Search Documents

By H Bruyn, K Ehrig, V Liebezeit, A Robertson, M Smith, D Grant

"The Olympic Dam geometallurgy program has generated a large quantity of data that has been used to create a geometallurgically enabled block model. An ongoing challenge is to convert data into usable information and embed geometallurgical practices into resource model development and mine planning to assist with the identification of opportunities to maximise value.This paper will discuss the methods used to disseminate geometallurgical information throughout the planning life cycle including data extraction methods from the geometallurgy acQuire database, and the inclusion of a geometallurgy module in the Olympic Dam Stope Reserves database. The use of geometallurgical information in short-, medium- and long-term mine design and scheduling, including its use in grade descriptor development and stope value assessment tools will also be presented. The detail of development of specific geometallurgical models is outside the scope of this paper.At Olympic Dam, the incorporation of geometallurgical capability within the long-term planning team, traditionally the domain of mining engineers, has proved essential in broadening the base of geometallurgical knowledge as well as focusing geometallurgy resources on value-adding areas while providing a holistic risk based long-term plan.CITATION:Liebezeit, V, Ehrig, K, Robertson, A, Grant, D, Smith, M and Bruyn, H, 2016. Embedding Geometallurgy into Mine Planning Practices – Practical Examples at Olympic Dam, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 135–144 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By John L. H. Patterson

Handheld XRF has become the favorite way of measuring the content and identity of alloys in the field. This is because of the very portable nature of the instrumentation and its simple operation. However, these analyzers have been unable to determine the concentration of the light elements like Mg and Si due to the very low energy of the x-rays produced by these elements. In the past accessories such as vacuum and He flush have given some analyzers the ability to determine these light elements with modest detection limits. The introduction of the Silicon Drift Detector (SDD) into this class of instrumentation has added a new level of analysis capability to portable XRF instrumentation. X-ray fluorescence is achieved by exciting a sample with a beam of x-rays, which in recent portable equipment are generated by a small tube. This results in the emission of characteristic x-rays from the sample under test. By measuring the energy of each x-ray it is possible to determine what element generated it. By counting the number of x-rays at each energy it is possible to determine the concentration of each element. The detection limit for each element is dependent upon the number of x-rays which reach the detector. As the number of x-rays increases the detection limit will improve. One of the major factors in an x-ray reaching the detector is the energy of the x-ray. As the energy of an x-ray increases the probability of that x-ray reaching the detector increases. The energy of an x-ray is inversely proportional to the atomic number (AN) of the element generating the x-ray. For example, an iron x-ray (AN=26) is 6.40 keV while an aluminum x-ray (AN=13) is 1.49 keV. As the energy decreases, the detection of the x-ray becomes less and less probable because the x-ray may be absorbed by the windows which are part of the instrument and detector or the air in the path between the sample and detector. In SiPIN based portable XRF analyzers, the lowest element which is detected with acceptable detection limits is normally considered to be Ti (AN=22). The detection limits for 60 second measurements on typical SiPIN XRF analyzer are given in Table I. Thus, portable analyzers have not been useful for measurement of aluminum and titanium alloys as major components of these alloys are Mg (AN=12), Al (AN=13) and Si (AN=14).

Jan 1, 2009

By M Franklin, C Puglisi, S Fitch

Implementation of a well planned and executed Management Operating System (MOS) can result in widespread improvements to operational performance but its success relies heavily on the investment by and engagement of the larger workforce with the project. Over the seven month period of the Telfer MOS project, significant improvements were achieved; a 20% increase in monthly hoisted tonnes from the open stope and sublevel cave operations and a 45% increase in square metres of ore extracted from the narrow vein operation. The Telfer MOS was undertaken with the intention that the project wasn’t solely about producing new tools, it hinged on the investment and behaviours of the personnel affected by these tools and alterations. To ensure that the project ran smoothly, the Byrnecut senior leadership team and their operators were heavily involved in the project’s development. In the initial stage, Telfer’s MOS project determined that the quality and accuracy of the information received in the form of radio calls to mine control and completed operator plods was questionable. This required an overhaul of the data collection and verification process in the form of altered operator plods, which was then cross referenced with the operator’s radio calls to mine control. Once the data collection and verification process was implemented, the Telfer team was then able to produce several tools with the aim of providing visibility to the data being captured and its implications. These tools allowed the mine foremen to determine whether equipment was being under-utilised and where they should focus their production efforts to meet monthly targets. Whilst the initial underground project is now complete, the implementation of MOS across the entire site is ongoing with significant operating improvements occurring.

