Search Documents

By Timothy Batchler, Khaled Mohamed

Standing supports have been used in coal mines for decades to enhance roof support capability. Sometimes standing supports are used as a tool to resist the lateral movement of spalled ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) are conducting a testing program for different types of standing supports (steel and timber) to investigate the effect of lateral loading on their vertical loading capacities and the factors affecting their lateral loading capacities. In this paper, the mine roof simulator (MRS), at the NIOSH Pittsburgh research facility, was used to determine the response of steel props to vertical and horizontal loadings. Finite element models (FEMs) were developed and verified using the tested steel props. To justify the testing program for testing standing supports with end-conditions of rock-like materials, the verified prop models were used to study the effect of a wide range of roof and floor materials (gray shale, shale, and claystone) on the critical buckling loads of the steel props. Also, several lateral loading scenarios were evaluated in which the steel props were laterally loaded at different heights. The critical buckling load for steel props setting up against a claystone roof and floor was found to be one-half of that shown by the MRS test where roof and floor platens are made of steel. Minimum prop performance was observed when the lateral load was applied at the mid-height of the steel prop, especially at small lateral displacement (less than 2 in).

Sep 10, 2022

1.0 Control House (DWG. NO. 56-401-G) - 1.1 Physical Description The Control House is a single story, 2728 square foot building with an adjacent transformer yard. A four foot overhang provides shade protection for the walls. The building is heated and air conditioned. The HVAC System has an elevated outside air intake and provides a positive pressure environment within the structure in order to prevent the infiltration of heavier-than-air, noxious gases. The materials of construction are as follows: Structure : Light-Gage Metal Framing Exterior Walls :Outside - Preformed, Metal Siding :Inside - Insulated Metal Liner Panels Interior Partitions :Gypsum Board over Light-Gage Metal Framing Roof :Insulated, Preformed Metal Panels Ceilings :Mechanical & Electrical Rooms - Exposed underside of Roof Panels Control Room, Lunch Room, Toilets, Entry - Suspended Acoustical Lay-In Tile Floors :Mechanical & Electrical Rooms - Concrete Slab on Grade Control Room, Lunch Room, Toilets, Entry - Resilient Tile Exterior Doorsand Windows :Preformed Metal Panel Manufacturer's Standard Units

Jan 1, 1979

By Gang Chen

This paper explores the possibility of using short-term time-dependent plate loading tests to estimate the elastic and viscoelastic parameters of the weak floor strata typically associated with coal seams in Illinois. Plate loading tests with incremental loads, similar to incremental creep experiments, were conducted until the floor failure occurred. For each increment, the load was held constant for a period ranging from 1-4 hours until a constant deformation rate was achieved. The deformation-time data were analyzed for viscoelastic parameters of weak floor strata assuming its behavior to be adequately represented by the standard Burgers model. The analysis required development of mathematical equations for the time-dependent deformation of the standard Burgers material under a three- dimensional state of stress. Time-dependent pillar settlement data at one mine were also analyzed for elastic and viscoelastic parameters of the weak floor strata using the developed equations. These parameters were compared with similar parameters estimated from plate loading tests.

Jan 1, 1990

By Terry R. Neumann

In 1989, the Bureau of Mines conducted a mineral resource investigation of the 52,350-acre Jersey Jack study area, located in the Clearwater Mountains of north-central Idaho. Twenty-eight mines and prospects were examined, and 483 rock, placer, and petrographic samples were collected during the field study. Two properties contain gold resources; mining company data show the Robinson Dike mine contains an estimated 940,000 tons of "drill proven and probable reserves" averaging 0.041 oz/ton gold, and the Bureau of Mines investigation showed the Blacksand placer mine contains an estimated 64,000 cubic yards of identified placer resources averaging $8.13 in gold per cubic yard. Sample analyses from other properties indicate that gold resources are likely to exist; however the low tonnage, narrow, fissure-vein type deposits would require mining by relatively high-cost underground methods and would be subeconomic at a gold price of $400/oz.

