Search Documents

By N. Paas

Diesel powered equipment has been operated in underground coal fir mare than 50 years. According to the Mine Safety and Health Administration (MSHA), there are approximately 3,000 diesel units operating in underground coal mines in the United States. This number is expected to reach 5,000 diesel units in 250 coal mines by the year 2000. Also, there are approximately 5,000 diesel units operating in metal/nonmetal mines such as trine, potash and salt mines: and more than 3,000 diesel units operating in Canada. This increased popularity of diesel powered equipment over trolley wire, electric trailing cable or battery powered equipment is because of improved safety, greater mobility, higher productivity and increased power of diesel equipment. The operation if diesel powered equipment is not without challenges. Diesel engines generate exhaust emissions, in particular carbon monoxide, oxides of nitrogen, sulfur dioxide, unburned hydrocarbons, and diesel particulate matter that must be maintained at safe levels. The chief method to control ambient exposure has been dilution by ventilation. A new concept to ensure continued safe ambient emissions levels from diesel equipment in underground mines is the EMISSIONS MANAGEMENT PROGRAM™. The program encompasses all factors that will influence diesel emissions. By ESTABLISHING low tailpipe emissions through technology, such as clean engines, clean fuel selection, exhaust aftertreatment devices and filtration of the exhaust gases via the Dry System ™, this program ensures that the baseline emissions are at their lowest technically feasible concentrations. The DST Dry System™ exhaust conditioner reduces DPM by over 98%, as demonstrated through laboratory research at the West Virginia University. Carbon monoxide and hydrocarbon emissions and odor are similarly reduced. MAINTAINING these low emissions requires an expanded training program for operators and mechanics, onboard feed-back devices and a maintenance program with special focus on events and faults that can alter emissions. Finally, an on-board emissions sampling system allows the mechanic to VERIFY emissions levels and help diagnose engine faults. If the tailpipe emissions fall outside an established limit for a particular equipment, corrective actions will be initiated.

Feb 24, 1997

By James Withers, Dongbo An, Jinhong Zhang

A micro-scale investigation was carried out by applying atomic force microscopy (AFM) to study in situ the adsorption of various collectors, i.e., oleic acid, octanohydroxamic acid (HA), and salicylhydroxamic acid (SHA), on bastnaesite in aqueous solutions. The obtained AFM images show that the surface morphology of bastnaesite changes greatly after it comes into contact with the solutions of the collectors, suggesting that all these collectors can effectively adsorb onto bastnaesite. Increasing temperature can facilitate the adsorption of oleic acid onto bastnaesite. Results from attenuated total reflectance–Fourier transform infrared spectrometry (ATR-FTIR) also show that all of these collectors adsorb strongly onto bastnaesite, with strong absorbance spectra being detected. The ATR-FTIR results confirm those obtained by AFM. In general, hydroxamic acid collectors (HA and SHA) adsorb onto bastnaesite mainly in the form of insoluble metal hydroxamate. This specific adsorption mechanism explains that a high selectivity with a moderate collectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite.

By James Withers, Dongbo An, Jinhong Zhang

A micro-scale investigation was carried out by applying atomic force microscopy (AFM) to study in situ the adsorption of various collectors, i.e., oleic acid, octanohydroxamic acid (HA), and salicylhydroxamic acid (SHA), on bastnaesite in aqueous solutions. The obtained AFM images show that the surface morphology of bastnaesite changes greatly after it comes into contact with the solutions of the collectors, suggesting that all these collectors can effectively adsorb onto bastnaesite. Increasing temperature can facilitate the adsorption of oleic acid onto bastnaesite. Results from attenuated total reflectance–Fourier transform infrared spectrometry (ATR-FTIR) also show that all of these collectors adsorb strongly onto bastnaesite, with strong absorbance spectra being detected. The ATR-FTIR results confirm those obtained by AFM. In general, hydroxamic acid collectors (HA and SHA) adsorb onto bastnaesite mainly in the form of insoluble metal hydroxamate. This specific adsorption mechanism explains that a high selectivity with a moderate collectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite.