Mar 15, 2021

By Atta Ur Rehman, Kwame Awuah-Offei

This paper examines the effect of bucket geometry (cutting-blade profile, floor profile and blade thickness), speed, motor power output and muckpile particle sizes on bucket penetration and draft for rubber tire loaders. The work uses a 1:16 scale model of a load-haul-dump (LHD) in full-factorial experiments to examine the effect of the variables on penetration and maximum draft. The results show that speed and motor output are positively correlated with penetration and draft, and muckpile particle size is positively correlated with penetration and negatively correlated with draft (p < 0.0014).

By N. S. Dalal, Xianglin Shi

"INTRODUCTIONEpidemiologic studies of workers in chromate-ore related industries, 1-3 and stainless steel welding and related occupations4 have shown that they have about 20-40 times higher risk of throat or respiratory track cancer than controls. Although the actual carcinogenic substances were not identified in these statistical studies, Cr(VI) compounds (for example, calcium chromate, zinc chromate, and lead chromate) were implicated as the causative agents, whereas Cr(III) compounds were not suspected as carcinogens. s These suggestions were supporte4 by laboratory studies wherein many Cr(VI) compounds produced sarcomas at the implant or injection sites.1,5 Squamous cell carcinomas and adenocarcinomas closely resembling human lung cancer were induced by intrabronchial implants of calcium chromate in rats, 6·7 whereas Cr(DI) oxide and Cr(lll) sulfate did not induce any tumor formation.6,7While the mechanism of the chromate-induced carcinogenicity is not fully understood, it is generally thought8 that it involves some damage to DNA. Specifically, it has been reported that: a) the chromate ion, henceforth referred to as chromate, can pass through the cell membrane and enter the cell while CR(DI) does not, 9 b) chromate does not interact with either native or denatured DNA 10 while Cr(III) does, 11 and c) the final Cr-DNA complex isolated from cellular reactions of chromate is Cr(III)-DNA, with Cr(III) binding to the phosphate groups.12,13 Thus the important question is: since Cr(DI) cannot pass through the membranes, how does Cr(III)-DNA complex form? For this to happen, Cr(VI) must be reduced to its lower oxidation states, 14 ultimately to Cr(III), by some reductants in the cellular environment. Unless this reduction occurs, the DNA would not be damaged and therefore no chromate carcinogenicity would ensue. Thus the reduction of chromate to its lower oxidation states seems to be a key step in the chromate carcinogenicity .1s One of the major reductants in cellular environments is thought to be glutathione (GSH), both outside and inside the cells.16-lB Some evidence for the role of GSH in the chromate toxicity was provided by recent studies showing that exposure of hamster cells to non-toxic levels of added selemite increases the levels of GSH as well as the Cr(VI)-induced DNA strand breaks,19 and that such DNA strand breaks in hepatocytes also change in direct proportion to the GSH content. 20,21 These observations were interpreted as implying that the reduction of chromate by GSH to some reactive intennediate is an important step in the chromate carcinogenicity. 20.21 In · the present undenaking22 we have used electron spin resonance (ESR) and spin-trap methodology to investigate the reduction of chromate by GSH and find evidence for the involvement of the glutathionyl radical (GS ·) as well as Cr(V)-intermediates."

