Search Documents

By B Abbasi

It is well known that most roof falls in coal mines typically occur at and around intersections. Room-and-pillar and longwall coal mining systems typically develop 3-way and 4-way intersections. This research develops an improved scientific understanding of stress distribution and associated instability behaviour around 3-way and 4-way coal mine intersections through 3-D numerical modelling and limited field observations. Numerical analyses were performed for an Illinois longwall coal mine to identify factors that influence intersection stability. The stability of immediate roof, floor strata, and coal ribs at and around intersections are considered with pre-mining regional horizontal stress. Non-linear failure analyses used the Hoek-Brown failure criterion for rock mass. Progressive failure zones in and around intersections were developed. For a typical 4-way intersection, pillar corners across the intersection fail first and lead to progressive failure of the immediate roof and floor layers. The mechanism of failure is similar for a 3-way intersection but the shape and extension of failed zones differ. For the 3-way intersection, the effect of off-set distance was analysed. It was found that minimum off-set distance of about 10 m (centre to centre distance between two 3-way intersections) was required to minimize interaction between two intersections. A simple instrumentation program monitor ground movements around intersections. These data were used to design the intersection geometry that is now being practiced by the mine. CITATION:Abbasi, B and Chugh, Y P, 2018. Instability analysis in three-way and four-way coal mine intersections, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 345–359 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By K Johnson, G Morrison, N Lisowiec

The Mount Wright gold deposit is located near the town of Ravenswood, ~90 km south of Townsville, in north Queensland. The deposit has been mined by underground methods since 2006. It produced approximately 138 koz Au in the 2011 - 2012 financial year and has a total endowment of approximately 1 Moz Au. To facilitate near mine exploration, a re-logging campaign of 600+ diamond and RC drill holes was recently conducted, resulting in a revised three-dimensional (3D) geological model and improved understanding of the ore controls and the mineralised system. The deposit is within a Permo-Carboniferous breccia complex approximately 350 m diameter and more than 1200 m deep. It consists of early peripheral granite-rich breccia, polymict breccia, a rhyolite spine and a late tuffisite (fine-grained milled breccia) pipe. The rhyolite spine is approximately 60 m + 250 m + at least 1200 m deep and is zoned with massive, flow-banded and breccia phases that are in part gradational with the other breccias. There is extensive sericitic alteration centred on the tuffisite and rhyolite units and fading out into the shallower and peripheral polymict and granite-rich breccias. There is also a broad pattern of metal zoning with elevated Pb-Zn ¦ Ag in the upper 400 m, Au-Cu-Bi below 400 m fading out below ~850 m, and a poorly defined deep Mo-W-Te-Sb anomaly. The majority of the Au ore is between 400 and 850 m below the surface in the rhyolite spine. Below this, Au mineralisation is less coherent, and more localised in the margins of the rhyolite and in the adjacent tuffisite. The developing model is that the ore is not confined to or necessarily directly genetically related to the rhyolite spine, but is driven by other phases of intrusion that also generated the tuffisite pipe. This model is being used to generate additional drill targets away from the present mine development.CITATION:Johnson, K, Morrison, G and Lisowiec, N, 2013. Advancing near-mine exploration with an updated geological model for the Mount Wright gold deposit, Queensland, in Proceedings World Gold 2013 , pp 469-478 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By M Ind, B Usher

