Search Documents

By Racquel Nottingham, Freddy Lopez, Ole Gadermann

The ongoing urban development is a global phenomenon, placing has high demands on urban infrastructure (housing, public services, transportation, telecommunications, etc.). Micropiling is one of the most successfully implemented deep foundation technologies in urban interventions, and in densely populated and built-up areas. The use of micropiles enabled the implementation of several solutions within short time frames, with minimal disturbance to the daily activities of the population. Since urban interventions usually represent a very important investment and have an economic impact, special attention should be paid to the serviceability of the urban infrastructure in the middle and long term. For the foundations, the design loadbearing capacity of the used structural elements needs to be guaranteed during the planned life time of the structures. In the case of micropiles, it must be ensured that the steel load bearing elements are effectively protected against corrosion. This paper presents the structural design of permanent self-drilling micropiles, subject to tension due to uplift loads. For the case study, different micropile systems - available worldwide - will also be evaluated. For the afore mentioned micropile systems, the design considerations regarding the durability of the reinforcement, based on their corrosion protection approaches, will be presented in this paper.

By Steven G. Grannes

This U.S. Bureau of Mines report summarizes Federal mandatory belt conveyor automatic fire suppression system installation requirements and inspection procedures, identifies system failure modes observed during in-mine investigations, and suggests system design and maintenance upgrades which, if implemented, would result in an improvement in overall system reliability. This report is a compilation of recommendations based on discussions with Mine Safety and Health Administration (MSHA) inspectors, review of manufacturer's literature, discussions with mine personnel, and research investigations of automatic fire suppression system performance in the laboratory and in mines. The Code of Federal Regulations (CFR) requirements for installation, inspection, and maintenance of fire suppression systems should be regarded as minimum standards.

Jan 1, 1990

By John P. Capp

The feasibility of simultaneously burning several paths through a coalbed to develop a multiple path underground gasification system was investigated by the Bureau of Mines during two experiments, Boreholes were drilled through the overburden and into the coal and arranged in a circle approximately 50 feet from a central borehole. In the first experiment, in an area which had previously been hydraulically fractured,5 air was injected at the center borehole. The coal was ignited at the other boreholes and the fire fronts traveled toward the center, counter to the flow of air, to backward burn paths through the coalbed. Two paths were linked during the first 5 days of operation. The outlets of these two paths were throttled and air pressure was increased to maintain the flow of air, but no other linkages were made. Fourteen days after the two linkages these two paths were opened and gasification was carried on for 10 days, but with only moderate success. In an effort to overcome operating difficulties air was injected at the peripheral boreholes, and the gases were drawn off at the center borehole. Reversed flow operations continued for 12 days and two more paths linked. The heating value of the gas generally was higher than 100 British thermal units per standard cubic foot (B.t.u. per std. c.f.). Because only four of seven paths linked, however, the entire system could not be evaluated with respect to product-gas output and recovery of energy.

Jan 1, 1961

By Mariano Iberico Miranda

El presente texto señala el proyecto minero San Marino. Este unidad es propiedad de la Cía. Minera "El barón" y se ubica en el distrito de San Mateo, provincia de Huarochirí, Lima. Asimismo comprende la geología, reservas, sistema de minado (método de explotación, laneamiento Y sistema de minado propuesto.

Sep 1, 1980

By David Montgomery

The feasibility of building a calibrator for the DuPont D-100 audio dosimeter is discussed. The desired specifications are used as guidelines but the possibility of their relaxation is also considered. Commercially available equipment is surveyed and found to not satisfy the guidelines. Several alternate concepts are investigated, and recommendations for further work are presented.

Jan 1, 1974

No paper available.

