactors. Variables studied included neutralizer type and concentration, NH4+ concentration, temperature, Ni++ and Co++ concentration, per cent O3 in the O2 carrier gas, O3 input rate and agitation. The over-all rate of cobalt rejection increased sharply with increasing agitation and ozone concentration in the gas phase, reflecting relatively slow transfer of ozone from the gas to the liquid phase.

Jan 1, 1978

By J. C. Keenan

Company-community agreements are widely considered to be a practical mechanism for recognising the rights, needs and priorities of peoples impacted by mining, for managing impacts and ensuring that miningderived benefits are shared. The use and application of company?community agreements is increasing globally. Notwithstanding the utility of agreements, the gender dimensions of agreement processes in mining have rarely been studied. Prior research on women and mining, however, does show that women are often more adversely impacted by mining than men, and face greater challenges in accessing development opportunities that mining can bring, however there is currently little to no guidance for companies, government or communities in terms of bringing a gender perspective to the fore in mining and agreement processes. While it is undisputed in human development literature that investment in women and sensitivity to gender delivers long-term health, education and local development outcomes, a number of key factors remain unexplored in debates about mining and development. These include: women?s participation in agreement processes, the gendered distribution of agreement benefits, and the extent to which impacts and benefits influence (either positively or negatively) women?s development and economic inclusion. This paper presents the results of an applied research project undertaken by the Centre for Social Responsibility in Mining (CSRM) at The University of Queensland and funded by a partnership between the Minerals Council of Australia (MCA) and the Australian Agency for International Development (AusAID). The project sought to connect with practitioners who had been directly involved in agreement processes to hear grounded perspectives on the interaction of gender dynamics and agreements, and connect those experiences with the broader literature. Findings from this study have implications for the role of companies and governments in promoting gender equality and empowerment as part of their commitments to sustainable development. A key challenge for companies will be navigating the territory of cultural norms and gender equality. The authors argue that without consideration of the gender perspective, and appropriate responses, mining agreements may not be inclusive or representative and may exacerbate gender inequalities and fail to contribute to long-term sustainable development.

Aug 1, 2013

By J. A. Allan

OCCURRENCES of salt in Alberta have been mentioned and described by the writer in 1929 (l) and by Cole in 1930 (2). Brine springs occur at a number of places along the valley of Athabaska river north of latitude 56 degrees, and also on the south margin of Salt prairie, twenty-five miles west of Fitzgerald in the vicinity of the 60th parallel of latitude, which is the boundary between Alberta and the Northwest Territories. These salt springs were visited by Sir James Richardson in 1820, and in the same year D. W. Harmon stated that " ... clown Salt river there are several places where almost any quantity of excellent dean white salt may be taken with as much ease as sand along the seashore" (3). One hundred years later, in 1920, when the writer first visited these springs, the "dean white salt" which had accumulated about the springs was about 400 tons ( 4). This paper deals with a thick deposit of rock-salt which has been proved by drilling in the vicinity of McMurray. Particular attention will be given to a well drilled at Waterways early in 1936 by Industrial Minerals, Limited, when a continuous bed of rock-salt was penetrated with a thickness of 199 feet. As this paper is being presented, a salt plant is being completed and a production well is being drilled at the plant. < is salt deposit is in the vicinity of McMurray, close to the junction of the Clearwater and Athabaska rivets, in township 89, range 9, west of the 4th meridian. McMurray is about 240 miles northeast from Edmonton. As shown on Figure 1, Clearwater river, which rises at Methy portage, in Saskatchewan, enters Athabaska river at McMurray. Some three miles above the mouth of Clearwater river, the Hangingstone enters from the southwest. Waterways, where the latest salt development has taken place, is situated at the end of the Northern Alberta railway, a distance of 304 miles from Edmonton. This railway reaches the bottom of the Clearwater valley at Draper station, about 3 miles east of Waterways and near the mouth of Deep creek. The Draper bituminous sand plant is approximately half a mile east of Draper station. About one mile south of the townsite of McMurray, Horse river enters the Athabaska from the east.

