Search Documents

By Reuel A. Cochrane, Harry H. Angst

The successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. Rock Formations At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally in the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. Jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1943

By Strathmore R. B. Cooke, Thomas E. Bam

The paper discusses the mineralogy, structure, and strength of magnetite pellets fired in air and in a neutral atmosphere at various temperatures. The information obtained from this investigation is used to explain the origin of the structures occurring in pellets produced by pilot-plant operation. MUCH experimental work has been performed on i-VL the mechanism of agglomeration and pelletiz-ing of moist ore and concentrates and on the process of firing agglomerates, but except for the work of Tigerschiold and Ilmonil much of the published information is empirical, and the literature contains no information concerning the structure of fired pellets. Results of a preliminary study of the micro-structures occurring in pellets produced both in the laboratory and on a pilot-plant scale are presented in this paper. Most of the results were obtained from pellets prepared from Mesabi magnetic taconite, but through the courtesy of the staffs of the Minnesota Mines Experiment Station and the Bethlehem Steel Co., fired pellets produced from limonite and hematite ores and from Lebanon magnetite have also been examined. The work has been restricted almost entirely to pellets produced without additives, the exceptions being those in which coal was added to the filter cake before rolling. Schwartz has described the microstructures occurring in ore sinters produced under reducing conditions.' Many of the structures and constituents he describes are common to fired pellets, but the constituents normally occur in markedly different proportions. His statement that "in all satisfactory sinter the amount of hematite is small, perhaps not over 2 or 3 per cent" is inapplicable to pellets produced by pilot plant operation or by any process in which air is not deliberately excluded. Pilot plant pellets contain over 90 pct by weight of hematite, and those produced in the smaller furnaces of the Minnesota Mines Experiment Station contain more than 80 pct of that constituent. Preparation of Specimens It is difficult to examine unfired pellets microscopically because of their insufficient coherency to withstand sectioning and polishing. Fired pellets sometimes lack coherency and frequently contain holes which are troublesome during polishing. Impregnation of both air-dried and fired pellets is readily accomplished by the use of methyl metha-crylate monomer." The dry pellets are covered in a test tube with excess monomer, to which a small amount of accelerator has been added. When the test tube is placed in a cooling bath and evacuated with an aspirator, most of the entrapped air is removed, and disruption of weak pellets by boiling of the monomer is reduced to a minimum. Polymerization is then effected by immersion of the test tube in a water-bath at about 45"C, this temperature being held for 4 or 5 days. The test tube may then be broken away from the solidified mass and the pellets sectioned by a carborundum wheel or a diamond saw. Where time is important, impregnation is carried out at a higher temperature by Meyer's method.' Air-dried pellets must be impregnated with especial care; otherwise swelling occurs and the solids are displaced. It is more important to be certain that the monomer forms a reasonably complete network throughout the specimen than that all entrained air is removed, and for this reason the vacuum technique may be omitted. Impregnated agglomerated products and pellets are extremely coherent, section well, and may be polished either by hand or by machine. Hand polishing is not satisfactory for the examination of conditions existing at the boundaries of grains, and for this machine polishing must be used. The Graton-Vanderwilt machine gives excellent results, provided that pressure on the specimen is considerably in excess of that recommended by the manufacturer. Mineralogy of Fired Pellets Only two opaque iron minerals, magnetite and hematite, have been recognized in pellets. The complete identity of, these artificial minerals with their corresponding natural counterparts is shown by their mineralographic characteristics and their X-ray structures. Wiistite has not been found. Slag is the most common transparent constituent of fired pellets. Occasionally conditions have been appropriate for the crystallization of fayalite from the slag, and at other times another crystalline sil-

Jan 1, 1953

By C. B. Clark, W. H. Bruckner

Since the end of World War II interest has been increasing in the use of shaped charges in the mining industry and in other industries using explosives for blasting purposes. Shaped charges employ the principle known as the "Munroe effect," which was discovered by Charles E. Mun-roe more than 50 years ago (in 1888). Details of their design have been explained elsewhere.1,2,3 Fig I shows the essential features of design of two types of shaped charges (with conical and hemispherical cavities) and a schematic sketch of their action upon detonation. The following discussion deals with the behavior of the metal in the cavity liners when they are subjected to intense Pressures exerted when the explosive charge is detonated. Among the conclusions reached in research On shaped explosive charges, the following have been established concerning cavity liners:1'2 I. The optimum wall thickness of a conical cavity liner is dependent upon the apex angle of the 'One as well as On the base diameter of the charge. Acute apex angles require thinner walls for optimum perfmnance and more obtuse angles require thicker walls for the same base diameter' 2. Cones were more effective in forming a penetrating jet when the walls were tapered; that is, the thickness of the wall of the cone increased from the apex down. 3. The physical and mechanical properties of metals have a marked effect upon their performance as cavity-liner material. Boiling point, ductility, malleability, tensile strength, and hardness are among the properties that influence the effectiveness of a metal used as a cavity liner. Lead, for example, makes a wide, flat crater in steel plates. Aluminum makes a deeper crater than lead, and an aluminum alloy having a high tensile strength makes a deeper hole, but slightly smaller in diameter. Cast iron makes a deep, narrow hole. These findings, together with the following analysis under Metallographic Survey of slug, offer solutions to many of the problems involved in solving the mechanism of the formation of Munroe jets. It has been fairly well established that cavity liners collapse in a manner similar to that indicated in Fig 2, Conical liners are known to collapse upon themselves while hemispherical liners are believed to turn inside out in the process of jet formation. The first has been definitely proved by recovery of collapsed portions of cones, while liners from partly detonated charges show that hemispheres may turn inside out. Fig 3 shows a sketch of a recovered slug from a 6-in. shaped charge using a 45° cone made of cast iron. (This size of charge drilled holes up to 3 ft in depth in solid granodiorite.)