Environmental regulators are increasingly adopting risk-based approaches to protect aquatic ecosystems. The Australian and New Zealand Environment and Conservation Council (ANZECC) and the Agriculture and Resource Management Council of Australia and New Zealand (ARMCANZ) (2000) introduced a risk-based approach to water quality guidelines that use decision frameworks to adapt water quality guidelines to local environmental conditions. Environmental quality objectives are no longer a simple ‘pass or fail’ number such as restricting total suspended solids (TSS) concentration to a specified limit for a particular rainfall event. This approach ignores spatial and temporal variability and the complexity of aquatic ecosystems. The risk-based approach establishes levels where adverse effects may occur. If these objectives are not met, further risk-based investigation is undertaken to assess the potential impact to the ecosystem. Klohn Crippen Berger (KCB) developed a dynamic simulation to predict the variability of sediment discharges, which is applicable for risk-based impact assessment of aquatic ecosystems. The application of the methodology over the life of a mine site is illustrated using a proposed South Pacific mine.The site location is in extremely rugged terrain with a high annual rainfall of approximately 4.7 m. There were two major sediment ponds proposed to reduce sediment discharges. A sediment and hydrology model was developed in Goldsim to provide daily estimates of run-off flows and sediment concentrations. A modified algorithm based on the Australian water balance model was created and incorporated into the Goldsim model and calibrated using recorded field data.The sediment module was developed based on a Revised Universal Soil Loss Equation (RUSLE) assessment, an annual prediction of soil loss over a catchment. A land-use type erosion vector was developed for different land-use types and for each of the subcatchments, a subcatchment erodibility vector was calculated. This vector and the daily rainfall erosivity factor were used to estimate the daily soil loss. The estimated soil loss and the modelled run-off yielded predictions of daily sediment concentrations. Finally, a sediment settling module was used to predict the daily efficiency of the sediment ponds and hence discharged sediment concentrations.The results of this modelling form the first part of a quantitative risk-based assessment into suspended solids impacts. The second part is the assessment of the effects of these predicted TSS concentrations on aquatic ecology. As part of the feedback-loop required in a risk management framework, if the environmental quality objectives are not met then further management decisions and actions may be required to reduce the risks presented by suspended solids. This may include modifications to: the mine-development plan; construction techniques and scheduling; processing techniques; rehabilitation strategies; or hard-engineering solutions such as sediment basins or flocculation.The Goldsim water-balance model provides a quick and efficient method of testing potential remedial actions on predicted sediment loads and concentrations. In combination with a cost-benefit assessment, options for reducing sediment releases from the mine site can be effectively and quantitatively compared thereby providing mine operators with a basis for decision-making. Regulators can also be satisfied that potential impacts to aquatic ecology have been comprehensively assessed and the necessary management decisions have been initiated to limit risk to the environment.CITATION:Ind, M and Usher, B, ?2014. A dynamic sediment simulation to predict the variability of suspended solids concentrations over life-of-mine for application to a risk-based environmental assessment, in Proceedings Life-of-Mine 2014 , pp 191–204 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By X Tian, J Forster, A Olmsted, E R. Bobicki, M Goldbaum, D Boucher, C A. Pickles

As the global demand for metal values expands, it becomes increasingly important to create more sustainable mining operations. Consequently, considerable research and technology development is required to produce processes which are both more energy efficient and have a minimal environmental impact. One potential technology is the utilisation of microwave pre-treatment to reduce the energy requirements in comminution. Microwaves can preferentially heat the valuable mineral phases in an ore and the resulting differential thermal expansion leads to the formation of microfractures along the grain boundaries. As a result of the preferential heating, ore competency is reduced, mineral liberation is enhanced, a coarser grind size can be employed, and plant throughput can be increased. Furthermore, microwave pre-treatment can be combined with advanced ore sorting, to decrease the quantity of gangue material processed downstream and hence reduce tailings production. Previous studies on the microwave treatment of ores over the last 30 years have mainly been limited to low power bench-scale studies and there is a paucity of information on pilot and/or commercial scale studies. In the present research, the microwave heating behaviours of over 40 ores have been studied at the bench-scale. These results were used to generate a database, from which a unique classification system was developed. This system was used to rank the amenability of any given ore for microwave pre-treatment. This knowledge can be employed to predict the performance of the ores in the high-power pilot scale tests and thus can be used as a pre-screening tool. The effects of high-power microwave pre-treatment on grindability and liberation were reported. Additionally, the ore sorting potential was evaluated using a combination of X-ray transmission (XRT) and microwave infrared (MW/IR).

