Search Documents

By R. W. Fedors, S. T. Green, R. A. Hart, D. B. Walter

Computational fluid dynamic (CFD) modeling of a potential nuclear waste repository drift may be an important tool to estimate moisture redistribution caused by natural convection within the drift. To refine and support CFD techniques, a small laboratory cold-trap experiment was developed. Results from numerical modeling of the laboratory experiment show the sensitivity of the bulk air flow rate and average air temperature within the drift to several key parameters, including various boundary condition assumptions and surrounding porous media properties.

Jan 1, 2004

The distribution or the userul minerals or Tasmania is so closely connected with the geological structure of the island that it will be convenient to briefly recapitulate the principal ract or its geological history, before describing the ore and other deposits. In many cases these present features which are very puzzling in the absence of knowledge of the structure of the districts in which they are found and in all cases it is of benefit to mining engineers to be acquainted with the main facts of the geological·history of the regions in which they have to carry on operations. Moreover, in speculating as to the origin of lodes and other deposits, we have constantly to rerer to the crumplings or the earth's crust by mountain-making movements, and to the igneous rocks which have been thrust throngh the other strata, to explain the origin or the lode fissures, and this discussion cannot be carried on without knowledge of local geology.The oldest rock yet met with in Tasmania are of Archooan age, and consist of highly crystalline quartzites and micaceous schist. They are most extensively developed towards the western side ot the island, forming a belt parallel to the West Coast from South-West Cape to Cradle fountain; but they also crop out here and there to the west and northward of this belt, where the covering strata or later age have been denuded away. Though not seen in situ in the eastern part of the colony, the abundance or pebbles derived from this formation in the conglomerates of the coal measures shows that it must in those day have formed land surfaces there also, and makes it likely that the archooan strata exist at no great depth: below many of the beds of later age now occupying the surface. Lying unconfortably upon these highly metamorphic strata we find next an extensive series of subcrystalline metamorphic conglomerates, grits, sandstones, slates, and limestones,of Cambro-Silurian age. These are well seen in the Gordou River Basin, along the West Coast Range, aloug the North Coast, and in the goldfields of the north-eastern portion of the colony. They are much broken by later intrusive rocks, and covered by younger rormations, but the series is spread more or less over the whole island.

In order to maintain a production rate of 6,000 tonnes per day from underground at the Williams Operating Corporation, two independent mining areas were required which created a long narrow sill pillar between them. During initial mining of the sill pillar there were a number of significant ground falls [LeBlanc and Murdoch, 2000] and in March 1999, with no active mining ongoing in the sill pillar area, a rockburst of magnitude 3.0 Nuttli occurred. Extensive ground support was designed and installed to withstand events of similar magnitude [Bawden and Jones, 2002]. A mine wide microseismic system was installed to monitor mine induced seismic behaviour over the entire mine. The area most directly affected by the 1999 rockburst was rehabilitated using a highly ductile support design. Along with microseismic instrumentation, the areas were instrumented using conventional SMART Cables and SMART MPBX?s. Subsequent to this, the area was impacted by a large number of high magnitude seismic events [magnitudes between 1.7 and 3.5 Nuttli]. The ground support performed very well during these events, providing confidence in the mine?s ability to control the ground under severe rockburst conditions. Analyses of microseismic and conventional instrumentation, combined with numerical analyses of sequence alternatives, were used to develop an optimal mining strategy for the sill pillar area. The selected strategy involved utilization of instrumentation data and calibrated model results to analyze yield zones in the sill. The analyzed ?yielded? zones were assessed to be low seismic risk. Initial mining in the sill was then concentrated in these low risk areas, with the objective of further concentrating stress into the remaining seismically active area, in order to induce ultimate failure of the sill. Continuing large magnitude seismicity and resulting damage in the remaining ?high seismic risk? area, led to abandoning a second portion of the footwall access and the strategic decision to extract a stope near the centre of this zone in order to force final failure of the sill pillar. During execution of this plan two large magnitude seismic events occurred resulting in destressing and final failure of the remaining sill pillar. The paper provides a detailed description of this ?strategic mine sequence driven self-destressing process? and the implications to final extraction planning in this area of the mine.