Jan 1, 1949

By H. W. Maynor, C. J. McHargue

DURING the course of an investigation of materials suitable for use as thermocouples at elevated temperatures by one of the authors, several nlolybdenum-rhenium alloys were prepared. Micrographs of an annealed alloy containing 25 pct Re (intended concentration; analysis not obtained) showed a number of twins, Fig. 1, suggesting a face-centered cubic structure. This note reports the structure and recrystallized wire texture of an alloy containing 25 wt pct Re. Alloys were prepared from 99.9 pct Mo (Fansteel Metallurgical Corp.) and rhenium obtained from the University of Tennessee (purity unreported). Powders were combined and briquetted at 56,000 psi and sintering was carried out at 2400°C for 5 hr in vacuum. Ingots so prepared were swaged at 982.2" to 1037.8oC into wires 0.036 in. diameter, a reduction in diameter of 85.6 pct. These wires were vacuum-annealed 1 hr at 2000°C. A North American Philips 114.59 mm powder camera and nickel-filtered copper radiation were used for structure determination. For the texture determination a Laue-type camera was used with zirconium-filtered molybdenum radiation and, because of the high background, aluminum foil was mounted next to the film. Exposures were taken with the wire perpendicular to the X-ray beam and tilted by 10". It was found that the X-ray pattern could be indexed on the basis of a face-centered cubic structure. Because of difficulties associated with obtaining a good X-ray pattern for this material, accurate parameter determinations were not made. An indicated parameter value of 3.70A was obtained. The X-ray data are given in Table I. The annealed wire texture was observed to be a sharp [111] texture. The spread about this fiber axis was k8" at the surface of the 0.036 in. wire. The annealed wire textures of aluminum have been reported as retention of the [Ill] deformation texture for anneals below 500°C and a new [1121 texture for anneals above 600°C.1 In copper wires, with a [Ill] plus [loo] deformation texture, results indicate a retention of this texture for annealing at lower temperatures and new components or the disappearance of components for annealing at higher temperatures.' The presence of the strong [I111 texture in the molybdenum-rhenium alloy after a 2000 °C anneal suggests that the deformation texture was the same. Acknowledgment The wires used in this study were prepared and heat-treated at the Institute for Atomic Research, and Ames Laboratory, Iowa State College, and the authors wish to express their thanks to the Institute for allowing the use of the material and permission to publish the results.

Jan 1, 1954

By J. D. Grace

Screening by centrifugal force is a unique subject, for all vibrating screens, with but one exception, depend on gravity alone to pass material through a sizing mesh or screen cloth. Centrifugal screening is one of the greatest advancements made in screening since the development of vibrating screens. It makes possible sizing in a range previously im-practical by mechanical methods. The centrifugal screen is specially designed for fine sizing from No. 4 separations to finer than No. 100 separations. Centrifugal force provides a positive control of factors that make fine particle separation practical and effective as opposed to gravity which is a fixed force acting only in a fixed direction, The centrifugal screen provides a control of the force of material against the screening surface, and also controls the distance of departure of the material from the surface and its rate of return. The centrifugal screen has a rotating drum that becomes a natural fan blowing air outward through the material being screened and carrying float dust and fines through the apertures with it. Screening by centrifugal force is an unique subject, for with the exception of only one vibrating screen presently on the market, all vibrating screens depend upon gravity to pass material through a sizing mesh or screen cloth. This one screen that sizes by centrifugal force and utilizes gravity only to convey material along the screen, is the Symons V-Screen. The requirements of the industrial minerals industry to meet ever-increasing stringent fine sizing specifications by a practical mechanical method accentuates the weakness of gravity, a fixed force acting in a fixed direction, as a prime force for fine sizing. It was apparent a force other than gravity was needed. This led to the development of a centrifugal screen to meet modern demands for practical fine sizing operations. Gyratory-type screens in use today were originally designed in a day when a 1/4-in. separation was normally considered fine sizing and 1/8-in. separations were extremely fine sizing. Although gyratory-type screens are sometimes used for separating below 1/8-in., they are not practical screens for this purpose. They were not designed to do this type of work. A growing demand for a practical means of making positive mechanical separations in a range of from 1/8 in. downward led to the development of the vibrating screen. These screens utilize higher speeds and lower amplitudes of vibration than