By Charles Hart

In this paper it is the author's intention to show the extent and character of foreign ores now known to be available; these deposits may be in active production or held in reserve until economic conditions may make them active. He hopes to show the relation existing between these ores and the American supply, and which of the former are now producing or will in turn come into production when our better ores have been exhausted. This phase of this discussion must of necessity include some data as to the present rate of consumption and a study of the changes we may expect here and abroad in the general steel trade and its sources of supply in raw materials. It is obvious that the occurrence of coal, ore and limestone in relation to one another and the proximity of a market are the elements in control of this feature of the problem. If the foregoing situation is favorable, all the other questions may be solved, for it is clear that with proper basic conditions finance, labor and operations will fall in line. We present a short outline of the present methods of carrying on the foreign iron ore trade, believing that it is of general interest in comparison with our own highly specialized methods, and that with the exhaustion of our better ores we will be compelled to seek a part of our supply abroad. A partial list of iron ores, with incomplete analyses (Table I), is added, to give a better understanding of the general situation and explain to some extent the reason for things being as they are in the iron and steel trade of the world and to help in bringing this paper to an informing conclusion. The question of the world supply of iron ores has been a subject for study on the part of geologists and engineers for many years, and found its best results in the Eleventh International Geological Congress, appropriately held at Stockholm, Sweden, in 1910. The proceedings are published in two volumes and are undoubtedly the best records available on this subject at the date of publication. It should be borne in mind, however, that much has happened in the 20 years since these figures were assembled. There is just as much known ore at present as at that time, minus the quantity consumed, plus newly discovered reserves. The World War had great effect upon this situation; during that time explorations were greatly reduced and the settlements after the

Jan 1, 1929

Important factors in dredge design are the estimation of total head, and the determination of flow in and around suction nozzles and in pipe lines. Total head for the dredge pump is calculated from velocity, static, and friction heads. Flow into suction nozzles depends on whether hydraulic jets or mechanical cutters are used, and on nozzle shape. Design of pipe lines depends on the transportation characteristics of the pulp, skin friction, swirl, and the avoidance of cavitation. Measurement and control of flow is important.INTRODUCTIONEconomic deposits of heavy minerals along the east coast of Australia occur in frontal dunes, which are normally unconsolidated and granular, or in hind dune areas which may contain indurated seams interspersed with loose material. In working frontal dunes, dredging depths are usually shallow since values do not persist for more than a few feet below sea level. However, the controlling factor in dredging the hind dune areas is the level of the water table and suction dredges may be designed to mine to depths of 120 ft, or even more, if necessary.In previous applications of suction dredges in the industry attention was directed primarily towards production and there was only limited research on fundamental techniques. However, with lower grade deposits now forming the major ore reserves, production levels and profit margins will fall unless more efficient dredges are developed.For satisfactory design of dredges it is essential that the total head be accurately estimated and that detailed information of the principles of flow in and around suction nozzles be determined. This paper presents information gained from field experience and laboratory investigation on these aspects.

Jan 1, 1962

Interest in industrial minerals in recent years has increased to such an extent that it has taken them into the mainstream of the Australian mineral industry. Notwithstanding that time series data on the values of production, exports, and imports show that industrial minerals are overshadowed by metals and energy minerals, their contribution to the national economy is important and more significant than would seem to be indicated by the statistics. Whereas the ex mine value of metals generally includes some processing (at least to a concentrate stage), most industrial minerals are valued at little more than their extraction cost, in addition to which such costs are generally low because most industrial minerals are exploited in low-cost surface operations. Consequently, values of mine production of metals and industrial minerals are not strictly comparable in that values of mine production of metals tend to be overstated Short term growth of the industrial minerals sector is assured because of several new projects already commissioned but not yet reflected in the statistics. Longer term growth is also assured, based on various other major projects that are likely to come on stream in the early to mid 1990s.