Jan 1, 1990

By Edward P. Hagarty

The Hazardous and Solid Waste Amendments (HSWA) of 1984 added Subtitle I to the Resource Conservation and Recovery Act (RCRA), authorizing the Environmental Protection Agency (EPA) to develop and implement a new regulatory program for Underground Storage Tanks (USTs) containing petroleum and other regulated substances. Technical standards required for release detection, prevention, and correction as necessary to protect human health and the environment were promulgated as described in 53 Federal Register 37082 (September 23, 1988). Virginia State Regulations (VR 680- 13-02) and U.S. Army Regulations require that a Corrective Action Plan and a Site Clearance Report be prepared to explain the details of remediation of any contaminated media. Construction of new buildings is proposed in two different areas at Fort Myer in Arlington, Virginia, where USTs containing gasoline, diesel and heating oil were located. Tightness testing performed on these USTs in September 1991 indicated that some of the tanks were leaking. Many of the tanks were removed for permanent closure. Initial Abatement (excavation of contaminated soil) was &ed out immediately. A detailed Site Characterization Study which included Hydropunch", field screening using immunoassay, and pilot test - dual phase (water and soil gas) extraction was conducted. Environmental media were analyzed for volatiles, semi-volatiles and metals. A detailed risk analysis (RA) was performed to determine risk-based clean up levels for benzene, toluene, ethylbenzene, xylenes (BTEX); polycyclic aromatic hydrocarbons (PAHs); and methyl-tertiary butyl ether (MTBE). The RA also discussed the presence of lead in the soil. Before constructing any buildings in these contaminated areas, remediation must be conducted in accordance with the State, Federal and other applicable regulations. The remedial alternatives evaluated included Vapor Enhanced Groundwater Extraction, Soil Vacuum Extraction, Soil Washing, Soil Steaming, Active and Passive Ventilation SolidificationlStabilization, Vapor Barrier Construction, and Excavation with Off-site Disposal. This paper discusses: (a) delineation of soil contamination @) risk analysis (c) evaluation of remedial alternatives and selection of the most appropriate technology and (d) consideration of various regulatory issues.

Jan 1, 1994

By Ygor Macabu de Moraes, Jean Igor Margem, Carolina Gomes Dias Ribeiro, Frederico Muylaert Margem, Sergio Neves Monteiro, João Batista Vasconcelos

A natural fiber presents interfacial characteristics with polymeric matrices that favor a high impact energy absorption by the composite structure. The objective of this work was then to assess the Izod impact resistance of polymeric composites reinforced with one or two layers of batt malva and jute fibers. The results showed are markable increase in the notch toughness with increasing layers of mauve blankets and jute.This can be attributed to a preferential debonding of the fiber/matrix interface, which contributes to an elevated absorbed energy.

