Search Documents

By Y Peng, B Guo

In gold processing plants, the water from the cyanidation stages is treated to detoxify cyanide species and this recycle water becomes the main part of the process water. Despite the low concentration of free and weak acid dissociable (WAD) cyanides in process water, the recoveries of gold and silver is still affected during flotation, especially when gold and silver are associated with iron sulfide minerals. This is a case at the Hidden Valley (HV) Mine. In this study, the effect of free and WAD cyanides on gold and silver recoveries by flotation from the HV Mine was considered.WAD cyanide (WAD CN) was prepared by mixing sodium cyanide and copper sulfate at a cyanide to copper ratio of 3:1 dosed at different cyanide concentrations. It was found that both free and WAD CN depressed gold and silver and particularly iron sulfides in flotation. The depressed gold and silver recoveries were closely associated with the depressed recovery of iron sulfide minerals, suggesting that free and WAD CN may not depress the flotation of liberated gold and silver minerals significantly. It was also found that 10 ppm free cyanide completely depressed the flotation of iron sulfide minerals and WAD CN depression is probably through the WAD dissociation to free cyanide species (mainly aqueous HCN) during the grinding process, resulting from a decrease in pH. Thermodynamic calculation showed that 5.5 ppm free cyanide was released in the end of grinding at an initial WAD CN concentration of 50 ppm. This research provides a guideline to counteract the negative effect of WAD CN in the flotation of gold and silver minerals.CITATION:Guo, B, Peng, Y and Espinosa-Gomez, R, 2013. The effect of weak acid dissociable cyanide on gold and silver flotation in Hidden Valley Mine, in Proceedings World Gold 2013 , pp 341-346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Earl M. Woodward

INTRODUCTION Kerckhoff-2 is a 140 MW underground hydro-electric project designed and owned by Pacific Gas and Electric Company and constructed between May, 1980 and May, 1983 by Auburn Constructors. The project is located in the western foothills of the Central Sierra Nevada Mountains, about 30 miles northeast of Fresno, California, and develops the power potential of the lower San Joaquin River and its tributaries between the existing Kerckhoff and Millerton Lakes. The Kerckhoff-2 Project consists of project roads, adits, and access tunnels, service tunnels, power tunnels, powerhouse, tailrace tunnel surge shaft, buss shaft, intake structure, discharge structure, and switchyard. In the 1920s, the Kerckhoff 1 project, consisting of a dam, reservior, tunnel, and 34 MW powerhouse, was built in the same general area as Kerckhoff-2. The tunnel was constructed by conventional methods, and was left unlined. In time, other projects were built upstream, allowing the flow of the San Joaquin River to be regulated. The Kerckhoff 2 project is designed to harness that regulated flow, providing an additional 140,000 ON of power. Kerckhoff 2 will be the primary power plant; Kerckhoff I will produce power whenever the flow rate exceeds 4,800 cubic feet. The new power tunnel is built along the east side of the San Joaquin River between Kerckhoff and Millerton Lakes, parallel to the existing tunnel but extending approximately one mile further downstream.

Jan 1, 1983

By S. C. Schaefer

The Bureau of Mines investigated tIle standard Gibbs energies of formation, 8Gfo, for MllF2 (manganese difluoride) and CoF2 (cobalt difluo-ride). High-temperature galvanic cells employing CaF2 (calcium diflu-oride) as the solid electrolyte were used to measure the open-circuit potentials for the cell reactions ?

Jan 1, 1985

By J Euston

In the 1990s round flotation tanks were introduced as a result of the lower fabrication costs for larger cells. It was soon observed that round tanks held a number of further advantages over the traditional rectangular cells, such as better hydrodynamics, lower costs and reduced footprint per unit volume.In the last twenty years flotation cell sizes have increased almost exponentially and designs of 250 to 300m3 are a well established standard with plans for full scale pilot installations of 500m3. The option to install these large cells gives flexibility in circuit arrangements and allows efficient and economic matching of flotation lines with modern mill designs. The benefits of scale up are well known with reduced numbers of cells required, lower power costs per unit volume, etc. These benefits will be briefly reviewed with specific reference to the installation of 300m3 to 350m3 flotation cells at the Copperton Concentrator of Kennecott Copper in Utah, USA.The sophisticated techniques required to model these ‘supercells’ have led to a critical review of the fundamentals of flotation science and engineering. In addition to outlining the advantages of large flotation cells, this paper will review the science which supports, and occasionally challenges, the ongoing trend to larger flotation cells.