Apr 1, 2005

By A. S. Haugh

OHSAS 18001 is a series of international standards for occupational health and safety management. It is comprised of two parts, 18001 and 180029. OHSAS 18001 was formulated by international certifying bodies and is based on BS8800 and was first published in 19996,11. OHSAS 18001 was developed to be compatible with ISO 9001 and ISO 14001 in order to facilitate integration of quality, environment, and occupational health and safety management systems5. It is a voluntary standard and the overall aim of OHSAS 18001 is to enable organizations to control their occupational health and safety (OH&S) risks and improve overall health and safety performance5. OHSAS 18001 is widely accepted in the UK, Europe, and Asia, is gaining momentum in North and South America, and it was used as the basis and conforms to the requirements of ANSI/AIHA Z.10-2005: American National Standard for Occupational Health and Safety Management Systems. It defines a set of requirements for an occupational health and safety management system suitable for any kind and size of organization4. Businesses of all sizes are developing and implementing occupational health and safety management systems (OHSMS) that are in compliance with the OHSAS 18001 standard.

Jan 1, 2012

By G. S. Hill, B. J. Huls

This paper on coarse particle recovery (CPR) summarizes a process to capture coarse particles that are not recoverable by regular flotation. Several porphyry copper operations in the world operate analogous circuits that recover non-floated copper from tailings; however, the case presented here is unique in that extensive underlying test work has allowed the authors to elucidate some fundamental principles behind recovery enhancement. This paper discusses an overview of the flowsheet that is proposed to Minera Escondida Ltda., the nature of copper in the feed to the CPR circuit, and the various unit operations within the recovery circuit.

Jan 1, 2006

By L. Xinghua

Limonite is a general term for a group of amorphous iron oxide and iron hydroxide materials. It is considered as one of the very refractory iron ore types due to its wide variation in chemical composition, iron content, moisture content and easily sliming in the course of comminution. Iron grade of test sample is 25.48%, the iron minerals are mainly limonite; and the gangue minerals consist of quartz and feldspar in majority, secondarily silicate minerals. In this test work, high intensity magnetic separation (HIMS)-cationic reverse flotation and magnetic roasting-low intensity magnetic separation (LIMS) tests were conducted on limonite ore. The test results show that the concentrate with iron grade of 50.97% and recovery of 68.50% can be obtained by HIMS-cationic reverse flotation technique; while using magnetic roasting-LIMS technique, the better concentrate indexes of iron grade of 60.36% and recovery of 89.71% are achieved, and the iron grade of tailing is only 4.42%. Therefore, the magnetic roasting-LIMS technique is a better suitable method for beneficiation of low-grade limonite ore. Keywords: Low-grade limonite; Mineralogy; HIMS; Cationic reverse flotation; Magnetic roasting; LIMS

