Search Documents

By G. Lodewijks

This paper explores the savings that can be achieved in the energy consumption of belt conveyors used in mines by changing the conveyor components, the operational parameters of the system or the belt properties. First the concept of energy savings is introduced by looking at the energy consumption of belt conveyors from a theoretical point of view. Also methods for the calculation of the power consumption of a belt conveyor and the associated emissions are presented. Two case studies are presented in which the effects of the change of the operational parameters of the system, in this case the belt speed, and the belt properties, in this case the application of aramid products in the belt, are presented.

Aug 1, 2013

By S. P. Lowe

Introduction In the following pages a general description is presented of the concentrator and cyanide plant of the Hudson Bay Mining and Smelting Company, Limited, at Flin Flon, Manitoba, together with some account of the steps which have led to the adoption of the present practice. For an account of the preliminary test-work and pilot-mill operation, the reader is referred to a recent paper by R. E. Phelan on the History of Flin Flon Mine up to Construction (1). Additional notes may be found in a paper which the writer presented at the Annual Meeting of the Institute in 1930 (2). The first ore was crushed in the present plant on July 1st, 1930, and the first ball-mill was started one month later, on August 1st. Since that time, production has been continuous with the exception of one month lost during a strike in the summer of 1934. There have been no major changes in equipment or methods of treatment since the present plant was built, but many minor changes have contributed to the improvement in results obtained and to the increase in capacity to the large tonnage now being milled. The accompanying flow-sheets indicate the equipment used in the several plants, with the average life and repair cost. As originally built, the concentrator was to treat 3,000 tons per day, but the capacity has been increased to 4,400 tons. The methods adopted to make possible this increase in tonnage will be referred to below. It was the intention to produce two classes of ore: (1) a heavy sulphide, and (2) a disseminated ore. The mill was consequently divided into two sections, each adapted for most efficient treatment of one particular type of ore. However, it was soon found that it would be impossible to mine the two classes of ore separately, so it was decided to treat open-pit ore, which varies greatly in character, in the sulphide section, and underground ore, which is fairly constant, in the disseminated section. This segregation is still maintained.

Jan 1, 1935

By V. A. Cooney

Introduction For the compliment paid me by the Institute's kind invitation to speak this afternoon, I am very grateful. For the astuteness of your officers in determining that encouragement should be given, through the medium of a paper, towards accident prevention in coal mines, the coal industry cannot but be grateful. Some day, and let us hope soon, a more developed paper may supersede this one. In the meantime, if some knowledge of what one coal field has been able to accomplish, even in the initial stages of its effort, will induce other fields and other sections of the mining industry to launch similar experiments, much good will result and a more developed dissertation on the subject will make its appearance.

Jan 1, 1946

By W. P. Campbell

Introduction OWING to the necessity of curtailing the length of this paper, nothing like an exhaustive treatment of the subject will be attempted. Instead, merely a few aspects will be considered, viz., water trouble in wells, sampling of waters, analysis, methods of reporting analysis, and the comparison of a few typical waters. The waters discussed will not be confined to those occurring in areas where oil or gas has already been found, but will include samples from areas in which drilling is being carried on in the hope that oil or gas may be found, i.e., from unproved fields. The Water Problem The problem of dealing with water encountered in oil and gas producing areas has engaged the attention of petroleum engineers from the early days of the industry. Water was not always considered a menace to oil sands; indeed, a certain amount of it was considered beneficial in some areas, but if such exist today they are very exceptional. In some fields, the problem is more acute than in others, and at times has baffled all attempts to solve it satisfactorily. Wells have been brought-in with promise of good production, but after a brief period have 'gone to water'. Whether ?it has always been a case of poor engineering in the form of unsuccessful water shut-off of 'top' or 'bottom' water, or because 'edge' water was present and water and oil were in such close contact it was impossible to remove the one without the other, is hard to say.

Jan 1, 1929

By N. C. Karmakar, Y. V. Rao, M. Aruna

No one can properly work without sufficient light and this is especially so in mines where conditions are difficult. Artificial lighting is very important for the night shift to provide a safe and efficient working environment, which must be evenly illuminated with no obvious dark spaces and a minimum amount of glare. During an illumination survey of a large mechanized surface mine, it was found that the illumination level varied and was not uniform throughout the length of the road; it was high at one side of the road instead of at the centre. There were also different combinations of lamps, with angles of light arm varying from 35º to 70º. In this respect, an experimental study was carried out with a fabricated telescopic light pole to uncover the optimum design parameters of lighting installations. The analysis was done by plotting isolux contours for fixed installations and drawing graphs for various combinations of luminaries, reflectors, light arm angles, and height of lanterns by plotting the horizontal angle of the light arm along the abscissa, and the contour area along the ordinate. The study revealed that the design parameters of the lantern are mainly dependent on the type of luminaires. It was revealed that the pot reflector with a combination of tubular bulbs produces a wide distribution of light, and contributes towards a reduction of luminaries when installed in longer roads.