Jan 1, 1991

By Charles P. Lazzara, Alex C. Smith, Richard W. Pro, Mark W. Ryan

The U.S. Bureau of Mines conducted a study to determine if commercially available automatic sprinklers could withstand the high static pressures in deep underground coal mines without leaking and if exposure to the mine environment affected their leak pressures. New sprinklers and sprinklers exposed to the mine environment were subjected to increasing pressures until leakage occurred. The average leak pressures of the new sprinklers ranged from 640 to 2,300 psig and were significantly different for sprinklers from different manufacturers and for different types of sprinklers. Different for sprinklers from different manufacturers and for different types of sprinklers. Generally, standard-response sprinklers withstood higher pressures than fast-response sprinklers. The results indicated that most commercially available sprinklers would withstand the high static pressures in deep underground coal mines; however, they would not provide the same reliability and safety factor as sprinklers used aboveground at or below their rated pressure of 175 psig. The average leak pressures of the sprinklers exposed to the mine environment ranged from 740 to 1,180 psig. The mine environment affected the ability of 66% of the sprinklers to withstand high static pressure New sprinklers were also evaluated at pressures of at least 500 psig for 30 days to determine their ability to withstand long-term exposure to high static pressures; no leakage was observed.

Jan 1, 1993

By M. A. Schellhardt, E. J. Dewees, R. Vincent Smith

"INTRODUCTION Abnormal material requirements of the nation at war impose an intensive demand upon many irreplaceable natural resources. Natural-3as reserves) for example, are being subjected at the present time to extensive depletion by large-scale withdrawals of gas to supply unprecedented demands for fuel and raw materials for the synthesis of strategic products. Fluids produced from many so-called gas-condensate type reservoirs have become an important source of hydrocarbons vital to the war effort.Development of gas-condensate type reservoirs in Arkansas, Louisiana, and Texas in recent years created many problems not common to ordinary gas-producing operations. Early in the development of condensate-type gas fields, general practices were evolved and applied to insure efficient re¬covery of the hydrocarbons existing in the gas phase under initial reservoir pressures and temperatures, put often the practices were predicted mainlyregardingupon generalized theory regarding the behavior of the fluids and were not always the most efficient, because field and laboratory procedure for testing these hydrocarbons had not progressed as rapidly or as far as field development. Specific information regarding the composition and properties of fluids ultimately recoverable from many gas-condensate reservoirs, especially, is lacking."

Oct 1, 1944

Microorganisms are finding more use in the mineral industry, with extensive research efforts being reported in 1991. Most of these research efforts were presented in two major meetings, the SME Annual Meeting in Denver (February, 1991) and the Engineering Foundation Conference about Mineral Bioprocessing in Santa Barbara (June 1991). In addition, several articles were published in the IMM Transactions, Minerals and Metallurgical Processing and Water, Air. and Solid Pollution Journal. The literature can be categorized as: • Review articles presenting an overview of the activities in the use of biotechnology in mineral processing. • Research efforts into genetic manipulation of microorganisms to perform a specified job. • Studies in bioleaching of metals from different types of ores. • Biotreatment of wastes from the mineral industry including acidic mine waters, uranium tailings, cyanide destruction, etc. • Investigations into the role of microorganisms in the energy materials, such as oil, coal, tar sands, oil shales, etc. Smith (Mineral Bioprocessing Conference) presented a review of research efforts as well as practical applications of biotechnology in the mineral industry. In another article, Smith et al. (Minerals Engineering) emphasized that extensive fundamentals and applied research work should be pursued to explore the fundamentals, potential and practicality of the various possible uses of microorganisms in mineral engineering.

