Search Documents

By Muller GP, van Deventer JSJ

A mineralogical analysis has shown that in the Hartebeesfontein ore studied, uranium is associated mainly with uraninite, sulphides such as pyrite and to a lesser degree carbonaceous material such as thucolite. Little could be learned from the literature regarding the mechanism of flotation of these uranium-bearing minerals. A wide variety of reagents were used so that conditions enhancing the flotation of either the sulphides, carbonaceous material, oxides like uraninite, or combinations thereof, were created. As could be expected, the xanthate based floats gave-better selective recovery of sulphides than oleic acid. A substantial fraction of the uranium is associated with pyrite, so that addition of oleic acid to a xanthate float did not enhance the recovery or grade of uranium. After a pre-leach with sulphuric acid in which the pH and Eh were controlled so as to destroy the uraninite, higher uranium recoveries were obtained for the combined float (xanthate, DTP and oleic) and the DTP float. This was most evident when iron was added before flotation. Roasting, which destroyed the sulphides and thucolite, caused a significant decrease in uranium recoveries. The uranium liberated in this way was obviously not flotable in the same way as the uranium liberated from uraninite. A small amount of iron (2 kg/t) added before milling resulted in slightly higher grades and recoveries of sulphur for xanthate based floats. Higher iron additions had a detrimental effect on sulphur recoveries. Even in the case of oleic acid the addition of small amounts of iron had a positive effect on the recovery of sulphur and uranium.

Jan 1, 1993

Most types of nuclear power reactors use uranium dioxide fuel. Power reactors using natural uranium dioxide'fuel are of special interest to countries such as Australia that have their own uranium supplies. A wide range of uranium dioxide powders can be fabricated and the ideal one flows readily, presses without the need for binders or lubricants, sinters to the required density and gives low reject rates at all fabrication stages. Sinterable uranium dioxide is usually produced via the ammonium diuranate route. The A.A.E.C. is aiming to demonstrate production of nuclear grade uranium dioxide from Australian concentrates, improving technology where possible. Details are given of the dissolution, solvent extraction, precipitation, filtration, drying, and calcination-reduction steps. Solvent extraction from sulphate media is also under study with a view to developing a process to produce a nuclear grade product at the mine treatment plant site,

Jan 1, 1969

By Brumley J

The development of the SECV brown coal open cut at Loy Yang will require depressurisation of aquifers both within and below the coal seam sequence in order to maintain open cut stability. Prediction of future open cut dewatering requirements at Loy Yang Open Cut and evaluation of the regional consequences of dewatering has required development of a detailed hydrogeological model of the Loy Yang area. The complex stratigraphy of the coal seam and aquifer/aquitard sequences at Loy Yang have been analysed and integrated with the hydrogeological concepts developed from regional groundwater studies to formulate a realistic hydrogeological model as a basis for finite-element flow modelling.

Jan 1, 1988

The intention of this paper is to examine the practical and technical aspects associated with the measurement of blasting related phenomena. The emphasis is directed towards the acquisition of quantitative data rather than its theoretical interpretation. The application of advanced technologies will require that many more people involved with blasting become familiar with this topic. Against the many other disciplines where measurement may be beneficial, blasting is peculiar on several counts. 1) It must almost always be carried out in the field, and very often in a production environment. 2) Much consideration must be given for the safety of personnel and equipment. 3) The process is dynamic and seldom repeatable. Because the blast process is so dynamic there is little opportunity for direct examination. For this reason measurements are almost universally made using electronic techniques. In this way the event can be captured faithfully as it occurs and later examined in detail, after the fact. It is obvious that some familiarity with these electronic techniques is a necessary ingredient for successful blast monitoring.

Jan 1, 1990

By Manca PP, Rossi G, Lipari D, Knissel W, Massacci G, Licheri P, Fioravanti E, Helms W, Lai S

Mining of the massive complex sulphides orebodies of Campo Pisano and San Benedetto (Southern Sardinia, Italy), dates back to before Christ, though their exploitation with modern technology was only resumed in the middle of the last century. The increasingly adverse economic conditions and the weakness of both country rock and mineralization were concurrent in forcing the Company's management to develop suitable high-productivity stoping methods. In the framework of a project fi- nanced in part by the Commission of the European Coranunities, and carried out in cooperation with the Universities of Cagliari (Italy) and Clausthal (Germany), a cemented backfill stoping method was developed. The concrete mix preparation and placement facil- ities, study of the cement mixes and endeavaa-s to optimize the methods are described. The monitoring system for measuring stress evolution within the emplaced backfill is illustrated together with the successful replacement of part of the Portland cement