Mar 1, 2017

By J. C. Wynn

J.R. Hillebrand From the abstract, "A realistic ore deposition model to serve as a conceptual framework." Further, on page 246, "The first area of study was the Josephine peridotite, now identified as an ophiolite terrane, located in northern California and south-western Oregon (Fig. 3). Here, it was felt that we could test the models shown in Figs. 1 and 2 and, if successful, expand the model and test it in other chromite districts in the US and around the world." My comments refer only to chromite deposits in Europe and the Middle East. First, I question that may chromite deposits occur in the idealized ophiolite section shown in Fig. 1. Second, although some podiform deposits (referring to morphology) have been important (Guleman, Turkey, for example), the stratiform deposits are of greater importance in tonnage and frequently grade. Examples include Nada, Yugoslavia; Bulqiza, Albania; Xerolivado, Greece; Saranovsk, Russia; and Abdasht, Iran. Reply by J.C. Wynn Mr. Hillebrand raises two issues that deserve a serious response. One issue is basically subjective and the other is ultimately political. First, the question of where (and how many) podiform chromite deposits are found in the idealized ophiolite section of Dickey (1975). The Dickey model is still perhaps somewhat controversial (Panayoutou, 1980), but our experience in the Josephine ophiolite of northern California (Wynn, 1980; and Albers, 1983) shows that the model works well there. Virtually all the chromite is found in dunite lenses in the tectonite peridotite (harzburgite). Since there are few complete ophiolites exposed in the world, the model will probably never satisfy everyone. The degree of acceptance is a function of any individual&apos;s subjective experience. Second, it is well known that stratiform chromite contributes more than 95% of the chromite reserves presently known in the world, and it could be reasonably argued that there is no point in exploring for or exploiting podiform deposits further. The title of the paper, however, was in part &apos;strategic minerals geophysical research&apos;; chromite is considered a strategic and critical mineral of the US and many other industrialized nations. Stratiform deposits in South Africa and Zimbabwe account for most of the chromite reserves in the world. Unfortunately, experience in modern times with substantial price fluctuations and even resource cartels dictates the wisdom of identifying and maintaining a national chromite reserve, irrespective of the cost. An improved exploration methodology is an essential element in this strategic objective. References Albers, J.P., 1983, "Geological and Geophysical Studies of Chromite Deposits in the Josephine peridotite, California and Oregon," US Geological Survey Bulletin 1546 A-D, 118 pp. Dickey, J.S. Jr., 1975, "A Hypothesis of Origin for Podiform Chromite Deposits," Geochimica et Cosmochimica Acta, Vol. 39, pp. 1061.1074. Panayiotou, 1980, Proceedings, International Ophiolite Symposium, Cyprus, 1979, 781 pp. Wynn, J.C., 1980, "Exploration Geophysical Methods and Strategies, and Their use to Locate and Assess Small Mineral Deposits," Chapter 12 of Meyer and Carmen, eds., The Future of Small Scale Mining, McGraw-Hill, New York, pp. 75-83.

Jan 12, 1983

The Red Lake greenstone belt is an irregular mass of lavas sedimentary rocks and intrusives which is approxiately 35 miles long 18 miles wide and 7 miles deep. Basaltic volcamcs are the oldest rocks w1thm the belt. They are believed to have been laid down on an ancient crust which is at least 3 billion (3 x 109) years old and was composed partly of sediments. The basaltic rocks are overlain by acid volcanics and sedimentary rocks which have been complexly folded and are preserved as a down-folded remnant of younger rocks within the older crust. The volcanics and sedimentary rocks of the greenstone belt have been cut by intrusives with a wide range of composition. The emplacement of the intrusives and the accompanying regional metamorph-ism which terminated the orogenic activity in this area are believed to have occurred approximately 2.4 billion years ago. The basalts and many of the basic and ultrabasic intrusives undoubtedly had their source in the sub-crust or mantle. At least some of the granitic intrusives are believed to have had

Jan 1, 1965

By C. W. Robinson

El presente texto describe el problema del nacionalismo de las realidades de la expropiación latinoamericana. Uno de los principales problemas radica en las relaciones de Estados Unidos con América Latina - en tanto el nacionalismo genera una sensibilidad emocional y política que contrapone la posición del país inversionista extranjero. Por ello, se debe eliminar el aspecto político o desnacionalizar las inversiones extranjerases necesario, de forma que el desarrollo de consorcios para inversiones de mayor envergadura formados por participantes de dos o más naciones, puede reducir el riesgo de ataque político basado en el argumento de 'invasión de soberanía".