Jan 1, 2005

By Limao Zhang

This paper presents a novel model to assess the risk of adjacent buildings in tunnelling environments based on Extended Cloud Model (ECM). ECM is an organic integration of Extension Theory (ET) and Cloud Model (CM), where ET is appropriately employed to flexibly expand the variable range from [0, 1] to (-8, +8), and CM is used to overcome the randomness and fuzziness during the gradation of evaluation factors. The risk level of a specific adjacent building is assessed by the correlation with the cloud models. A confidence indicator ? is proposed to illustrate the rationality and reliability of evaluating results. Ten buildings adjacent to Wuhan Metro Line Two (WMLT) are randomly chosen among hundreds of adjacent buildings for a case study. Results have proved to be consistent with the actual situation. Compared with other traditional evaluation methods, ECM has been verified to be a more competitive solution with high calculation accuracy, wide adaptability, as well as simplified computer programming. There are no stringent requirements on the quantity of training data during the modelling process, and the original data can be directly entered into ECM without a normalization procedure, avoiding the potential information loss. ECM can be offered as a decision support tool for the risk assessment in urban tunnelling construction and worth popularizing in other similar complicated projects.

Aug 1, 2013

By James F. Archibald

A research effort has been undertaken, under WSIB sponsorship, to characterize the support capabilities of conventional and innovative spray-on lining materials for mitigating dynamic failure effects created by simulated rockbursts. Conventional spray support media, such as shotcrete and fibrecrete linings, and a variety of new spray-on lining materials (TSL?s), typically polymer-type thin coatings, were subjected to simulated rockburst influence. For baseline comparison, conventional rockbolt and boltand- mesh support products were also evaluated. Observation of lining performance was undertaken through completion of field scale support and rock detonation trials. Controlled blasting tests were conducted at the Queen?s University Explosives Laboratory to examine the effectiveness of the variety of surface coating agents for modifying dynamic rock spalling processes. All tests were performed upon largely undisturbed and homogeneous rock materials in highly repeatable fashion. Both conventional and innovative TSL-type surface lining materials were subjected to ?rockburst? exposure in rigorously-controlled blast trials. All blasts were observed seismically and photographically to provide detailed information concerning rock motion, surface fracturing, ejected fragment motion and support liner survivability characteristics. These material comparison trials were performed to assess the relative effectiveness of a wide range of currently-available area support techniques for suppressing hazards associated with dynamic rock ejection. The results of this study validates that thin, sprayon linings may be equally as effective, and often better, than conventional support materials at mitigating rockburst or like damage in highly stressed mine environments.

May 1, 2003

By Hamidreza Soltanzadeh

The injection of CO2 into a reservoir or aquifer can potentially result in deformation, induced fracturing and fault reactivation in the injection zone and/or the rocks that surround it. This paper reviews the data collection and geomechanical analyses performed to assess these potential hazards for the Heartland Area Redwater Project (HARP), in which CO2 sequestration is being considered in a carbonate (Leduc Formation) reef. A three-dimensional mechanical earth model (3D MEM) was developed using available geophysical log data from several wells. The geomechanical response to CO2 injection was studied using a finite element numerical model based on the 3D MEM and pore pressure distributions predicted using a reservoir simulator. The modeling results suggest that the potential for induced fracturing and fault reactivation is low and the maximum predicted ground surface heave is less than 2 cm. Sensitivity analyses conducted with a 2D geomechanical model that was extracted from the 3D model confirm that this conclusion holds true even when a reasonable measure of uncertainty in rock mechanical properties, ambient pore pressures and horizontal stress magnitudes is accounted for.

Jun 1, 2012

By F. W. Tregarthen

"This paper gives a brief description of the methods used to form and implement the present planned maintenance program. The system is designed to assist plant personnel in their task of controlling a large work-force and maintaining the many and varied types of equipment used in a mining and concentrator operation. The types of reports and methods used in scheduling and work-loading are described. General built-in flexibility is derived from computer assistance to the Central Planning Group."

Jan 1, 1971

By Xueyi Guo

The total production of nonferrous metals in China is 31.35 million tons in 2010, which ranks first in the world for the past ten years. Large quantities of solid wastes including slag, residue, ash, and dust are produced every year in the production of nonferrous metals. These secondary resources are renewable, not only contain abundant valuable metals which can be recycled by metallurgical processing, but also could eliminate the pollution to the environment. In this paper, the status quo of the main nonferrous metals recycling in metallurgical industries in China was summarized, and the future development of waste processing and resource recycling was prospected.