Aug 8, 2011

By T. J. Chen

Stone coal containing vanadium is an important vanadium resource in China. Roasting and oxidation of vanadium is the foundation for extracting vanadium from stone coal. This article takes stone coal vanadium ore in Tongshan of Hubei Province as research target to conduct oxidation roasting test on it by using a self-developed low-sodium compound additive and a new optimized technology. Firstly, use potentiometric titration, X diffraction, energy spectrum and electron probe to study valence change, occurrence and phase transition of vanadium during oxidation roasting process. On this basis, primary work is done on oxidation kinetics of vanadium by exploring the steps that control reaction rate during vanadium oxidation process and determining the related dynamic parameter ? apparent activation energy. The study shows that occurrence of vanadium in stone coal of Tongshan is mainly in illite, and that the result of phase transition in roasting process is disappearance of illite containing vanadium, formation of soluble vanadate and potassium feldspar, albite. It further demonstrates that oxidation process of vanadium is step by step (V(?)? V(?)? V(?)), and its oxidation reaction is controlled by diffusion kinetics whose dynamic apparent activation energy is E1=81.19kJ.mol-1.

Jan 1, 2014

By H Vigil, G. Peach

Long tunnels with only one access shaft pose many program problems for logistics, combine these with the requirement to drive directly out under the seabed for 10.2 km, and the program issues become even more challenging. The Musaimeer outfall tunnel was one such tunnel and to meet and eventually improve on the planned completion date required a complex and extensive management of all tunnel logistics required to support consistent tunneling for a two-year period. This technical paper will discuss the management issues and solutions implemented to meet the challenges of the Outfall tunnel construction.

Dec 1, 2022

By David E. Lindorff

The impact of surface coal mining on the geologic materials and ground water in different geologic settings is being investigated by the Illinois State. Geological Survey at three abandoned surface mines in Illinois. At a site near Ottawa in La Salle County, the overburden prior to mining consisted largely of pyritic shale; sand was the major component of the overburden and spoil at a mine near Coal City, Grundy County. Clays, lacustrine silts, and some shale and limestone were the dominant premining overburden materials at a mine near Harrisburg, in Saline County. Ground-water elevations at Coal City and Harrisburg are approximately at premining levels, whereas at Ottawa they are near the base of the spoil. Ground-water quality has deteriorated at all three sites, especially at Ottawa and Harrisburg.

Jan 1, 1981

By C Rizos

Many of the ‘new paradigms in mining’ and notions of ‘sustainable mining’ have at their core the requirement for reliable, continuous centimetre-level positioning accuracy to enable increased automation of mining operations. The deployment of precision systems for navigating, controlling and monitoring machinery such as drills, dozers, draglines and shovels with real time position information increase their operational efficiency, and reduce the need for humans to be exposed to hazardous conditions. The Global Positioning System (GPS) is the best known, and only currently fully operational, Global Navigation Satellite System (GNSS) providing positioning capability anywhere in the globe, on a continuous 24/7 basis, with accuracies ranging from the dekametre-level to the sub-centimetre-level depending on hardware and operational configuration. Despite this versatility, GNSS cannot satisfy the high accuracy positioning requirements for many applications in mine surveying, and mine machine guidance and control. The reason is that increasingly open cut mines are getting deeper, resulting in a reduction of the ‘sky-view’ necessary for GNSS systems to operate satisfactorily. Yet, to date there have been no viable alternatives to GNSS that can be deployed in mine environments that can meet the challenging requirements in open cut mines.Locata Corporation, a Canberra-based company, has invented a terrestrial high accuracy positioning system known as ‘Locata’ that can augment GNSS with extra terrestrial signals to permit cm-level positioning accuracy even when there are insufficient GNSS satellite signals for reliable positioning and navigation. Locata relies on a network of synchronised ground-based transceivers that transmit positioning signals that can be tracked by suitably equipped user receivers. Hence Locata can be considered a new type of ‘local constellation’, able to provide high accuracy positioning coverage where GNSS fails. This paper introduces some of the technical aspects of this Australian technology and describes tests conducted by Leica Geosystems over the last few years at Newmont Boddington Gold in Western Australia. A recent news announcement by Leica Geosystems (12 January 2011) has confirmed that their new mine management system will have combined GNSS + Locata positioning capability – the first commercial product that integrates GNSS and Locata capabilities into a single high accuracy and high availability navigation device for open cut mine machine automation applications.

