Search Documents

By Will H. Coghill

The jig men of the Tri-State (Joplin-Miami) zinc district complain about the flakiness of their mill feed. They believe that the flakiness of the composite grains of gangue and mineral are to blame for losses of zinc; that is, that the flaky grains in the jig tailings have higher zinc tenor than the cubical grains. Although the evidence which follows contradicts this belief, no effort is made to give a final and conclusive answer. On the other hand, there is outlined a positive and mechanical method which the operator may use to pursue this and similar investigations. DISCUSSION OF SCREENING METHOD Hand-sorting is obviously not satisfactory for separating cubical grains from flaky grains because the personal influence can not be removed. Screens, however, may be used with success. A set of each of two types of screens is required; namely, the square-hole type and the rectangular (rectang, oblong) type. The square-hole screens must be of the double Tyler scale; that is, the order of the sieves should be after the fourth root of two instead of the customary square root of two; close sizing is important. The size of the rectang screens may be selected by trials so that a part of the material already closely sized on the square-hole screens, will pass the oblong holes. Obviously, the cubical grains will remain on the rectang and the flaky grains will pass through. Hence the mode of operation is to screen first on square-hole screens and then split the products on the oblong-hole screens.

Jan 1, 1928

By J-S. Marois, F. Cappucitti, Y. Dodier, D. Downey, G. Matton

"The flotation processes of the Niobec Mine have been affected by a seasonal loss of recovery and a significant increase in reagent consumption over the past few winters. This paper discusses the problem-solving methodology that was used to identify the root causes, to develop solutions and to implement changes that resolved the problem to restore the process to summer-like conditions year-round. Mainly, it was found that the process water was contaminated by phosphates ions, which adversely affected the carbonate pre-flotation, and caused detrimental effects on the subsequent niobium flotation. The phosphate ions were being generated by the process itself, but were consumed by algae in summer conditions. It was determined in laboratory studies that concentrations as low as 5 ppm were enough to affect the circuit and that the multiple additions of process water throughout the circuit was worsening the effect. Also, temperature was found to have an impact on the reagent performance. The performance of the plant was restored by implementing a natural treatment of our process water with a simple cost-free rearrangement of our circuit streams. In addition to that, our extensive geometallurgical program was used to provide ore to the plant restricting phosphate generation in the process. Also, a modification of the collector was developed and introduced in the carbonate pre-flotation that provided improved performance during the periods of low pulp temperature.INTRODUCTION Niobec is one the three major global producers of niobium presently in operation. Situated in the Saguenay-Lac-St-Jean region of Quebec and in operation since 1976, the site produces ferroniobium (FeNb) to be used mainly in High Strength Low Alloy (HSLA) steel, which is known to have better mechanical properties than carbon steel. The Niobec operation consists of an underground mine, a concentrator and a converter plant. The concentrator concentrates niobium-bearing minerals, mainly pyrochlore and columbite, to produce a high-content Nb2O5 concentrate which is then converted to FeNb in the converter plant by an aluminothermic reaction. The Niobec concentrator flowsheet, which has gone through many expansions and optimisation over the years, consists of grinding, desliming, flotation and leaching steps. The flotation steps are numerous, sensitive and difficult to operate due to the non-selective nature of oxide mineral collectors. Thus, the pyrochlore concentration process at Niobec still faces many challenges and is constantly going through periods of continuous improvement."