Aug 24, 2022

By J W. Lee, E Baafi, N Aziz

Ground subsidence due to mining is a common dilemma confronting the underground coal mining industry. The effects of underground longwall mining on river valleys have come under scrutiny, especially when mining is located underneath catchment areas. As public awareness of mining impacts on the environment increases, there is the need to develop damage mitigation strategies. Results of numerical modelling show that river valley response to underground longwall mining can be simulated and evaluated.

Jan 1, 2005

By Nava-Vasquez E, Torres-Torres J, Mendez-Nonell J

The ZA-27 zinc base alloy was poured into cylindrical moulds and solidified under different conditions ie normal freezing and unidirectional freezing. In addition a cylindrical ingot with rheocast material was obtained by stopping the stirring action and, at a specific solid fraction, gravity casting it into a graphite mould. It was observed that the material obtained under normal freezing conditions is likely to present both segregation and inverted pipe. In contrast, the unidirectional solidified and the rheocast cylinders showed the absence of inverted pipe. The segregation pattern was quite irregular in the rheocast ingot while such segregation was more uniform in the unidirectional solidified cylinder. By virtue of these observations, the inverted pipe formation may be ascribed to the interdendritic flow, while the irregular segregation pattern in the rheocast ingot may be attributed to an irregular distribution of the liquid and solid fraction along such a cylinder.

Jan 1, 1993

By J Zhou

Gold in sulfide ores is associated predominantly with sulfide minerals and occurs as both microscopic and submicroscopic particles. In non-refractory sulfide ores, gold occurs mainly as coarse- and medium-grained particles. Minute inclusions and submicroscopic gold usually account for a minor portion. In contrast, gold in refractory sulfide ores occurs mainly as minute particles and submicroscopic gold, and microscopic gold usually accounts for an insignificant portion. In gold ores containing carbonaceous material, the preg-robbing nature of carbonaceous material may impose challenges on gold extraction and cause gold losses. To extract gold from refractory sulfide ores, the ore needs to be finely ground and preoxidation is often required. Sulfide host minerals must first be oxidised to create a porous structure through which the cyanide leach solution can penetrate to reach the colloidal gold particles. The oxidation is traditionally achieved by roasting, autoclaving or bacterial oxidation. In carbonaceous sulfide ores exhibiting a preg-robbing nature, the carbonaceous material needs to be treated by roasting, autoclaving or other means to minimise the preg-robbing effect. As a predictive and troubleshooting tool, the gold deportment study plays an important role in gold metallurgy. It determines the deportment of gold in an ore or mill product and identifies the mineralogical issues that may affect or may have affected gold extraction. The information acquired from a gold deportment study can be used to assist in process selection, flow sheet development, recovery improvement and reagent optimisation.CITATION:Zhou, J, 2013. Deportment of gold in sulfide ores and implications for gold extraction, in Proceedings World Gold 2013 , pp 433-442 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By G Morgan, C Kemp

In December 2010, a trial of borehole radar technology was conducted to test the usefulness of the technique in better refining the position and geometry of narrow vein orebodies away from the primary data sources of drilling and mapping of development excavations. This paper summarises the reasons why the technique was applied, describes the testing methods selected and summarises the outcomes of the trial.Poor reconciliations of recovered metal from a section of an orebody at Jundee mine site, Western Australia, led to an investigation that identified insufficient understanding of the geometry of a narrow vein orebody as a potential cause. This orebody was situated between mapped development excavations and away from surrounding drill holes. Borehole radar was identified as a possible technique that could supply information on vein location and continuity away from other data sources allowing more accurate orebody modelling and subsequent stope optimisation.A borehole radar instrument (10 - 100 MHz frequency) was inserted into pairs of purpose-drilled boreholes on either side of relatively well-constrained mineralisation and the radar reflection data was collected. This process was repeated in five locations across the mine to represent the most common geological settings, lithologies and orebody varieties encountered at Jundee to determine the suitability of applying the technique in each of these settings. Collected, processed and interpreted radar data was compared to other geology data collected independently for verification and interpretation.Conclusions drawn from the analysis were that the technique could effectively determine the following features of the mineralised veins in the majority of test environments: geometry of veins, magnitude of offsets where structures intersect and orientations of planar structures with short strike length. The technique was very useful in selecting the appropriate structural interpretation where available data could lead to multiple, equally likely, interpretations.CITATION:Kemp, C and Morgan, G, 2012. Using borehole radar to refine orebody interpretations in a narrow vein gold deposit, in Proceedings Narrow Vein Mining 2012 , pp 121-130 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By D Preedy, J K. Claflin, S R. J La Brooy