Jan 1, 2011

By David Burchell

Duckbill mining is probably the simplest method of loading coal mechanically at the face in underground mines. It is a means of reducing the amount of physical labour required to produce a ton of coal. In effect, it is merely shaker conveyor mining brought up to date with the addition of a self-loading head or 'duckbill' on the end of the conveyor line. Any mechanical device used to load coal is a means of supplanting the human muscles as the medium for getting the coal off the floor into the transportation equipment. There can be no argument with the conclusion that a man can lift so much and no more. He can load more tons of coal on a low conveyor, because the lift is less, than he can in a pit car two, three, or even four feet high. Thus it follows that, if the lifting operation is entirely eliminated, the man should be able to produce even more coal. A mechanical operation is essentially a multiplication of physical strength. Although there are various ways in which coal can be loaded at the face by mechanical means, there is, perhaps, none more adaptable than shakers equipped with duckbills. This is particularly true for thin seams and in mines having heavy, tender top conditions which require close timbering. However, as we are discussing duckbill mining, we will make no further reference to any other type of equipment. The first, and to date the only, mine in eastern Canada to adopt a system of mechanical loading at the face is the Franklin mine of the Bras d'Or Coal Company, Ltd., at Bras d'Or, N.S. An experimental Goodman shaker conveyor with a self-loading head, or duckbill, was installed in this mine in 1940. Since that time other units have been placed in operation so that, today, this mine is completely mechanized. The method of operation 1s room-and-pillar. The operation is carried on in a 42-in. seam, which lies 420 feet beneath the Sydney Main or Harbour seam in the Sydney Mines basin. The slopes bear N.25 30'E., dip 10 per cent seaward, and are about 6,000 feet in length. The physical conditions of this seam do not make it particularly adaptable for complete mechanization as it contains a large amount of foreign material, such as clay intrusions or wash-outs and iron pyrites. These clay intrusions, known locally as 'troubles', vary in thickness from a few inches to as thick as eighteen feet and usually replace the coal to the full height of the seam.

Jan 1, 1947

By Yoginder P. Chugh

This paper discusses design of sprays systems for dust control around a continuous miner (CM) in about 4.2 m (14 ft.) high mining areas with about 1.0 m to 2.0 m (3-6 ft.) of out-of-seam dilution mining. The challenges included low air volumes and velocity at the end of the line curtain, dust produced from out-of-seam dilution rock being very fine with 50% of the particles less than 10 micron, poor capture of aerosol through scrubber suction inlets, dust escaping through the sides of the loading pan in mining high areas, overloading of dust-laden air in the wet-scrubber, and dust rollback toward workers. The challenges were resolved through CFD modeling of airflows; improved line curtain installation, redesign and varying the spatial locations of spray systems as compared to low mining height areas. Water sprays on CM is the primary engineering control for dust control in coal mining. In 2010, the authors developed several spray system concepts for dust control (Chugh, Patwardhan, Gurley, & Hirschi (2009), Chugh & Gurley (2009), Chugh 2012). These included increased contact time between dust particles and water droplets, improved potential for the dust aerosol to be sucked in through suction inlets, and reduced dust-roll back to the operators and workers. CFD modeling was used to understand airflow patterns around mining areas and to identify spatial locations for sprays to minimize dust exposure of CM operator (CMO), haulage unit operator (HUO), and workers downwind of the operating CM in the last open crosscut (LOXC). Face area ventilation plays a key role in dilution and removal of dust generated by mining operations. High mining heights and large pillar sizes associated with longwall mining reduce the air volume reaching the face area to achieve good dust dilution.

Aug 1, 2013

By J. -P. Lempainen, K. Haavanlammi, K. Valkama

The Outotec nickel matte chloride leaching process is especially suitable for small capacity standalone nickel refineries. The matte is leached with hydrochloric acid and oxygen in multiple steps in atmospheric OKTOP® reactors. Oxygen feed prevents reductive conditions and hydrogen formation in the leaching process. A sufficiently high acid concentration keeps the iron dissolved in the solution. The iron is removed after leaching by precipitation and the pregnant leach solution continues to metals recovery. The metals recovery from the chloride solution is done by solvent extractions, where ammonia is used for pH control. Copper and nickel are stripped from the organic phases into sulphate solutions. Metals can be recovered from the purified solution by conventional electrowinning. Other alternatives are precipitation or hydrogen reduction processes. The ammonium chloride in the solvent extraction raffinate is regenerated into ammonia. The calcium chloride solution from ammonia regeneration is routed to acid regeneration where sulphuric acid is added and ultra-pure gypsum is precipitated. The hydrochloric acid solution from this step is recycled back to leaching. The process yields good overall metal recoveries and expensive

