Search Documents

A rotating disc geometry was used to provide a uniformly accessible surface for a kinetic study of the cementation of cadmium, lead, and silver from dilute aqueous solutions. This work is an extension of studies carried out on the Cu-Zn and Cu-Fe systems for which the reaction rate was found to be completely solution phase mass transfer controlled.When the amount of material deposited was greater than 0·2 to 0·4 mg/cm2 there was an apparent enhancement in rate which is attributed to the formation of a roughened deposit. This same phenomenon was observed in the Cu-Zn and Cu-Fe systems. Again, the rate of reaction of each system investigated was found to be solution-phase mass transfer controlled.

Jan 1, 1971

IN dealing with this subject the intention is not to write a detailed description of the various methods in vogue on the Kalgoorlie field, but rather to give a brief outline of three of the methods which are most universally in force, and from which, ultimately, a few comparisons may be drawn. The three methods which the writer proposes embodying in this article are known as "The Rill," "The Flatback," and "The Shrinkage." For comparative purposes each method will be applied to a block of ore 500 feet in length, and opened up by levels 200 feet apart."The Rin" System. It is necessary in this system, for facilitating mullocking, to make connections between levels by rising and winzing at about every 100 feet or 150 feet along the orebody. After the leading stope is beaten off for the full length ofthe drive, the level is timbered. Single stulls are put in up to a width of fourteen feet. If the span is too great for stulls, set timbers or saddleback stuUs are used. Stulls are lagged over with 4-in gimlet poles, and wooden chutes are built at intervals of 50-feet. Ore passes are cribbed up through the filling directly above each chute, and are constructed of 7-in. round timber or 9 in x 3 in square timber, the passes measuring 4 ft x 4 ft in the clear.Occasionally a double pass may be carried up, one side serving as a travelling way. Stoping is commenced off the winzes, and rills are gradually formed, one on either end of each winze. The rills are generally at an angle of 37° off the horizontal, this allowing for the boring...

Jan 1, 1909

By Erik Sherer

Indonesia is poised to become a major player in the Pacific Rim thermal coal markets. Although the colonial Dutch developed numerous coal mines in the late 1800's for steamship bunkers and domestic fuel, Indonesia's coal industry has only recently begun to actively participate in the growing global marketplace. This export coal is primarily the result of the commercial development of coal mines in eastern Kalimantan by foreign contractors. From virtually no coal exports in the late 1980?s, Indonesia's coal industry has increased its exports to approximately 15 million metric tons (Mmt) in 1992. In 1992, Indonesia was the world?s sixth largest exporter of steam coal, By the year 2000, Indonesia projects that it will supply approximately 25 percent of the seaborne thermal coal requirements of the Pacific Rim countries. Although limited quantities of this coal may enter the European and U.S. markets, high qualities, low production casts, and favorable transportation rates will make Indonesian coals very competitive in the rapidly growing Pacific Rim markets. This study examines the Indonesian coal mining industry and compares it to the U.S. coal mining industry. This report is the sixth in a series of coal exporting country studies requested by the House Appropriations Committee. Previous studies examined the Colombian, Canadian, Australian, South African, Polish, and Venezuelan coal industries.

Jan 1, 1994

By J. R. P. Aguirre

Minerales Monclova, S.A. de C.V. (MIMOSA) is owned by Grupo Acerero Del Norte (GAN). This company has 4 underground coal mines and 1 open pit to feed it?s steelmaking facilities located in the city of Monclova in the North of México in the state of Coahuila. The current underground mines are Mine 3, 5, 6 and 7 and the future projects are Mines 8 and 9. In the last years Mines 2 and 4 have been closed because they finished their coal resources. The remaining mines have bigger production and developments requirements in order to accomplish the goals of the company. The mines have been working in deeper and gassier areas. These conditions have required improvements in the ventilation design and methane control systems for all the mines. In some cases the ventilation of some of the MIMOSA?S mines has been increased 80%, and besides this, an intensive methane drainage program has been applied using horizontal in-seam boreholes and gob wells. The short-term ventilation plan includes the construction of 3 new vertical shafts with 5 and 6 meters diameter for Mines 5, 6 and 7 and the purchasing of bigger new main and backup fans for each one of these mines. One of these vertical shafts and the purchasing of the first 2 fans is already in process. This paper will explain the evolution and results of the ventilation and methane drainage systems in MIMOSA and the ventilation planning for the future years.