Jan 1, 1967

By M. R. Geer, H. F. Yancey, P. S. Jacobsen

Two growing problems confront the preparation engineer—still further restrictions on stream pollution and a greater proportion of fine coal as more and more continuous miners come into use. The de-watering screens, centrifuges, and settling ponds that sufficed a few years ago must often be supplemented by more effective equipment, and in some instances the finest solids are now being recovered by vacuum filtration, once considered too costly in many coal washeries. Unfortunately not all slurries can be readily filtered. Some are virtually unfilter-able, and others do not permit the high cake rates needed to hold costs within reason. Often, however, these difficult slurries can be rendered filterable by flocculation. Starch and lime have long increased settling rate in thickeners and can also aid filtration. More recently there have been other flocculants, primarily synthetic polymers or gums. Reports of their great effectiveness prompted the U. S. Bureau of Mines to test their use in filtration as part of its program on recovering and cleaning fine coal. The object of the present work was to compare some of the newer flocculants with starch and lime and to test the reaction of different types of slurries to flocculation. Three natural slurries, three synthetic coal-clay mixtures, and five flocculants were tested, all with a laboratory filter leaf. Slurries and Flocculants Tested: First of the slurries was the thickener feed from the washed coal section of the Michel colliery of Crow's Nest Pass Co. Ltd., Michel, B.C. As shown by the screen and ash analyses in Table I, practically all this slurry was finer than 28 mesh, and about half the solids were finer than 200. Substantially all material coarser than 200 mesh was clean coal, but the ash content of 20.7 pct in the finest size indicates a moderate amount of impurity. This coal is medium-volatile bituminous in rank. Slurry was also obtained from the Black Diamond washery of Palmer Coking Coal Co., King County, Wash. This underflow of a 1/2-mm vibrating slurry screen is a waste product discharged to a settling pond. As shown by the data in Table I it contained about 20 pct material finer than 200 mesh, which analyzed 77.5 pct ash, indicating a high proportion of clay. The coarser sizes were also high in ash content because of the presence of bone and shale. Black Diamond coal is on the dividing line between bituminous and subbituminous rank. The third slurry, from the washery of Roslyn-Cascade Coal Co. in Kittitas County, Wash., was the underflow of a battery of 8-in. cyclones that is wasted with the coarser refuse from the plant. In both size and ash content this slurry was similar to the Black Diamond, but since it was a cyclone-underflow product, the fraction finer than 200 mesh undoubtedly contained a much smaller proportion of finely divided clay than was present in the Black Diamond slurry. The Roslyn-Cascade coal is high-volatile A bituminous in rank. Initially the slurry samples were stored in the laboratory at a concentration of 40 pct solids. A progressive change in filtration and flocculation characteristics during storage was noted, however, presumably because of progressive disintegration of the clay. After careful testing demonstrated that the slurry solids could be dried and then repulped without changing the original filtration characteristics, this procedure was adopted. The flocculants used were Separan 2610, Kylo 27, Jaguar MD-A, Idaho potato starch, and lime. The lime was used as a slurry, the Separan 2610 as a 0.10 pct aqueous solution, and the other flocculants as 0.50 pct aqueous solutions. The starch was causti-cized with sodium hydroxide before use. As some of the flocculants are reported to deteriorate on storage, new batches of flocculants were prepared every two days. Test Procedure: Fig. 1 diagrams the filter leaf apparatus employed. This consists of a test leaf having an effective area of 0.10 sq ft., a 60°, 8 1/2-in. diam cone to hold the slurry sample, a variable-speed electric stirrer, vacuum gage, bleed line for controlling vacuum, filtrate flask, moisture trap, and vacuum pump. Two filter cloths were selected—Saran SA 603, a monofilament, coarse-weave cloth, and polyethylene PO-801 HF, a monofilament, fine-weave cloth. The Saran was selected to provide maximum cake rate without regard to clarity of filtrate and the polyethylene to provide the best quality of filtrate without regard to cake rate. The test charge for the filtering vessel consisted of 800 g of solids (previously soaked for 24 hr) and

Jan 1, 1960

By J. E. Hilliard

Various methods are given for estimating the number per unit volume and average size of convex particles from measurements on a projection through a slice of the structure. The determination of the size distribution is considered specifically for spherical particles. The results are applicable to any type of transmission microscopy and also to the correction of measurements made by reflected light on semitransparent materials. WITH the advent of electron transmission microscopy, the metallurgist is confronted with the problem of relating a projected image to the three-dimensional properties of the structure. This paper deals with the estimation of the number per unit volume and size of particles dispersed in a matrix. The case of convex particles will first be treated (the results will be applicable as approximations to particles of more general shape) and then spherical particles will be considered specifically. The latter represent a special case frequently encountered in practice and one which is also amenable to a calculation of the effect of overlap on the observed particle-size distribution. Although the present treatment was prompted by the needs of the electron microscopist, the results are applicable to transmission studies with any type of radiation. In addition, they can be used in the analysis of semitransparent materials by reflected light, the depth of light penetration corresponding to the thickness of the slice or section used in the transmission studies. 1) CONVEX PARTICLES 1.1) General Expression for N,. We will suppose that a "center" (such as the center of mass) is assigned to each particle. The convention used for defining the center is immaterial providing it does not depend on the orientation or location of the particle. Consider a slice through the structure having a pair of parallel faces a distance t apart. It will be assumed that the slice is randomly located with respect to its perpendicular distance from some fixed point, but it is not necessary to assume that its orientation is random. Our problem is to deduce the relationship between the number of par- ticle images seen on an orthogonal projection through the slice with the number, Nv, of particles per unit volume in the original structure.* *Symbols are listed in the Table. The expected number of particles with centers lying within the slice is Nvt per unit area. In addition, there will be elements in the slice contributed by particles whose centers lie without. The number of such elements will be the same as the number of intersections occurring on a two-dimensional plane through the structure; namely N~K, where K is the mean distance, Fig. 1, between tangent planes to a particle averaged over all particles, i.e., Where Ni is the number of particles of class i having the same shape and size, and pi (4, 8) is the probability that an i particle will have a given orientation with respect to the slice. If the particles are randomly oriented, then K is independent of the orientation of the slice and equal to the mean cali-per diameter. The total number of particle elements in the slice is therefore Nv(t + K) per unit area, but fewer will be seen as separate images on the projection plane because of overlap. If MA is the number of elements "lost" by overlap, the number of images per unit area will be NA = Nv(t + K) -MA 121 MA is a function of the slice thickness and must vanish at t = 0. As t increases, NA at first increases, reaches a maximum, and thereafter decreases as the overlap term MA becomes predomi-

Jan 1, 1962

By Arthur F. Taggart

Some years ago, A. M. Gaudin and one of the authors published a paper showing removal of tar acids from solution by sulfides preferentially as compared to gangues (specifically by galena as compared to quartz).' The underlying phenomenon was classed as adsorption, and the paper went on to develop the general thesis that so far as water-soluble frothing and collecting agents in flotation are concerned, the phenomenon of adsorption is one of controlling importance. Adsorption was defined in that paper as "a process of rearrangement of a system, which results in establishing a difference in concentration, as between the interfacial layers and the bulk of the phases, of a substance or substances initially uniformly dispersed in one or several of the phases." The paper went on to develop the relation between adsorption and surface cnergy according to Gibbs' equation (which may be thrown into the form U/c = KdT/dc, where U = excess concentration in surface layer, c = concentration, T = surface tension, and K is a constant), and pointed out that, according to this equation, degree of adsorption and change in surface tension vary directly. The present paper offers a somewhat different definition for the term adsorption; and sets up, in sweeping terms, the generalization that simple chemical reaction underlies the functioning of the flotation reagents which control mineral collection, when these reagents are soluble in and act from solution in the water of the pulp. Adsorption According to the modified definition, adsorption means concentration at an interface between different phases in a heterogeneous system (thus far the definition runs as before), by the action of some mechanism, of which nothing is properly implied in the word, and concerning which the user of the word is probably in entire ignorance. Thus defined,