Nov 22, 2011

By Owen Matthews

THE property of Cochenour Willans Gold Mines, Limited, is in Dome township, Red Lake area, northwestern Ontario, a hundred miles north of Kenora and close to the Manitoba border. 'Planes of Canadian Pacific Air Lines, Limited, serve the district daily, except Sundays, from Kenora, Ontario, and Lac du Bonnet, Manitoba, passengers being trans-ported from Winnipeg to Lac du Bonnet by car. Freight is handled by the Patricia Transportation Company. It is brought in from Hudson, Ontario, on the Canadian National railway, in summer by water and in winter by tractor trains over the frozen lakes. The first staking on the property was done during the 'rush' of 1926 and 1927 by William M. Cochenour, and on April 30th, 1928, a syndicate was formed, taking in claims of W. M. Cochenour and Dan Willans and H. G. Young. Surface trenching was carried on almost continuously until 1934. In October, 1932, Ventures Limited took an option on the property, and in December of that year they carried out an extensive diamond drilling programme, but considering the results did not justify further work, they relinquished the option. In July, 1934, further surface work was carried out under the supervision of W. P. Mackle and, on the strength of his report, Noah Timmins Incorporated took an option on the property and agreed to make an initial expenditure of $100,000 on development work. This was carried out under the direction of Hollinger Consolidated Gold Mines and included the sinking of a shaft to a depth of 165 feet, establishment of a level at the 150-foot horizon, and some 1,900 lineal feet of drifting and cross-cutting. The results obtained from this work were not considered of sufficient promise and the option was terminated in August, 1935. Mr. Cochenour then approached Alex Mackenzie and associates, and the present Company, Cochenour Willans Gold Mines, Limited, was organized on April 9th, 1936, and sufficient money was raised to continue operations. Under the direction of W. P. Mackle, the shaft was deepened and a second level was established at the 275-foot horizon; but, due to several adverse reports by outside engineers, it was found impossible to raise sufficient money to carry on the work and operations were suspended in December, 1937. In January, 1939, an agreement was entered into with Gold Eagle Gold Mines for the milling in their plant of some Cochenour ore. A total of 4,959 tons was treated, and the results were so encouraging that further finances were raised by C. A. Gentles & Company, of Toronto. Following further development in the mine, it was decided to erect a mill. Construction was started on September 1st and the mill was turned over on November 29th. The first gold brick was poured on December 23rd.

Jan 1, 1942

By K. D. Jacob

IN the decreasing order of the tonnages involved, the uses of phosphates can be grouped conveniently into three general classes, namely, fertilizer; chemicals for military, industrial, and technical purposes; and mineral feed for livestock. The quantity of phosphate used as fertilizer, principally in the form of superphosphate, has always exceeded by far that used for all other purposes, though in recent years a marked increase has occurred in its consumption for the other two general classes of uses. Prior to the present century large quantities of superphosphate, as well as a considerable portion of the production of phosphorus chemicals, score made from bone materials which were plentiful and cheap in some areas and which could be more easily processed than phosphate rock for the manufacture of chemicals. Today, however phosphate rock has almost completely displaced bone as a raw material for the manufacture of chemically processed phosphates in nearly all countries of the world.