Jan 1, 2014

By P. N. Calder, D. B. Apel, S. D. Butt

Mine-wide (MW) microseismic systems use widely spaced transducers to determine the source location and parameters of stronger microseismic events, while high frequency (HF) systems use fewer transducers to monitor local areas for the weaker events that can precede stronger events. Previous monitoring at the Creighton Mine indicated that an HF transducer located 120 m away from an active stope recorded two types of activity in response to production blasting: the first occurring at the same time as the production blasts and associated with the passage of the direct seismic waves from the blast through the local area, and the second occurring several hours later and associated with the arrival of a slower moving stress change through the rock mass (which was identified by the mine’s MW system). Interpretations of locally increased stress levels, based on analysis of the recorded HF events, correlated with the nearby occurrence of two strong seismic events. These results were applied to a similar monitoring trail at the Kidd Creek Mine where the transient stress changes induced by several development blasts were monitored. It was observed that increases in HF activity corresponded with the occurrence of MW events near the transducer location, and that fewer HF events were recorded the longer this occurred after the blast. Local geological features appeared to influence the number and occurrence of both HF and MW events.

Jan 1, 2000

By M. W. Bates, A. L. Mular

This paper, based on work carried out at Queen's University, describes the development and use of mathematical models of the parallel cyclone classifiers being used in the Strathcona mill of Falconbridge Nickel Min.es Ltd.

Jan 1, 1971

By E. O. Magnusson

THE orebodies of the Preston East Dome mine show a considerable variation in size,? shape, dip, and ground condition. They vary from small and large irregular masses being mined by shrinkage, cut-and-fill, and square set-and-fill mining methods to narrow veins being mined by open stoping. Standardization of mining operations has necessarily been difficult. This considerable variation in mining condition prompted the development of a bonus system which would give more equitable bonus payments through-out the mine than those obtained by the usually accepted methods of calculating mine bonus. PRINCIPLES ON WHICH THE SYSTEM IS BASED Under an incentive bonus system, performance (efficiency) and a price per unit of work done are inter-related. It is in the application of this? principle to working conditions .in the Preston East Dome mine that the system to be described differs from the standard methods of calculating mine bonus. It was found that the method of paying a fixed price per unit of work done, under the 'contract' system, gave satisfactory results in development, less satisfactory results in timbering, and results which were not satisfactory in stoping. Under the fixed price system, bonus payments, in timbering and stoping particularly, were very erratic and did not necessarily represent fair payment for the work done. A fixed price in development is satisfactory because the work done, and the conditions under which the work is done, are uniform. The drilling and blasting cycle is completed in one shift, the size of heading is con-trolled, and a minimum number of holes are required in order to obtain a satisfactory break. The performance possible under these conditions has been found to be confined to a fairly narrow range. By performance in development is meant the efficiency of the working crew as expressed in terms of the two variables of feet of advance per round and pounds of ex-plosives consumed per foot of advance. A change in rock formation, how-ever, may alter to a marked degree the performance possible, quite independent of the skill and energy of the working crew. The changes in working conditions that affect development performance from the standpoint of bonus calculation are usually easily apparent and are satisfactorily met by establishing several fixed prices.

Jan 1, 1944

By O. A. Carson

"IntroductionTHE ZINC-BASE die casting alloys in common usage contain approximately 4 per cent aluminum as the major alloy element. In addition, they contain about 0.05 per cent Mg .and may• have a small amount .of copper. These are usually the only •elements intentionally present.Small amounts of some impurities have been shown to have a deleterious effect on the properties of these alloys and therefore the impurities are kept low by starting with '99.99%' zinc.The reasons for holding the aluminum content at 4 per cent are not clear. Some statements appear in the literature that higher aluminum increases the brittleness, but probably the chief reason was the relative price of zinc and of aluminum when 4% alloys became firmly established. At that time, aluminum was three to four times the price •of zinc on a weight •basis. Recent prices, roughly equivalent per lb., make aluminum considerably cheaper than zinc on a volume basis and suggest that increased aluminum content would result in a decrease in the cost per piece due to the lower density of the alloy.Little information could be found in the literature and, therefore, it was decided to determine some physical properties of the higher aluminum zinc-base alloys made from high-purity zinc."