Jan 1, 2009

Water rights and availability are extremely contentious issues in many mining regions around the world, in some instances leading to violent confrontation. This situation has the potential to only get worse because competition for 'scarce' water resources will increase with population growth. In this environment the dilemma facing the mining industry is how to generate confidence in developing a responsible, sustainable and transparent water management strategy that is recognised as such by all stakeholders. Whilst the water needs of the mining industry are minor compared to those of agriculture, an operating mine requires a relatively large quantity of water on a daily basis to carry out operations. Another contentious aspects of new mine development is the debate between all stakeholders on the amount and quality of water that a mine is able to discharge into the environment should this be required. There are a multitude of water resources available to the mining industry for operational needs however much of this water is saline and over the last two decades there has been a continual decline in water quality (ie salinity has increased). In today's world there are enormous internal and external pressures to reduce water consumption at a mine and/or alternatively use water not considered a resource by the local community (ie sewage, saline or salt water, desalinated water). Strategies to meet these objectives can be achieved by implementing good water management practices, by recycling process water, reducing water losses by evaporation and seepage (ie by increasing and improving dewatering practices) and employing new technologies such as dry stacking and dry processing. Recycled water, acid mine drainage water and water collected in the mining area have the potential to impact mineral processing performance, unless they are treated, because of the build up of mineral salts and decomposed chemical products in these types of waters. Besides this the regulatory requirements of any water discharged from a mine site (quantity and quality) have also become more stringent. For these reasons there is now some form of water treatment practiced at most mining operations around the world. This paper provides an overview of water stewardship undertaken in the mining industry over the last two decades and provides examples of water treatment practices that have recently been installed at mining operations that may be of interest to the reader.

Sep 13, 2010

The only economically significant deposit of dolomite in New Zealand is at Mount Burnett, in north-west Nelson. The dolomite, associated with marbles and schists, is complexly deformed, and is of Paleozoic age.A very large quantity is present, although the recoverable amount is to some extent limited by the difficult terrain.Physically the quality of the dolomite is excellent. It is a tough, durable, fine grained rock. Chemically it is a little more variable. The range and frequency o~ the more important impurities are illustrated by hlstograms, as is the "dolomite factor"-a measure of the amount of the mineral dolomite in the rock. lbe dolomite factor averages 84 per cent, the remainder of the rock consisting largely of calcite. Quarrying, milling, production, and uses are described. In 1966 production reached 13,250 tons.

Jan 1, 1969

By Alun J. Davies

This paper describes a design-build project for the construction of a tanker wharf for 150,000 dwt vessels. The tankers deliver oil from offshore oil fields to a Transshipment terminal on the south coast of Newfoundland. The project described is an expansion to a previously constructed facility, adding an additional berth. The first berth was designed conventionally as concrete structures supported on groups of independent, single piles. The second berth was awarded to Peter Kiewit Sons' Co. Ltd. based on an alternate design which utilized a "jacket" concept whereby prefabricated steel frames are placed on the seabed and serve as permanent templates and also give lateral support to the piles, thereby increasing their load capacity. This led to economies and time savings. Discussed herein is the design process and the field installation, covering the jackets, driven pipe piles, and the rock anchors.

Jan 1, 2000

By Madgwick J. C

The monosaccharides glucose, galactose and arabinose, and the polyols glycerol and mannitol (0.1 Ufo WIV) supported pure and mixed culture heterotrophic bacterial manganese leaching of solid pyrolusite (MnO2, 2% W/V) to yield 14-38 mg/litre manganous ion in 3 days from a simple mineral salts media at 30°C. Supplementation of pure bacterial isolates growing on glucose with soluble intracellular photosynthate from freshwater algae (0.07 g/l carbohydrate) and marine algae (0.11 g/l) led to an improvement in Mn++ yields of 24 and 100 per cent respectively. Extracellular products of the freshwater algae (0.3 g/l carbohydrate) boosted recoveries by 57 per cent.