Jan 1, 1989

By Kyoosang Yoo

The report presents the results corresponding to the analysis of a lining system for tunnels in soil and soft rock in creep-active ground. The purpose of the analysis is to evaluate the performance of a lining at each construction stage. The steps include: 1. Accurate representation of the initial undisturbed state of stress 2. Excavation, 3. Lining installation 4. Injection of mortar and its curing, and 5. Short-, medium- and long-term creep behaviour in the surrounding soil/rock. The response of a prototype tunnel is simulated using the computational finite element framework MSC.marc2008.

Jan 1, 2010

Concentrations of bright green material in the "Golden Mile" of Kalgoorlie, which carry particularly high gold values, are known locally as "green leader".This assemblage consists largely of quartz, sericitic muscovite, carbonates, and pyrite. Some of the sericitic muscovite contains vanadium, giving the rock its green colour. Vanadium oxides, including nolanite, are also present. Tellurides identified in this study are calaverite, altaite, petzite, melonite, and coloradoite. Native gold was found in most of the samples; some of the gold, at least, has been formed from the decomposition of gold tellurides.It is suggested that mineralizing solutions carrying gold and tellurium leached vanadium from the host rocks and subsequently deposited gold tellurides and vanadium-bearing minerals in the "green leader".

Jan 1, 1977

By R. Ward Stahl

This publication is a revision of Report of Investigations 5363 updated to reflect the improvement in fire protection at selected coal mines and contains suggestions on what may be considered good fire protective equipment, suggested methods of organizing the attack on fires at various locations underground, and helpful hints on testing and evaluating firefighting facilities.

Jan 1, 1968

By T. Mal

A test system was developed at the National Institute for Occupational Safety and Health's ventilation test gallery for measuring airflow using a three-axis ultrasonic anemometer. The gallery war used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data, collected at multiple sampling locations between the face and the end of the curtain, were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations and displayed as methane distributions in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within 0.6 m (2ft) of the face.

By V. Eu. Anufriev

Despite of significant cost advantages and the positive expierence roof bolting is limited up to 15-20% of all workings at the Cuzbass mines. The low level of application of the technology is the result of specific mining and geological conditions and defects of organization and technical support. When analysing mining and geological conditions of development working maintenance and geomechanical aspects the necessity of changing of technological schemes of preparation and extraction of mine sections is obvious. The prospects of large-scaled transferring from frame support to roof bolting are connected with introduction the technology of support with the help of non- expanding bolt classes including bolts with mineral filler fixation. The design of bolters with mineral filler fixation is given here. The results of testing of bolt load characteristics in artificial holes and in situ are proved the technology efficient. For increasing of drilling works efficiency it is necessary to master the production of oilless compressor and heading machines with the manipulator. For bolt dimension forecast it is recommended to use the relations of measured parameters of "dome" to roof shifts. Effective monitoring of rock pressure in the junctions is connected with the use of support of conventional bolts together with bolts of deep installation with simultaneous supporting of face ends with special mechanical sets, which compensate face length change.

Jan 1, 1996

By Y. L. Sun

The feasibility of using the ultrasonic wave attenuation method for measuring in-situ stress is examined theoretically and experimentally. The theoretical analyses show that for a given rock type the relation between stress and attenuation coefficient ratio can be approximated closely by second-order polynomials. Combining the elastic and statistical theories, the magnitude and direction of the existing principal stresses can be predicted by using the relations between stress and attenuation coefficient ratio obtained in the calibration of core specimens. Several experiments are conducted in the laboratory on two types of rock. The experimental study consists of two parts: the attenuation-coefficient measurements in core specimens under uniaxial stress and the attenuation coefficient measurements in boreholes drilled through blocks of sandstone and limestone subjected to uniaxial compressional stress. Compressional waves are used exclusively in the measurements.