Feb 27, 2013

By Maurice Grieves

GC. Waterman Mr. Grieves' paper on "Shaft Sinking Today--A Boring Business Tomorrow" in the Dec. 1981 issue of MINING ENGINEERING is an excellent description of recent improvements in speed and costs of shaft sinking. However, shaft boring techniques are not a recent development. In 1935-36, the Idaho Maryland Co. (gold), Grass Valley, CA, bored the vertical 1.5-m-diam Idaho No. 2 ventilation and supply shaft to a depth of 346 m. The equipment was designed and perfected by Branner Newsome and was, I believe, described in "Transactions." Pickands Mather later bored a 1.8-m-diam shaft to a depth of about 305 m using Newsome's design. The Idaho No. 2 shaft cut through hard gabbro, diabase dikes, soft serpentine, very incompetent ankeritized serpentine and a strong fault zone. The completed shaft did not require timber support; the fault zone was cemented. Equipment consisted of a rotating 1.5-m or 3-m core barrel with a slotted bottom which cut a 76-mm kerf. The cutting agent was chilled steel shot introduced into the slot as needed. The driving mechanism and core barrel were lowered into the shaft, the former secured to the wall and the inshaft "engineer" operated the motors which controlled core barrel rpm and advance. After an advance of 1.5-3 m the equipment was lifted out of the shaft, a half(?) stick of powder cut off the drilled core, and it was hoisted to the surface with a cable attached to an eye bolt at the tope of the core. A "shift" consisted of three men: hoistman, equipment operator (down the shaft), and a surface laborer. Advance was variable as equipment and techniques were perfected. Near the end of the job advance was, as I remember, 1.5-3 m per shift. Costs were, as I recall, about $115/m. Up to 4 m cores were lifted out in one piece and swung to the dump by a stiff leg derrick. The Newsome equipment was relatively inexpensive to build and operate and his method should be (more than?) competetive with the methods described by Grieves. W.E. Hawes The author, in mentioning the South African developments of the cactus grab, ignores the parallel development of the Cryderman mucker in this hemisphere. Perhaps a slightly longer history of blind hold drilling would have been in order. Blind shaft boring got a major boost at the Nevada Test Site, as part of the nuclear weapons development, when it was essential to be able to quickly assess depth for weapons testing. One of the early civilian attempts to utilize this technology occurred when Kerr McGee drilled the shaft at the Section 19 Mine at Ambrosia Lake, NM. This twin masted drill rig belonged to a subsidiary of Kerr McGee, not Shaft Drillers. This was a difficult hole, due to bentonitic shales that decomposed. Later advances in drilling fluids eliminated this problem. The Conoco project referred to is not entirely correct, and needs minor amplification: The depth of the development (not pilot) shaft drilled was 684 m, at a diameter of 3.05 m, with a 2.16 m ID hydratatic casing being installed to a depth of 669 m. Conoco Inc., not Challenger, executed the drilling, however Conoco did use Challenger Drilling Company's Rig 14-S. Rig 14-S is unique in that it is specifically designed for shaft drilling, rather than being an oil field rig used for this service. All work was planned and directed by Conoco personnel. Deviation of the aforementioned shaft from vertical was 31 cm. Two smaller shafts (pilot shafts) were drilled with the same rig. These smaller ones were drilled 1.8 m in diameter, to depth of 665 m and cased with .91-m-diam casing, to depth of 650 m to be used as pilot holes for 5.5 m diameter shafts. The total elapsed time for all drilling, casing, cementing, and rig moves was 50 weeks. The constraints mentioned of vertical accuracy, torque, wall collapse, rig set up time, lining time etc., pumping out, etc., may not be as serious as the author implies. First, vertical accuracy: The record achieved by Conoco indicates that with reasonable care, good accuracy can be obtained, primarily by having a fair amount of weight in tension, rather than on the drill bit. Second, the amount of torque that can be applied to the drill stem has been greatly increased by the introduction of larger diameter drill stems, such as the new Hughes rig uses. Third, risk of collapse of shaft walls is minimal with the proper mud program. Basically, the walls are supported by the weight of the mud and it is not removed until some type of casing is installed and grouted in. Here in the real challenge of blind drilling shafts to devise a more economical method of lining bored shafts than using steel casing. The remaining issues were minor at Conoco, provided adequate planning and scheduling takes place. An excellent paper, "Shaft Drilling--Crownpoint Project" by Hassell H. Hunter, presented at the Fifth Uranium Symposium in Albuquerque in Sept. 1981 contains details of this project. A combination of blind boring, with enlargement by either mechanical means (boring machine, or tunneling type shield) or slabbing down, with muck removal through a larger bored shaft would seem to be the future trend in shaft development. The economics, especially for wet conditions, favor this concept over conventional sinking, as has been demonstrated at Kerr McGee --Churchrock, UNC--Churchrock and Conoco at Crownpoint.

Jan 3, 1983

By D. E. Sherwood

Mr. Tamaro introduced his paper which concerned the construction of foundations for the buildings and related infrastructure of the World Financial Center on a reclaimed shoreline site at the Southern tip of Manhattan Island. This large project presented difficult design and construction problems, both geotechnical and structural. All structures were supported by foundations carried to rock. Two of the buildings were supported by conventional pier (pad) foundations constructed within diaphragm wall cofferdams. The remaining structures were supported by either piles to rock or caisson (large diameter) piles with socket depths drilled through the rock of up to 7.6 metres. Underground services, railway and proposed road tunnels all affected the installation of foundations. The proposed road tunnels for the new six lane 'Westway' would involve an excavation 12 metres deep adjacent to and under three buildings. This problem was solved by an agreement that tower windloads would be taken by the tower foundations and not distributed through the basement walls. This was achieved by a system of battered caissons founded on the rock and arranged so that adjacent caissons were founded in different rock masses. Diaphragm walls were restrained using tie backs. Ground testing indicated an exposure to D.C. stray current corrosion of all underground construction. As a result all of the foundations were isolated from the ground by non-conductive materials. In the case of piles and caissons the reinforcing for the caisson was fully protected by concrete and all outside steel used for the installation of piling was considered sacrificial and not used in the computation of long term load carrying capacity.