Jan 1, 1982

By R. Barbaroux, B. Dubreuil, D. Lemieux, K. Nasrallah, G. Garcia Curiel

"As conventional, base or precious metal ores are being depleted worldwide, the mining industry is being faced with an increasing exploitation of arsenical sulfidic ores. Enargite is a common example. The downstream processing of these ores poses several problems ranging from high smelter penalties to finding economical and environmentally acceptable means of disposing of the arsenic. Several hydrometallurgical processes have been proposed for extracting arsenic from enargite concentrates, notably using alkaline sulphide leaching (ASL). However, few alternatives exist for removing the arsenic from solution and stabilizing it in an approach that is both economical and environmentally acceptable.Dundee Sustainable Technologies (“DST”) has developed a technology for the sequestration of arsenic by vitrification. Originally optimized to cost-effectively stabilize arsenic trioxide (As2O3), DST has shown that vitrification could be successfully extended to the stabilization of other arsenical products, such as calcium arsenate (Ca3(AsO4)2) and sodium arsenate (Na3AsO4). In this paper, the vitrification of arsenic in the context of an enargite leaching was newly explored and demonstrated successfully.Two processing routes are being proposed by DST for the removal of arsenic from enargite concentrates and their stabilization by vitrification. In one route, arsenic is extracted by ASL and is then precipitated under atmospheric conditions and with minimal use of reagents and time. The resulting precipitate is an unstable hydrated ferric arsenate (FeAsO4•2H2O) that is then vitrified in a non-dilutive method, significantly increasing the stability of arsenic and meeting the TCLP guideline. Unlike is required for scorodite, stabilization was successfully achieved without concern for the crystallinity of the precipitate."

Jan 1, 2017

By K. Lundholm, M. Andersson, L. Nevatalo, Å. Holmström, L. Hedström

"Several copper deposits have the arsenic bearing minerals enargite (Cu3AsS4) and tennantite (Cu12As4S12). Since this mineral contain both arsenic and copper, it is not possible to remove the arsenic by selective flotation. Partial roasting is a method to clean the concentrate from arsenic and thereby produce a suitable raw material for the copper smelter. Also mercury is commonly found in copper bearing minerals. In the partial roasting process both arsenic and mercury are volatilized, while part of the sulphur is used as energy during the roasting. This gives a calcine suitable as feed to a smelter, much like an ordinary copper concentrate. A typical analysis of calcine would be: S content 18–22%, As content below 0.3%, Cu content – not affected, grain size – not affected. However, if the concentrate contains mercury, the mercury will be volatilized during the roasting process. This will lead to very high mercury contents in the subsequent process of sulphuric acid, unless the SO2-rich process gas is pre-treated by the Boliden/Norzink process that recovers mercury as calomel, Hg2Cl2. The volatilized arsenic in the gas phase can be recovered either by dry or wet methods. However, one problem is that arsenic also contaminates the fine grained calcine dust that is captured downstream in the gas cleaning system. The calcine dust contains valuable metals such as copper, gold and silver that needs to be separated from the arsenic. The ultimate aim is to stabilize the recovered arsenic as a compound with minimum impact on the environment and recover the valuable metals. By using wet recovery methods it is possible to selectively precipitate copper, gold and silver as sulphides while arsenic is kept dissolved in the liquid. The precipitated metal sulphides can be mixed with the calcine and sent to the copper smelter. The dissolved arsenic is sent to effluent treatment and is further treated in Outotec ferric arsenate precipitation process, where arsenic is precipitated as the stable compound basic ferric arsenate, formula FeAsO4·xFe(OH)3. All concentrates containing arsenic are unique and the process design of a roaster plant must be based on relevant process data. The process data is collected during tests in lab scale and pilot scale, where the influence of critical process parameters on the quality of calcine is studied. The ability to run tests both in lab scale and pilot scale is crucial to the development of the correct roasting process. Outotec is well equipped for this."

Jan 1, 2014

By Shane Baker

Cementation Foundations Skanska Ltd encountered many significant challenges in designing and constructing the foundations for the LNG (Liquefied Natural Gas) tanks and associated structures at the Isle of Grain, Kent, UK. With LNG cargo ship levels fixed by the adjacent English Channel, the platform could not exceed critical thickness in order to achieve final grade level, so a safe and efficient working platform for construction equipment on extremely poor alluvial soils was designed and installed. The detailed pile design also required particular analysis of the pile group behaviour and considered seismic load cases not usually associated with UK pile design. Continuous flight auger (CFA) piles were the chosen foundation solution and design was verified through preliminary and working pile tests both axially and horizontally. Contaminated land and existing foundations from a previous oil terminal meant that removal of spoil was extremely costly so specific measures were taken to minimise the off-site disposal. The management of a package of general Civil Engineering in addition to the piling scope, coupled with an unrelenting production program has forced a raising of the bar for this foundation technique.