Jan 1, 1944

By Anand Anupam

Conventionally, beneficiation in Indian coal washeries is done using dense medium cyclones upto the size of 0.5 mm. Coal fines below 0.5 mm size are extensively cleaned by froth flotation. There are many problems associated with flotation of Indian coals, e.g. poor response of coal particles to flotation, misplacement of fine high-ash material to froth, loss of good quality coarser coals (within ?0.5 mm size range) to tailing streams, high cost of reagents, water contamination, etc. In addition, sophisticated control systems for efficient management of the fines washing circuits are needed. Thus, there is an escalation in the capital and processing costs. In view of these facts, studies were carried out to establish the cleaning potential of dense medium cyclones for beneficiation of fine coal down to a size of 0.1 mm, essentially aimed at reducing the load on fine coal circuits mainly comprising of flotation. ROM Coal (in the size range of -2 + 0.1 mm) obtained from JogtaOCM,Jharia coalfield possessing relatively low ash (about 21%) was used in this study. Purpose for using low ash coal was to further lower, its ash content down to 8% which is comparable, to the ash content of imported coal. After characterization studies, nine tests were carried out on the prepared feed sample for its beneficiation using a dense medium cyclone of non-conventional design (very low cone angle and longer barrel), by varying its apex and vortex finder diameters. The efficiency of separation has been evaluated using Tromp curves. It could be established that it is possible to produce a clean coal of 8% ash, with Ep value of 0.044, using Jogta OCM coal by treating it in a modified dense medium cyclone. These results are summarized and discussed in detail in the present paper. Keywords: dense medium, cyclone, fine coal, beneficiation, Jharia coal

Sep 1, 2012

By Henderson, Robert

A GOOD idea of the magnitude of the underground operations at Climax can be gained from the following figures. A little more than 43,000,000 tons has been drawn from the mine and of this amount, 40,500,000 tons has been drawn in the past ten years and 12,000,000 tons was drawn in two of the war years. The maximum daily average output over a period of one month was slightly more than 20,000 tons but during this period, production on certain days was 24,000 tons, and 9000 tons was produced in a single eight-hour shift. This production came chiefly from 260 draw points although all of them were never in operation at one time. The haulage system for these draw points is made up of 7.5 miles of 36-in.-gauge track, and 131,000 ft. of subsidiary drifts and 44,000 ft. of raises have been driven to develop the necessary broken ore reserves for this high production. Power consumption is often considered an index of operating efficiency. In 1943, the year of maximum production, the mine power consumption was 19,223,000 kw.-hr. or 3 kw.-hr. per ton; in 1945 it was 3.5 kw.-hr. per ton. To handle this amount of power, there are four transformer stations and one switch station in the mine. Mr. Garrabrant, the chief electrician, describes the electrical installation in this issue.

Jan 1, 1946

By E K. Chiw, S-M Jung, S M. Masuka, ika

The world reserves of high-grade iron ore have depleted necessitating the need to utilise any existing natural iron ore deposits to meet the demands of the world’s expanding economy using hydrogen in the reduction process to curb CO2 emission. These low-grade ores include iron ores with high phosphorus content. The thermodynamic conditions in the blast furnace allow for the reduction of phosphorus that readily dissolves into the molten iron. Phosphorus in the gaseous state readily dissolves into the molten iron and therefore must be removed due to its negative influence on the mechanical properties of steel. The removal of phosphorus from molten iron is difficult causing the phosphorus to concentrate in metallic iron. The aim of this study is to provide basic knowledge on the phosphorus distribution after reduction using the CO-H2 and possibly provide the optimum conditions for phosphorus partitioning into slag, increasing the probability of its removal by magnetic separation. Total porosity, pore size distribution and surface area of the pellets used were measured using a mercury pressure porosimeter. The reduction was carried out using thermogravimetric analyses (TGA). The reduction rate increased with increasing H2 and was highest when 100 per cent H2 was used. Metal elements distribution in the reduced pellet was clarified using electron probe microanalysis (EPMA) and showed that phosphorus was distributed in the same areas as Ca. More phosphorus was concentrated in slag when 50 per cent CO–50 per cent H2 was used, increasing the probability of dephosphorization using magnetic separation. The concentration of phosphorus into slag was related to the rate of reduction. Further investigations into the reduction kinetics of this ore by CO-H2 is suggested to validate these findings. Nevertheless, a comprehensive thermodynamic analysis of the reduction of phosphorus containing phases found in iron ore with carbon, CO and H2 was provided to assist in selecting the optimal reduction experimental conditions.