Jan 1, 1930

By C. B. Clark, W. H. Bruckner

Since the end of World War II interest has been increasing in the use of shaped charges in the mining industry and in other industries using explosives for blasting purposes. Shaped charges employ the principle known as the "Munroe effect," which was discovered by Charles E. Mun-roe more than 50 years ago (in 1888). Details of their design have been explained elsewhere.1,2,3 Fig I shows the essential features of design of two types of shaped charges (with conical and hemispherical cavities) and a schematic sketch of their action upon detonation. The following discussion deals with the behavior of the metal in the cavity liners when they are subjected to intense Pressures exerted when the explosive charge is detonated. Among the conclusions reached in research On shaped explosive charges, the following have been established concerning cavity liners:1'2 I. The optimum wall thickness of a conical cavity liner is dependent upon the apex angle of the 'One as well as On the base diameter of the charge. Acute apex angles require thinner walls for optimum perfmnance and more obtuse angles require thicker walls for the same base diameter' 2. Cones were more effective in forming a penetrating jet when the walls were tapered; that is, the thickness of the wall of the cone increased from the apex down. 3. The physical and mechanical properties of metals have a marked effect upon their performance as cavity-liner material. Boiling point, ductility, malleability, tensile strength, and hardness are among the properties that influence the effectiveness of a metal used as a cavity liner. Lead, for example, makes a wide, flat crater in steel plates. Aluminum makes a deeper crater than lead, and an aluminum alloy having a high tensile strength makes a deeper hole, but slightly smaller in diameter. Cast iron makes a deep, narrow hole. These findings, together with the following analysis under Metallographic Survey of slug, offer solutions to many of the problems involved in solving the mechanism of the formation of Munroe jets. It has been fairly well established that cavity liners collapse in a manner similar to that indicated in Fig 2, Conical liners are known to collapse upon themselves while hemispherical liners are believed to turn inside out in the process of jet formation. The first has been definitely proved by recovery of collapsed portions of cones, while liners from partly detonated charges show that hemispheres may turn inside out. Fig 3 shows a sketch of a recovered slug from a 6-in. shaped charge using a 45° cone made of cast iron. (This size of charge drilled holes up to 3 ft in depth in solid granodiorite.)

Jan 1, 1949

By Hokuichiro Ohmachi

INTRODUCTION Metallic minerals have been formed only through complex geologic processes which took place at certain stages of the earth's histrory. Their concentration, abundance, and distribution are, therefore, restricted geologically, and very small in global scale. Ore is a mineral deposit or mineral concentration from which metals can be economically extracted by the contemporaneous technology. By this definition, several factors should be considered before any mineral deposit is regarded as an ore. The grade of mineral concentration and the scale of the reserve are most important. Demand for the metal and its price are the other factors. Advancement of technology in mining and extraction are also vital. Copper, for example, is now commonly extracted from the ores containing less than 0.3% of the metal. However, in the 1700's the common minerable grade was about 13%, and in the 1900's between 5 to 2.5%. This decrease in minerable grade is a function of not only the demand for copper, but also technological progress in mining and metal extraction in this case. Availability of ores has recently been subject to political factors, which were not the primary concern in the past. The petroleum of the Middle East is the prominent example. The metallic minerals are classified into three categories. The first one is the minerals free from these factors mentioned above. Iron and manganese belong to this category. The second category include aluminum, copper, nickel, cobalt, titanium, lead and zinc. These metals can be provided by the future progress in technology which enables the use of lower grade deposits. The third one represents the metals whose occurrence is geologically limited, and, thus, subject to the political factors. Niobium and tantalium are the example. In this article, I discuss these minerals in detail to give an outline of the factors which brought their concentration, distribution and availability. SELECTED MINERAL CONCENTRATIONS Iron Major iron ore deposits are the features of the relics of ancient continental crusts. They are found in all the continents where the Precambrian rocks expose. They do not occur in the oldest rocks (3,000my old) nor in the youngest ones (600my old). They are sedimentary rocks, normally, exhibiting alternations of bands of iron oxides (magnetite and hematite) or iron silicates (especially greenalite), and bands of silica, variously described as jasper, quartzite and chert. The best known banded iron ore deposits exist in the Lake Superior region of the North America, and their distribution extends at intervals to Labrador of Canada. Other examples occur in the U.S.S.R. Brazil, Venezela, India, the mainland China, and southern and western Africa (Liberia and Guines) (Table 1). Recently large deposits have been discovered in the Hammersley region of the western Australia, and northern and central region of Brazil. These ore deposits were originally formed in shallow seas where simple but abundant life existed. After the deposition, enrichment processes , related to tropical weathering, have brought about wholesale removal of silica to produce the deposits of best quality. Ores with 50-60% iron represent the best products in the Precambrian fields. Since local reserves of this high grade ores approach to exhaustion, benefication processes have been used effectively to upgrade much leaner ores (for example, taconite with 20-25% iron in Minesota, U.S.A.). There are two other types of iron deposits. Ironstone, a sedimentary rock containing goethite, chamosite and siderite, first appeared in early Paleozoic times in the stratigraphic record, and reached its Zenith in the Jurassic. Similar bedded iron deposits are found in the belt from the Cleveland Hills to Oxford in England, and in the "minette" oolitic ores of Alsace-Lorraine in Luxenburg and France. The iron content of these ironstones seldom exceed 30%, but they usually contain calcite and are self-fluxing. They also have phosphorous as undesirable impurity. Because of the grade and impurities, they require more fuel than the Precambrian ores. The third type of iron ore is associated with igneous activity and consists of magnetite and some hematite, and apatite. This deposit is believed to be a product of magmatic differenciation. It occurs in Kiruna of Arctic Sweden. The iron ore, therefore, present no global shortage problem. They extend to considerable depths. Their concentration is largest among the metals. If low grades were treated, the resource can be stepped up much substantially. Manganese Manganese is a ferro--alloy metal, thus, essential to the manufacture of sound steel. Manganese comes from manganese oxide and silicate ores. Many minerals contain manganese, but only a few oxides, silicates, and, in some places, carbonates (rhodecrosite) are mined as ore. Types of manganese deposits are bedded, massive,