Jul 1, 1972

By Andrew Lewis, Amarit Nitaramorn, Alexander Garcia, Peter Altounyan

"Indonesia is a major coal producer, the vast majority being sourced from opencast operations. Underground production to date has been constrained by unfavorable ground conditions and limited local experience. However, an underground trial in East Kalimantan has now shown that it is possible to successfully extract coal and mine safely, despite the technical challenges.A trial drift mine has been worked to a current maximum depth of 160 m (525 ft) in a dipping coal seam. The 3 m (10 ft) thick coal seam is overlain by very weak mudstone and sandstones. The mudstone forming the immediate seam roof strata proved a particular challenge given its adverse reaction to water and overall friability.Rock bolts were used as roadway support, the system being carefully selected to optimize effectiveness. An innovative method of partial extraction was trialed, which demonstrated the potential for productive mining despite the ground conditions. Roof falls have occurred within the working area, and roadways demonstrate reasonable stability over time.Throughout the course of the trial, strata behavior monitoring has been an important aspect, and a comprehensive ground control monitoring system is in place. This has enhanced the ability to increase the level of support where required and to react to deteriorating conditions. In addition, monitoring information has allowed a quantitative assessment to be made of the technical feasibility of future full-scale mining.INTRODUCTIONWith current production at over 200 million tons, much of this destined for overseas markets, Indonesia is the second largest exporter of coal (Ritschel and Schiffer, 2007). The majority of the coal is sourced from the Kalimantan coalfields. Mining is predominately opencast, yet in recent years there have been attempts made to introduce underground operations. This move would permit continued access to good quality seams that are beyond the reach of viable opencast mining."

Jan 1, 2010

By Wen H. Su

This paper examines the intrinsic mechanisms of cutter roof by combining field investigation, laboratory testings, underground instrumentations, and numerical modelling. Cutter roof developed during the development of a set of longwall panel entries in a West Virginia coal mine was presented as a case study. Mining alternatives applicable to the mine are recommended. Cutter roof occurred in two other West Virginia coal mines were also investigated Detailed comparisons were made among the three cases. As a result of the extensive investigation, intrinsic mechanisms of cutter roof failures under various conditions are presented from the practical and theoretical points of view.

Jan 1, 1985

By Tung Vu, Michael Harrington

"The Regional Connector project is a complex subway light-rail project that runs through the heart of downtown Los Angeles, CA. The design-build contract was awarded in April 2014 to the Regional Connector Constructors (RCC), a joint venture between Skanska USA Civil West California District Inc. and Traylor Brothers Inc., and their designer team consisting of Hatch Mott McDonald (HMM) and subconsultants. The project broke ground on Sept. 30, 2014 and is expected to be completed in winter 2021-2022. The main components of the project consist of 6.4-m (21-ft) diameter twin-bored tunnels, three crosspassages, a 87-m (287-ft) long crossover SEM cavern, three new underground stations, and cut-and-cover tunnels along South Flower, Alameda and 1st Streets. The project map is shown in Fig. 1. The design and construction challenges associated with each of these main components are discussed in the following sections.Project designTunnels. The Regional Connector tunnels are located primarily within the Fernando formation consisting predominantly of extremely weak to very weak, massive, clayey siltstone. About 305 m (1,000 ft) of tunnels on the eastern end are in alluvium and mixed face of Fernando formation and alluvium. The tightest curve of the tunnel alignment is 178 m (583 ft) in radius. The tunnels were designed with a reinforced precast concrete tunnel lining (PCTL) to be used with an earth balance pressurized (EPB) tunnel boring machine. The PCTL ring is 5.5 m (18 ft-10 in.) inside diameter, 27 cm (10.5 ft) thick, 1.5 m (5 ft) long, and consists of five segments and a key. The segments were designed with 6,500 psi concrete, 80 ksi yield strength wire rebar, convex joint surfaces to enhance seismic performance, and a dosage of 1.7 lbs polypropylene microfibers per cubic yard of concrete for fire resistance. The rings are designed with a right ring and left ring pattern and a taper of 3.8 cm (1.5 ft) to allow for alignment curve negotiation. Figure 2 shows typical sections of the PCTL. The structural lining design was modeled using FLAC 3D. Four consecutive rings were modeled with 32 dowel connection. Loading considered in the lining design includes temporary ground load during excavation, long-term ground loads, seismic loads and train loads. The seismic loads on the PCTL were simulated with the racking deformation applied at vertical boundaries of the model. Due to variation of geologic condition along the tunnel alignment and different surcharge requirements, three different types of reinforcement (typical, heavy and extra heavy) were designed. The typical type PCTL was required in Fernando formation, the heavy type was required in alluvium or mixed-face condition, and the extra heavy type was required in alluvium and underneath the Japanese Village Plaza where a surcharge of 1,000 psf was required."

