Search Documents

Sluice box operating practices in Papua New Guinea (PNG), and published work on sluice boxes are briefly reviewed. Some recent work on sediment entrainment mechanisms occurring in sluice boxes have also been described. In the light of this information, some drawbacks in the commonly adopted sluice box operating practices in PNG, and ways of overcoming them, are also highlighted.

Jan 1, 1991

By T. W. Beck

Overexposure to respirable dust remains a widespread health hazard to roof bolter occupations in underground coal mines. Recently implemented mist drilling technology was evaluated for its effectiveness in controlling respirable dust exposures for roof bolting personnel. This work presents the findings from NIOSH field and laboratory studies comparing respirable dust levels on mist drilling roof bolter machines to dust levels measured on machines using a conventional vacuum drilling system. Gravimetric and instantaneous respirable dust samples were collected for multiple drilling cycles. These dust measurements were used to assess the potential dust control capabilities relative to conventional drilling. Controlled laboratory tests found 0.3 mg/m3 more respirable dust with mist drilling than with the conventional vacuum method. A separate field investigation of the two techniques observed higher dust levels around the mist bolting machine.

Jan 1, 2008

By D. R. Cook

This paper is a case history of an exploration venture for base metals, begun by the Rocky Mountain District of Bear Creek Mining Company in 1952 and completed in 1954. The project was based on the idea of W. S. Burbank, U. S. Geological Survey, that commercial deposits of base metals might occur in Paleozoic sediments beneath hydrothermally altered volcanic rocks in the Southern Bonanza mining district, Colorado. Here, an area of andesitic rocks, four square miles in extent, has been argillized, pyritized, chloritized and silicified. Geological, geophysical and geochemical studies were followed by the diamond drilling of three holes totalling 6,220 feet. Further alteration ang geochemical studies were made on the cores from these holes. A brief review of the alteration and geologic mapping, colored aerial photograph interpretation, geochemical soil and rock sampling, magnetic, gravity and radio-metric surveys are presented together with some conclusions regarding this work. This paper is a case history of an exploration venture for base metals, begun by the Rocky Mountain District of Bear Creek Mining Company in 1952 and completed in 1954. Important contributions were made to the project by personnel of the Rocky Mountain District and the Geophysics Division. Individual acknowledgements to these people are made at the end of the paper. BASIS FOR THE PROJECT The project was based on the idea of W. S. Burbank (1947, p. 444) that commercial deposits of base metals might occur in Paleozoic sediments beneath hydrothermally altered volcanic rocks in the Southern Bonanza mining district, Colorado. Paleozoic sedimentary rocks, including the favorable Leadville limestone, are exposed three miles south of the altered area, and reason exists to believe that they might underlie it within a reasonable depth. Alteration of pre-mineral volcanic rocks has been used successfully as a guide to concealed orebodies in the Main Tintic and East Tin tic mining districts, Utah (Bill-ingsley, 1933, p. 120-122; Lovering et al, 1949; Howd, 1957, p. 124-134; Cook, 1957, p. 73) and could be a useful guide here. GENERAL GEOLOGY AND STRUCTURE The Northern and Southern Bonanza mining districts are northwest of the San Luis Valley in southern Colorado, just within the northeastern edge of the San Juan volcanic province. The districts are1ocated on the southern extension of the Sawatch uplift, a prorninent northwest-trending structural high. The highly productive mining camp. of Leadville, Gilman and Aspen are on the northeastern and northwestern flanks of this uplift where Paleozoic limestones have

