Search Documents

By LINDSAY BOTTOMER, Tassos Grammatikopoulos, Massoud Aghamirian, MARK FEDIKOW

A master composite (Master Comp) sample was prepared from three pegmatite zones from the Zoro Dyke D1 for mineralogical analysis and heavy liquid separation (HLS). The mineralogical examination was conducted on a subsample that was crushed to approximately P80 = 600 μm. The sample consists of spodumene (10.5 percent), quartz (29.3 percent), plagioclase (29.0 percent), K-feldspars (21.3 percent), micas (5.1 percent), tourmaline (2.9 percent) and Fe-Mn-phosphates (0.1 percent). Liberation of spodumene (88 percent) and gangue minerals, including quartz (89 percent), feldspars (94 percent) and micas (83 percent), is very good at this P80 . The average lithium (Li) concentration is 3.7 percent in spodumene, 2,196 ppm in micas, 1,001 ppm in tourmaline and 115 ppm in K-feldspars. Spodumene accounts for 96 percent of the total Li in the sample. The mineralogical data indicate the potential to recover spodumene by flotation with minimal Li losses due to other Li carriers. The HLS was conducted on a subsample that was crushed to smaller than 6.4 mm, with the smaller than 600 µm fraction removed from this test. The HLS results indicate it is possible to produce a high-grade lithium concentrate, with close to 6 percent Li2O, after the rejection of iron silicates with magnetic separation.

By T. H. Dubaniewicz

Fiber-optic technology is progressing rapidly, including the development of fiber-optic sensors for many applications. These sensors have the advantages of high sensitivity, light weight, small size, high bandwidth, and freedom from electromagnetic influences. The U.S. Bureau of Mines is investigating the use of fiber-optic technology to monitor mine atmospheres. This report describes a methane monitor based on differential absorption of infrared light. The monitor can detect methane concentrations as low as 0.2 vol pct as far away as 2 km via fiber-optic cable. The upper range is 100 vol pct methane. Since the system requires no electrical power within the mine, it is intrinsically safe.

Jan 1, 2010

By Luca Pingue, Regine Jagow-Klaff, Franco Muratore, Carlandrea Albonico, Damiano Frontini, Rudolf Wernecké

This paper describes an artificial ground freezing (AGF) application carried out to ensure both watertightness and structural support for the safe excavation of four cross passages of the Forrestfield Airport Link (FAL) project in Perth. The line will deliver 8.5 km extension of the existing urban rail network connecting the growing eastern suburbs of Perth with the existing suburban rail network. The proposed soil improvement technique is adopted as a smart alternative to jet grouting from the surface since the use of heavy equipment with long vertical mast was not allowed due to the line underpassing an airport in operation. In this paper, details of the challenges and lessons learned during both design and construction phases are given. Furthermore, it is described the geometry and the installation of freeze pipes in presence of a massive steel frame, ventilation system and slurry pipes of the tunnel boring machine (TBM) in operation. It is also illustrated the web monitoring system to allow key personnel to follow in real time the development of soil temperatures, tunnel convergences and ground surface deformations as well as changes in the interaction between international parties involved due to the COVID-19 pandemic.

May 1, 2022

By P. Cowx, L. Els, P. Smith, R. Nordhagen

"Tapping operations at ferroalloy smelters generate a significant amount of fume. Effective capture of fumes is required to meet the obligations of environmental, as well as occupational, legislation.A study was completed on an existing fume extraction system at a ferromanganese furnace tapping area. The area under consideration included the tap-hole, launder, and ladle area. The study consisted of site test work as well as computational fluid dynamics (CFD) modelling to identify and evaluate solutions.Site test work and observations during furnace operation provided a baseline of system performance as well as input parameters for CFD modelling. Gas flow rates and energy contents from each extraction area were measured. Photographs and video footage were taken to evaluate areas of fume leakage.The CFD study was firstly validated against site observations to ensure the accuracy of input parameters. Thereafter several modification concepts were modelled and suitable combinations were investigated to ensure robust solutions. The following concepts were considered:•,Air curtains•,Ladle hood aspect ratio and position•,Increase of ladle extraction volume•,Extension of the length of the tapping garage structureThe paper presents the results of a performance test on a working ferromanganese tapping area fume extraction system and the results of CFD modelling as compared to site test results. Upgrade options are evaluated and an integrated robust upgrade of the system described."