Jan 1, 2006

By Gordon Chen

The Block 37 Chicago Transit Authority (CTA) Tunnel Construction Project was originally designed by STV to connect Blue Line subway in North Dearborn Street and Red Line subway in State Street in the downtown Chicago Area. The project was proposed using tunnel mining techniques combined with steel pipe jacking and fiber glass rebar soil reinforcement. Weidlinger Associates, Inc. (WAI) and Kiewit Construction Company proposed an alternate design using open cut construction technology. WAI designed a complex temporary excavation support system using Soldier Pile Tremie Concrete (SPTC) walls and Soldier Pile Lagging walls supported by cross lot/corner bracing elements. Below the top of the existing tunnel, a top-down construction technique was utilized. A steel temporary traffic decking system at top of the excavation site served as the daily street traffic function as well as the first level of bracing for the support of excavation. The project encountered great challenges of soft clay conditions in downtown Chicago, numerous existing utilities in the excavation site and the requirements of protection for a number of historical buildings nearby as well as the protection of the city streets. The construction was successfully completed at both State Street/Washington Street and Dearborn Street/Randolph Street. The monitoring system showed that ground movement and adjacent building settlement was kept to a minimum during construction.

Jan 1, 2009

By S. O. Bada

Coal samples taken from the No. 2 Seam and No. 4 Seam in a South African colliery were tested in a rotary triboelectrostatic separator. The two-stage triboelectrostatic separation results using the -177 µm size fraction reduced No. 2 Seam coal containing about 30.4 per cent ash to a clean product of 8.9 per cent and 13.1 per cent ash with combustible recoveries of 9.6 per cent and 30.7 per cent respectively. The same separation approach on No. 4 seam feed coal, which contained 36 per cent ash, produced a clean coal product with 10.8 per cent ash at a combustible recovery of 6.0 per cent. Petrographic tests show a significant improvement in the vitrinite content and a reduction in visible minerals encountered when using the triboelectrostatic separator, with about 53 per cent vitrinite reporting to the clean fraction for No. 2 Seam compared to the feed content of 21 per cent, and a 54 per cent vitrinite in the clean No. 4 Seam from a feed content of 21 per cent. Significant sulphur reductions were also observed after separation in both coal samples, with a better separation in the second-stage coal products.

Jan 1, 2012

By Joseph L. Young, Richard A. Bohling

To keep Homestake's Bulldog Mountain silver and lead mining and milling operation in southwestern Colorado workable, natural ground water and decant water from the mine's sand backfilling operation must be continually pumped from the workings. Left untreated, this water exceeds maximum allowable levels for various contaminants that may be discharged to the environment. To comply with regulations, a National Pollutant Discharge Elimination System (NPDES) permit was obtained and a mine water treatment plant for heavy metals removal was constructed in 1977. Due to equipment capacity and operational problems, and the lack of on-site technical personnel and analytic equipment, the first water treatment plant could not consistently meet permit limits. In 1979, Homestake entered into a consent decree with EPA and the Colorado Department of Health, calling for the construction of a water treatment facility to meet NPDES permit limits. Initial construction began in the spring of 1980 and the plant now produces effluent acceptable for discharge.

Jan 12, 1981

By A. R. Barnes, A. F. Newall

Keywords: Pyrometallurgy, furnace, smelting, spinel, PGM, phase diagrams As Merensky reef ores are replaced by UG2 ores, chromium levels in PGM smelting furnace feeds have steadily increased. Increased chromium levels lead to operating problems. Attempts to increase the chromium solubility in the slag by a variety of techniques create other difficulties. The authors have developed a technique for removal of the chromium spinel interface along with the matte for subsequent separation outside the smelting furnace by utilising differential solidification in the ladle. The process has been patented internationally with support from the Innovation Fund.

Jan 1, 2006

Large scale fluid extraction from the Latrobe Group in the Gippsland Basin is occurring as a result of offshore petroleum production and coal mine dewatering in the Latrobe Valley. Groundwater extraction in the Latrobe Valley exceeds recharge and is causing an expanding area of declining hydraulic head in the Latrobe Group, and regional land subsidence which is well documented. Recently the government water sector completed the installation of a network of Latrobe Group monitoring bores in the remainder of the onshore part of the Gippsland Basin. The bores situated along the coastal area show a steady decline in hydraulic head of about 1 m/year which can be attributed mainly to petroleum production.