Jan 1, 1982

By P. Chiotti, R. J. Hecht

Vapov pressure data of solid and liquid alloys along with phase diagram data WERE employed in calculating the thermodynamic properties for the Ca-Zn system. The relative excess partial molal free energy for zinc in the liquid alloys was fitted to the relation wnvre i is we tvmpvrutiirc in ucgrees neivtu ana in is the tr~ole fvaction. Relations for the standard free energy of fortnation for the eight cornpounds were developed. ThE phase diagram for the Ca-Zn system as determined by Messing et a1.' is reproduced in Fig. 1. Earlier work on the phase diagram has been summarized by Hansen and Anderko2 and the very limited thermodynamic information for this system has been reviewed by Hultgren et a1.3 The heat of fusion for the compound CaZn2 has recently been determined to be 9260 cal per mole.4 Solubility data for calcium in zinc for the temperature range of 650" to 725°C were fitted by the relation and reported by Johnson and Dilloon5 In the present investigation zinc vapor pressure data were obtained by both the dewpoint and Knudsen methods in order to calculate the thermodynamic properties for liquid and solid alloys. The dewpoint method as employed in this work requires that only one of the components be significantly volatile, in this case zinc, and that the vapor pressure of pure zinc be known. For calculation purposes the vapor pressure data for pure zinc3 were fitted to the relations; for temperatures below 692.7K, the melting point of zinc. The corresponding free-energy relations for vaporization and sublimation of pure zinc are respectively. Some of the calculations also required knowledge of the free energy of fusion of zinc and calcium and the free energy for the 721°K allotropic transformation of calcium. The free energy of fusion of zinc was taken to be the difference between Eqs. [4] and [5], or The free energy of fusion and transition for calcium were based on the enthalpy values of 2040 and 222 cal per g-atom, respectively, as reported by Chiotti et al. 4 and the heat capacity data given by Hultgren et a1.3 and are represented by the relations, In the latter expression the difference in heat capacity between the a and 0 forms of calcium was neglected. MATERIALS AND EXPERIMENTAL PROCEDURES The metals used in preparing the alloys were Bunker Hill slab zinc, 99.99 pct pure, and Ames Laboratory calcium. The average impurities in the calcium in parts per million by weight, ppm, were N-17, H—77, Ba—216, Mg-15, Si—7, C—157, and Fe—9. The zinc was cleaned in dilute nitric acid and the calcium was used as received. The calcium was stored and handled in an argon-filled glove box and when removed from the dry box it was kept in an argon-filled desiccator. Tantalum was found to be a suitable alloy container. The alloy components were contained in a 1-in.-diam cylindri-

Jan 1, 1968

By Paul A. Filteau

Asbestos ranks among the leading minerals produced in Canada. It is also mined in Russia, Rhodesia, South Africa, Cyprus, Italy, the U.S.A., Japan, China and several other countries. The most abundant variety, chrysotile, and also the most valuable form of asbestos produced, makes up 90% of the world's supply. In Canada, chrysotile is found in the provinces of British Columbia, Ontario, Newfoundland as well as in Quebec, the latter accounting for almost 90% of all the fibre produced in this country. A number of developments emerging this year could make 1968 a record production and export year for Canada's asbestos mining industry. Asbestos fibre consumption in increasing in the U.S., Canada, up 10% to date this year, Japan and in Latin America. Demand in Western Europe is again on the upswing, following a cut-back last year. As a result, shipments from Canadian mines for the first eight months of this year reached some 916,968 tons versus 873,402 in 1967, an increase of 43,566 tons or 5%. Indications are that Canadian asbestos production will for the first time ever top 1.5 million tons in 1968.

Jan 1, 1969

By G. W. Healy

Activities of oxides in the ternary FeO-MnO-SiO system are calculated from data on the binaries, using the Gibbs -Schuhmann method. These activity data are used, together with thermodynamic relations, to calculate the contents of oxygen, silicon, and manganese in liquid iron, and the composition of the corresponding oxide phases in equilibrium with it. Excellent agreement was found between calculated and experimental metal compositions, indicating that thermodynamic methods, such as those presented, can supply useful data on slag-metal equilibria, and are therefore capable of wider application. When molten steel containing oxygen is treated with a deoxidizer, the product of the reaction is composed of the oxides of the deoxidizing elements together with more or less iron oxide. This assemblage of oxides is presumably very close to equilibrium with the melt since it is formed directly from elements dissolved in it. Therefore, it is likely that metal analyses corresponding to a given oxide phase composition are calculable with considerable precision where sufficient information is available on activities in both phases. The present study was made to test this hypothesis in the case of deoxidation by silicon and manganese. Here experimental data on the relationship among oxygen, silicon, and manganese in the metal phase are available, as are activity data for the MnO-SiO2, FeO-SiO2, and FeO-MnO binary systems. A further objective was to demonstrate in a specific example how gaps in the data may be filled by judicious interpolation, and how the Gibbs-Schuhmann method is applied to obtain activities in ternary systems. The rigorous derivation of the latter, requiring considerable facility in handling partial differential equations, tends to mask the real simplicity of the method, and repel the very engineers and experimenters who would benefit the most from its use. I) GENERAL PROCEDURE Deoxidation of steel with silicon and manganese results in the formation of two phases, metal and oxide. The number of components is four—Fe, Mn, Si, and 0. The phase rule then gives the number of degrees of freedom: If temperature and pressure are fixed, 2 deg of freedom remain. Consequently, it suffices to fix the concentration of two of the components of the system for all the concentrations to be determined and, at least in principle, calculable. The practical problem is then to discover a straightforward method of calculation with a minimum of trial and error solutions. The type of reactions to be dealt with are like the following: Si (in steel) + 2 O(in steel) = SiO2(in oxide phase) The standard free energy of this reaction is readily obtained from the literature, so that the equilibrium constant can be calculated by the expression: Since the metallurgist is concerned with percentages rather than activities, a real solution requires information that will permit activities to be converted to concentrations. This information is fairly adequate for the elements dissolved in molten steel, but is not available for the FeO-MnO-SiO2 oxide system. Therefore, the first step in this study was to find the relation between activity and concentration for the three oxides making up the system. The next step was the calculation of slag and metal compositions that are in equilibrium with one another. As shown by the phase rule, it is sufficient to assume the values of two composition variables in order to calculate the rest. But which two are picked makes a vast difference in how difficult the calculation turns out to be, so that it is necessary to make preliminary trial of several routes to find the easiest one. A convenient method is to begin with the slag, and to pick FeO concentration and that of one of the other oxides. Starting with the relation between oxygen dissolved in the liquid steel and FeO in the slag permits a good first estimate to be made of the oxygen content of the steel in equilibrium with FeO, because the iron content being fairly close to 100 pct, Fe has an activity close to unity. Using this first estimate of oxygen activity, approximate values of the manganese and silicon contents of the melt are readily calculated from the appropriate equilibrium constants. A minor correction for the depar-