Jan 1, 1992

By Dendyuk TV

The possible use of combined (flotation/magnetic separation and magnetic separation/flotation) technologies involving the new flotation reagent systems for upgrading the iron ore concentrates, low grade manganese products and beneficiation of graphite-bearing dusts from integrated iron-and-steel works has been shown. It has been found that the absence of magnetic flocculation phenomenon worsens the reverse cationic flotation of oxidised iron ore concentrates and direct flotation of low-grade manganese products which require the use of modifiers possessing the flocculating properties. The synergetic mixtures of polymers have been proposed to be used as modifiers, ie polyacrylamide (PAA) with carboxymethyl cellulose (CMC) and polyacrylamide with industrial lignosulphonates (LST)

Jan 1, 1993

Conventional narrow vein mining, utilising hand held methods, is expensive and requires specialised miners who are becoming a rarity. Hand held mining techniques (shrinkage stoping, leading stoping and cut and fill) have the advantage that they can be selective. The methods allow continued sampling of the face, control of hanging wall conditions and are adaptable to changes in strike and dip. On the other hand, more productive longhole stoping methods can allow excessive dilution due to drill hole deviations and changes in orebody dip and can be subject to unexpected hanging wall or footwall failures. Development of small scale equipment (as narrow as 0.8m wide) used for drilling or bogging very smallaccess drives has been ongoing over the past decade. In this paper, types of equipment are examined and compared, particularly with respect to their produc- tivity, size, and working environment. The introduction of electric hydraulic equipment has provided a better working environment with reduced noise, exhaust fumes and heat. The concept of the "hydraulic cherry picker" may have application in mining steeply dipping orebodies. The system requires orebodies to be reasonably consistent in dip over 15 metre sub-level intervals. The system involves the basic concept and skills of machine and airleg mining, combined with the safety and productivity of a mechanized work platform. The platform or basket is stabilized between the hanging wall and foot- wall by hydraulic rams and is extended by a tilting hydraulic boom mounted to a small prime mover or trailer. Design concepts (including remote controlled charging of explosives, adaptation to the boom for rock cutting and the overall electric hydraulic mining concept) are put forward in the paper as a view as to how narrow vein mines will be mined in the future.

Jan 1, 1987

The paper covers the history and develop- ment of electrical and diesel-powered hydrau- lic percussion rock drills. It examines main design aspects and problems encountered in pro- ducing an efficient and reliable machine to fully cover the nominal hole sizes required for underground development, production drill- ing and for general quarry work. The main design features and advantages of a hydraulic rock drill are relatively low input power requirement to energy per blow (this being achieved by the use of an electric or diesel- powered hydraulic system) and a specially con- structed piston using a powered damper cylinder to absorb the recoil forces from the drill steel and reduce stresses on the drill, feed and hydraulic boom. A further important design feature is the anti-jamming device which controls the drill both during manual and automatic operation. This anti-jam device works on feed and rotation press and prevents the drill bit becoming jammed in broken or soft ground. These features and many other mechanical and environmental benefits are highlighted when comparing hydraulic percussion rock drills with current pneumatic machines. The hydraulic rock drill gives an overall high penetration and production rate, with an added bonus for ergonomy and environmental conditions such as lower noise level, no fogging from air and oil exhaust (which naturally gives better air for breathing),plus improved vision when in under- ground situations. Hydraulic rock drills and systems have been fully tested in many mines, quarries and contract sites during the past years. They h6! been improved and modified and are now provi~ to be very reliable and economical piece drilling equipment whò in mines and quarries.

Jan 1, 1978

By Egan J. R

Changes have recently been applied to the Sullivan Concentrator lead and zinc circuits to treat fine-grained ores which make-up the majority of ore reserves in the mine. Pilot plant testwork conducted in 1990 - 91 indicated that concentrate grades would be substantially improved by reducing the particle size (Pao) of the lead from 38 to 15 ¦m and the zinc from 45 to 24 ¦m. Circuit revisions involved installation of major new equipment including: two 600-kilowatt Vertimills for regrinding, a four metre diametre column flotation cell and a four metre diameter hyperbaric pressure filter for dewatering. Duties of the existing regrind mills were Reassigned.

