Search Documents

Stope support systems, typically consisting of props and packs, are used extensively in the gold and platinum mining industry to stabilize the rock mass in the excavation vicinity and to reduce the hazard associated with rockfalls and rockbursts. The design of stope support systems was historically based predominantly on past experience and practices, and cost considerations. The recent development of a new and improved support design methodology, has led to the potential for significant increases in worker safety and support cost savings. This paper reviews some of the fundamental rock mass and support criteria that form the basis of the improved support design methodology. The considered design criteria are the height of potential fall; quasi-static stope closure rates; dynamic stope closure rates; compressive hangingwall stresses; discontinuity spacing, orientation and interface properties; effect of support length (stoping width); effect of compression rate; consistency of support performance; a real coverage; support spacing; and zone of support influence. The proposed support design methodology combines both the zone of influence and key block stability theories, resulting in optimized support systems for rockfall and rockburst conditions. The site-specific methodology consists of two stages: (i) a tributary area analysis, and (ii) a zone of support influence and a stability analysis, considering hangingwall failure due to buckling, shear and block rotation, which gives maximum safe spacing of individual support units. The methodology is suitable for designing support systems for both blocky hangingwalls and hangingwalls fragmented by face-parallel extension and shear fractures.

Jan 1, 2001

Disseminated gold mineralization in the Vunda River area 12 km SE of Lautoka in Viti Levu occurs sporadically in shoshonite volcanics within an alteration area of some 6 km2. No definite intrusions have yet been located though possible intrusions occur toward the centre and on the eastern margin of the area. The nature and distribution of alteration suggests the presence of a co-magmatic mineralizing stock just below the surface.The gold occurs within close spaced fractures and occasionally around the c1asts of breccia and agglomerate.Various types of alteration compatible with porphyry mineralization occur, but to date show no zoning or defined correlation with incidence of gold which occurs in various alteration facies.It is suggested that the gold and trace copper mineralization at Vunda arises from the sub-volcanic intrusive phase (monzonite) of the Sambeto shoshonite (5 m.y.) and is part of an E-W zone of porphyry-type mineralizationtrending easterly to the Kingston porphyry copper deposit at Navilawa.There is a close similarity between the Vunda mineralization and some of the porphyry deposits of alkali affinity in British Columbia, Canada.

Jan 1, 1978

By Gualberto Salas

Dado que la voladura es una de las operaciones unitarias de mayor extracción del mineral -en tanto logra una adecuada fragmentación de la roca con un costo reducido, es necesario lograr una interrelación entre los resultados de la voladura y el de las operaciones unitarias como herramientas que evalúan y optimizan los diseños de los disparos. En ese sentido, el presente trabajo describe las técnicas para el diseño de las mallas de perforación, los programas para la simulación de la voladura y también para medir los resultados, que permitirán realizar los ajustes necesarios para mejorar los resultados de fragmentación y reducir el costo de operación de minado.

Sep 13, 2001

By Creasey J. W, Huntington J. F

Faults cutting the Lithgow and Katoomba seams in some collieries of the Western Coalfield can be classified, on the basis of spatial pattern, into three principal groups: meridional swarms of closely spaced minor faults and associated joints, with throws of less than 0.5 m and with exceptional faults of up to 5 m; isolated interswarm strike-slip faults in the Lithgow seam and widely spaced strike-slip faults in swarms in the Katoomba seam; and low-angle normal faults associated with the Lidsdale-Lithgow seam split.Orientations of faults and coal cleats in the coalfield are presented on stereoplots and histograms, as a basis for an analysis of fault dynamics. The low-angle normal faults were found to have been formed only along the Lidsdale-Lithgow seam split, and before the high-angle faults. The origin of the high-angle normal faults in the meridional swarms is discussed and it is suggested that basementcover interactions must have occurred. This suggestion is supported by geophysical evidence. Low-amplitude monoclines in the coal seam, and the spacing of swarms 0.9 to 4.5 km apart, may be due to the underlying basement structure.It is clear that postextensional compressive deformation of swarms in the coalfield gave rise to shortening by minor thrust development, and probably also caused the synchronous strike-slip movement on pre-existing normal faults. There is evidence to show that isolated interswarm strike-slip faults in the Lithgow seam, and widely spaced strike-slip faults in the Katoomba seam, may have originated synchronously with such thrusts. The axis of maximum principal compression ('71) for the thrust event was inferred to be near horizontal and aligned approximately E-W. Recent rock mechanics measurements of the present day stress field indicate a similar stress configuration.