Jan 1, 1991

The Fraser Range is composed dominantly of basic pyroxene granulites derived from basalts, many of which appear to have been vesicular and pillowed. Acidic and basic garnet-bearing granulites are important in the west, and acidic granulites and narrow anorthosite layers are dominant in some regions east of the Fraser Range. An extensive flat-lying olivine gabbro sheet cuts the granulites, and in places has been converted to spineI-bearingmeta-gabbros and pyroxene granulites. The granulites of the Fraser Range (Proterozoic) are separated from the gneisses and schists of the goldfields regions (Archaean) by the Fraser Fault, over which there is a large gravity anomaly (gradient 20 milligals per mile). Some of the problems associated with the concentration of Cu, and Ni liberated from mineral lattices during metamorphism, and other principles of metal concentration in granulite terranes, are discussed. The recognition of vesicular and pillowed zones, even though highly metamorphosed, is of fundamental importance.

Jan 1, 1969

By Raymond P. Miller, David L. Monson, Robert A. Robinson

A geotechnical instrumentation program consisting of borehole extensometers and portable tape extensometer stations was effectively used to monitor concrete liner deformations and guide construction procedures during enlargement of a 75-year old Union Pacific Railroad tunnel in Wyoming. Enlargement involved excavation of the old concrete invert and placement of 5,941 feet of new concrete invert 6 feet lower in squeezing shales, fault zones and water-bearing sandstones. Instrumentation data were used to guide procedures for excavating the old invert, installation of temporary interior struts, underpinning existing liner walls, and placing the new concrete invert.

Jan 1, 1976

Process Simulation and Plant Design of a Mineral Selective Magnetising Flash Roasting Plant Using Neutrons

Sep 13, 2010

By A. Pratt

Portland cement is primarily used to solidify backfill in underground mine workings and it represents a major cost in mining operations. CANMET-MMSL has invented an alternative binder technology that does not contain any amount of Portland cement and is made using waste materials, such as development rock and smelter slag. The technology has been successfully tested with many types of base metal and ferrous slag. Research conducted in collaboration with several mining operations in Canada has shown that the CANMET-MMSL binder has considerable potential as a replacement for Portland cement in mine backfill. An integral part of the overall mining operation, backfill is used for two main purposes: safety and environmental remediation. Depending on the mining method used, backfill provides a working surface, stabilizes stope and pillar walls, as well as the surrounding rock mass, and controls caving of stope backs. There are several benefits associated with the replacement of Portland cement in backfill, including reductions in (i) the footprint by placement of slag waste underground, (ii) the environmental effects and long term liability resulting from disposal and containment of slag waste on surface such as acid rock drainage, (iii) GHG as a result of reduced Portland cement usage (the production of 1 ton of Portland cement produces 1 ton of GHG), and (iv) the significant costs associated with reduced Portland cement usage.

May 1, 2010

Most analysts determining tungsten trioxide in low grade samples are aware that colorimetric procedures do not possess the inherent disadvantages of gravimetric methods operating on milligram quantities of tungsten trioxide. Apart from the inaccuracies associated with weighing four or five milligrams of ignited oxide in a platinum crucible of about 30 gm. weight with a large surface area to absorb moisture, using a 5 gm. charge on samples less than about 0·15 per cent tungsten trioxide, it is extremely difficult toget complete or pure precipitation of tungsten with cinchonine, cinchonine plus alpha benzoin oxime, rhodamine B or any other of the commonly used precipitants. Table 2', No. 8, illustrates the low results obtained by gravimetric as opposed to colorimetric procedures. In addition the colorimetric determination requires only a small portion of the time consumed by gravimetric practices and the increased accuracy obtainable in low ranges together with the saving in time made it highly desirable to develop a colorimetric method suitable for King Island ores.The most commonly used colorimetric method is that introduced by Feigl and Krumholz (1932), since modified by various investigators (Grimaldi and North, 1943; Sandell, 1946; Westwood and Mayer, 1947; Gentry and Sherrington, 1948; Freund, Wright and Brookshier, 1951; Grouthamel and Johnson, 1954; and others). Stannous chloride is used to reduce tungsten followed by colour development with a thiocyanate, usually sodium, potassium or ammonium.Other reducing agents have been proposed (Emery and Curtis, 1948), but only in recent years have the conditions governing maximum colour development been fully estab...