Sep 18, 2023

By L. E. Young

GERMANY'S recent collapse and the occupation by the Allies of the coal fields of the Ruhr, the Saar, Silesia, Poland, and Czechoslovakia have focused attention on the postwar coal problems of Europe. American coal operators are interested deeply in what is happening in Britain, particularly in the discussion of plans to rehabilitate and reorganize the entire British coal mining industry, as such reorganization will probably determine the place Britain will occupy in the European coal markets for the next few decades. The continuing decline of British out-ut per man-shift, particularly during wartime, has resulted in a most serious effort to determine whether this unfortunate trend is due to the physical condition of the coal seams, poor management, poor engineering and planning, inadequate use of power and machinery, or failure of labor to co-operate with management.

Jan 1, 1945

By O Joneydi, J Viljoen, R Funnell

Computational Fluid Dynamics (CFD) modelling is a useful tool that can assist engineers in designing effective ventilation systems for the control of airborne dust generated during mining operations. Thistechnology can save time, effort and the costs associated with re-work or the traditional on-site experimental field trials by running desktop 3D simulations of the various proposed scenarios using state-of-the-art CFD analysis tools. Before implementing a dust management system, an understanding of the behaviour of airborne dust particles in the face zone can be achieved, which can improve the confidence in the secondary ventilation and dust management design. Usingadvanced numerical models, suitable dust extraction strategies can be foreseen, and multiple scenarios can be simulated and investigated quickly. As a case study, dry drilling operations in Kimberlite orebodies produce large quantities of fine dust which poses health and safety risks. An effective dust management system is required to achieve acceptable face conditions. A possible practical solution is a ducted exhaust ventilation system with a force fan in the face zone. This paper demonstrates how CFD analysis can be used as a tool to assist the design engineer with validating and optimising the proposed ventilation design by tracking the trajectories of different size dust particles, to determine the best equipment layout and appropriate flow rates which minimises airborne dust.

Oct 12, 2022

By Emery R. Hayhurst

SILICOSIS has been described in a report of the American Public Health Association as a disease due to breathing air containing silica, characterized anatomically by generalized fibrotic changes and the development of miliary nodulations in both lungs, and clinically by shortness of breath, decreased chest expansion, lessened capacity for work, absence of fever, increased susceptibility to tuberculosis (some or all of which symptoms may be present), and by characteristic X-ray findings. ... The disease is divided arbitrarily into first, second, and third stages for convenience of description and possible compensation purposes. At least two distinct types of silicosis are recognized, acute and chronic. The acute form was reported as early as 1713, when a British patent for grinding flint by wet methods was granted because the dry powdered material "proved very destructive to mankind, so much that any person, ever so healthful, working in that business cannot possibly survive over two years."