Jan 1, 2018

By Zhang Yongzhu

In hydrometallurgical processes of PGMs separation and refining, differences between 1-PGMs (Ru;Rh;Pd) and h-PGMs(Os;Ir;Pt) in thermodynamics and kinetics have been observed. The successful practice in the separation and refining of PGMs in China, is mainly based on the following two kinetically extraction sequences of: (1) for the extraction of PGMs complexes in different configurations with coordination mechanism (AuCI,) -> (MCl6)2-> (MCl4 )2-> (MCI6) 3- , and the substitution rate for h-PGMs complexes with higher effective nuclear charge Z' is much more slow than that of I-PGMs. and (2) for the extraction of PGMs in different configurations with oxonium (or ion -exchange) mechanism (AuCl4)-> (MCl4)2--> (MCl6)2-> (MCl6)3- and the extraction of h-PGMs complexes with low surface charge density is more fast than that of I-PGMs complexes. In view of atomic structure theory, the similarity of atomic radii and chemical properties and difficult separation of PGMs resulted from the Lanthanide Contruction between 5th period (1-PGMs) and 6th period (h-PGMs). The differences between h-PGMs and 1-PGMs are due to the loss shielding of 4f subshells on 5d electrons for h-PGMs with higher nuclear number, which makes h-PGMs have a higher Z' (effective nuclear charge) and strong attraction for outer space electrons. As a result, h-PGMs metals and complexes are thermodynamically more stable and kinetically more inert than the corresponding 1-PGMs. The differences between h-PGMs and 1 -PGMs in aspects of elements properties, complexes, hydration, substitution and redox reactions , are discussed.

Jan 1, 1993

The Gold Ridge Mine is an open-cut gold mine in the Solomon Islands. The mine is owned and operated by Gold Ridge Mining Limited, a wholly owned subsidiary of Ross Mining NL. At the invitation of the Solomon Island Government, project construction commenced in July 1997 and gold production commenced in August 1998. The mine is the countryÆs first, and represents a major milestone in the development of the Solomon Islands. At the time of project approval and construction, there was a growing awareness in the country of the potential impacts of mining in the tropics, partly due to unfavourable publicity surrounding a number of other mining operations in the Pacific region. The management of environmental impacts was therefore an important consideration in the approval of the project, and continues to receive a high level of attention from the Government and community. Ross Mining did not commit to the Gold Ridge Project until it had satisfied itself that all waste rock and tailings could be safely contained on-site, and that the standards normally expected of a mine in Australia could be met. Ross Mining approached the approval, construction, and operation of the Gold Ridge Mine with a set of operating principles that met Government and community concerns. These were:best practice environmental management; operation of the mine in accordance with standards expected of mining operations in Australia; independent peer review of key technical aspects; on-going consultation with Government and community; and equitable transfer of wealth to landowners and the local community. As a consequence, the Gold Ridge Mine has developed into a successful mining operation with a high level of support from local landowners, the general community and the Central and Provincial Governments of the Solomon Islands.

Jan 1, 1999

By Marcelo Marchesi Martinelli, Caio Henrique Vidigal

Gasômetros são equipamentos de grande valia para aumento da eficiência energética e ambiental de empresas siderúrgicas integradas, sendo estes equipamentos responsáveis pelo controle da pressão do gás resultante das transformações dos processos siderúrgicos, controle este realizado através das variações de volume abaixo dos pistões. Quando não há disponibilidade de operação dos gasômetros faz-se necessário o uso de torres de queima para controle das pressões das redes de gases. Em dezembro de dois mil e dezoito fora realizada a troca da selagem do gasômetro de gás de Coqueria da ArcelorMittal Tubarão, que utiliza a tecnologia M.A.N. (Selo a óleo). Utilizando técnicas da metodologia Lean, modificando o mindset e alterando antigos paradigmas foi possível realizar a manutenção, de forma eficaz, em 32 dias, 28 a menos que o último trabalho similar realizado e 13 dias a menos que a meta proposta para a parada, aumentando a recuperação de gás de Coqueria, maximizando ganhos de geração elétrica e minimizando a exposição a riscos ambientais associados a parada. As ideias apresentadas neste artigo são de grande valia para a evolução do pensamento crítico e sistêmico sobre a manutenção, não só em gasômetros, mas em todo o contexto de realização de atividades já consolidadas.