Jan 1, 1958

By Thomas P. Mucho, Dennis R. Dolinar, Anthony T. Iannacchione

The Chestnut Ridge Anticline is a prominent structure in southwestern Pennsylvania, USA. This structure has brought two economically valuable limestone formations to the surface, where they are easily accessible to room-and-pillar mining. Nine active crushed stone quarries, an underground research facility, and one industrial facility currently operate along the linear trend that represents the axis of the anticline. The National Institute for Occupational Safety and Health (NIOSH) has identified significant variation in levels of horizontal stress within relatively short distances at shallow overburdens along the anticline. At one quarry, the horizontal stress is high enough to shear strata with a modulus of approximately 77 Gpa. Conversely, zones of extension were observed in parts of another quarry, indicating very low horizontal stress conditions. This study found that high levels of horizontal stress are to be expected in this very stiff rock formation and that local geologic and topographic structures are capable of altering the magnitude and possibly the orientation of the horizontal stress field.

By Javier A. Llano

GPS, wireless communications and on-board and off-board computing capabilities provide today’s mining companies with unprecedented process improvement and cost reduction opportunities. All aspects of the operation from engineering, surveying, drilling, loading, hauling and support can benefit from products like CAES and Drill Monitor. These technologies, which have been working at world class mines around the world in some cases for over three years, are helping customers achieve new lows in cost per ton. Manually intensive and time-consuming processes like in field surveying are replaced by timely mine status information wirelessly transmitted from the machines to the office.

Jul 17, 2000

By H. Linder, W. H. Dennen

The graphitic carbon content of soils may be used to detect and delimit subsurface graphitic zones. Spectrographic measurement of carbon in C horizon soils from several areas in the northeastern United States shows good correlation with known graphitic bodies. Bodies of graphite and sulfides are readily located by electromagnetic prospecting methods, but these methods cannot generally discriminate between them. Usual practice, therefore, requires follow-up work on electrically anomalous areas by trenching, drilling, or soil sampling in order to determine the mineralogical nature of the conductor. The efficiency and cost of such follow-up is consequently an important factor in prospecting. The presence of buried sulfide deposits is often reflected in concentrations of metals in the superincumbent soil. Simple chemical tests for such metal concentrations have been developed and applied with considerable success. Bodies of graphite or mixtures of graphite and sulfides are, however, very common and a means whereby buried graphite could be detected by soil testing should provide valuable additional information in the search for ore sulfide and graphite deposits. Graphite is a notably stable substance and should persist in soil above graphite-rich horizons. Microscopic examination of soil samples high in carbon, however, failed to reveal any recognizable graphite fragments indicating a grain size in the clay range. Presumably such small particles would have some mobility in a soil by a translocation mechanism similar to that proposed for the movement of clay particles in a soil profile. Experimental data supports this idea since the boundary between background and anomalous soils carbon values is quite sharp, but the anomalous zone is slightly broader than the graphitic source rock. A simple spectrochemical technique for the determination of carbon in geological materials has been described by Dennen,1 and may be directly applied to soils. A modification of this technique which employs an arcing chamber through which nitrogen is passed is recommended to decrease contributions from atmospheric carbon dioxide. Tests indicate that soils over graphitic zones may be strongly enriched in carbon. The spectrochemical determination of carbon depends upon the formation of the cyanogen molecule (CN) from carbon in a sample and atmospheric nitrogen, under the high temperatures associated with a dc arc. Samples for analysis are dried, lumps broken, and screened. A small portion of the -100 mesh fraction is packed into a copper electrode and excited as the cathode of a dc arc. The band spectra of cyanogen are recorded photographically and the density of the bandhead CN 3883A is measured. The limit of detection of the method is about 0.01 pct C and its coefficient of variation is about 15 pct. Soils, of course, contain carbon in other forms than graphite, and the amount of interference from such sources was examined. The C horizon of several soils from Massachusetts, Maine, and Pennsylvania were found to have a carbon content of 0.3 to 0.5 pct by weight. This content is chiefly due to the presence of carbonates and vegetable matter in the sample and may be readily eliminated, or at least