Jan 1, 1981

The mineralogy and microstructure of mattes from the nickel flash smelter at Kalgoorlie, Western Australia, have been studied. The flash furnace matte consisted mainly of an intimate mixture of pentlandite and heazlewoodite with some nickel metal. The electric furnace matte was mainly an iron-nickel alloy with subsidiary pentlandite while the converter matte consisted mainly of heazlewoodite with crystals of nickel metal.

Jan 1, 1977

By C. A. Geffen

This report, sponsored by the U. S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the com¬ponent operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982

By Fidelis T. Suorineni

Rapid drifting enables quicker access to orebodies, higher production rates and a resultant reduction in production cost. The Mining Innovation, Rehabilitation and Applied Research Corporation (MIRARCO) funded by the Canadian Mining Industry Research Organization (CAMIRO) has developed a methodology for safe rapid drift development within the underground metalliferrous mining industry in Canada According to industry survey, about 36% of drift development cycle time is spent on support installation. MIRARCO has developed a methodology for safe rapid drift development based on minimizing time spent on support installation. The methodology includes a critical review of the rockmass classification systems, examination of current support practices in the mining industry and civil tunneling, review of rapid drift development practice in South Africa, introduction of risk hazard procedures to account for material property variability and the development of a WIZARD as a quick decision-making tool for the implementation of the procedures. A comprehensive field data collection procedure was put in place and data collected from various mines to verify and calibrate the support selection rationale. The findings of the research programme resulted in the development of an improved rockmass classification system and showed that construction effects have drastic influence on support levels but is often not accounted for in assessing support levels. Stress effects and structurally controlled failures are the other important factors to take into account in rapid drift development. Three support classes were established for safe rapid drift development as No Systematic Support, Light Support and Strong Support. The support levels took into account cost, rate of installation and safety based on compatibility with ground characteristics. This paper describes the methodology for safe rapid drifting within the underground metalliferrous mining industry in Canada and highlights the key issues and major drivers behind their continued development at the Geomechanics Research Centre within MIRARCO.

May 1, 2004

By Christopher Mark, Gregory M. Molinda, Timothy M. Barton

The Coal Mine Roof Rating (CMRR) was first presented at this Conference nine years ago. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, and extended cut evaluation. It has also become truly international, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. The purpose of this paper is to bring the mining community up to date with recent improvements and applications of the CMRR. The most important new development is a streamlined process for determining the CMRR from exploratory drill core. Just three types of information are now required: •Fracture spacing (or RQD) •Uniaxial compressive strength (or axial Point Load Testing) •Diametral Point Load Testing The moisture sensitivity adjustment has also been changed, and new research has related the immersion test to slake durability. Most recently, the CMRR has been implemented in a computer program, which can be obtained from NIOSH free of charge. The program facilitates calculation of the CMRR from either underground or drill core data. Values from many locations can be saved in a single file, and an interface with Autocad allows CMRR contour plots to be integrated into mine planning.

By W. W. Adams

This bulletin covers all mines in the United States that were operated in 1936 to produce metallic ores and all mines that were operated to produce nonmetallic minerals other than coal, stone, sand, gravel, or their products. Reports from mine operators revealed a better safety record for fatal accidents in 1936 than in any other year except 1934 during the 26 years for which annual surveys of accidents in the mineral industries of the United States have been conducted by the Bureau of Mines. On the other hand, the record for nonfatal injuries, although better in 1936 than in any year prior to 1930, was not as good as it was from 1930 to 1935, inclusive.

Jan 1, 1939

By Michael R. Walsh, John H. Wright, Eivind B. Jensen

A tunnel boring machine (TBM) was designed and built at the Cold Regions Research and Engineering Laboratory in 1992 for use in Antarctica. The TBM system was tested at the South Pole where a 120-m long tunnel was bored to prove the concept. Modifications were made to the system resulting from this work. In 1999,boring of a 600-mutilidor began as part of the new South Pole Station. Tunneler hydraulics reliability problems prevented the completion of the tunnel before the end of the short construction season. This paper discusses the design and operation of the TBM, proposed solutions to the problems encountered, and current operations of the system.