Aug 1, 2019

A real Dorothy Dix title has been selec- ted for this paper. It has the advantage, however, of being capable of being interpreted in many different ways and hence I can select my own approach. You probably are thinking that this topic would be more appropriately handled by an Accountant. I wish to make it clear at the outset that I am not skilled in the sometimes mysterious ways of Accountants - likewise that profession frequently has difficulty in pinning down economists. We have our own strange ideas about profits, marginal efficiencies, cost/benefit analysis etc. What follows is in the main a mixture of two disciplines, probably in a form that few of the purists from either side would accept. Nor do I expect the reader to accept my own prejudices. The paper is designed to stimulate thought and discussion'on the subject. Emotive words such as "profit" and "loss" make for wide differences of opinion. At the time of writing there is a surprising degree of acceptance of the viewpoint that profits in Australia are too low and one is tempted to make this point of near agreement a starting Point.

Jan 1, 1975

By Lars A. Bergstrom

High-voltage direct -current transmission is a relatively new technology. The successful development and operation of AC/DC converters, capable of handling large power blocks, have made HVDC transmission generally accepted by utility engineer s and planners around the world. HVDC technology still has significant development potential and, as a result, it is expected that equipment costs will escalate at a substantially slower rate than those of conventional AC equipment. This development will also result in still more compact terminal stations. This paper reviews two modern HVDC installations. In Zaire in Africa. a 1700-km overhead DC line rated at 500 kv, will supply power to the copper mining district in the Shaba region. Another HVDC link connects Norway and Denmark through a submarine cable rated at 250 kv. This is the longest HVDC cable in the world, 127 km, and the water depth , maximum 530 m, is also much greater than for any previous similar cable. The reasons for selecting HVDC are discussed, and the design and layouts are presented.

Jan 1, 1978

By Frank C. Morris

This report presents the results of a Bureau of Mines study to identify clays found in several petroleum-reservoir rocks in the Tejon-Grapevine area, Kern County, Calif., and to determine the effect of water sensitivity of the clays on the permeability of the reservoir rocks. The clays in the porous rocks were examined in detail, and the clay-mineral types were identified by differential thermal analysis, X-ray diffraction, and optical and dye-staining methods. Fresh-water damage to the permeability of the oil-reservoir rocks was indicated by a study of 125 core samples from productive formations. The study indicated that, although clays were generally less than 5 percent of the reservoir rocks, they swelled in water, particularly fresh water, and nearly blocked the flow channels through which oil flows to the well, effectively reducing the permeability of the formations. The average permeability of rock decreased from 1,600 millidarcys in air to 620 millidarcys in salt water and 120 millidarcys in fresh water. The dominant clays in the oil-bearing sandstones were members of the montmorillonite group. They were associated with smaller quantities of clays found to be in the mica or illite group. None of the cores appeared to contain clays of the kaolinite group. In the lower section of the J.V. sandstone indications of what appeared to be the mineral sepiolite were noted.

Jan 1, 1959

By Norman Paley, Finn Ouchterlony

Detailed fragmentation data for different blast delay timing tests at the Red Dog mine in Alaska are analyzed. This work is a continuation of previous work in which the crusher output was found to be better described by the three-parameter Swebrec function than by the Rosin-Rammler function. For a crusher model, the x50 variable sufficed to describe changing crusher input while b and xmax could be considered fixed. For the crusher output from aggregated stockpile rock, as measured by digital image analysis using Split-Online, the constancy of b was not as apparent. In this paper detailed stockpile data, single Split data series, and sieved belt cuts of crusher product are analyzed using the Swebrec and truncated Rosin-Rammler functions. The variability of b is confirmed. By using specific fraction passing sizes a shortcut is presented that removes the need to do curve fitting to determine the three Swebrec function parameters.

Jan 1, 2013

By Josh Swank

Albert Einstein once said, ?the important thing is not to stop questioning.? In the mining industry, a lack of inquisitiveness may lead to a blissful ignorance but it certainly will not increase efficiencies. While one may claim necessity is the mother of invention, questioning and analyzing how methods and systems can be improved is the catalyst to discovering necessities. Understandably, when working in the middle of Canada?s oil sands, where trucks operate around the clock every day of the year, it is nearly impossible to pull the nose from the grindstone long enough to provide thorough analysis. But, fortunately, some manufacturers/inventors have assisted by examining the process and the ensuing headaches within this application.