Jan 1, 1993

By Cox SJD, Kramadibrata S

One of the major causes of accidents and loss of production in underground mines is falls of ground.As mines go deeper, higher stresses are encountered and strain energy stored in the rocks is more likely to be released dynamically. This results in bumping in the rock mass around a stope or development face. Such noises and increasingly difficult ground conditions are obviously a warning of more serious problems ahead. The activity is collectively referred to as rock bursting.In Australia the mining of metalliferous deposits is taking place at increasing depths at Mt Isa, Broken Hill and the Eastern Goldfields and ground control problems with rock bursts has already been experienced at all three sites.

Jan 1, 1990

By M D. Goodz, Wright R. F

This paper highlights the importance of accurate observational technical reports compiled by Mining Geologists and Engineers. Before uncovering the original reports in July 1992, all previous investigations discounted returning to old mining areas on the belief that all operations were suspended because they were 'unpayable'. However, the detail of the original reports removed any doubt of the economic value of retrieving remnant ore.The important feature was that the description of 'unpayable' by GMA could be equated to 11.6 - 35 g/t over the history of the mine. On the basis of these reports the Morning Star mine has been re-opened.

Jan 1, 1993

By Bearman R. A

The majority of published material regarding the operation of crushing machinery is concerned with simulation of performance rather than design of equipment. The reason underlying the bias in published material relates to why research is carried out and who undertakes the research. Two distinct types of research can be identified: 1. Internal research by crusher manufacturers - generally related to mechanical design, value engineering and to the commercial realities attached to sales demands. Any work on basic crusher geometry or rock/machine interaction is of a sensitive nature and rarely enters the public domain. 2. Academic research - mostly confined to modelling of crusher performance and simulation. This is not because of any bias, but crusher design requires access to manufacturers data or at least an in-depth understanding of crusher design, which is rarely available. The crushing of rock is a complicated problem. It involves three aspects; the machine geometry, the material composition (type of rock/feed size distribution) and the machine/rock interaction. The machine geometry is often ignored in empirical mineral processing simulations, while the response of different feed materials is only nominally addressed in machine specifications provided by manufacturers. The manner by which the machine produces a stress field and causes different types of breakage for different rocks (or the machine/rock interaction) is sadly neglected by both groups. All three aspects must be considered collectively to successfully understand and model the entire crushing process. 1. Centre for Mining Technology and Equipment, Julius Kruttschnitt Mineral Research Centre, University of Queensland, Isles Road, Indooroopilly 4068 Qld. The importance of crushing is often underestimated. In mining and mineral processing the invisibility of the crushing process is understandable as it merely provides a coarse reduction stage prior to the intricacies of mineral extraction. However in the quarrying industry crushing and screening basically provide the finished product. A brief overview of the quarrying industry shows the importance of crushing. Figure 1 gives production figures for most of the western European countries, Australia and the USA.

Jan 1, 1995

The research, development and testing of a Blast Control Plug (U.S. Pat. #4,754,705) funded by the U.S. Department of Energy is described. The plug's function is to improve blasting efficiency through the enhancement of stemming effectiveness and thereby reduce drilling and blasting costs. The plug comprises a solid unit placed in the blast hole within the stemming column above the explosive. It is designed for use with back filled drill cuttings or any other suitable material The research and development program comprised the testing of the plug in small diameter holes in competent rock for both bench and crater blasting configurations and full scale field trials in multiple hole and row blasts using blast holes of from 76 to 387 mm in diameter. Test measurements included stemming displacement and velocity, face movement and extent, peak air over pressure and ground surface peak particle velocity. Data acquisition equipment included a Spin Physics SP2000 high speed video motion analysis system, and acoustic and seismic monitoring units. Substantial reductions in stemming ejection velocity or ejection elimination were achieved whilst reducing stemming length by up to 35% over conventional practice. Peak air blast pressures were also reduced by between 8 and 25 dB. A strong inverse relationship between rock face movement and stemming ejection velocity was found. The implications of the importance of stemming effectiveness in blasting and computer blast simulation is also addressed.

Jan 1, 1990

By Williams P

The assumptions made in conventional (Terzaghi) consolidation theory are not met in a tailings deposit. Finite or large strain consolidation theory must be employed. The paper describes such a consolidation model and its application to the design of tailings impoundments, water management systems, and long term rehabilitation.