This paper summarises the lessons learned during a recent carbon reactivation kiln upgrade project at the Sukari Gold Mine in Egypt. The kiln is being replaced to ensure that the plant achieves full value from the current throughput expansion from 5 to 10 Mt/a.The suitability of the original engineering design criteria for kiln selection and the adequacy of the original kiln are reviewed in the light of the carbon chemistry, operating experience and a site inspection of the kiln. Particular aspects of the reactivation facility are discussed including: predrying, preheating, feeding, gas seals, kiln heat transfer, steam injection, counter-current sweep gas flow, carbon cooling, fines minimisation and removal.Design criteria for a carbon predryer, reactivation kiln and cooler combination for carbon heavily fouled by high molecular weight frothers and collectors are discussed and the abridged Ausenco datasheet for the combination is presented.Responses to a request for a budget price sent to most of the worldÆs suppliers of carbon regeneration kilns are summarised.CITATION:Claflin, J K, La Brooy, S R J and Preedy, D, 2013. Ausenco carbon reactivation design criteria, in Proceedings World Gold 2013 , pp 401-410 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By C Zhang, I Canbulat, G Fan, D Zhang, C Wang

A clear understanding of the intensity of coal and rock burst is the basis for future research on burst mechanism and control. There has been a wide variety in the description of coal and rock burst damage at different countries using multi-methods, which makes the common understanding even more challenging. Therefore, this paper presents a broad review on the quantifications of intensity of coal and rock burst and seismic risk around the world, considering critical factors including seismic energy, magnitude, peak particle velocity and ejection velocity. It is found that the seismic energy of coal and rock burst can widely range from 0.002 MJ to 60000 MJ, with equivalent Richter magnitude from -1 to 4. The daily seismic energies can be used for seismic risk potential assessment, with energy levels from 0.1 KJ to 10 MJ, which is much lower than the burst sources. The magnitude of the seismic events can be also estimated based on the weight of damaged coal mass and human senses of vibration and sound. For the seismic intensity represented by peak particle velocity (ppv), it keeps constant within fault radius and attenuates with a speed of 1/r4 and 1/r in near and far field respectively, thus it is possible for a small seismic event to induce considerable ppv causing severe damage if the epicentral distance is small enough. There has not been a strong correlation between the ejection velocity and ppv, as seismic energy is only one of the energy sources that contribute to the kinetic energy of burst damage. CITATION:Wang, C, Zhang, C, Canbulat, I, Zhang, D and Fan, G, 2018. Intensity quantification of coal and rock burst risk – a review, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 223–233 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M Runkel, J Hammerschmidt, A Holmstr÷m, A Charitos, J Gnntner