Jan 1, 2013

By Robert L. (Original by) Llewellyn

Many of the problems that occur in the preparation plant originate from practices in the mine. Impurities in raw coal can be in the seam itself or from extraneous material taken in mining from the roof or bottom. In the case of underground mines, the choice of mining equipment will affect the size consist and the amount of extraneous material included with the coal. Also, governmental regulations concerning the degree of rock dusting, gobbing underground, and cleanup have increased the dirt in raw coal. Sulfur dioxide emission standards, on the other hand, are pressuring the coal industry to clean coal more thoroughly. Coal supplied for coking purposes is nearly all upgraded by washing, while for the largest market, electric power generation, a high proportion is shipped as a raw product with processing, in whole or in part, only necessary when excess impurities are mined with the coal. This chapter will deal primarily with plants that process or wash coal to some extent (Fig. 1) and only incidentally with mines shipping raw run-of-mine coal crushed to a top size of, usually, 51 to 102 mm (2 to 4 in.), with little, if any, other treatment.

Jan 1, 1981

By H. Kenworthy

The objective of this investigation was to evaluate the technical feasibility of smelting certain low-grade domestic iron ores in an electric furnace. Laboratory-scale experiments showed that a high recovery of iron in the form of pig iron can be obtained from east Texas ores containing less than 25 percent iron. The pig iron was amenable to standard-or electric-furnace-refining methods for producing steel. Car-bon, silicon, and phosphorus were the primary impurities removed in refining. Overall recoveries of iron as pig iron exceeded 95 percent, in contrast with commercial mineral-dressing recoveries on these particular ores of 50 percent of the iron as a 45-to 50-percent iron concentrate.

Jan 1, 1958

By M I. Pownceby, S Hapugoda, H Han, V Nunna, L Lu

Charcoal produced from Syzygium Zeylanicum (local name: Yakada Maran = iron killer) trees were widely used in ancient Sri Lankan iron smelting practices. In this study, relict charcoal from Syzygium Zeylanicum tree trunks, branches and leaves were analysed for the first time. Unusually high concentrations of calcium oxalate (CaC2O4.H2O – CaOX) crystals were identified preserved in plant cell structures by optical mineralogy and SEM analysis. Thermogravimetric Analysis (TGA) of CaOX showed that it displayed three decomposition stages, releasing H2O at 177°C, CO at 493°C and CO2 at 750°C. Following the identification of CaOX in Sri Lankan charcoal, a series of reduction tests on a low-grade, high-P iron ore fine sample (high SiO2: 5 wt. per cent; Al2O3 4 wt. per cent; P: 0.135 wt. per cent) doped with CaOX were carried out at various temperatures. Samples were analysed by XRF, SEM and EPMA to determine the degree of reduction and the effect of reduction on the deportment of impurities, in particular P. Reduction tests at 800°C and 900°C with 5 wt. per cent CaOX showed that the reducibility increased to over 65 per cent. At temperatures above 900°C, P was located mainly within a fine, interstitial glass matrix suggesting that the CaOX flux enhanced removal of P from iron-rich pre-cursor phases to form glass. Preliminary magnetic separation tests to remove the P-rich interstitial glass were unsuccessful due to the fine grain size. Further complete reduction tests at temperatures above 1200°C with addition of coke to convert the iron oxides into Fem were conducted with samples doped with 10 wt. per cent CaOX, 10 wt. per cent CaCO3 and equivalent undoped samples. Results confirmed the preferential P-incorporation into a glassy matrix in the CaOX samples although some rare P incorporation into the metallic phase was noted. Experimental results, including comparisons with the CaCO3 fluxed and undoped samples, are discussed in view of the potential for CaOX flux for removing P (and potentially other impurities) from P-rich iron ores.