Jan 1, 2014

By Roger J. Araujo

A photochromic material is one which undergoes a change of color when exposed to light and reverts to its original color when the light is removed. Review articles carrying extensive bibliographies have been written by Brown and Shaw (1) and by Schwab and Bertelson (2). Organics. Schwab and Bertelson divide the reactions in different organic photochromic materials into some half-dozen categories; Windsor (3) reduces these to the following three main classes of general interest, based on how they work. 1. Stereoisomers. Absorption of light breaks one of the chemical bonds in a. ring molecule, thus allowing the molecule to unwind and form a different geometrical arrangement. The reverse process is a reforming of the bond. Examples of this class are the spiropyrans and the anils. 2. Dyes. A triphenyl methane dye, for example, is oxidized by energetic light; the absorption characteristics of the positive ion so formed are different from those of the original electrically neutral benzene rings. 3. Triplet States. In the class of polynuclear aromatic hydrocarbons, ground-state molecules are excited first to a singlet state by irradiation, and then go, via the lowest triplet state, to an excited triplet state. Visible light is absorbed in the triplet-triplet transition.

Jan 1, 1970

By D Readett

The most critical variable in the successful establishment of the Murrin Murrin Heap Leach plant was the effective agglomeration of the Ni laterite ore. This paper describes the test work undertaken to establish the key agglomeration parameters including state of the art testing and analysis procedures. These parameters were then utilised to establish the key design and operational concepts for the world’s first commercial scale Ni laterite heap leach. Following the technical and economic success of the operation, the actual operational data is compared back to the original test work data.

Aug 8, 2011

By C. H. Stockwell

"The Precambrian rocks of southeastern Manitoba contain a great variety of mineral deposits, including gold, chromium, copper, nickel, lithium, tin, beryllium, tungsten, and molybdenum. Although considerable interest has been shown from time to time in each of these types of deposit, production to date has been almost entirely in gold. This has had a value of about $26,000,000 and has been derived chiefly from the San Antonio mine, with lesser amounts from the Central Manitoba, Gunnar, Beresford Lake, Ogama-Rockland, Diana, and other properties.Most of the deposits lie within volcanic and sedimentary rocks or within basic intrusions cutting these rocks. These favourable rocks occur in several areas, which have been given local names and are separated from one another by large bodies of granite (Fig. 1).In general, the several areas are characterized by different types of mineralization. Thus, the Rice Lake-Beresford Lake area contains numerous gold deposits and has yielded almost all the gold production to date; the Maskwa River, Euclid Lake, and Oiseau River areas are, on the whole, characterized by deposits of chromium, copper, nickel, lithium, tin, and beryllium; and in the West Hawk Lake area there are deposits of gold, tungsten, molybdenum, and lithium.As might be expected in a district containing such a variety of mineral deposits, the structural conditions controlling their deposition also vary greatly. It is, accordingly, convenient to discuss the structural geology and mineral deposits of each of the more important areas separately."