"Roasting of sulfide concentrates and refractory ores is an important process step in the production of metals and chemicals. Sulfides of iron, zinc, copper and other metals are oxidised with air between 600 and 1000¦C into metal oxides or sulfates and gaseous sulfur dioxide. Roasting of gold concentrates and ores is a typical processing step used to produce a porous calcine suitable for cyanide leaching. During roasting, elements posing problems are removed through: oxidation (carbon, sulfur, arsenic and antimony) or volatilisation (mercury, chlorides and tellurides, as well as arsenic and antimony).This paper focuses on the environmental aspect of roasting using fluidised bed technology. The approach is to show that roasting is an attractive solution for refractory ore pretreatment since, on the one hand, it is an efficient technique yielding high gold recovery rates, while on the other it is able to comply with current stringent international environmental regulations. In that respect, roasting is compared to alternative processes, ie pressure oxidation (POX), bio-oxidation (BIOX) and ultra-fine grinding (UFG). Roaster high gold recovery rates are ensured through roasting-leaching test work, which allows the derivation of respective roasting parameters that are easily achieved in an industrial plant. On the other hand, key elements of the roasting process are analysed, which make it an efficient and sustainable technology, ie the possibility for energy recovery, the removal of off-gas impurities during the different gas cleaning steps (handling of arsenic, mercury emissions and further hazardous dust and gas emissions) and the treatment of the SO2-gas in order to produce sulfuric acid, and finally the treatment of the effluent produced. The processÆs environmental aspects are summarised by listing roasting emission values that comply with international regulations.CITATION:Charitos, A, Runkel, M, Gnntner, J, Holmstr÷m, A and Hammerschmidt, J, 2013. Roasting - a study on environmental aspects, off-gas, effluents and residue treatment, in Proceedings World Gold 2013, pp 509-518 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 26, 2013

By I Sucholutsky, D M. First, D Mogilny, F Yusufali

Machine learning is creating value in all facets of the mining industry, from exploration to production. The authors provide an accessible, high-level introduction to artificial intelligence (AI), machine learning (ML), and deep learning (DL); the latter being widely recognised as one of the most powerful forms of ML. In particular, the authors will introduce deep learning models known as convolutional neural networks (CNNs), how they are applied, and the economic considerations necessary for determining when DL may be the right solution to de-risking complex block modelling problems. The authors present preliminary results from the mineral resource modelling study of the Jundee orogenic gold deposit, Yandal belt/gold province, Western Australia. The primary goal was to identify the direction and location of the narrow gold veins more accurately and demonstrate how non-linearly correlated elements are used as direct inputs to the resource model to assist with the target element’s grade prediction. This demonstrates that: (1) existing techniques for finding correlations between assayed elements do not adequately reflect the complex geology of the asset, (2) nonlinear correlations that are difficult to model as simple mathematical functions are representative of geological patterns in a deposit, and (3) non-linearly correlated assayed data, fed as inputs, increase the performance of the resource model as reconciled through blind tests. To conclude, the authors hypothesise that the patterns represented by the DL block models may be revealing the results of overprinting geological processes that generated mineral deposits. For example, the primary hydrothermal processes that deposited metals created depositional patterns that become particularly complex as a result of being overprinted, in part or in whole, by secondary physicochemical processes. This may explain why non-linear geochemical relationships have the capacity to generate more accurate block models of mineral deposits.

May 24, 2023

By S Bailey

In-field sampling programs generally take time, equating to money, and unless you have an onsite laboratory, you have the issue of having to wait long periods for your data. Until recently, field portable X-ray fl uorescence (FPXRF) analysers, which can help provide instant indicative results, were not able to detect penalty elements, such as Al and Si, or do so reliably enough to act upon.The purpose then of this field test then was to show that the latest FPXRF devices are capable of producing reliable readings on field samples of variable grain size, in particular for Al and Si, such that the readings still correlate well with the assay for those samples and thus be reliable for an iron ore grade control application.We tested RC chip samples on-site in the Pilbara, Western Australia, with the Niton, analysing for a range of elements including Fe, Mn, Al and Si and then compared the results for those elements against assay data for the same. A strong correlation would tell us that the FPXRF results were reliable. Furthermore, to show the effect of simple sample preparation, we also analysed pulps of the same samples in the same way.The correlations were good for the all of the four elements of interest for the RC chip samples (R2 values between 0.82 and 0.9), and excellent for the pulps (R2 values between 0.89 and 0.998).The results also showed a direct correlation between sample preparation and improved quality of results with the FPXRF.The data showed allowed for two conclusions:1. the FPXRF can produce data from unprepared RC chips for Al and Si that, when compared with assay, is reliable for a fi eld application in drilling and grade control; and2. the greatest limitation to data quality is sample preparation.