Sep 1, 2019

By Osvaldo A. Bascur

One of the most vigorous of the continuous improvement methodologies is Six Sigma. While usually associated with improving manufacturing and product quality, leading manufacturers are using it to improve their extended supply chain and logistics capabilities. At the same time they are improving reliability, some companies have cut hundreds of millions of dollars of fat out of their supply chain. Mine to Mill optimization is a transformation of culture from processing tons to processing a quality feed size distribution which reduces the overall operational costs and add the highest value to the mine. This is not a constant endeavor. As such, a dynamic performance monitoring and diagnosis is necessary. We will review a systemic way to performance improvements and avoiding metal losses from the blast to the metals. We show the requirements of using raw data to analysis the data to define operational maps which provide assistance to run the mine and mill. A case study is provided with the mine and mill data was integrated combining process control and quality information resulting in reduction of water and energy consumption while improving the overall value of the mine. The results of reengineering the current system with this SIX SIGMA Strategy had the following results: an increase of ore milling: 4.6% decrease of mil power: 3.9%, decrease of fresh water consumption: 6.8%, with a total of net profits: US$ 31.8 million, the PI System infrastructure contribution: US$ 7.95 million. These estimates were for the period 2009/04/04 to 2009/12/31.

Sep 1, 2012

By A. J. Paul Laprairie

The process for which it is to be used is too often the only consideration in the design of a vessel. A de-sign allowing for practical manufacture and erection, as well as for proper maintenance, can often give over-all economies. Most platework in-stalled today is of welded construction. Therefore, metallurgical control is important in its manufacture. Also, because many concentrating and re-fining processes tend to be corrosive, the subject of protective coatings as a part of the manufacturing process is extremely important. The plant de-signer should know how to evaluate and specify controls for the metallurgy and for the coatings. Mining operations are becoming more sophisticated in the field of mechanical engineering. More and more emphasis is being given to preventive maintenance. The first step in any maintenance program, however, is good inspection service. This paper will suggest methods for the inspection of platework, and outline methods for repair and replacement.

Jan 1, 1963

By D Teyhan, J Kirsch

Traditionally, most Australian iron ore mining operations have been surface-based. Processing plants were designed to handle dry ores. In recent years mining operations in the Pilbara have progressively moved below the water table exposing wet, sticky ores which have caused lost efficiency in screening operations as particles tend to agglomerate and adhere, blinding screening media. Miners and vibrating screen manufacturers have experimented with a shift from linear motion to elliptical motion screens. Elliptical motion conveys and lifts particles. Effective on flat deck (horizontal and inclined) or sloping decks it can be configured to provide a controlled transport rate, applying pressure in all directions to maximise screening efficiency. In practice, elliptical motion screens have proven to be effective in dislodging sticky particles from screening media, reducing blinding rates and improving screen efficiency. Moisture and clay content change during the life of a mine. These changes are sometimes the effect of seasonal rainfall, in other cases due to increased groundwater and clay content as mining operations go deeper. To compensate for such changes and optimise screen efficiency, changing the ‘shape’ of elliptical screen motion is required. This has traditionally required shutting down processing plants and making mechanical screen adjustments. Plant downtime is costly and machine adjustment has been a ‘trial and error’ practice. This paper will explore the results of a field trial that is currently underway in Brazil of a next generation elliptical motion screen design that allows operators to make changes to exciter rotational direction, speed and screen stroke angle, through electronic drive phase control. The machine’s electronic drive system synchronisation is enhanced for stability with a unique mechanical timing system. Operating at up to 6 g, screen adjustments can be made on the fly without stopping production. Early trial results are showing up to 50 per cent improvement in screen efficiency compared with traditional elliptical motion machines under certain feed conditions.