Nov 8, 2021

By C. S. Lord

"AbstractThe slow progress of conventional geological reconnaissance of the northern Canadian Shield during the past twenty years clearly indicates the need for a radically new field technique. Operation Keewatin, involving the use of helicopters as the traversing vehicles, was planned and executed by the Geological Survey of Canada in response to this requirement.About 57,000 square miles of District of Keewatin, N.W.T., were mapped during the 1952 field season in appropriate detail for publication at 1 inch to 8 miles. The Operation disclosed about 14,100 square miles of Precambrian sedimentary and volcanic rocks ranging in •age from Archaean to Late Proterozoic. About 7,700 square miles of this area are underlain by greenstone. This work was accomplished in a field season of 113 days, including the spring break-up. Routine aerial geological observations were made from two helicopters flying about 300 feet above the ground; these observations were checked by more than 1,700 landings and about an equal number of aerial observations from heights of less than 50 feet. Logistical support was •provided by a Norseman aircraft on skiis or floats. Combined helicopter and Norseman flying time was about 990 hours. More than 1-00 square miles were mapped per helicopter-hour, and about 815 square miles were examined each day that both helicopters operated. The reconnaissance cost about $207,000, or $3.63 per square mile mapped.As a result of this trial use of helicopters there is now available a reasonably proven method whereby an acceptable geological reconnaissance of the barren grounds of the Canadian .Shield within the Districts of Keewatin and Mackenzie might be completed within a decade. Thus, within a few years, it could place at the disposal of the prospecting and mining fraternity data which, by conventional methods, might not be made available to this generation. Due weight must be accorded this time factor when evaluating the aerial technique."

Jan 1, 1953

By Paul D. Tomlingson

The difficult and often harsh working environment of the mining industry can stress both personnel and equipment to the extreme. Often, the unintended consequences of this environment lead to confrontations between departments, as each goes about its tasks of mining, maintaining or supporting these activities. On occasion, the confrontations may result in criticism of other departments for perceived or real sins or omissions. The offended department may not be able to change the circumstances, but can only complain while frustration persists. The most effective solutions are the actions of the mine manager. By establishing mutually supporting roles of each department and specifying conditions for the interactive conduct of maintenance, the mine manager can better assure that the inherent problems of the mining environment are neutralized.

Jan 1, 2011

By Leonard Kellogg

Introduction The Mine Manager or Superintendent is a man faced with a difficult problem. He must direct the activities of his mine in such a manner that, over a period of time, the greatest possible profit will be realized. In this respect, a mine is no different from any other business organized for profit. What makes the mine manager's task so difficult then? The profit of a mine is determined by -among other things -the grade of ore, the market price of the metal or metals produced, and the cost to operate the mine. The mine manager cannot do much about the first two of these, but he has considerable control over the operating cost. This cost will depend in large measure on the nature of the programme on which he plans to operate his mine. This operating plan may be broad or specific, on a long-range basis or on a month to month basis. The development of the plan, however, is made very difficult by the existence of so many factors which must be considered. These may be (1) factors requiring decisions based on the best judgment and interpretation of engineering and geological information available, or (2) items which must be considered but which are largely non-controllable. To be more specific, examples of such items would be: (1).-(a) The amount and type of development work to be done in relation to amount of ore to be mined. (b) Mining methods to be followed and type of equipment to be used. © Amount of exploration diamond drilling to be done if the orebody is not clearly defined. (2).-(a) Rock type and degree of hardness. (b) Width, depth, and pitch of veins. © Amount of work requiring timbering. (d) Faults encountered. (e) Water and gas conditions met with.

Jan 1, 1952

By R. L. Loofbourow

The adjacent towns of Rouyn and Noranda, centers of the Rouyn mining district of western Quebec, are 360 miles by air line almost duo north of Toronto. Rouyn is reached from the main lines of the Canadian National Railways and the Canadian Pacific Railway at North Bay, Ontario, by the Temiskaming & Northern Ontario Railway and its subsidiary, the Nipissing Central Railway. Noranda is the southwestern terminus of a branch from the Canadian National Railway between Winnipeg and Quebec. The Rouyn mining district is a part of a mineralized zone that has been traced for a distance of 140 miles from Kirkland Lake in Ontario eastward into the Province of Quebec to the Pascalis district. From Rouyn the mine is 5 miler almost duo south over a gravel rend built by the company with assistance from the Province of Quebec.