Jan 1, 1953

By G. M. Ross, J. A. Scott, C. A. Laamanen, H. Shang

"Indirect recovery and use of waste heat contained in smelter off-gas is proposed to expand regions available for year-round, on-site production of micro-algae–sourced biodiesel, a fuel that could be used in underground machinery. A dynamic model of an off-gas heat exchanger describes capture and distribution of heat into open, external, rectangular micro-algae ponds. Smelter off-gas contains sufficient energy to maintain large-scale micro-algae cultivation pond temperatures above 15°C, even with winter ambient temperatures below –15°C. Results highlight opportunities that could lie in tapping these heat resources to produce renewable biofuels on-site and sequester CO2 while leaving the industrial process unaffected.RÉSUMÉ On propose la récupération et l’utilisation indirectes de la chaleur résiduelle contenue dans les dégagements gazeux des fonderies pour développer les régions se prêtant à une production toute l’année durant et sur place de biodiesel à partir de micro-algues, carburant dont on pourrait se servir pour le matériel d’exploitation souterraine. Un modèle dynamique d’échangeur de chaleur contenue dans les dégagements gazeux décrit le captage et la distribution de la chaleur dans des bassins rectangulaires ouverts de micro-algues en extérieur. Les dégagements gazeux des fonderies contiennent suffisamment d’énergie pour maintenir les températures des grands bassins de culture de micro-algues au-delà de 15°C, même avec des températures ambiantes en hiver inférieures à –15°C. Ces résultats soulignent les possibilités que pourrait offrir l’exploitation de ces sources de chaleur pour la production de biocarburants renouvelables sur place et pour la séquestration de CO2 sans que cela n’ait d’incidence sur le procédé industriel.INTRODUCTIONMicro-algae that grow in water can efficiently convertsolar energy and carbon dioxide into biomass. This biomass can be up to 50% oils (lipids), which can be extracted and converted into biodiesel through transesterification (Demirbas, 2008). Compared to terrestrial plants that produce similar oils (e.g., jatropha, soybean, and rapeseed), micro-algae represent an order of magnitude increase in areal productivity, do not require arable land, and can be continuously harvested (Rawat, Ranjith Kumar, Mutanda, & Bux, 2013). The potential advantages through the production of biodiesel from micro-algae also include sequestration of carbon dioxide, reduced reliance on fossil fuels, and the co-production of other value-added bioproducts."

Jan 1, 2017

By Jas. G. Ross

Introduction Asbestos, a mineral known and used in ancient times, has become an article of commerce only during the life of the older asbestos miners in Quebec. The diversified uses of this adaptable substance are now numbered by the hundreds. Wherever insulation or resistance to heat may be required, asbestos, either by itself or mixed with some other material, may be employed to advantage. Regarded as a curiosity for centuries, it is now in such common use that it is familiar to all. The demand for long fibre for use in the manufacture of textiles and brake-lining, and for shorter fibre for making shingles, paper, and insulation materials, serves to support the industry of mining asbestos-bearing rock and milling the fibre from it in Canada, South Africa, Russia, Cyprus, and the United States. The commercial use of asbestos dates only from 1876, in which year large deposits were discovered in the Province of Quebec, Canada. Prior to that year a small amount of long fibre amphibole asbestos was produced in Italy. Occurrence In Canada In the Eastern Townships of Quebec, along the line of the Quebec Central railway, is an area of serpentine rock. It extends westerly into Vermont and easterly to Gaspe. A part of it, the section from Danville to East Broughton, contains areas in which occur deposits of commercial asbestos fibre of the chrysotile variety. Pits have been opened on some of these deposits at Danville, Coleraine, Black Lake, Thetford Mines, Robertson, and East Broughton. Thetford is distant 68 miles from Quebec city, East Broughton lies 25 miles to the northeast of Thetford, while Danville is 45 miles to the southwest of Thetford.

Jan 1, 1927

As a bubble travels through the pulp region of a flotation cell, it will collect the most hydrophobic particles of an intermediate particle size range, this being the primary source of true flotation selectivity. Despite its role on bubble-particle attachment, however, particle hydrophobicity is still missing a mathematical definition that can be used for plant simulation. In this paper, particle hydrophobicity is defined in terms of the induction time necessary for attachment and then linked to the mass of collector adsorbed per particle. This allows particle hydrophobicity to be written as a function of density of collector adsorption as well as particle size and mineralogy. The model is calibrated from the experimental measurement of the flotation rate constant. Liberation data from an industrial flotation rougher is used for model validation. It is demonstrated that the model can describe a broad experimental dataset by means of a minimal number of parameters. Main industrial application is in simulating the effect of the chemical environment upon plant metallurgical performance.

Jan 1, 2006