Jan 1, 1996

By S. Hopkins, J. Nolan, S. Gillis

"Cast in place concrete shaft linings have been used in many salt and potash shafts sunk in North America over the last 100 years. A large number of these shafts have exceeded their initial design lives and as producers look to extend the life of their operational assets, maintenance costs and shaft downtime will, in many cases, continue to rise unless repair work is undertaken. Successfully implementing concrete liner repair schemes in operating salt and potash shafts is complicated due to their age, environment and time constraints during inspection, detailed design and construction. This paper outlines a general approach to the repair of concrete-lined portions of these shafts, based on lessons learned from the authors’ involvement in a recent repair project. INTRODUCTION Prior to the recent boom in potash mine construction many of North America’s potash mine shafts were entering their sixth continuous decade of production (Table 1). Of North America’s salt mines, one has been in continuous production, for nearly nine decades.As would be expected, considering the environment in which these liners operate and the age of the material, the concrete-lined sections of the shafts outlined in Table 1 have been noted by the authors to have lost both cross-sectional thickness and strength over time. Since construction, three principal factors have contributed to this loss in section/strength; (1) physical degradation (impact, freeze/thaw or rebar expansion), (2) chemical degradation from brine/water inflows (Neville 1969; Bothwell, 1972) and (3) overstressing of the liner. These factors may act in combination, in which case they can produce more significant distress than individually. Physical degradation There are three main causes of physical degradation of concrete shaft liners. The first is impact from falling debris/tools or equipment (whether large or small), which may damage specific sections of concrete lining as they fall through the shaft. Impacts tend to damage infrastructure fixed to the shaft liner more than the liner itself, so damage from this mode of failure is usually localised, for example, where bolts fixing a shaft services bracket to the wall have been pulled away, pulling out the concrete around the bolts with them."

Jan 1, 2019

By Filippo Maria Leoni, Alessandro Bertero, Gianluca Pianezze

"As part of the Southeast Louisiana (SELA) drainage program, designed by the U.S. Army Corps of Engineers (USACE) to reduce flood damages in the City of New Orleans and surrounding parishes through the construction of new pumping stations and better drainage canals, the SELA-22 project entailed the installation of a concrete covered canal along Jefferson Ave. and Prytania Street, in a highly urbanized portion of Uptown New Orleans, LA. The scope of the required soil improvement was to replace the soil between two parallel lines of sheet piles with a soil-cement mass to eliminate underseepage and provide structural support for the concrete culvert. The USACE selected the jet grouting (Jet Grout) technology for the construction of the bottom plug. The bottom plug is between 18 and 21.5 ft thick with a maximum depth of approximately 40 ft, for a total length of approximately one mile. The treated soil comprised soft clays and silts with occasional presence of sands. Project specifications required 100% area coverage, a 28-days unconfined compressive strength of 100 psi and hydraulic conductivity of 1x10-6 cm/s, to be verified by testing specimens from cored samples. The specialty geotechnical contractor proposed to accomplish the task utilizing their proprietary and innovative elliptical bi-fluid Jet Grout technology, and elected to perform a pre-construction bench scale laboratory mixing program to determine the most suitable grout mix features (i.e. binder type and proportions, binder content, etc.) to be applied in the subsequent field test and production stages. This paper will summarize and compare the results obtained from the different pre-construction and construction stages; interpretations of the data will be provided, along with general considerations regarding the effectiveness and significance of bench scale testing for jet grouting applications.INTRODUCTIONIn general, the effectiveness of the construction parameters in any ground improvement work depends largely on the physical and mechanical properties of the soil to be treated. Therefore, well designed laboratory and field test programs, aimed to disclose the interaction between the site-specific soils and the mixing parameters, are essential to achieve the desired end product."

Jan 1, 2016

By Raphael Trousselle, William Reisz

The blasting industry is now well into its second decade of commercial use of electronic detonators. As an increasing number of blasters are introduced to the technology, the benefits are becoming more widely monitored and accepted in many surface blasting operations. However, their use in underground applications is not yet as widely established. This is primarily due to the distinct cost dynamics and processes associated with underground lasting.

Jan 1, 2012

By C Dell

Hillgrove, situated on the New England plateau of New South Wales, is an area rich in history and resources. Key resources are predominantly antimony, gold and scheelite and the area surrounding the historical field is environmentally sensitive and topographically challenging. Since acquiring the Hillgrove leases, Straits Hillgrove Gold has undertaken a significant exploration program on these historical mining areas with the goal to return the field to production. This exploration program has enabled Straits to significantly increase the resource base and has subsequently enabled the planned redevelopment of Hillgrove to be realised. In October 2006, installation of mining infrastructure and the initial stripping of existing development had commenced. To successfully redevelop Hillgrove, Straits has had to adopt a highly mechanised, trackless, diesel mining operation which will see the production rate commence at an initial rate of 250 kt/a of ore from a narrow vein environment. This ore will be processed on site to produce antimony metal, gold bullion and a scheelite concentrate.

Jan 1, 2008

By W. W. Agey

As a result of a field examination made during the Bureau of Mines intensive manganese program, three lots of ore were procured from the famous old Paymaster District, 7 miles from Midway Wells, Imperial County, Calif. This district is an old producer and shipped approximately 10,000 tons of 45-percent manganese ore during World War I. A 2-ton lot of ore was taken of a Bureau engineer from the exposure of a small fissure vein in conglomerate on the Turtle Group of claims; 1 mile east of the Pacific Coast Manganese Corp. claims. The vein material consisted of manganese oxides, calcite, and quartz in fairly coarse association.