Jan 1, 1961

By T A. J Hopper, B J. Birt, K K. Trofimczyk

Nuclear magnetic resonance (NMR) has been utilised in the oil and gas industry for over 60 years. The technology was recently identified as having potential value in iron ore, where latent bound moisture may affect ore handling even after dewatering and extraction. The first step in introducing this technology to iron ore involved laboratory tests on drill core samples. These results established the parameters for a downhole borehole magnetic resonance (BMR) tool for iron-rich environments, which was subsequently developed. A major challenge involved shrinking what is a very large tool in the oil industry to a slimhole, lightweight, 1-man deployable mining tool.Of primary concern was the ability to measure the very fast transverse relaxation times (T2s) seen in the lab results on iron ore samples. Iron creates local field gradients that significantly decrease the T2 times. As a result, the BMR tool had to be able to measure T2s in the range of hundreds of microseconds, a level not required in clastic sedimentary formations. The choice of T2 cut-offs in iron ore is critical to successfully separating the free and bound fluids. The industry has typically focused on T2 cut-offs in clastics and carbonates, but not in systems with high iron content. Using core analysis results (poro-perm and NMR) we were able to verify the BMR response. The T2 cut-offs were determined from NMR core analysis and then applied to the logs so as to provide a continuous, calibrated permeability log.Field results that highlight the challenge involved in logging in iron-rich environments are presented, as well as some minimum requirements for a successful BMR log. Examples from boreholes in an active iron ore mine in the Pilbara iron ore province in Western Australia are presented, as well as explanations for how NMR data can be combined with bulk density logs to provide a continuous dry weight density log based on the original density-porosity equation from Alger et al (1963).CITATION:Hopper, T A J, Trofimczyk, K K and Birt, B J, 2017. Development of a slimhole downhole nuclear magnetic resonance tool for iron ore – some applications and limitations, in Proceedings Iron Ore 2017, pp 473–480 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By R. Stenne

This paper presents the trends in deep foundations in Europe, both in terms of design and construction. Eurocode 7 which is a design code for geotechnical engineering will be introduced in the European Union member countries, and will oblige geotechnical engineers to abandon traditional methods based on a global factor and adopt a new approach based on partial factors of safety. Execution codes (for construction of foundations and other geotechnical processes) are currently being introduced without problems. Ever more demanding environmental constraints push foundation contractors to adapt old techniques and develop new ones to comply with new regulations.

Jan 1, 2000

By J. D. Findlay

The demands on development in London in recent years has led to the increasing use of top down construction methods in which there is a requirement to place steel columns to high tolerances into large diameter bored piles with deep cut-offs. A number of different proposals for the sequence of construction are being suggested. The tolerances requires for the steel columns are becoming increasingly stringent. This review examines a number of basic construction proposals and comments on the problems and solutions used by foundation contractors to provide the required foundations.

Jan 1, 1989

A laboratory size solvent extraction apparatus has been constructed, which incorp- orates three stages of countercurrent extraction, followed by two stages of counter- current stripping. The model uses a gravity flow system from one stage to another and air lift pumps to recirculate organic and aqueous phases. A novel pump/mixer system is used to transfer solutions from the mixer compartments to the settler compartments. The model has proven valuable in the teaching of solvent extraction principles.

Jan 1, 1999

By R. D. Yancich

A case study of longwall mining surface subsidence was performed at a mine in Southwestern Pennsylvania. The mine operated in the Pittsburgh coal seam which averaged 70-72 inches with 6-8 inches draw slate in the longwall location. The average overburden depth ranged from 625 8eet to 660 feet. Three adjacent longwall panels were studied and classified as Panel 1, Panel 2, and Panel 3. The following is information on each and can be seen on the General Mine Map (Fig. 1).