Aug 24, 2022

By Frank E. Cash, Max S. Petersen

"INTRODUCTION Explosives have been used in ever—increasing amounts since gunpowder was invented. For hundreds of years only low explosives of the deflagrating type were used, and they were fired by means of a flame or hot object. Ben¬jamin Franklin first ignited gunpowder from a distance in 1751 by means of an electrostatic spark. Further efforts to develop a satisfactory electrical method to ignite explosives from greater distances were overshadowed by the invention of safety fuse in 1831, as this offered a relatively simple and inexpensive means of firing explosives.The discovery and introduction of high explosives of the detonating type and the invention of the fulmitate of mercury blasting cap about the middle of the nineteenth century provided the needed impetus for inventors to develop means of firing the cap by electricity. The original high-tension igniter, following Benjamin Franklin's experiment in which the detonating compound was ignited by a spark, was discarded in favor of a low-tension igniter, in which the detonating compound was ignited by a heated wire. The past 2 decades have seen considerable improvement in the design and construction of electric detonators to make them safer and more efficient, yet in spite of the improvement it is estimated that less than 50 percent of the explosives used in industry today are ignited or detonated electrically. The trend, however, is toward the use of electric methods. In recent years numerous-mining companies have introduced electric blasting exclusively at their mines as a means of improving safety and efficiency."

Sep 1, 1946

"The Cordillera contains numerous porphyry deposits and prospects, many containing economic quantities of copper, molybdenum, gold and tungsten. Over the lost twenty years, different phases of exploration have been driven by individual commodity prices and new discoveries. Exploration methods have remained largely unchanged since the 1960s and 1970s with the range of techniques chosen for each situation depending on the stage of the program, the type of porphyry target and the local environment. Improvements or changes to techniques have resulted from awareness of specific features in new deposits or regional problems. During the last ten years much of the emphasis has been on the re-evaluation of known porphyry deposits with more exploration in areas previously recognized as prospective. Re-evaluation of known deposits has resulted in increased reserves, often with improved gold grade, and the discovery of new zones. Several new deposits have been discovered including gold-only deposits of probable porphyry affinity.Research related to porphyry deposits has followed trends in exploration and has been directed toward the type of deposits that have been of current interest. In addition to research on specific deposits and areas, general research related to porphyry deposits has addressed three broad themes. The first theme involves the role of tectonic processes and the nature of source regions. Although different in detail, recent tectonic models suggest that a tectonic change or hiatus may be important for the generation of metal-rich magmas from various source regions and subsequent fractionation that permits volatile saturation. The second theme is based on magmatic processes, particularly the generation of a volatile phase enriched in metals. This research supports the general orthomagmatic model for porphyry deposits and has helped to define the influence of specific variables in the generation of different types of porphyry deposits. Finally, research on alteration and mineralization has provided evidence for different types of fluids and fluid processes involved in the formation of porphyry deposits. These data also support the orthomagmatic model but indicate additional complexity in magmatic-hydrothermal systems including the role of external fluids. Although important advances have been made, research has had a limited impact on exploration.Exploration and research on deposits that occur in the peripheral and upper parts of porphyry systems have been important over the last ten years. Although considerable advances have been made, the relationship of different styles of peripheral mineralization to magmatic processes in the core of the system remains ambiguous. An improved understanding of the processes that generate zoning, peripheral mineralization, and the surrounding alteration envelopes would be beneficial to exploration."