Jan 1, 1954

By L. H. Kalenowski

The metal lithium, its alloys, and its salts are becoming Increasingly important as industrial materials. Lithium metal, because of its great affinity for elements, such as nitrogen, hydrogen, oxygen, sulfur, phosphorus, carbon, and silicon, has become important for a wide variety of uses, ranging from purifying helium gas by removing the nitrogen to scavenging molten metals of undesirable impurities. The excellent fluxing properties of lithium salts have found increasing use in such applications as fluxes for welding aluminum and in lower melting ceramic glazes and coatings. Lithium chloride is one of the most hygroscopic salts known and is widely used as a dehumidifying agent. .About 17 lithium minerals are known. Four of these have commercial importance: Amblygonite, lepidolite, zinnwaldite, and spodumene. Spodumene is the most important source of lithium and lithium salts at present, but sizable deposits of amblygonite occur in the pegmatite area of the Black Hills of South Dakota. The size and nature of these deposits preclude the, possibility of, any assurance of an adequate supply of amblygonite for an operation processing only this mineral. Frequently spodumene and amblygonite occur associated in pegmatite minerals. Preliminary investigations indicate that a simultaneous recovery of spodumene and amblygonite can be made by froth flotation. A single process for treating spodumene and amblygonite or mixtures of thorn, would make possible more use of amblygonite as a source of lithium and obviate the separation of spodumene and amblygonite when they occur together.

Jan 1, 1952

By R. I. Jaffee, H. P. Nielsen

In recent years much attention has been given to high melting alloy systems. It has been of interest in this respect to investigate the alloys of platinum and tungsten, which were known from the literature to have very high melting points up to about 50 pct tungsten, but about which little had been published on the high-tungsten side of the system. Powder metallurgical methods were used throughout this investigation for the preparation of the alloys, utilizing electrical sintering techniques such as are used for tungsten and molybdenum. In the course of the work it was found desirable to determine fusion temperatures of the alloys, and it was possible from these and other data to draw a tentative constitutional diagram (solidus, mostly) applicable to the high-temperature part of the system. No attempt was made to determine solid solubility vs. temperature data, nor to investigate the lower temperature transformations in the solid state. Data on the microstructure, hardness, and a note on oxidation resistance of the sintered alloys were obtained. Past Work Miillerl determined liquidus temperatures of platinum-rich alloys to 50 pct tungsten, using a radiation method employing a photoelectric cell, and found that the melting points increased progressively from I771 C for platinum to 2350°C for the 50 pct alloy. Microscopic evidence by Miiller that complete solid solutions exist to 50 pct tungsten was not checked by Kremer2 who, according to Vines and Wise,3 found that "although the 8 pct tungsten alloy was a solid solution, the 26 pct tungsten alloy contained a eutectic or an intermediate phase." Hultgren and Jaffee4 using X ray methods found continuous solid solutions to at least 33.6 pct tungsten (35 at. pct) after annealing in vacuum for 6 days at I000 C. Vines and WiseS report work communicated to them by E. C. Rhodes on wrought alloys to 7 pct tungsten, which showed that tungsten hardened platinum extremely rapidly, and was one of the most potent hardeners of the binary additions to platinum. Considerable quantities of 4 pct tungsten platinum wire have been produced for grids in radar tubes and for aircraft spark plugs. Some of the alloy for the latter application is made by sintering, the remainder by smelting and casting. Materials The platinum powder used in this work was kindly supplied by the Research and Development Laboratory of the Owens-Corning Fiberglas Corp., Newark, Ohio. It was prepared from scrap platinum. After dissolving in aqua regia and evaporating almost to dryness, the solution was worked up several times with concentrated HC1. The resultant platinic chloride was diluted considerably, and metallic zinc was added, which precipitated the platinum in a very finely divided form. After dissolving the