Jan 1, 1936

By R. L. Keiski, H. Miettunen

"The serpentinite massifs of Hitura are located in the municipality of Nivala in Central Finland. The most important sulfide minerals in the ore are pentlandite, pyrrhotite and chalcopyrite. The ore body consists of amphibolite rocks in contact with serpentinite against mica gneiss. The mean Ni grade of the ore is about 0.7%, and the highest Ni grades have been encountered in close contact. In general, the inner parts of the ore are strongly serpentinized ultramafite and some sulfides have been converted to mackinawite and valleriite. The degree of alteration varies considerably within the ore body and, correspondingly, the grain size of the sulfides varies as well. In this study, flotation tests were done with samples from different zones of the ore body. The flotation test results on the bench scale and plant scale are discussed in terms of the mineralogical features of the ore. Ores in the North Hitura zone differ from those in the South Hitura zone.IntroductionThe Hitura nickel mine, like the entire Nivala area, is part of the Bothnian Svecokarelian schist zone, where numerous Ni-Cu boulders have been discovered since the early 1930s. The Nivala area has therefore been the subject of exploration activities by the Geological Survey of Finland (GSF) and mining companies. The first period of exploration started in 1936, and the Makola nickel deposit, located 3 km south of the Hitura mine, was discovered by GSF in 1937. About 415,000 tonnes of ore were mined at Makola between 1941 and 1954. In 1937, during the exploration and development stage of the Makola mine, boulder tracing and a geophysical survey revealed a significant ultramafic body with some lowgrade Ni-Cu occurrences in the South Hitura zone.In 1961, GSF continued the exploration program in the area and discovered the North Hitura ultramafic complex and its allied Ni-Cu occurrences. In 1964, Outokumpu Oy bought the property and, after underground exploration, comprehensive mineralogical studies, process research and a feasibility study, production started in 1970 (Isohanni et al., 1985)."

Jan 1, 2015

By Gordon Kidd

Inflation and burgeoning costs are two among many factors which have generated a new surge of interest in "fringe benefits" (sometimes referred to as "supplementary remuneration" or "supplementary compensation"). Other specialized forms of compensation ("perks", in the vernacular) such as company cars, windowed offices, etc., which also are the subjects of current study, are outside the scope of this paper. For businesses, interest in fringe benefits is based on concern for employees? welfare, compliance with government requirements, and an increasingly burdensome impact on bottom lines. In 1980, according to Fred D. Lindsey in the October 1980 issue of Nation's Business, employee benefits will cost American employers an estimated $420 billion. To paraphrase Winston Churchill, "some fringes!" Indeed, few if any administrators consider employee benefits as fringes. Employee benefits impact other major areas of a company's operations as well. As listed by Beadle (1980), these areas include employee relations, collective bargaining, short-term costs, long-range funding, manpower planning, compliance with legislation, taxation for the company and for the employee, corporate image in the community, competitiveness for staff, communications, administration, claims cost containment, etc., etc.

Jan 1, 1980

By G. Minhas, M. Pule, Y. Laffitte, M. c. McGurn, T. Tzanetakis, Peacey. J., R. Susilo

Titanium (Ti) metal production from titanium tetrachloride (TiCl4) using magnesium (Mg) as a reducing agent is the well-known Kroll process. A chloride route is used to avoid oxidation of the titanium sponge. The sponge is consolidated into ingots and can then be made into powder by melting and atomizing or by hydriding/dehydriding. Attempts at direct powder production have met with difficulties, including low Ti yield and the formation of very fine particles (particles between 25-100 µm are desired). This paper discusses two methods to produce Ti powder in a molten salt medium using magnesium powder as a starting material instead of a pool of molten magnesium. The first method is a direct reduction of gaseous TiCl4 injected in the melt with the magnesium powder in suspension in the molten salt. The second method is a two stage TiCl4 reduction reaction where recycled Ti was used to form titanium dichloride (TiCl2) in the first stage followed by addition of magnesium powder into molten salt in the second stage. A correlation between Ti yield and processing variables such as TiCl4 to Mg ratio, Mg particle size, TiCl2 concentration in the melt, and reaction temperature was studied. The Ti powder formed was also analyzed for particle size distribution. Despite challenges and difficulties encountered, this paper shows some promising results which could provide guidance to others working on direct Ti powder production.

Jan 1, 2015

By John Durkin

A computer model has been generated to evaluate speech intelligibility of individuals wearing conventional and electronic hearing protectors. For speakers talking at normal levels in noise levels of 65 db(Lp) or less, it was found that conventional hearing protectors significantly reduced speech intelligibility. Under the same conditions, electronic protectors provided scores equal to those for the unprotected individuals while providing protection from high noise levels. Therefore, electronic hearing protection is valuable in areas where high noise level is intermittent.

Jan 1, 1979