Jan 1, 1995

By William G. Ryan, David S. Graham, Dan A. Brown, Rich A. Lamb, Paul J. Axtell

"The St. Croix River Crossing project on the Minnesota-Wisconsin border has been in the process of planning and public debate for two decades, with several changes in alignment. During the course of the earlier planning process in 1995, a drilled shaft load test was performed to obtain preliminary design information. There were some difficulties in maintaining stability within the weak sandstone bearing formation, and the measured axial resistance was relatively low. Subsequent experience by the Minnesota Department of Transportation with similar weak sandstones on the I-35W project suggests that improved construction techniques using modern drilling fluids may offer opportunities for improved performance. During final design in 2012 a second load test program was performed of a full scale test shaft constructed using polymer drilling fluids. The stability of the socket excavation in the weak sandstone appeared to be greatly improved and the measured axial resistance significantly higher.This case history illustrates the excellent performance that drilled shafts can provide in even relatively weak sandstone bedrock as well as the profound influence on axial resistance associated with the construction techniques used. The improved resistance values obtained by the new load test with more recent construction technology allowed the foundation scheme to be substantially optimized with respect to the number and size of required drilled shafts, reducing the size, cost, and risk of the coffercells and footings.IntroductionThe Minnesota Department of Transportation (MnDOT) has awarded the first phase of a bridge construction project that will cross the St. Croix River between Oak Park Heights, MN and St Joseph, WI. The first phase construction contract involves building the river pier substructures including groups of drilled shafts beneath each tower leg. A general location of the bridge project is provided in Figure 1.Prior to award of the construction contract, two separate design-phase axial load tests were performed on non-production drilled shafts with rock sockets. Both tests were static, bottom-up tests using the Osterberg Cell (O-cell). The first test was performed in 1995 when final design and construction was thought to be imminent. After years of public debate and literally, an act of Congress, design of the project was finally restarted and a second load test performed in 2012. The 1995 test was conducted on the Minnesota bank approximately 900 ft southwest of the St. Croix River bank. The 2012 test was conducted in the river about 2,100 ft northeast of the1995 test location. A plan-view of the project indicating the test program locations relative to the bridge alignment is provided in Figure 2."

Jan 1, 2015

By Greg Nutson, Jeremy Butkovich, Bill Perkins, Hollie Ellis, Paul Bott

"Dynamic soil-structure interaction (DSSI) analyses are becoming more common in bridge designs, especially in seismically active areas. Because of its proximity to two active fault zones, the Evergreen Point west approach bridge replacement will be base isolated, and will be designed using DSSI. The project team completed two independent bridge designs to satisfy peer review requirements. The designs required substantial characterization of the soil dynamic behavior using both laboratory and in-situ testing. The analyses made use of earthquake time histories spectrally matched to conditional mean spectra. This led to reduced, and more realistic seismic demands on the structure, compared to conventional uniform hazard spectrum matching. The bridge analyses suggest that the preliminary bridge design is relatively conservative. This will allow the design team to potentially reduce shaft/column diameters and reinforcement. The design team estimates that the dynamic analysis design could represent a net savings of around $60 to $90 million compared to a conventional design.INTRODUCTIONThe Evergreen Point Bridge conveys State Route (SR) 520 2.6 miles (4.2 kilometers [km]) from Seattle to Medina across Lake Washington. The bridge is located in a seismically active area, and the Washington State Department of Transportation (WSDOT) has determined that the western half of the 1960s-era bridge (the “west approach”) is vulnerable to earthquake damage. WSDOT has begun preliminary design to replace the west approach bridge.The west approach extends about 6,100 feet (1,900 meters [m]) east from Seattle’s Montlake neighborhood, over Union Bay and Foster Island, then into Lake Washington proper (Figure 1). Approximately 5,600 feet (1,700 m) of the replacement bridge would be constructed over water. Subsurface conditions along the bridge alignment consist of 5 to 80 feet (2 to 24 m) of very soft peat and clay, over very dense/hard sand and clay. Multiple pile supported columns support the existing bridge. The new bridge would be supported by 8- to 10- foot-diameter (2.4 to 3.0 m) drilled shafts that extend about 50 feet (15 m) into the underlying very dense/hard soil. To reduce seismic demands on the bridge superstructure, WSDOT has decided to incorporate a base-isolation system into the bridge design."

Jan 1, 2017