Jan 1, 1949

By A M. Sardo, D E. Sinnett

This study uses the Q Method to examine how those living in former metal mining landscapes value this heritage and their preferences for the long-term management of mine waste. Such sites are often perceived as derelict or degraded, and of very little value. It is therefore assumed that their reuse, for example for development or recovery of metals, is likely to be beneficial. There are around 5,000 former metal mines in England and Wales, many of which are protected for their ecological, geological or cultural value. The Q Method is particularly suitable for issues where there is no consensus of opinion. We asked 38 residents of six mining areas in England and Wales to ‘sort’ a series of statements based on their resonance with the resident’s perspective; this is the Q sort. The statements covered a range of opinions of the mining legacy, its value and options for its management with a particular focus on the potential for metal recovery from the wastes. Analysis of the Q sorts revealed five perspectives on the mining heritage. All placed a high value on the cultural and ecological value of this heritage, however, they differed in their priorities for long-term management. For example, emphasis was placed on either nature conservation, cultural heritage, water quality or the opportunity for job creation through reworking the mines. Cutting across these themes there were also differing perspectives on the role of experts and local people in shaping the future management of the wastes. This research suggests that the views of local people are nuanced; they value their mining heritage but opinion is split on the most effective way to manage these sites especially where there is an impact on water quality.CITATION:Sinnett, D E and Sardo, A M, 2018. Former metal mining areas in England and Wales – local residents’ preferences for the management of wastes, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 126–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By A McCallum, J Abols, G Patrick, G Johansen

The authors challenge the traditional thinking that whole ore cyanidation followed by Carbon in Pulp (CIP) or Carbon in Leach (CIL) should be applied as a standard process in the majority of gold processing flow sheets. The concept of whole ore leaching by using cyanide can result in unnecessary environmental and capital risk. Alternative, currently available technologies can be used to provide the desired level of gold recovery at a much lower installed cost and less impact on the environment. Gravity concentration, alone or in conjunction with flotation, can produce a gold bearing concentrate that can then be fed directly to a batch or continuous intensive cyanidation unit. The In-line Leach Reactor (ILR) is an intensive cyanidation unit developed by Gekko Systems of Australia. Advantages of this technology include significantly reduced capital outlays for greenfield plants or plant upgrades and increased investor returns. Reduction of onsite cyanide and carbon inventories improves plant safety, materials handling and site security. By using direct electrowinning to treat the gold bearing solutions produced by the ILR, the need for a conventional carbon stripping circuit is removed. Potential also exists to increase grind size û saving energy, further reducing capital and operating costs and decreasing the environmental impact of a mill. Detoxification of cyanide before the release of solution to the tailings dam can minimise tailings disposal and containment requirements. When used in the right application the proposed process will have little or no impact on gold recovery and may actually increase recovery for complex ores. Areas applicable to this type of treatment include: plants in environmentally sensitive regions, lower tonnage higher grade deposits, coarse gold deposits, and preg robbing ores û some of which may not currently be economically feasible using standard processes and flow sheets. We have provided two examples of such projects, where an alternative to whole ore leach and CIP or CIL has the potential to deliver these benefits.

Jan 1, 2004

By Robert J. Anderson

"Introductory Statement:In melting the nonferrous metals and alloys for foundry and rolling-mill work, even with the best practice, there is always a loss, due principally to oxidation. Melting losses are a serious source of financial loss in brass and bronze practice, but they are especially serious in the case of aluminum and its light alloys because of the relatively high price of aluminum. The indications are that the melting losses in many aluminum foundries of the United States are at times high, and in some plants (especially where certain furnaces are used) they are entirely too high when compared with the average practice. The fact that the oxidation losses in melting aluminum and its light alloys are high is well known, but it is doubtful whether the factors governing the most suitable methods of melting for a minimum of dross are equally well known. The metal losses involved in melting are worthy of especial attention now because of the rapidly growing importance of the aluminum industry.Factors in the operation of furnaces which affect metal and fuel losses:The essential requirements in the commercial melting of any metal or alloy are that the melting losses should be low, the melting should be rapid, and the melting cost should be low. Certainly it may not be possible to obtain these requirements in any furnace selected at random, and it follows that the design and the operation of furnaces for melting different metals are subjects that warrant the most extensive study and tests. As a general rule, in the industrial operation of furnaces, run on aluminum and aluminum alloys, an effort is made to keep the dross and oxidation losses as low as possible. In attempting to hold dross losses low, numerous factors involved in metal melting may be overlooked, or at least disregarded, and the net practical result may be that the furnace is exceedingly wasteful of fuel. In the case of aluminum and its light alloys, the effect of increasing the temperature of melting, at least in an atmosphere containing free oxygen and nitrogen, is to increase the net melting loss."