Jan 1, 1992

This Institute, by nature of its charter, draws on various persons in the mining and metallurgical world of Australasia for its President from year to year, and consequently when the presidential address is given by one of these people the topic. which they generally select is a topic to which they are accustomed and on which they are able to speak with authority.As most of you know, my prime object in life has been concerned with steelmaking, so tonight you can steel yourself to the thought that you are going to be spoken to about steelmaking.Even if that were not the case, and were I not particularly interested in steelmaking, I think it would be appropriate to look at steelmaking in a broad sense on a basis of pure metallurgical interest, because the steel industry is going through as big a revolution today as it went through something over one hundred years ago when Bessemer made a theory become a fact.Bessemer, and as the Americans prefer to think Kelly, separately conceived the idea of blowing cold air through molten pig iron, and, contrary to the then general belief, this did not result in cooling of the metal but succeeded rather in heating it, and in burning out of the rather crude pig iron the impurities which prevented it from becoming a ductile metal.For many years before this, steel had been made in a very small painstaking way by what was known as the crucible process. Benjamin Huntsman is credited with having developed the crucible steel making process to a stage where it could make a reliable and trustworthy product, but he...

Jan 1, 1961

By Eleanor Sonley

In October 2000, temporary seismographic stations were installed above the Trail Mountain Mine, Emery County, Utah, USA to supplement a regional network. Over seven months, 1826 mining-induced seismic events were recorded with a magnitude range of M 0 to M 2.2 (Arabasz et al., 2002, 2005). Routine event locations for this dataset cluster around the longwall mining activity during the recording interval. However, applying a double difference relocation technique to the routine locations significantly improves the correlation between mining activity and event location. The resulting relocations depend greatly on station distribution and the number of arrival time picks. We use this dense temporary array to assess station distribution requirements for applying the double difference technique at other mines by systematically removing data from available stations, thus simulating sparser networks. The insight gained using the Trail Mountain dataset is used to develop a metric for assessing the usefulness of above-mine networks and to develop a tool for expanding seismic network coverage. To verify the appropriateness of these tools for wider application, we examine data from two additional mines located in the western United States. Improving the relative locations of mining-induced seismic events highlights the association of these events with active portions of the mine. Clusters, regions of quiescence and relative timing of events can be used by mine operators to assess hazard, optimize production, and evaluate performance of mine plans. The lessons learned from this study may be used in future network design to improve accuracy of event locations at other mines.

Jan 1, 2009

By Hennessy F. L

IntroductionEvolution of the Present SmelterRoastingFiringHearth SlopeDust HandlingFurnace DetailsSmeltingFurnaceFeed DeliveryPulverised Coal FiringWaste Heat BoilersDust HandlingAir PreheaterReverberatory Slag DisposalConvertingVesselsAir SupplyMatte TappingConverter Slag HandlingPurchased Ore PlantINTRODUCTIONSmelting in blast furnaces commenced at Mount Morgan in 1906, when copper, which interfered with gold recovery by chlorination, became an asset. After various changes in blast furnace practice, reverberatory smelting com...

Jan 1, 1952

By Brendan Henry

The Canada Line is a 19km long automated light rapid transit system with 16 stations in Vancouver, BC, Canada. The Concession was awarded to InTransitBC to design, build, partially finance, operate, and maintain the system for 35 years. The project must be complete by November 2009 to be ready for the 2010 Winter Olympics to be held in Vancouver and Whistler, BC. The bored tunnel section consists of 2.45 km of twin bored tunnel and 3 stations. The station work is limited to the excavations and temporary support necessary to facilitate the bored tunnel works. A joint venture between SNC-Lavalin Constructors Pacific and SELI (SSJV) has recently completed the design and construction of this section. Work for the bored tunnel commenced in November 2005 with shoring and excavation works for the tunnelling operations pit that will become Olympic Village Station and will be completed in the spring of 2008. The tunnels were driven with a 6m diameter Earth Pressure Balance Tunnel Boring Machine (EPBM) and lined with 250mm thick, 5.3m diameter precast concrete segments. Seven hundred and fifty meters of each tunnel were driven through glacial and interglacial deposits of sand, silt, and clay with granitic boulders. The paper discusses the challenges faced in negotiating these soils which contained unforeseen geological conditions. These conditions were overcome by developing a systematic approach to Risk Management that included thorough risk assessments, regular risk management meetings with the participation of two of the world?s leading EPBM experts, Professor Eisenstein and Professor Kovári, and by the ability of the construction team to effectively analyze and mitigate problems.

Jan 1, 2008