Jan 1, 2001

By J. R. Kyte, L. A. Rapoport

The material balance equation for partiai or complete 1:trter-drivc reser1,oir.s been re-arranged to include a pressure irrferferencr ternr. This pressure interfernce term was ohtained from the theory established hy Morinda. A .successful progranl deissed to solve the resrclritlg c,qrration in a few hours on a nleelitr .sizeti, digital compuier. No prior knowdelge of the properties of the eqrrifer is required in the solution. 7' ri~rl calculations areatle using various assumed con!binuiions of value of the constant expretsing the qquifer properties correspoinds to the best fit ohtained between observed and calculated field history. Details of the method of calculaion are illus trated by an example. INTKCDUCTICN A method 01' calculating the material balance equation for a partial water-drive reservoir completed in an aquifer has been described in the literature." Pressure interference i'rc,m other pools iocated in the same nquiucr is not taken into account in this solution. When present, the pres- sure interference effect must be included in order to make a complete performance analysis. A correction for this effect has been developed using the theory cstahlished by Mor-tada.' Manual calculation of the material balance for water-drive reservoirs is a formidable task. Such manual ca1culation when interference eflects are includcd would be impossible to completc in any reasonable time period. However, a medium-sized stored program, digltal conlputer can he used satisfactorily. The method is described in the following sections. THECKETICAL CONSIDEKATIOhS The material balance equation for a reservoir producing by partial or total water drive, as proposed by Van Everdingen, This relationship is linear for Z/a from which thc slopc, Z, and the intercept, N, can be obtained by the least-squares method from the data points. It is not necessary lo know the aquifer properties to uktain oplimum values tor 2nd IV. Various assumptions are made tor At,,: where 11 is production time, seconds (oilfield between the equal successive time intervals into which the history is divided. t,, h It, times the number of equal time periods from i.e.. the total dimen-sionless time interval from It is noted that the dinlensionless time interval, At,,, involves all the relevant aquifer properties. Accordingly, any assunlption of is an assumption of the combined aquifer properties which pertain to the solution of the equation. Deviations of the data points from a straight line arc calculated for each assumption of and the value of A, correspond ing to the minimunl deviation is chosen as the optimum solution. This method is described in Ref. 1 and 2. Thc material balance solution is usually made with an initial assumption that the reservoir being studied is located in an infinite aquifer from which there are no other withdrawals. Deviation of the points by amounts greater than can be attributed to inaccuracies in field data may be the result of: (1) boundary effects of a limited aquifer, (2) pressure interference from othcr pools completed in the .sarne aquifer, and (3) a combination of these effects. Differentiation of these effects can be made only on the basis of geologic data. Pressure interference from other fields will result in a pressure drop at the original oil-water boundary having an interference component, The measured instantaneous pressure drops at the oil-water

To many Australian Mining Engineers, we take it, the singular features of banket deposits are not as familiarly known as they would wish, possibly because in the majority of instances they are not in touch with the South African milling world, and have had little opportunity of studying the development of the banket beds, either from correspondence or literature. The writer hazards this opinion feelingly, because, when in Australia and before he had visited Africa, the utmost knowledge he was able to obtnin was a mass of conflicting theoretic discussion as to the agencies which formed the banket bed, without any practical hints as to their geological horizon, the rocks with which they are associated, the usual appearance and character of the ore, in fine, without that everyday detailed description which the miner requires when seeking information regarding mineral or metal deposit foreign in character to any that he has yet studied, or as yet had any opportunity of studying in his own country.The writer recognised that many more able men than he have from time to time discussed the features and formation of the banket beds of the land, notwithstanding which and feeling that many of his Australian colleagues have found themselves in a similar position regarding accurate detailed information respecting these African banket deposits as he himself was, he hopes that the present paper on the said deposits, as found on the fields under notice, will prove useful to some and of interest to all.