Jan 1, 1949

By F. Ebbutt

The copper-bearing waters now treated successfully at Britannia for the recovery of their copper content are almost entirely derived from what is known as the Fairview mine; this was the first extensive copper producer of the Britannia ore-bodies, and consisted of a number of almost parallel veins, carrying good copper values, the ore consisting of chalcopyrite and pyrite in a quartz gangue. These veins occur in what is known as the ?Britannia shear zone' (Schofield, S. J., G.S.C. Sum. Rept., 1918, Pt. B), developed for roughly five miles in a roof-pendant in the well-known Coast Range batholith. This .pendant is made up of Palxozoic rocks known as the 'Britannia Formation' (LeRoy, O.E., Portion of Main Coast of B.C. and Adjacent Islands; G.S.C. Memoir No. 996, 1908). These consist of dark carbonaceous slates, quartzites; and tuffs or basic flows, and within them are large quartz porphyry siJls. These Britannia rocks are sheared and altered, the resultant rock being a fissile quartz-sericite or quartz-chlorite schist. The mineralization invariably occurs in this chlorite schist, which in the more productive areas has mottles or blobs of chlorite developed. A narrow, though persistent, band of grey slate forms the footwall of the productive portions of the shear zone.

Jan 1, 1928

By Frank E. Chase

Retreat mining is one of the most hazardous operations conducted underground. One of the keys to miner safety and an efficient recovery of the reserves is to design adequately sized production pillars to prevent pillar squeezes, excessive pillar spalling, severe floor heave, roof falls, and pillar bumps. Currently, few pillar design approaches are available which consider the abutment pressures generated by the gob. The Bureau of Mines is developing a method called Analysis of Retreat Mining Pillar Stability (ARMPS) to aid in the design of retreating sections. Back analysis of 42 case studies indicates that ARMPS can be helpful in predicting stability during retreat mining operations.

Jan 1, 1993

By Frederick Jr. Prime

THE first catalogue of Geological Reports of the United States was prepared by Prof. O. C. Marsh, and published in the American Journal of Science and Arts for 1867, vol. xliii, second series. Since then the list has more than doubled, and it was thought that the publication of a new catalogue, brought down to date, would be useful to many of the members of the Institute of Mining Engineers. The compiler will be most thankful to have any omissions or inaccuracies in the list sent to him, to be published as a supplement in the next volume of the Transactions. Especially to have the correct title, number of pages, plates, and maps of any volume on the list to which an * is prefixed, as he has been unable to personally consult such works. A preliminary list was issued last February, which has been almost doubled by the kindness of many friends. The writer desires more especially to express the obligations he is under to the following gentlemen The Chief of Engineers, U. S. A.; Principal Dawson, Mr. G. M. Dawson, Drs. B. J. Harrington and T. Sterry Hunt, of Montreal; Mr. H. Engelmann, of La Salle, Ill.; Dr. F. V. Hayden and Prof. J. W. Powell, U. S. Department of the Interior ; Prof. E. W. Hilgard, University of California; Prof. Henry Y. Hind, Windsor, N. S.; Prof. C. H. Hitchcock, of Dartmouth College; Mr. Henry A. Holmes, State Librarian, Albany; Maj. Jed. Hotchkiss, Staunton, Va. ; Prof. W. C. Kerr, Raleigh, N. C.; Dr. J. S. Newberry, of Columbia College ; Prof. W. H. Pettee, of the University of Michigan ; Dr. Samuel H. Scudder, Prof. N. S. Shaler, and Prof. J. D. Whitney, of Harvard College ; Mr. Sanderson Smith and Prof. J. J. Stevenson, of New York ; Mr. Addison Van Name, of Yale College, and Lieut. Geo. M. Wheeler, U. S. Engineers. PHILADELPHIA, 907 Walnut Street, October 1st, 1879.

Jan 1, 1879

By Laurence D. Burke

The electrocatalytic behaviour of gold in aqueous media is surprisingly complex and a novel view of gold electrode surfaces is proposed to explain the observed electrochemical responses. The metal surface is considered as a chemically (or redox) modified electrode, with equilibrated, low energy, surface gold atoms functioning as a relatively inert support and low coverage, high energy, protruding gold atoms (or minute clusters of same) functioning as electrocatalytic redox mediators. The protruding atoms are viewed as surface active sites and the complex electrocatalytic behaviour is attributed to the basic instability of the mediators, the diversity (and poor control) of same, and the acid/base (or hydrolysis) behaviour of the oxidized states of the mediators. It is assumed that major advances in the application of gold in the heterogeneous catalysis of gas phase reactions will be accompanied by similar advances in the use of gold in the electrocatalysis area; however, this will require considerable work of both a practical and theoretical nature.