Jan 1, 1989

By Samuel Frimpong

The interaction of oil sands with a ground articulating pipeline (GAP) system has been simulated with the dynamic model established in this work by combining the multi-body and soil dynamics with the Automatic Dynamic Analysis Mechanical Systems (ADAMS) software. Mathematical models governing the interaction of the GAP system with the oil sand terrain have been modeled based on the theory of multi-body and soil dynamics. These models consist of GAP track-oil sand contact model for generating the contact force between oil sands and track and load-deformation oil sand model for capturing the dynamic behavior of oil sands. A virtual prototype has been created and simulated in the ADAMS environment. The simulation result of the effect of load on oil sand deformation indicates that maximum deformation value increases non-linearly with load varying from 0 to 60t. This study provides a solid foundation for further research and the GAP technology development.

May 1, 2004

By L. A. Melis, J. W. Rowson

"Cluff Mining operates the Phase II uranium mine and mill at Cluff Lake, northern Saskatchewan. During the Phase I operation, uranium tailings were generated by acid leaching of a gravity concentrate and high-grade ore for uranium recovery. The pre-treatment gravity process, as well as the high-grade nature of the ore, led to a concentration of gold in the tailings which justified the installation of a small circuit to recover the contained gold. The operating circuit consists of tailings repulping, grinding, cyanidation, carbon-in-pulp, gold recovery, and cyanide destruction by acidification, volatilization and re-neutralization. The process is described and typical operating parameters are provided. 1.0 INTRODUCTIONCluff Mining, a Saskatchewan partnership, is owned 20 percent by Saskatchewan Mining Development Corporation (SMDC) and 80 percent by Amok Ltd./Ltee. (Amok), manager and operator of the partnership.The current operation includes the Phase II uranium mining and milling facilities, located at Cluff Lake 700 km north of Saskatoon, capable of processing 300,000 tonnes of ore to produce about 4,000,000 lbs. U308 (1500 tonnes of uranium) per year.The Phase I operation was initially established to process the very high grade ""D"" uranium orebody from 1980 to 1983. The leach tailings from the operation Phase I mill operation were found to contain elevated levels of gold. These high gold values were partially due to the gravity pre-concentration step included in the uranium recovery circuit, and to the naturally high levels of gold associated with the uranium mineralization in the ""D"" orebody."

Jan 1, 1988

By Kazimierz Gwizdala

In the paper the method for estimation of settlement of vertically loaded piles in a group is presented. The method is generally based on the hybrid procedure with non-linear solution for single piles and with interaction between them for the low-strain shear modulus. Some attention is paid to the influence of deformation and strength parameters used in calculations. The applied model is verified in the framework of the research programme carried out recently in the Geotechnical Department of Gdansk Technical University. It concerns monitoring and analysing the settlements of the existing structures on piles. A comparison of calculation and measurements results for two tested buildings is presented as an example.