By Richard Weinstein, Richard Snoby

There are many advantages to upgrading coal with dry jigging technology. The most obvious is the lack of process water, which eliminates the need for fines dewatering and slurry confinement. Dry jigging eliminates the clean coal moisture penalty associated with wet processing. Particulate emissions are virtually nonexistent due to inclusions of fabric dust collectors on all modern dry jig plants. Because of the environmentally friendly nature of dry jig plants, installation permits are often measured in days, not months. There has also been a fundamental advance in dry jigging efficiency. All of these advantages have renewed the coal industry’s interest in dry jigging. But air jigging is not right for every application. There are limitations due to particle size, particle shape, moisture and near gravity content. This article explores the evolution of dry jigging. It reviews parameters important for determining the suitability of dry jigging. It also compares historical performance data as measured by imperfection, against results from modern dry jigging technology. The article also presents data from modern dry jig installations.

Jan 1, 2007

Australia is tightening its rules governing mineral processing and the purchase of rural land by foreign investors" Rural land purchasers in the future will have to demonstrate to the Foreign Investment Review Board, the applicable governing body, that they will introduce new techniques or developments that will benefit Australia. In mineral processing, the criterion will be the availability of maximum opportunities for Australian equity capital. The changes are designed to discourage absentee landlords and speculators from abroad. A diamond field discovered several years ago in the northern section of Western Australia, known as the Kimberley region, is now thought to be one of the largest in the world, according to Conzinc Riotinto of Australia Ltd. (CRA). Figures released late in 1981 by CRA indicate that the main orebody of at least 100 million metric tons contains possibly 500 million carats of diamonds with a conservative market value of $8 billion. The diamond stones in the 100-acre deposit are about 10% gem-quality, 30% near gem, and 60% industrial. Initial production is expected to be about 17 million carats annually, which could be expanded to 25 million carats annually. World production of natural diamonds has been about 40 million carats per year from a reserve base of about 700 million carats.

Jan 1, 1982

By Jacques Moraille

The public is asking for more aesthetic designs if they can be proven cost-effective at providing an appealing element to new dams. Lake Lenexa was designed and built around the idea of providing for basic dam functions such as flood control, enhanced water quality, recreation but also to provide an inviting community focal point for the residents to visit and enjoy; truly interact with the dam. The architecturally unique dam and ?one of a kind? spillway were designed to symbolize the water cycle as water moves from nature into the urban environment and the back to nature. A pedestrian bridge that spans the spillway offers visitors a good view of cascading pools and a fountain. The original Lake Lenexa dam layout incorporated relatively high, cast-in-place concrete retaining walls to form the spillway structure. The Black & Veatch project team performed a Value Engineering (VE) study to determine cost-effective means for implementing architectural features within the spillway, which resulted in innovative uses of construction materials not typically used in dam and reservoir construction. The VE study concluded that mechanically stabilized earth (MSE) retaining walls that are normally used for transportation projects would be a cost-effective alternative to the originally planned cast-in-place wall systems for the main spillway and stilling basins. The Black & Veatch study added value by mixing cement-kiln dust (CKD) with on-site clay soils to produce a stabilized material for use under the spillway. The CKD stabilized material properties include low compressibility, high strength and low permeability, which reduced seepage and uplift pressures under the spillway slabs. The cost savings provided by the VE alternatives reduced total costs and enabled architectural elements. The award winning dam design also used drilled caissons, expanded polystyrene (EPS) block forms, customized steel forms and external concrete vibrators to build the pedestrian bridge and upper spillway structures.

Jan 1, 2009

By Cordner G. D

Titanium is not yet being produced on a commercial scale despite the facts that it has some impressive properties, and that it occurs very abundantly in easily-mined, highgrade oxide ores. One important reason for this is that the excellent mechanical properties of the metal were not widely recognised and appreciated until about twenty years ago.Another factor which has tended to retard progress in titanium metallurgy has been the realization that the oxide minerals of titanium are very stable; in other words, considerable energy has to be expended to reduce the oxide to metal. Table 1 presents the minimum energies which would have to be expended to produce one ton of each of the metals, aluminium, magnesium, titanium and iron from their respective oxides under theoretically ideal conditions at normal temperature and pressure. At higher temperatures, the minimum energy requirements are different, but the values for the various metals still fall in the same order as indicated in Table 1.In actual fact, the energy consumption in the case of any particular metal is higher than the ideal value by an amount which can be determined only by' the results of plant practice. The only general conclusion that can be drawn from the data in Table 1 is that it might eventually prove...