Jan 1, 1963

By David R. Mitchell, R. M. Fleming

MANY trends were evident in the coal industry during 1951. Some were favorable for the industry; others were not. Probably those having the most far-reaching consequences are those affecting coal's markets. The rapid dieselization of many railroads and the continued trend toward oil and natural gas for home heating has caused serious dislocations in various mining districts. Mines have been forced to close down or to work on a reduced time basis. Conversely the increased activity in the metallurgical industries has increased the demand for coking and special purpose coals, and the growing production of electric energy has increased the demand in certain areas for steam coals. The increased demand for metallurgical coal and for steam raising by the large utilities is more than equal tonnage-wise to the loss of coal to railroad dieselization and conversions to oil and gas in the domestic market. Since much of the expansion is at captive mines of large corporations, many commercial operators supplying railroad and domestic users have had their markets curtailed without any compensating demand from other sources. Feverish activity was in evidence in many areas by commercial operators attempting to find new markets. The Norfolk and Western Railway is the, only major American railroad committed to the burning of coal. It has an exceptionally good cost record. During 1951, fifteen additional modern coal-burning steam switching locomotives were authorized for construction in the company's Roanoke shops at a cost of about $1,450,000. When the new order is completed the road will own a total of sixty locomotives of the modern-switcher type, including thirty acquired by purchase last year. The Norfolk and Western today is the only American railroad building its own motive power. All of these locomotives burn coal. Production Coal production in the year 1951 will approximate 570 million tons of anthracite, bituminous coal, and lignite. Of this, approximately 7 pet is anthracite. Total production is approximately 30 million tons more than in 1950 and reflects the increase in general industrial activity. Exports are expected to be close to 50 million tons. The industrial stockpile is close to 75 million tons, the highest it has been since 1943. With the exception of the usual local stoppages the year 1951 was unmarked by labor disputes. It was a year of good labor-management relations with a negotiated wage increase unmarred by a work stoppage. This may be the beginning. of an era of sensible negotiations to find agreeable settlements of disputes without the usual protracted bickering and industry-wide strike. The United Mine Workers of America has condemned wildcat strikes, stating that in nearly every, instance proper grievance procedures have not been instituted. Government defense organizations, perhaps profiting by their experiences during World War II, are pursuing a more enlightened program with regard to the fuel requirements of the nation. Many prominent officials have stated that wherever possible coal should be considered the primary source of fuel in all defense expansion. With the increased consumption of steel by defense projects, approval of transportation facilities for liquid and gaseous fuels have been refused where these fuels would enter a coal producing area. Liquid and gaseous fuel producers also have failed to provide satisfactory evidence that they have sufficient reserves and are capable of supplying their product in adequate amounts for the periods of time required. Realization has at last become prevalent that the hydro-electric power installations in several areas are insufficient to handle increased demands.' Steam generating plants are being constructed in these areas and equipped to burn coal. Most notable of these, is the TWA area whose supplemental steam power plants are expected to consume 10 million tons of coal per year when completed. The Pacific Northwest is another area which is expected to follow the same pattern. Nearly all new steam-power generating plants are being equipped to burn coal either as a primary fuel or as an emergency measure. Metallurgical Coal The steel and other metallurgical industries are expanding rapidly to meet increased industrial demands and defense orders. Since these industries are dependent on coke, coke has had a year of high production and can be expected to break all existing records when steel-plant expansions are completed. Most notable of the expansion projects is that of the Delaware River area where the iron ore will be received by ship from Canada and South America. U. S. Steel is only one of several steel corporations that are planning on putting integrated steel producing units in this area. The Defense Solids Fuels Administration announced in December that through. November 30, 1951. 29 projects in eight states, with a total cost of