Apr 1, 1921

By C. L. Lin

A PC image-based on-line coarse particle size analyzer has been developed to measure particle size distributions under plant situations where overlapped particles are being transported on a moving belt conveyor. Although previous testing had shown satisfactory performance of this image-based system for separated particle size measurements (the non-overlapped case), it was necessary to modify original algorithms in order to solve the overlap problem and make the system suitable for plant operations. On-site testing has been conducted at a large copper concentrator in the southwestern U.S. for further investigation of the overlap problem.

Jan 1, 1995

By Yi Luo, Jian Yang

Subsurface strata movements and deformations associated with longwall mining operations in underground coal mines could cause various disturbances to subsurface mine structures, ground water bodies, and coalbed methane reservoirs. In order to assess those disturbances correctly and to design effective and efficient mitigation measures, it is necessary to develop an accurate prediction model for subsurface strata movements and deformations. Decades of research have demonstrated that variations of stratification and lithology in the overburden have significant influence on the subsurface strata movements and deformations during ground subsidence process. The key strata theory states that the thick and hard key strata serve as the backbone of the overburden and control the movements of the thin and soft weak strata located above them. From an engineering standpoint, the overburden strata are subdivided into several individual groups by the key strata with each group consisting of a key layer at the bottom and weak layers overlying it. A new subsurface subsidence prediction model considering the key strata effects on subsurface strata movements and deformations has been proposed. In this method, elastic modulus, specific weight, tensile strength, and uniaxial compressive strength (UCS) of each layer are used to identify the key layers and to determine the needed subsurface subsidence parameters. The influence function method, proven to be accurate and versatile for surface subsidence prediction, was employed to predict the subsidence on each of the overburden layers from mining horizon progressively upward to ground surface with the assumption that the predicted subsidence on a given layer serves as the subsidence source for the layer immediately above. The enhanced subsurface subsidence prediction model has been demonstrated with an actual case to show its applicability and improvement.

Jan 25, 2021

By S. Deonarain, L. S. Schultz

"This paper details the process and methodology followed to rehabilitate a rectangular ventilation shaft, situated in the Free State region of the Witwatersrand Gold Fields in South Africa. The shaft consists of seven compartments where self-mining of the sidewalls had taken place and damage to the decayed steel work in the shaft had taken place, thus limiting access down the shaft. The paper will provide some insight into the successes and challenges encountered during the project and may provide some learnings for future projects of a similar nature. INTRODUCTION The ventilation shaft forms part of the Phakisa Mine, situated in the Welkom area of the Free State province of South Africa, and is located in the Southern part of the Witwatersrand Basin, one of the world’s largest known and richest gold deposits (Figure 1).As is typical in South African gold mines situated in the Witwatersrand basin, the shaft is 1 770 metres deep (below collar). The shaft was sunk during the early 1940’s and comprised a rectangular shape with 7 compartments, used for both rock hoisting and men and material winding, respectively, with a single lift “Mary-Anne” compartment. Early in 2003, the mine decided to change the shaft from a downcast hoisting shaft to an up-cast ventilation shaft. The conveyances, ropes, winders and headgear (head frame) were removed and replaced with a high volume fan delivering 323m³/s of air at a pressure of 4.2Pa on surface. The up-cast velocity in the shaft was 6.5m/s, however this reduced significantly with the scaling of the shaft and the restrictions at shaft bottom. Although Harmony had converted the shaft from a downcast service shaft to an up-cast ventilation shaft some years back, the shaft steel work in the barrel of the shaft was left intact. Over the years, the steelwork in the shaft had decayed (rust and grime) and portions of this steelwork fell down the shaft. Concurrent with the decaying steel work, portions of the shaft lining had collapsed and it was getting progressively worse."