Oct 1, 2003

By Mark A. Krall

The Conda Partnership's Dry Valley Phosphate mine is a thinly bedded, multiple seam, open pit mining operation where selective mining techniques are used to recover phosphatic shales. The mining methods used are truck/shovel and scraper/ dozer operations. The ore that is mined is shipped 32 km (20 miles) by rail to a beneficiation facility which upgrades the ore via washing and calcining. The mine and beneficiation complexes are owned by the Conda Partnership. The Conda Partnership is a joint venture between Beker Industries Corp. of Greenwich, Connecticut, and Western Co-Operative Fertilizers (U.S.) Inc. of Alberta, Canada. The Conda Partnership operates as a separate entity from the two partners.

Jan 1, 1984

By William O. Rasmussen

Exploration requires processing highly varying kinds and amounts of geologic information. Successful discovery dictates that this be done quickly with maximum confidence. Most phases of exploration are more or less applicable to computer reduction on a routine basis. The use of digital computers to reduce raw data into interpretable form, lets the exploration geophysicist concentrate on interpretation and presentation, and to consistently apply more sophisticated and comprehensive analytical techniques, not practical before. In applying these concepts for the past several years, various efficient programs have evolved which provide more complete evaluation of all data including the pro- vision for more unique solutions. This has resulted in greater refinement and ability to select the most advantageous drill sites in a minimum time at a minimum cost or, in rejecting as soon as possible a project on which additional effort is no longer justified. Practical examples of computer applications in magnetics (air and ground), induced polarization and resistivity are discussed.

Jan 1, 1969

By Morgan Schauerte, Laura Raimondi, Mariel Palomeque

Executives in the mining industry are facing dramatically changing market expectations on reporting and transparency regarding the environmental and social impacts of projects, supply chains and products. Companies increasingly need to disclose the governance procedures they have in place to ensure communities, investors, employees, and Indigenous partners are effectively managing social and environmental risks. These disclosure requirements begin during exploration and carry through to all stages along the project life cycle. This type of environmental, social and governance (ESG) disclosure is referred to as ESG performance by the investment community. ESG is not a new concept, and it builds on and is intertwined with many concepts such as corporate sustainability, corporate social responsibility, eco-efficiency, triple bottom line thinking, life cycle management and many others. This paper will explore how mining companies can develop a credible ESG governance approach and strategy that will reduce risk, open opportunities, and create value. This paper will summarise ESG trends and drivers, discuss the economics and investors’ perspective towards ESG, and outline leading ESG standards and guidelines of interest to investors, regulators, communities and other stakeholders. Linkage of ESG to global sustainability efforts such the United Nations Sustainable Development Goals and Global Compact will also be addressed.

Jan 1, 2023

By Finley A. Campbell

"Nickel-copper sulphide deposits associated with basic rocks in the Quill Greek area and the White River area in the Yukon Territory have been studied and compared from the view-point of their general geology, structural geology, and the mineralogy of the ores. The relative amounts of the major constituents, magnesium, iron and calcium, and the minor constituents, nickel, cobalt and chromium have been determined spectrographically for two cross sections of the basic rocks at Quill Creek and one at White River. These data, along with petrologic and field evidence, were used to determine the sill and dyke-like character and nature of the basic intrusions. Loss on ignition is employed as a measure of the degree of serpentinization. The distribution determined shows that the serpentinization does not appear to have greatly influenced the inferred original distribution and lithophile associations of magnesium and nickel. The cobalt content may have been altered.The nickel content of the serpentinized peridotites ranges from an average of 0.36 per cent in one section to an average of 0.24 per cent in each of the other two sections studied. The cobalt averages 0.0038 per cent in the samples from the two Quill Creek sections and averages 0.0042 per cent at White River. These results have been compared with other available data.The sulphide ores are later than both the peridotite and gabbroic rocks and may be co-magmatic with them. There is no evidence in these areas to support an origin by lateral secretion; on the contrary, the alteration associated with the ores, the mineralogy and spatial relationship to basic and ultrabasic rocks, indicate the ores are derived from a basic magma."

Jan 1, 1960

By C. L. Glorioso

As an introduction and credentials for our talk, let me take a moment to introduce you to Wimpey Worldwide and specifically to Wimpey Minerals, USA, Inc.

Jan 1, 1995