Jan 1, 1984

By Andreas Brandner

"At the beginning of 2007 the Austrian contractor PORR was awarded with remediation works for a 48-km long part of the railway line from Campina to Predeal – part of the Trans European main Corridors TEN-T priority line 22 Bucurest – Brasov, connecting the southeast European countries with the heart of Europe.Due to partly new realignment and change of regular sections as well as protection against rockfall and slope slide a huge bunch of slope stabilization works became necessary, which were awarded to the contractor PORR and their designer IB-Brandner.Following the studies of the tender documents for the planned protection measures responsible managers of PORR decided to propose an alternative protection design by IB- Brandner. Changing the original design a more flexible and environmentally compatible solution consisting of high performance net, soil nailing and rockfall protection systems (fences) was elaborated and adapted to local needs. During design process, several critical areas were identified and additionally taken into account.In the paper examples of the design and erection process show how difficulties in implementation starting with the presentation of the idea continuing to the realization on site were managed and a technically more sophisticated and commercially competitive solution could be delivered to the customer Romanian Railway – case study.The European Commission awarded – following an election process in which all citizens of the EU could join - the remediation project Railway line Campina – Predeal in Romania as the environmentally best EU co-financed infrastructure project. GENERAL PROJECT EVALUATIONDue to original design slope stabilization should be done by concrete slabs fixed with prestressed anchors and shotcrete cover.The area to be secured was limited to a 12-meter strip left and right from the railway track without reference to nature and local needs. Discussions with the client and his designer and rising awareness for the hazards to address took several months. Site visits in Austria to provide insight in the problems of dealing with natural hazards helped to convince the client of the needs and our alternative design."

Jan 1, 2017

The addition of cement to underground backfill at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited, Broken Hill commenced in 1967. A deterioration in metallurgical performance at each concentrator occurred as a result, with increased loss of lead and zinc to residues. Investigations to determine the reasons for this problem and methods to counteract it have been undertaken. This paper outlines the effects of cement on lead-zinc beneficiation at Broken Hill and presents an interim report on attempts to overcome the metallurgical deterioration.

Jan 1, 1971

On the basis of field observation, four principal styles of hydraulic breccia are recognised, and their characteristic features noted. In practice, hybrid styles are most commonly encountered. Numerous examples will be illustrated during the oral presentation, and the potential for definition of a formative environment is emphasised. In one example presented, it is suggested that more than 50 episodes of hydraulic fracturing can be recognised. In all cases at least sane useful conclusions can be drawn in the context of modeling for drill targets.

Jan 1, 1987

By N Coplin

Australian Coal Association Research Program (ACARP) project C25073 was proposed by industry stakeholders seeking a potential solution that improves underground air quality and reduces operational costs associated with technology used to control diesel particulate emissions in the underground coal mining environment.The need to protect workers from diesel particulate matter (DPM) has lead the underground coal mining industry to install disposable filter systems on their vehicles. While the disposable filters are efficient at removing significant amounts of DPM, the following major issues have arisen:- high cost of operations; disposable filters cost $A250–300 each and need to be changed at least once per shift resulting in an estimated cost of up to $A164 M/a, in filters alone, to the NSW underground coal mining industry- improper installation, damaged seals and lack of installing a new filter when the old filter is removed; workers are still being exposed to excessive amounts of DPM.The ACARP project successfully demonstrated significant DPM emissions reduction comparable to the incumbent disposable technology on a proof-of-concept wall-flow diesel particulate filter (DPF) system, as well as satisfactory system robustness when assessed using an industry representative test cycle representing operations of a load haul dump (LHD) vehicle typical of that used by the Australian underground coal industry. It was noted in testing that the technology increased modal NO2 formation, but was compliant over typical operational duty cycles.One of the key benefits with the use of a wall-flow DPF system is its tamper-proof design, mitigating the risk of operating unfiltered diesel plant in poorly ventilated areas. Elimination of the need for continual replacement of disposable filters provides significant operational savings estimated to be up to 80 per cent of the incumbent technology.In addition to the above, the project also delivered a number of significant contributions to the knowledgebase of the Australian and international coal industry with regard to the characterisation of operations and control of emissions.CITATION:Coplin, N, 2017. Wall-flow type diesel particulate filter system to replace existing wet element filter systems used in typical LHDs in underground coal operations, in Proceedings Australian Mine Vent Conference 2017, pp 119–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By T. A. Kirk