Jan 1, 2019

By E. A. Gulbransen, K. F. Andrew

In a recent communication14 we have reported on the kinetics of the reactions of zirconium with O2, N2 and H2 as a function of the time, temperature and pressure variables. A systematic study was made and the results correlated with fundamental theories of gas-metal reactions. This paper will present a similar study for titanium. Titanium and zirconium are members of the IV group of the periodic table and possess many similar physical and chemical properties as a result of their similar electronic configuration for the outer electrons. The two metals are relatively inert to both gas and liquid phase corrosion at room temperature. However, at moderate temperatures the metals become active and react readily with the common gases including O2, N2 and H2 which are of interest in this study. A study of the kinetics of these gas-metal reactions is of interest for three reasons: (1) to understand the rate of reaction of titanium and its role in the behavior of high temperature alloys; (2) to understand the practical difficulties of the reduction, refining and working of titanium; and (3) to correlate the data with fundamental theories of gas-metal reactions and crystal structure predictions. Literature Survey Several review papers8 and books4243 exist on the preparation and properties of titanium and its alloys. THE METAL Titanium has, at room temperature, a hexagonal lattice of the zinc type. Hagg19 gives a value of 2.953A for the (a) axis, a value of 4.729 for the (c) axis and a density of 4.427 at 20°C. Burgers and Jacobs6 have observed the transformation of the hexagonal to the body-centered cubic structure at 880°C and have established a value of 3.31 for the cube edge and a density of 4.31. TITANIUM-OXYGEN Carpenter and Reavell6 using a pressure change method have studied the reaction at temperatures of 742° and 1000°C and for a pressure of one-fifth of an atmosphere. The probabilities for reaction are calculated from kinetic theory and they report a value of 10-5 for O2 at 1000°C and 10-6 at 740°C. The titanium-oxygen system has been investigated by Ehrlich.10,11 Five phases are observed. Between (TiO2 and TiO1.90) an alpha-phase, consisting ofarutile lattice, is found. A beta-phase is observed between (TiO1.80 and TiO1.70). A gamma-phase is homogeneous between (TiO1.56 and TiO1.46) and has a structure of the corundum type. The delta-phase exists between TiO1.25 and TiO0.6 and has a sodium chloride structure. From TiO0.42 to Ti the metal structure is observed. The surface oxide films have been studied by Hickman and Gulbransen.20 The rutile structure is observed in the temperature range studied, 300 to 700°C. Three crystalline modifications of TiO2 exist: rutile and anatase which are tetragonal and brookite which has an orthorhombic structure. Anatase is reported36 to exist in two forms: I and II. Anatase II changes to anatase I at 642°C. Anatase I is stable up to 915°C where rutile becomes the stable modification. At 1300°C rutile transforms to brookite which melts at 1900°C. The monoxide, TiO, may be prepared from the dioxide by high temperature reduction with carbon or magnesium. Its melting point is 1750°C. TITANIUM-NITROGEN Carpenter and Reavell6 report that at 1000°C a linear rate law is observed. The probability of reaction is given as 10-8 at 1000°C. Fast12 has studied the solubility of nitrogen and its effect on the mechanical properties of the metal. The crystal structure of TiN has been shown by several workers2'21'44 to follow the sodium chloride structure. However, the calculated density is found to differ from the pycnometric value. This is studied by Brager3,4 in detail. He has suggested that the titanium sites in the lattice are only partially filled at low temperatures. As the temperature of preparation is raised the vacant sites become occupied which expands the lattice and increases the hardness and density. An (a) value of 4.22Å is given for room temperature. TITANIUM-HYDROGEN The solubility and the crystal structures observed in this system have been reviewed in a recent book by Smith.40

Jan 1, 1950

The Library of the above-named Societies is open from 9 A.M. to 9 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M.. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information-will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries: All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute. can be of service to the Library by forwarding copies of mining-reports, maps privately issued, and similar material, which will he classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 5, 1913

By M. K. McMullen

Mineral Development Agreements (MDA?s) are a cooperative mechanism in Canada by which the federal and individual provincial governments can coordinate their scientific, techno- logical and market development resources in order to implement measures designed to stimulate mineral exploration and development by the private sector; the objective, ultimately, being to increase the mineral industry?s contribution to provincial economies. In the latest round of MDA?s, which was initiated in 1984, a significant number of planned activities relate to industrial minerals. This paper will describe the nature and importance of MDA's in Canada and will outline the wide range of activities taking place with respect to industrial minerals.