Jan 1, 1952

By Arthur Phillips

THE normal method of preparing metallic alloys for commercial use involves the preparation of a melt containing the given components in the chosen proportions and allowing the homogeneous liquid mass to solidify in a mold of the desired form. The solidification is frequently accompanied by a segregation of the alloying elements in different parts of the casting. When the segregation is occasioned primarily by marked differences in density of the solid and liquid phases, it is termed "gravity" segregation. When the segregation conforms to a. selective freezing in harmony with the teachings of the equilibrium diagram of the alloy system-i.e., the lower melting phases are concentrated in the regions of the casting last to freeze-it is often referred to as " normal" segrega-tion. However, in many cases the lower-melting part of the system is concentrated in the parts of the casting first to freeze and the result in this case is termed "inverse" segregation. To complete the. terminology of the subject, normal segregation in a single phase is usually called "coring" and the word will be used in that sense in this paper. Inverse segregation, particularly when the liquid phase is exuded or sweated out on the surface of the casting, is sometimes called "location." Unfortunately, some ambiguity has arisen from the use of this term and it is perhaps advisable to confine its use to the dictionary definition; namely, "The separation of two phases by heat sufficient to melt one but not the other." The gravity and normal types of segregation are both well understood and to some extent are controllable by taking advantage of the most favorable cooling rate for a given casting condition. Inverse segregation has received considerable attention from several investigators- but none of the theories offered seem to account in a convincing way for the many examples of this type. The observations made in the present work on segregation in single crystals, and in some other castings, tend to support one theory of the mechanism of inverse segregation and definitely to

Jan 1, 1937

By K. E. Brown, J. P. Brill, T. C. Doerr

A wide range of intermittent gas-lift tests way conducted in a 1,500-ft experimental well through 11/4- and 11/2-in, nominal size tubing. The well was equipped with two gas-lift valves, four Maihak electronic pressure transmitters and surface facilities to measure casing and tubing pressures, temperature, liquid production and the rate and volume of gas injected. For each tubing size, tests were conducted varying the slug length, gas volume injected and liquid viscosity and surface tension. From these tests, an empirical "fallback" or liquid loss correlation has been developed. No general fallback correlation could be obtained, and the correlation is presented in the form of one curve for each slug length of a given liquid and lubing size. A conceptual model has been developed which combines the fallback correlation with equarions which govern liquid slug pow. A mathematical simulation of the model in the form of a digital computer program is used to calculate total recovery, gas volume used and clearance time for a given test. Tubing pressures at the gas-lift valve and at the gm-slug interface are calculated as a function of time. Tubing pressures at the surface during slug clearance ore also calculated. The results compare favorably with the test data and verify the conceptual model. The extent to which the model can be used for other tubing sizes, depths, liquids and gas-lift valves can only be determined with additional experimental data. Data are also necessary so that a fallback curve can be constructed for the particular test conditions studied. INTRODUCTION The flow of liquid slugs in vertical conduits has long been an established production method in the petroleum industry. Under the name "intermittent gas lift", many advances have been made in engineering design. However, the unsteady-state nature of liquid slug flow has discouraged attempts to describe the problem analytically. The result has been that intermittent gas lift is dominated by rules-of-thumb engineering practices developed over many years. The advent of slim-hole completions has increased the demand for a more rigorous solution to the intermittent problem. Small-diameter conduits offer more frictional per intermittent cycle. Small-diameter conduits are defined to be 1%-in. nominal size tubing or smaller. When oil is produced from the reservoir in which it is found, and transported to surface tanks by intermittent gas lift, three separate flow stages are encountered: flow of the fluids to the wellbore through a porous medium, vertical flow of a liquid slug from the point of gas injection to the surface, and horizontal flow of the liquid slug through the surface flowlines from the wellhead to the surface tanks. The three stages are depicted schematically in Fig. 1. The present study deals with liquid slug flow in both the vertical and horizontal conduits, ending when the bottom of the liquid slug reaches the surface. Due to the large number of variables involved, the analytical study of intermittent gas lift is extremely complex. The possibility of flow regimes other than slug type, the nature of the force fields acting on the system, the interfacial instabilities involved, the varying operational principles of existing gas-lift valves and the complete unsteady-state nature of the physical phenomena occurring in an intermittent gas-lift cycle relate some of the difficulties encountered.

By John D. Roach

DURING an investigation of the yttrium-hydrogen system aimed at producing solid yttrium hydride specimens containing various amounts of hydrogen, it was observed that yttrium containing approximately 2 wt pct H exhibited a tendency to crack and crumble to a powder on standing in air at room temperature. It was also observed that longer hydriding times, at a given temperature, increased this susceptibility to powdering without an increase in hydrogen content, also that moisture in the air is necessary for the observed effects to occur. Even if cracking did not occur, there was a continual formation of a light gray powder on the as-treated surface of the hydrided yttrium and this reaction continues until the entire hydrided piece has been reduced to a powder. Storing the hydrided specimens in the absence of air or removing the surface either by machining or grinding were effective means of preventing this disintegration of hydrided yttrium. In an attempt to determine the reason for this powdering phenomenon, the surfaces of a number of as-hydrided yttrium specimens were examined by X-ray techniques. In all cases the X-ray pattern obtained showed the major phase to be yttrium hydride (YH2) as would be expected since the specimens contained 2 to 2.2 wt pct H. In some cases a trace of yttrium oxide was observed. There was also a third phase present on the surface of these hydrided specimens which could not immediately be identified. This unknown phase was a face-centered cubic material, NaC1-type structure, with a lattice parameter of 4.855 and a calculated density of 5.914 g per cc. Very slight hand polishing of the surface of the hydrided yttrium specimens completely removed both the unknown phase and the traces of oxide so that only the yttrium hydride pattern remained. Based on the X-ray patterns the quantity of the unknown phase on the surface of the hydrided yttrium appeared to be directly related to the susceptibility of the material to powdering. Work at the Denver Research Institute on the yttrium-nitrogen binary system showed that yttrium nitride (YN) is a face-centered cubic material with a lattice parameter of 4.878A and a density of 5.890 g per cc. They also noted that this compound rapidly disintegrated to a powder on standing in air. The unknown pattern observed in the above specimens corresponds very closely to that of the nitride—fcc structure, 4.885 parameter, and density of 5.914 g per cc. The presence of this thin film of nitride on the surface of the hydrided specimens probably accounts for the observed powder formation and crumbling. The nitride reacts with the water vapor in the air (verified by private communication from Dr. C. Huffine, General Electric Co.) to yield yttrium oxide and ammonia. Ammonia is readily detected when hydrided yttrium specimens were allowed to stand in bottled moist air. The powder formed on the surface of the hydrided specimens was shown by X-ray analysis to be yttrium oxide. This reaction appears to occur primarily at the grain boundaries since discrete particles of yttrium hydride separate from the specimens during this powdering process. The reaction of yttrium nitride with water vapor is believed to be as follows: 2YN + 3H2O - Y203 + 2NH3. Despite the fact that this nitride is present only as an extremely thin surface film, if the above reaction is not prevented by removing this film from the surface either by machining or grinding, the reaction continues until the entire hydrided piece has been reduced to a powder. To account for this continuation of the reaction, it is believed that the following reactionalsooccurs: 2YH2 + 2NH3 -2YN + 5H2. The nitride produced by the latter reaction reacts in turn with water vapor. The reaction therefore becomes autocatalytic and continues until the hydride has been consumed and the entire piece reduced to oxide powder. The amount of nitride required to initiate this reaction is quite small and this nitrogen contamination can occur from a number of sources—hydrogen gas employed, minute leak in the hydriding apparatus or even from degassing of the reaction vessel itself. Longer hydriding times increase the possibility of nitrogen contamination and this is especially true when a dynamic gas system is employed in the hydriding process. The production of stable, solid hydrided yttrium is dependent on the complete absence of nitrogen contamination during processing. If such contamination does occur, powdering of the hydrided product can be prevented by removing the nitride from the surface e.g. grinding or by preventing access of air to the pieces e.g. sealing in wax or plastic. The author wishes to express his appreciation to General Electric Co. for sponsoring this research and for permission to publish the results of work under Subcontract AT-93.