Jan 1, 1937

By B. Voyzelle

The deterioration of highway and bridge infrastructure has received considerable attention in recent years because of the billions of dollars needed for repair and rehabilitation. A major factor contributing to this problem is the corrosion of steel reinforcement. Reinforcing steels with good corrosion resistance and relatively low price are therefore essential for maintenance, cost reduction and service-life extension of the steel-reinforced structures. This article describes the development of low-alloying steels that offers good corrosion resistance with reasonably low cost. Topics include steel microstructures, mechanical properties, corrosion performance, industrial applications and economic aspects.

Jan 1, 2005

By O. G. Olvera, L. S. Quiroz-Castillo, P. J. Valenzuela-Guerrero, D. G. Dixon

The effect of sulfuric acid concentration on the extractions of arsenic and copper in the catalyzed batch leaching of an enargite concentrate was studied. The acid concentrations studied were 60, 45, 30 and 15 g/L. The experimental series yields maximum copper extractions of 96 to 98% in an interval of 81 - 185 h leaching time for 60 - 15 g/L initial sulfuric acid concentration; all the copper extractions plateaued after these values; the rates and plateaus of copper extraction are increased with higher acid concentrations. Arsenic extractions reached maximum values of 89% in 57 hours, 57% in 49 hours, 33% in 25 hours, and 25% in 112 hours respectively; these maximum values were followed by a steep decrease in arsenic concentration, which indicates a precipitation event occurs in the process. According to the literature and process conditions, the arsenic precipitates obtained are iron arsenates similar to scorodite. The stability of the residues was tested using the Toxicity Characteristic Leaching Procedure (TCLP) from EPA; the residues for the four concentration levels passed the TCLP test, reporting arsenic leaching values below 1 mg/L.

Jan 1, 2014

By G. F. Carr

"IntroductionFLUORSPAR has been found at several •localities in Newfoundland, but all the commercial deposits discovered to date are in the vicinity of St. Lawrence, a town on the southeast coast. Most of the veins are within six miles of St. Lawrence harbour, and between sea-level and an altitude of 400 feet. The St. Lawrence Corporation of Newfoundland, Limited, and Newfoundland Fluorspar, Limited, a subsidiary of the Aluminum Company of Canada. Limited. are the two producers.With the arrival of 1953, the St. Lawrence area entered upon its twenty-second •consecutive year as a producer of fluorspar. Production has increased more or less steadily during this period, as is shown by the fact that approximately one-half of the total shipments to date have been made during the past six years. Between four and five hundred men are employed by the industry, and more than $1,250,000 was paid out in wages and salaries during 1952. Shipments during that year reached an all-time high of 81,283 tons valued at $2,484,943, compared with 67,925 tons valued at $1,966,477 in 1951 (1).As a result of an agreement made in July, 1952, with the United States Defence Materials Procurement Agency, production of the St. Lawrence Corporation, Limited, and St. Lawrence Fluorspar, Incorporated, an affiliated company, will •be increased by .approximately 50,000 tons of acid-grade fluorspar per year. The contract extends over a period of four years, or until 150,000 tons of acid-grade concentrates have been produced."

Jan 1, 1954

By W. L. Sherwood

Present conventional techniques for primary steelmaking in both integrated and non-integrated plants are outlined. 'Direct reduction' alternatives are reviewed and categorized according to the nature of the product produced, with particular emphasis on the limited number designed to yield steel as the end product. A proposed new technique, referred to as the Sherwood Process, is described in some detail as a new combination of selected features from the prior technology. This process is in-tended to realize, in integrated operations, the result of continuons steelmaking directly from the ore in a single plant and, in non-integrated operations, continuons steel-making from a metallic charge of scrap, sponge iron or pig iron. Prominent features are continuons processing in elongated, horizontal, rotary furnace equipment, controlled direct heating of each process stage and, for the over-all integrated process, a size separation for removal of excess solid reductant and other waste just prior to the melting step. Material and energy balances are presented as well as exemplary cost data. Reasons for selecting this particular combination of process elements are dis-cussed.

Jan 1, 1968

By K. W. Edwards

The formulation of a theoretical basis for the evaluation of in-situ coal through the use of geophysical logs is outlined. This involved the development of an approach to the interpretation of resistivity in environments having multiple conductive and non-conductive components. Utilizing this approach and other conventional interpretation techniques, a program was developed yielding accurate determinations of the in-situ percentages of coal, water and ash for the evaluation of coal deposits. Basic information obtained from the CWA program can be utilized in numerous aspects of total mine planning . Some examples of the practical application of this method are included.

Jan 1, 1978