Jan 1, 1987

By Stanley I. M, Brett D, Dickson R

The Mt Lyell Mine, situated in Queenstown on the west coast of Tasmania, has a production history of more than 100 years. Previous mining activities have resulted in substantial modifications to environmental conditions at Mt Lyell and disposal of sulphidic waste rock across the lease has left a legacy of on-going environmental impacts including acid drainage (AD). In 1995 Copper Mines of Tasmania (CMT) was granted a mining lease Irons the Tasmanian State Government for redevelopment of Mt Lyell and indemnity from actions concerning pollution from previous occupation and use of leased land. The Environmental Management Plan (EMP) for the Mt Lyell redevelopment committed CMT to be responsible for waste rock dumps generated from their activities and to ensure that management is in-line with best practice environmental management principles. CMT commenced commercial production in December 1995 with sulphidic material from development of the underground Prince Lyell mine reporting to a single waste rock dump constructed according to a management plan developed in July 1995 and superseded by a management plan for extension in May 1997. The CMT waste rock dump currently has a total capacity of 220 000 m- and approximately 120 000 m3 of rock have been placed to-date. Material reporting to the dump is placed in a densely compacted state to a controlled surface profile. The dump is clay capped and a final revegetated soil layer placed on top. A rock pitched drain extends down to a wetland area in order to remove stormwater and minimise possible soil erosion on the revegetated sections. An integral part of the management plan for the waste rock dump involves characterisation of waste rock to identify geochemical rock types according to acid forming potential with provision for selective placement within the dump. High-risk materials are selectively placed and covered within the core of the waste rock dump, where possible, to control sulphide oxidation. Monitoring equipment has been installed in the waste rock dump by the Australian Nuclear Science and Technology Organisation (ANSTO) and an on-going monitoring program has been established to demonstrate the integrity of the dump cover as a barrier to the influx of atmospheric oxygen into the dump. The overall objectives of this program of work are to control the oxidation of sulphidic waste rock in the waste rock dump, minimise the risk of AD, prevent pollution of the aquatic environment and thereby demonstrate the integrity of the CMT waste rock dump management Strategy.

Jan 1, 1997

By Diniz Ramos de Lima Júnior

Dentro das refinarias os tanques de armazenamento desempenham um papel fundamental, pois armazenam matéria prima para abastecimento das unidades, produtos intermediários entre os processos e produtos finais para distribuição. O presente trabalho apresenta de modo comparativo as características mecânicas e microestruturais da zona termicamente afetada de juntas soldadas formadas pelos processos de soldagem com Arame Tubular (FCAW) e Eletrodo Revestido (SMAW) aplicados na fabricação e reparo de tanques de armazenamento utilizados na indústria de petróleo. Os procedimentos de soldagem para cada junta soldada seguiram EPS (Especificação do Procedimento de Soldagem) utilizada por uma empresa que fabrica e repara tanques de armazenamento para indústrias de petróleo. O metal de base utilizado foi o aço estrutural de classificação ASTM A-36 em geometria plana e com chanfro tipo K. A solda foi multipasses de topo na posição horizontal (2G). Para realização deste estudo foram realizados quatro tipos de ensaios destrutivos: tração, microdureza Vickers, impacto Charpy e metalográfia. Os resultados indicaram a importância da seleção do processo de soldagem em termos de produção e formação da junta soldada e uma heterogeneidade devido as diferentes microestruturas presentes nas zonas termicamente afetadas que demostraram grande influência no perfil de microdureza.

Aug 8, 2018