Jan 1, 1962

By A. Satter

Studies of wellbore heat transtnission during the injection of a hot fluid, as either gas or liquid, have appeared in he literature. The present investigation takes into account the effect of condensation, which is of practical sig-nificance when considering steam injection operations. Calculation procedures are given for superheated and for saturated and undersaturated steam. Effects of injection rate, time, pressure, temperature and depth of a well on heat losses have been analyzed. The benefits of using a packer are discussed. Also presented are correlations for estimating heat losses involved during injection of saturated steam. INTRODUCTION Studies of wellbore heat losses during the injection of a hot fluid have appeared in the literature. Ramey' has presented a useful solution for calculating temperature of a heated gas as a function of depth and injection time. Ramey and others have also presented solutions for the hot liquid case.'. ' No method is available to take into account the effect of condensation, which is of practical significance when considering steam injection operations. This paper presents a method of estimating the quality of a condensing fluid as a function of depth and time. The approach is basically the same as that used by Ramey. The following injected fluids and conditions are considered in this study: 1. Injection of superheated steam A. Decrease in temperature until cooled to the saturated state B. Condensation until condensed completely into hot (saturated) water 2. Injection of saturated or undersaturated steam; condensation until condensed completely into hot (saturated) water. Although this investigation does not include cooling of water after steam is completely condensed, Ramey's solution for the hot liquid case can be used for this purpose. The effects of various process variables on heat losses During the injection of steam into a well are investigated. THEORY QUALITY OF CONDENSING STEAM Predicting the behavior of condensing steam flowing down the injection wellbore requires an estimate of the quality of steam, i.e., the mass fraction of vapor in the mixture. Let us divide the total depth of the injection well into several segments which might be, but do not have to be, of equal magnitude. Consider condensation within a given depth interval AZ, the bottom of which is located at a depth Z from the surface (Fig 1). The following equation, derived in the Appendix- relates the quality of steam at the bottom of an interval to that at the top of the interval:

Jan 1, 1966

By Norman Goss

IT is generally agreed that cold-working mechanically refines the grains into smaller fragments and with continued working these are oriented with certain crystallographic directions bearing a relation to the direction in which the metal is worked. Some of the energy expended on the metal during plastic deformation appears in the form of heat, but a very small portion remains in the metal as stored energy. The entropy, specific heat capacity, temperature at which recrystallization will just begin, density, ductility, elasticity, tensile strength, and resistance to corrosion are affected. These properties have been studied extensively and some of the changes in the physical properties due to cold-working were attributed to lattice distortion.1-8 The broadening of the K. lines on the X-ray diffraction diagrams of plastically deformed metals is believed to indicate lattice distortion, and consequently the existence of internal stresses. The evidence supporting this theory rests solely upon the observed experimental fact that the dif-fraction lines are broadened and the K a doublets are completely diffused. Elam9 has reviewed the matter of lattice distortion in relationship to the hardening of metals by plastic deformation. The X-ray diagrams of plastically deformed metals differ in general from annealed metals. The hardening of a metal was believed due to lattice distortion.9 The resolu-tion of the doublet is lost when a metal is cold-worked and the Lane spots are elongated. At one time this elongation was thought to indicate the elastic bending of the crystal planes. However, more careful work showed that the asterism was due to new orientations developed within the fragmented grains during plastic deformation. Some theories attrib-uted the hardening to fragmentation of the grains into smaller units.

Jan 1, 1940

By Alden Greninger

THE time-honored description of the growth of metal crystals to form polycrystalline aggregates is one in which two important steps are con-sidered: (1) nucleation, and (2) dendritic growth, each dendrite starting from its individual nucleus and resulting (upon slow cooling, assuming no solid phase changes) in a macrograin. This picture of the process of crystallization is incomplete, and it is with the hope of enlarging upon it that the following summary and correlation of experimental results are given. MOSAIC STRUCTURE For an exact definition of the mosaic structure of metal crystals-if, indeed, one can be found that will hold for all metals-one must await the results of much experimental work in this field. The writer's investiga-tions have been confined almost entirely to copper and a few of its alloys. The following terms are proposed, and will be used in this report: Macromosaic Structure l.-Large-scale mosaic structure; more specif-ically, mosaic structure of a scale large enough to produce splitting of Laue spots on back-reflection Laue X-ray patterns2. The deviation from exact parallelism of neighboring macromosaics varies from a few

Jan 1, 1935