Jan 1, 1990

By Theophili CN, Kapenis AP

Seismic tomographic imaging has been applied to determine the blast induced damage zones in bauxite pillars in underground mining. At the retreating stage, when pillar dimensions are reduced from 8 x 8 m to approximately 5 x 5 m, the' seismic tomographies reveal, through measurements of the P-wave velocities which is a measure of the degree of fracturation of the pillar rock mass, the presence of three zones within each pillar. In the external zone, where velocities recorded are below 750 m/s. extensive pillar damage occurs which is attributed to both the growth and coalescence of pre-existing cracks and even the creation of new cracks in the rock mass. This effect is in agreement with literature, when considering the peak particle velocity as a criterion for rock failure in tunnels. In the intermediate zone, where velocities range between 7S0-1000 m/s, damage to a much lesser extent occurs which is due mostly to growth of pre-existing cracks and widening of their apertures. The inner zone, where velocities exceed 1000 m/s, is considered to be unaffected by blasting. Simple remedial measures of low cost, which are based on blasting mechanics are proposed to minimise the blast induced damage zone and consequently the transition zone.

Jan 1, 1995

By Ariti J

The mineralogy and extractive metallurgy of platinum and palladium in ores and residues is examined and the relative reactivity of Pt, Pd, PtS and PdS in cyanide and chloride media at 20¦C is discussed. Electrochemical measurements establish that Pd is readily leached in chloride media but more slowly in cyanide media due to a passivating PdO film. The passivating oxide film on Pt prevents leaching in either system at ambient temperatures. The results of leaching Au, Pd and Pt from an iron oxide residue obtained from the Sherritt Gordon Process using CN/air and Cl-/H202 are compared. It appears that passivation is overcome either by roasting at ?600¦ or by leaching at >_100¦C.

Jan 1, 1991

By Dugan K. J

Mine operators are currently in a situation where market forces are acting to reduce profit margins and at the same time, regulatory bodies are insisting on improved mine safety and stability. This means that ground support must be made more cost efficient while maximising operator and equipment safety.A key aspect of ground support efficiency is the 'in the ground' performance. This paper discusses the factors that influence the way rock bolts and cable bolts perform. It highlights the need to know how support efficiency varies in different ground conditions.

Jan 1, 1992

By Higuchi K

In this paper, the history of Japanese coal and gas outbursts is presented and circumstances and countermeasures at the time cf outbursts are summarized statistically. Then the present meth- ods for prevention used practically in Japan are introduced. From statistics, it was reconfirmed that Japanese coal and gas outbursts have occur- ed frequently in the district of geological disturbance, symptoms immediately before out- burst occurrence were the phenomena in connec- tion with failure of a coal seam and outbursts have occurred many times when the number of boreholes had not been sufficient to degas. One of the principal protective method adopted in Japan is the large diameter gas drainage boring which also posesses a stress relief effects. There is a tendency to make diameter of borehole larger to increase both stress relief and degassing effects.

Jan 1, 1986

The Porgcra gold deposit is an epithermal gold base-metal deposit located in the Enga Province of Papua New Guinea. Gold-silver- spha le rite-galena-pyrite mineralization is related to stocks and dykes of dioritic composition which have intruded a series of folded marine sediments, mainly shales and siltstones, often with calcareous and carbon- aceous horizons, of middle Jurassic to middle Eocene age. The most intensely mineralized zone is at Waruwari Hill, where the mineralization occurs predominantly as massive mixed sulphide veins, and less frequently as quartz-chlorite veins and as disseminations. Mineralization occurs in all rock types and several phases of mineralization have been Recognized.

Jan 1, 1980

By Behl S

Flocculation behaviour of six different dolomite samples, four from the Florida mining district, one from Perry, South Georgia and another from New Jersey was examined using polyethylene oxide (PEO) as a flocculant. The samples were similar in chemical composition, however the porosity of the samples from the Florida mining district was higher than the others. FT-IR, adsorption and surface modification by leaching revealed that flocculation was directly related to the presence of isolated hydroxyl groups on the surface. The adsorption mechanism was believed to be hydrogen bonding of the ether oxygen of PEO with isolated -OH sites on the solid.

Jan 1, 1993