Jan 1, 1950

A short account is given of the theory and practice of determining the true U3O8 content of ore samples by the determination of the beta and gamma activities separately, using the method of Eichholz and his associates.It is shown that, despite the variation of sample activity without change in U3O8 content, the true U3O8 value can still be found.Thorium can be determined simultaneously if this element is also present.

Jan 1, 1957

By D. W. Rich

An environmental management system (EMS) is a key part of a company?s environmental stewardship. Procedures and practices to continually improve environmental performance can provide great benefits in operating the company. Managing site environmental quality data is a key component of this. An environmental data management system (EDMS) is an important element of the EMS for mining and other projects, providing project staff with the information that they need to make decisions that can have a significant impact on public health. Improvements in computers, data communications, and transfer formats have made it much easier to implement an integrated EDMS program for gathering, managing, selecting, and displaying data from the field and the lab. Software now lets users define sampling plans, create files for field data entry, and print Chains of Custody. Laptop and handheld computers facilitate field data entry and may provide automated communication back to the office. Most labs can now create usable electronic data deliverables. QC checks and limit comparisons can be largely automated. The result is organized data that can be efficiently used for reporting, graphing, and mapping, to better understand project issues.

Jan 1, 2009

By James Westfield

Following is a resume of activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction o1 injuries at coal mines: 1. The Federal Mine Safety Code for Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines July 24, 1946, after consultation with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior October 8, 1953, after further consultations with representatives of management and mine workers and was incorporated by reference in the 1952 and subsequent bituminous coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bitumi¬nous coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. Federal coal-mine inspectors also had temporary authority to close mines found to be imminently dangerous, but such authority (under Executive Order 9728) was removed June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1959

By D. Vogt

South African underground hard rock mines are typically managed using measurements made daily, weekly or even monthly of key parameters such as face advance, readiness to blast, blast success, temperature or dust levels. Health, safety and productivity can all be greatly improved if a real-time measurement system can inform decision making. To enable this vision of widespread sensing, communication and decision support, CSIR has developed an open standard architecture for communication of sensor data, and a reference implementation using that standard. The standard, called AziSA, meaning ?to inform? in isiZulu, will allow any device that complies with it to join any network that supports it. The standard is designed for South African gold and platinum mines. To be practical in a typical Bushveld platinum mine, a real-time sensor system needs to be robust, reliable and cheap: ?Sensors are equipped with power sources that will last as long as the sensor is required. In effect, sensors need to be disposable: cheap enough not to warrant repair if they break. ?Communication in the stope is wireless, to avoid there liability problems associated with wire connections. For example, wires to sensors in the face area are unlikely to survive blasting. ?To get information out of the stope, the power line to the scraper winch is used as a communications link. Unlike a separate communications link, the power line will be repaired if damaged, because of its importance to production. ?Outside the stope, communications are transferred onto the mine communication infrastructure. To succeed as a management system, the next key element is the use of software decision support tools that will analyse masses of real-time data to extract key parameters and trends for decision makers. A range of sensors has been developed, including commercial sensors that have had wireless adapters added to make them AziSA compliant, and bespoke sensors that provide low cost sensing of typical mining parameters. An important parameter in any sensor network is the location of the sensor. This has to be easy and cheap to establish, so a tool has been developed to locate sensors in the confines of a stope, using ultrasonic and radio techniques. Once sensors are installed and located, they associate their location to all data that they produce. All the data from the system are captured at surface in a flexible database that can be queried by any application that requires data of any kind. It is simple to program alerts, and for actions to be associated with alerts. The use of wireless in stope also allows for communication from surface to the stope, or from stope to stope. The first implementation of an AziSA compliant system is being installed as part of the Mine Health and Safety Council funded rockfall elimination project. The design is discussed, and a future application for a platinum mine is considered.

Jan 1, 2009