Jul 11, 2011

By D Bruggemann, F Sereshki

There has been an ongoing research on coal and gas outburst for the past two decades at the School of Civil, Mining and Environmental Engineering, University of Wollongong. Research study began with a humble beginning, initially conducting basic laboratory studies on the coal and gas properties, progressing into the determination of gas content of coal by sorption technique and the effect of gas pressures on coal strength. The present laboratory facilities and research interests are extended to include the study of coal permeability and shrinkage properties and their effect of gas drainage characteristics with respect to gas type, and pressures. All the changes are examined with respect to changing in-site geological conditions of the coal deposit investigated. The aim is to provide a long-term support to industry in establishing a data bank for Australian coal deposit characteristics and properties.

Jan 1, 2005

By F Saloojee, F K. Crundwell

Refractory ores need to be pretreated prior to cyanide leaching for acceptable gold recovery. Pressure oxidation is one method of rendering the ores more suitable for cyanidation. The focus of this work is optimisation of autoclave configuration for pressure oxidation. An autoclave for the pressure oxidation of a feed containing pyrite and arsenopyrite was modelled, using the population balance framework. The autoclave model takes into account feed particle size, reaction kinetics and retention time. Mass balance calculations were incorporated into Cycad Process« software. This allowed for the investigation of different circuit configurations. The base case model consists of a single autoclave. The feed was then doubled and additional autoclaves were added to provide the same residence time as the base case. Four different configurations for the additional equipment were simulated. These were parallel, series, series with inter-stage thickening and parallel-series circuits. The options are compared in terms of extraction and productivity. The parallel circuit behaves similarly to the base case. The series and series-parallel circuits have higher recoveries and productivities than the base case. The series circuit with inter-stage thickening provides the highest extraction and productivity. This is because the thickening reduces the slurry volume and increases the residence time of the solids in the downstream autoclave.CITATION:Saloojee, F and Crundwell, F K, 2013. Optimisation of circuits for gold pressure oxidation, in Proceedings World Gold 2013 , pp 181-188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By P Klaric

Drive stability is critical in block/panel cave mining. The production levels of these mines are required to remain operational for the entire life-of-mine which can be in excess of 30 years. It is therefore necessary to produce high-quality drives to ensure sustainable mine productivity. In order to improve the quality of drives and pillars, this gold mine instigated a project to optimise their development blasting. The initial aim was to reduce the level of overbreak in development mining, which was averaging approximately 18 per cent. The benefits of controlling overbreak not only included an increase in the integrity of the drives but also a decrease in load and haul and ground support costs. Through focusing on the optimal blasting of the perimeter holes, overbreak was reduced to 4.5 per cent. The project’s focus then moved to drill and charge designs for development faces. In optimising these designs, it was anticipated that improvements in the development mining cycle would be achievable.CITATION:Klaric, P, 2015. Improving drive stability through efficient development blasting design and practices, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 327–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J Battista, J Grace, I Brunton

The need to better understand and develop strategies to improve instantaneous shovel productivity at the Cadia Hill Open Pit Mine (CHM) instigated the development of the æShot to ShovelÆ project. This project has involved the implementation of a drill and blast (D&B) information management system to capture current and future experience. Equally important has been the manual monitoring of shovel productivity and direct use and analysis of high precision GPS and productivity data logged by ModularÆs Dispatch System. The analysis of this type of data was facilitated with the application of GIS based software (ie MapInfo). This has shown to be a powerful medium to display, interpret and assess this type of spatial information on a blast-by-blast basis. Cadia HillÆs well-defined D&B processes supplemented with the application of the above systems are providing a unique capability to assess and better understand the impact of both muckpile conditions and operator proficiency on instantaneous loading productivity. This is facilitating the definition of appropriate optimisation strategies in both drilling and blasting and operator proficiency training. This paper gives a summary of the work conducted in the æShot to ShovelÆ project, describes the engineering tools being implemented and discusses preliminary findings and their practical implications.