"The Linatex Dewatering System is a compact, low capital and maintenance cost matched set of processing equipment suitable for solids recovery, dewatering and desliming sand-like materials in the range 3/8"" to 325 mesh ( 1). Since its introduction to North America in the early 1970s, various elements of the system have been successfully installed in a variety of applic11tions both in Canada and the U.S.A. Examples are chosen from the coal, fine aggregates, iron ore and industrial minerals industries.II. Elements of the Linatex Solids Recovery System(A) The Linatex Separator (See Fig.I)The Linatex Separator, which is the heart of the system, is a specialized type of hydrocyclone designed to give a self regulating rope discharge product. It has the familiar cyclone geometry of cylindrical and conical section, tangential inlet, apex and vortex finder. The apex is enclosed in a unique patented automatic underflow regulator consisting of a collapsible rubber sleeve, and the overflow line is a siphon-leg, with a controlled air bleed valve. The siphon leg is adjusted so as to balance the internal negative pressure acting as a closing force on the underflow regulator against the mass of slurry pressing down on it from the cone section of the Separator. With correct adjustment the underflow regulator will close drip-tight on a water only feed. As solids accumulate in the apex of the cone the weight of solids counterbalances the vacuum and cat1ses the underflow regulator to open and discharge classified material at a controlled density."

Jan 1, 1978

By Ben Bradshaw

Context ? Community engagement has become an increasingly significant and challenging part of mineral exploration and mine development; indeed, opposition from communities proximate to a proposed mine site has been known to derail technologically- and financially-sound projects. ? These cases suggest that mining firms need to better understand how to engage constructively with local communities in the pursuit of their claims. ? While a range of publications exist promoting various community engagement strategies, these recommendations, when viewed as a whole, are disjointed and largely untested in real development contexts. Aims of Presentation 1. Synthesize industry, NGO, government and academic publications focused on community engagement best practice in order to highlight those practices that are most commonly recommended. 2. Review the (Canadian) mining industry?s experience with some of these strategies based on existing case material in order to identify the extent to which commonly prescribed strategies are used and validated in practice.

May 1, 2010

The mechanization of the coal industry in New South Wales involved the introduction of large face and transport machines. The trend is towards still higher capacity units with .greater horsepower and it became apparent that a potential risk of damage to the hearing of workmen existed. In order to assess whether the sound levels were SUfficiently high to impair the hearing of workmen a sound level survey of all major operations in the industry was carried out by the Mining Engineering Division of the Joint Coal Board.The results indicated ·that the operations could be classified into three categories of risk, probably hazardous, of doubtful hazard due to the intermittency of the operations, and of low hazard.Legislation has subsequently been enacted requiring the wearing of hearing preservation aids in some of the probable risk operations.

Jan 1, 1974

The history of the industry which recovers rutile and zircon from the heavy mineral beach sand deposits of Eastern Australia began with the initial discovery of zircon in 1895. Whereas a large number of small companies operated during the rutile boom of 1955-57, the industry is now controlled by a few large groups.Mining is mainly by suction dredging. Metallurgical practice is a two-stage process in which a bulk concentrate of heavy minerals, recovered by gravity methods, is separated into its constituent minerals by processes based mainly on surface, electrical, and magnetic properties.Various separating devices using these principles have been developed in the industry and combined in various ways in the operating plants.There is scope for future metallurgical developments.INTRODUCTIONThe existence of deposits of heavy minerals ("black sands") on the northern coast of New South Wales has been known for at least 90 years. The earliest metallurgical operations aimed at the recovery of gold, platinum, tin and monazite. Mainly because of the low grade of these deposits with respect to these minerals, but also due to metallurgical difficulties, such operations were abandoned by about 1895 (Whitworth, 1959). The presence of zircon was recorded quite early (Carne, 1895) but Raggatt (1925) appears to have been the first to report the presence of rutile.The economic exploitation of the deposits was initiated in 1928 when D. H. Newland, State Geologist of New York, made an examination on behalf of The Titanium Alloy Manufacturing Company of America. Developments were then delayed by the world-wide depression, and the first commercial separation of the heavy minerals was made at Byron Bay in 1934 by Zircon Rutile Ltd. using a froth...