Jan 1, 2002

By David B. Paul

"ABSTRACTThe US Army Corps of Engineers (USACE) has 704 dams in their inventory and over 100,000 miles of levees with a capital value of over $150 billion. Currently, there are 319 dams that are classified as high hazard and have actionable failure modes that will require structural modifications. The most frequent actionable failure mode associated with the inventory is seepage and piping. One of the most effective engineering solutions is the installation of a cutoff to limit seepage. Currently, USACE has over $1.5 Billion of cutoff wall projects under construction and/or design. Given the magnitude of the dam and levee safety issues, USACE is developing a new Engineering Manual (EM) titled “Seepage Control Cutoffs for Dams and Levees.” This EM covers all of the methods to construct cutoff walls. USACE has partnered with the Deep Foundation Institute (DFI) in preparation of the EM to ensure that it is comprehensive and draws from the expertise of the specialty foundation engineering companies that design, manufacture, and construct seepage control cutoffs around the world. The EM contains case histories as well as a comprehensive project statistical summary and guide specification paragraphs. The goal of USACE was to make the EM a state of the art document for use by Districts.HISTORYSlurry wall construction techniques were developed in the late 1940’s in Italy by ICOS. The first use of the slurry trench method of construction in the United States was by the USACE Memphis District in September 1945, to form a partial cutoff along the Mississippi River levee on the Arkansas side of the river just below Memphis, Tennessee. The idea for the project probably evolved from the use at that time of puddle clay trench cutoffs combined with the use of drilling mud for advancing borings. A paddle wheel mixing device was constructed for making slurry from native clays. Trenches were dug to a 20-ft depth using a trenching machine and to a 35-ft depth using a dragline with a 100-ft boom and 2-cu-yd bucket. Backfill was mixed in windrows at the site from hauled-in clay gravel and native materials and pushed into the trench by a bulldozer when the length of the trench was equal to about twice the trench depth. It is amazing that after almost 70 years, the technique is still about the same as it was when first developed by the Memphis District. A soilbentonite cutoff was constructed under the Kennewick Levee adjacent to the Columbia River as part of the McNary Dam Project in Washington by the Walla Walla District in 1952 The first application of a soil-bentonite slurry trench cutoff for control of underseepage at a major earth dam was at Wanapum Dam on the Columbia River in Washington in 1959.The first cement- bentonite cutoff in the United States was constructed at the Tilden Tailings Project to store tailings from the Tilden Mine in Michigan in 1976. The first cement-bentonite cutoff constructed at a dam on a river retaining a reservoir in the United States was completed in 1978 at the Elgo Dam (formerly the San Carlos Dam) in Arizona.The USACE has designed and constructed some of the deepest and most complex cutoff walls for dams since the 1970’s. The first major concrete panel cutoff wall constructed in a dam in the United States was at Wolf Creek Dam (Nashville District) by the ICOS Corporation between 1974-77. The dam has a long history of seepage issues associated with the karst geology that comprises the foundation. In 1968, about 17 years after first being impounded, wet areas, muddy flows in the tailrace and sinkholes in the downstream toe adjacent to the switchyard occurred."

Jan 1, 2014

By H. J. Siriwardane

This paper presents results from three case studies involving longwall mine panels at which the measured ground movements were compared with the numerical model predictions based on the finite element method. A new approach called the "displacement approach" was used in this study. The general concept of this method is based on the assumption that total roof collapse occurs behind the mine face as it advances. This assumption appears to be true for almost all longwall mining conditions. The prediction based on the numerical model appears to compare well with the measurements.

Jan 1, 1988

By Paul S. Goodman

Volume II The purpose of this study is to explain reasons for the productivity differences in mining crews. The literature on group productivity is examined. Then a new approach to estimating productivity differences is proposed and estimated across seven different mines. The results indicate a fairly robust model in terms of explanatory power. Recommendations on how the model can be used as a managerial tool are presented.

Jan 1, 1985

By Verya Nasri, Scott Thorburn

The City of Toronto and the Toronto Transit Commission (TTC) have conducted an Individual Environmental Assessment (EA) for a 6.2 km, 4-station underground extension of the Spadina Subway from Downsview Station to Steeles Avenue. This Environmental Assessment Study was performed in three phases including routes and general station locations, alignments and station concepts and detailed assessment of the effects of the undertaking. URS Canada Inc. has led the consultant team for this Study. The anticipated total duration of the project is approximately 6 years and its estimated total cost is about $1.4 billion. This paper presents the planning process of the project, the environmental and engineering challenges, and the measures taken to address them.

Jan 1, 2007

The failure of a seal in an underground coal mine can have devastating consequences. Traditionally seals have been constructed as flat walls. Large hydraulic dams, on the other hand, are constructed as concave arches. This paper presents an initial analysis of the potential strengthening of seals by concave construction as well as the impact of additional cost in terms of labor and material. A simple finite element analysis of three-dimensional solids under uniform loading allows comparisons between the strength of a flat wall and a curved arch. The models are examined for reasonable behavior and displacements at 20, 50, 100, and 200 psi loads.

Jan 1, 2007