Jan 1, 2004

By M Lak, R Amiri, A Haratian, M Asghari, S Haji

Dry magnet separators are used to upgrade and beneficiate a wide variety of minerals such as hematite and magnetite materials. In recent years advances in dry magnetic separators have improved their performance. Fine particle separation is one of the main areas which still remain weak. This paper will present a new design of fine particle drum separators which used for particle size less than 3 mm. A big problem in processing of iron ore is the grade and recovery of mineral values in the fines fraction. The new design high efficiency drum separator is developed to handle fine feeds. In this drum separators both of the drum shell and magnetic yoke rotate in opposite direction. the results showed that when the material feed size was = 1298 μm, drum shell speed was 42.5 rev/min, magnetic yoke speed was 100 rev/min and the maximum intensity of magnetic field was at = 30° the feed grade increased from 50.87 to 65.67 in concentrate box, increase to 60.45 in middle box and tail grade was 24.44. The total achieved recovery for both concentrate and middle box was 81.89 per cent.

Nov 8, 2021

By K G. Harding, A Osman, A du Toit, F K. Crundwell, C M. Sheridan

"Most mineral processing plants have high water requirements for their operational activities. These plants often function in an environment where water is becoming increasingly scarce. An increase in population will result in an increased demand for water; potentially beyond the limits of supply and hence increased competition for the resource. In South Africa, Gauteng and the North West Province are likely to be first to experience a shortage of potable water.In order to avoid a water crisis, efforts must be made to ensure the effective management of water resources and the minimisation of wastage. Hydrometallurgical plants have a responsibility to society and the environment to operate in a sustainable manner - reducing their water requirements will certainly assist towards developing a sustainable footprint.This project improved site water management by: surveying the potable water and storm water systems with a view to assessing the current water accountability and determining methods to improve accountability determining the monthly and yearly water balance for the site and presenting it in the form of a water balance sheet drawing up an input-output and operational model in accordance with the Minerals Council of AustraliaÆs æWater Accounting Framework for the Minerals IndustryÆ calculating the water footprints of the refinery identifying ways in which water savings could be achieved recommending management systems for water usage monitoring.This work was conducted in South Africa. The value of this work lies in that it established the current baseline and assisted in developing management systems that can reduce water usage sustainably.CITATION:Osman, A, Crundwell, F K, Harding, K G, Sheridan, C M and du Toit, A, 2013. Water accountability and efficiency at a base metals refinery, in Proceedings Water in Mining 2013, pp 277-286 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

Improved roof control in high deformation tailgate environments has been achieved over the last decade through development of stiffer and increased capacity standing support products. æThe CanÆ is one such development, being a steel cylinder containing a weak cementitious fill, designed to essentially fold in upon itself whilst maintaining strength. A laboratory study to better define the relative load contributions of the steel cylinder and fill, the confining interaction between these components and most importantly, the potential impact of varying the steel and/or fill properties is described. This would enable the support engineer to ædial-upÆ the desired strength and stiffness properties and optimise the standing support design with respect to load capacity, stiffness, weight (handling) and cost. Design curves to optimise strength based on steel casing thickness, fill strength (confined and unconfined) and æCanÆ geometry were established. Scaled-down (one-third) samples were used in the test program and found to adequately reflect the loading behaviour of full-scale versions, thereby providing significantly greater scope for further product development at less expense compared with testing full-scale products.

Jan 1, 2005