Jan 1, 1933

By K. H. Poulsen, C. J. . Hodgson

Synvolcanic, layered gabbro-anorthosite sills at Rainy Lake, Northwestern Ontario, reflect a combination of igneous processes including fractional crystallization, wall rock assimilation and possibly liquid immiscibility. Chalcopyrite-pyrrhotite mineralization at the base of the Grassy Portage intrusion accumulated by crystallization of a sulphide liquid during cooling. Upward enrichment of Fe and Ti in this intrusion and also in the Bad Vermilion Lake anorthosite complex culminated with the crystallization of lenses of disseminated to massive magnetite+ apatite+ ilmenite+ rutile. Regional low to medium grade metamorphism and accompanying deformation resulted in recrystallization and local remobilization of ore minerals.

Jan 1, 1984

By Robert Smith

Deposits are global, said Barrick Gold's Smith. This means that the mineral industry, by necessity, is global. "Manufacturers have considerable freedom to decide exactly where they wish to produce whatever it is that they sell," he said. "What we sell, on the other hand, must be produced where nature chose to lay it down. The question is not so much, whether to go global, as when to do it and how to go about it." The timing of international expansion depends on external factors, often political, Smith said, and on internal ones that relate to the company's size and stage of development. "In deciding how to expand, a company is largely deciding how to adapt its existing business strategy to activity on the world stage," he said Barrick entered 1997 with 1.58 kt (51 million oz) of reserves, Smith said, annual production of 93.3 t (3 mil- lion oz) and cash flow of $463 million. Reserves in- creased 40% in 1996 and production will begin to rise again significantly in 1999. "We believe our fundamental strategy is responsible for our early development and subsequent success," he said. Barrick entered the gold-mining industry in 1983. Its corporate mandate was to create shareholder value, Smith said. From the beginning, the company took a different approach - businesslike, entrepreneurial, strategic and focused. "Many mining companies start out with a technical team and develop business and financial expertise thereafter," Smith said. "In 1983, Barrick had the business people, and then moved into mining." First, it acquired part interest in two small operations, one in Alaska and one in Ontario. Then, in 1984, it merged with Camflo Mines, which operated a low-cost underground operation in Quebec.

Jan 1, 1997

By Larissa Rodrigues de Carvalho Rocha, Mauro Vivaldino Fernandes, Beatriz Fausta Gandra

A composição química do gás redutor afeta, de forma marcante, sua difusividade através do leito e a capacidade de redução da carga metálica. Associado a isto, o cenário econômico e ambiental indica a necessidade de se buscar cada vez mais elevada produtividade dos altos-fornos, com baixo consumo de combustível e menor emissão de CO2. Para tanto, as empresas têm buscado operar com elevada taxa de injeção de carvão e, em casos de política favorável, intensificar o uso de gás natural em altos-fornos. Nestes casos, a quantidade de material reduzida via H2, em comparação ao CO, é aumentada. No presente trabalho, são apresentados os resultados de ensaios em amolecimento e fusão (A&F) de dois tipos de granulados, de um tipo de pelota e de um sínter industrial, utilizando-se como redutor um gás com diferentes teores de H2 (0% a 12%). Verificou-se que, para o granulado, não há uma tendência definida. Embora um maior teor de hidrogênio possa favorecer a redução, isto não refletiu em melhor permeabilidade do leito. No caso da pelota estudada, houve leve tendência de melhora nos parâmetros avaliados quando se tem o gás mais rico em hidrogênio. No entanto, seu desempenho em A&F foi muito aquém daquele esperado para este tipo de carga, uma vez que apresentou elevada resistência à permeabilidade associada à baixa redutibilidade até o início do amolecimento. Para o sínter, foi identificada evidente melhora nos aspectos de redução e de permeabilidade do leito.

Oct 1, 2019