Jan 1, 1963

By C Vuillier, A Roshdieh

Water is the main medium for removing impurities from iron ore during wet processing to achieve a higher quality product. However, there is a substantial increase in freshwater consumption due to an increase in demand from the following two factors: in the past 55 years the world population has doubled from 3 to 7.5 billion and crude steel production has increased five times from approximately 350 to 1662 Mt/a (IISI, 2008). Furthermore, social development in developing countries exacerbates water consumption making freshwater an increasingly valuable resource with an average distribution of 70 per cent for agriculture, 20 per cent for industry and only ten per cent for domestic consumption (Hourtolle, 2005; OECD, 2009). Rapidly changing regulations over the access and preservation of water across the world indicates the growing importance of this issue, so the mining industry must adapt to this continual change and must be committed to increasing the efficiency of water usage.Tailings dams receive most of the water used by the process plant. In arid regions where evaporation is high and availability of water low or non-existent, technical solutions other than the conventional tailings dam, such as thickened and/or filtered tailings, exist to optimise the recovery of water and reduce the need for external water consumption. However, these solutions present additional challenges, such as energy consumption and transportation from the process plant to the ultimate storage area.This paper considers a range of alternatives covering thickening and filtering, transportation and storage, water return, closure and rehabilitation. Mining projects in the future will be more affected by the rising cost in water and tighter regulations in accessing water and energy. Good tailings management can contribute significantly to reducing the dependence on these two key commodities (water and electricity), improving the resilience of iron ore projects especially in arid regions and areas with high competition for water.CITATION:Vuillier, C and A Roshdieh, A, 2017. Minimising the water loss associated with mine tailings disposal, in Proceedings Iron Ore 2017, pp 245–250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Forrest T. Moyer

Injury experience at coal mines and mechanical-cleaning plants (excluding officeworkers ) in 1967 was 222 fatal and 10,115 nonfatal disabling work injuries during an exposure time of 241.8 million man-hours. These injuries occurred at a frequency rate of 42-75 per million man-hours worked; the severity rate was 7,699 days lost or charged per million man-hours. Each of these general measures of injury experience was lower than similar data recorded for 1966. Employment at 6,885 coal mines and 569 mechanical-cleaning plants, excluding officeworkers, averaged 139,312 men in 1967. The average number of days worked was 220. Coal production totaled 560.8 million short tons, at rates of 2.32 tons per man-hour and 18.32 tons per man-day. A total of 2,779 onsite officeworkers at coal mines and mechanical- cleaning plants worked 5.2 million man-hours in 1967 without a disabling work injury.

Jan 1, 1972

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

By W. A. Wood, H. M. Bendler

Cylindrical fatigue specimens of OFHC* copper were subjected to alternating torsion while under axial tension. The superimposed tension strongly influenced the fatigue life of the specimens as well as causing characteristic changes in the structure of the fissures that form and develop throughout the life of the specimen. A further effect of the superimposed tension is a continuous extension of the specimen throughout its life in a manner formally similar to creep at elevated temperatures. RECENTLY, studies of the structural changes leading to fracture of metals by fatigue have been made by a technique which reveals, in section, the lattice distortion arising from slip movements inside the metal and the disturbances built up by these slip movements at the metal surface.1'2 According to this approach, fatigue develops as follows: a) fine slip movements concentrate in bands, producing little strain-hardening and thus permitting abnormal totals of plastic strain before fracture and, therefore, abnormal amounts of lattice distortion along each slip band; b) both forward and backward slip movements occur in each band which, according to their distribution across the band, may build up surface disturbances that include sharp notches; c) these notches early in the life of a specimen penetrate the distorted slip zones and transform them into deep, fine fissures; d) the fissures on continued cycling locally saturate the metal and cause local collapse in the form of a microcrack. Thus, the significant consequence of fatigue or cyclic

Jan 1, 1962