Jan 1, 1961

By L Teixeira, C J. Greet, P Karageorgos

Pyrite is ubiquitous within copper ores, and presents significant challenges to most operations in terms of its impact on copper sulfide concentrate grade and recovery.Samples of ore containing from 3 to 47 percent pyrite, with nominally the same chalcopyrite feed grade, were collected from a copper mine in eastern Australia for testing. The ores were ground under standard conditions using forged steel grinding media in the Magotteaux Mill® to determine the impact of increasing pyrite feed grade on the pulp chemistry of the system and subsequent rougher flotation response. Attempts were made to correlate the pulp chemical parameters (oxygen demand and EDTA extractable metal ions) with flotation behaviour to determine if one (or more) could be used as a metric to infer metallurgical behaviour.The observations made were then tested under different grinding environments (obtained using more electrochemically inert high chromium) grinding media to determine if they hold true.CITATION:Greet, C J, Karageorgos, P and Teixeira, L, 2015. The influence of pyrite on the pulp chemistry and copper flotation response of a chalcopyrite ore, in Proceedings MetPlant 2015, pp 175–187 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By David C. Grant

In situ uranium mining offers the advantages of minimal environmental disturbance, low capital and operating costs, and reduced mining development time. It is becoming an increasingly attractive mining method for the recovery of uranium from secondary ore deposits. In order to better understand the process, a laboratory technique was developed and used to study and simulate both the chemical and physical phenomena occurring in ore bodies during in situ leaching. The laboratory simulation technique has been used to determine effects of leaching variables on permeability uranium recovery, and post-leach aquifer restoration. This report describes the simulation system and testing procedure in sufficient detail to allow the construction of the system, and to perform the desired leaching tests. With construction of such a system, in situ leaching of a given ore using various leach conditions can be evaluated relatively rapidly in the laboratory. Not only could optimum leach conditions be selected for existing ore bodies, but also exploitation of new ore bodies could be accelerated.

Jan 1, 1985

By Hernán Parra

El presente trabajo señala la fase de tratamiento metalúrgico de pirrotitas que contienen oro, donde en la concentración por flotación se encontró un esquema adecuado para tratar pirrotitas auríferas considerando las restricciones ambientales que no permitieron incorporar técnicas de cianuración directa, que es como suelen tratarse es-tos minerales en el mundo. Asimismo, se propuso el uso de concentradores centrífugos para recuperar el oro libre fino en una primera etapa gravimé-trica, y concentradores de mesa Gemeni para obtener concentrados de alta cali-dad disponibles para fundición.

Sep 9, 2007

Yallourn brown coal and its characteristics have been the subject of innumerable papers and discussions. The Lurgi process adopted for the production of Towns gas by the gasification of brown coal has been described frequently in literature.The application of the Lurgi process for the gasification of Yallourn briquettes has naturally lead to some unexpected problems. Rather than attempt to review the whole field of experience gained in the first two years of operation of the gasification plant at Morwell, this paper attempts to describe two problems encountered, peculiar to the fuel used, and the steps taken in overcoming them.THE PROCESS AND PLANTTo clarify the conditions surrounding the problems, it is necessary to briefly describe the gasification and cooling processes and plant.Brown coal briquettes are gasified in a pressure generator, using a mixture of steam and oxygen as a gasifying medium. Crude gas produced in the generator is washed and cooled in the waste heat boiler and coolers. Figure 1 shows an arrangement of the generator and coolers. The gasifying medium enters the generator through a hollow shaft in the base. This shaft drives the grate, which has three purposes: (a) to distribute the gasifying medium into the fuel bed; (b) to extract the ash from the fuel bed; (c) to support the fuel bed.Briquettes enter the top of the generator through the coal lock chamber and the fuel bed is maintained at a reasonably...

Jan 1, 1960