Jan 1, 1992

By W. F. Wyman, S. F. Ravitz

"INTRODUCTION By far the greater part of the high-grade manganese ore used in the United States is imported from overseas. During the early part of the recent World War importations of manganese ore were seriously threated, and it appeared that it would be necessary to utilize low-grade domestic ores to the fullest possible extent. Among the processes that appeared to offer the best possibilities for beneficating low-grade domestic oxide manganese ores, which ordinarily are net readily amenable concentration by ore-dressing methods, were those involving leaching with sulfur dioxide. The Bureau of Mines therefore investigated the amenability of a large number of such ores to sulfur dioxide leaching.Several sulfur dioxide processes for beneficiating low-grade oxide manganese ores have been proposed. 3/ One of these, based on a patent by Van Arsdale and Maier, 4/ was used recently in a plant constructed to treat 1,000 tons per day of 20-percent manganese ore from the Three Kids deposit near Las Vegas, Nev. 5/ In this process the ore slurry is leached with sulfur dioxide gas, the resulting solution is evaporated to crystallize the manganese sulfate, the crystals are decomposed thermally to produce high-grade manganese oxide and regenerate sulfur dioxide, and the manganese oxide product is nodulized. The Bureau of Mines has recently developed a process 6/ in which a suspension of the ore in calcium dithionate solution is leached with dilute S02 gas, the manganese is recovered from the resulting solution by a simple lime precipitation, and the precipitate is nodulized or sintered to form a high-grade manga¬nese oxide product."

Jun 1, 1947

By Karl C. Dean

All components of 15 automobiles manufactured between 1954 and 1965 were analyzed, and it was determined that a representative junk automobile would have the following composition (all figures in pounds): steel, 2,532; cast iron, 511; copper, 32; zinc, 54; aluminum, 51; lead, 20; rubber, 145; glass, 87; miscellaneous, 142. Time and motion studies and a cost evaluation were made to determine if such a typical vehicle could be economically burned in a smokeless incinerator and hand-dismantled, and if the resultant steel could be baled into a high-quality No. 2 bundle containing less than 0.10 percent copper. The cost evaluation showed that processing the composite car would cost about $51 to produce about $56 worth of marketable ferrous and nonferrous metal products and provide an annual rate of return on investment of 19 percent.

Jan 1, 1969

By J. P. McGee

The Bureau of Mines is doing research and development work on a coal-fired gas turbine plant initially developed by the Locomotive Development Committee, (LDC) of Bituminous Coal Research, Inc. The Bureau is redesigning the turbine blading and some of the auxiliary equipment, and is reerecting, the plant at the Morgantown (W. Va.) Coal Research Center. The present goal is a 1,500-hour run at virtually the same operating conditions used by the LDC in their final 1,100-hour test with the turbine. This will allow the Bureau to properly evaluate the new blade design. Erosion of the turbine blades (particularly the roots) by ash in the hot gases from the combustion of coal was the most serious problem in extended operation in earlier experimental work. New blades made of Stellite6 are being fabricated for the stator and rotor, and armored wear strips of titanium carbide will be inserted in the blades at the areas of probable maximum ash velocity and concentration. The trailing edges of the rotor and stator blades are being thickened and thinned, respectively, to induce the ash to travel to the casing and prevent it from returning to the base of the rotor blades. The first stage rotor and second stage stator blades are being removed to provide an annular space for maximum quantities of coal ash to centrifuge to the casing. Additional blades will be added to most of the rows in the stator to stop secondary flow of dust-laden gas toward the rotor. A contract has been awarded for fabrication of the new blades. The 1,500-hour run will be started as soon as the new blades are installed.

Jan 1, 1962

By Bruce Rock

A continuous mining machine was redesigned for the installation of an integrated illumination system. The illumination system was designed by first calculating the theoretical number of luminaires required to meet the Federal Illumination Standards. Luminaires initially were placed using isointensity diagrams. A darkroom was used for "fine tuning" and demonstrating that the system met the illumination requirements. The luminaire mounts were installed on a machine underground. The performance of this illumination system was monitored in the working environment of an operating coal mine. Design changes were made as necessary during this evaluation period to improve the system.

Jan 1, 1979

By Thomas G. Chapman

The four major steps in the production of marketable copper are mining, concentrating, smelting, and refining. In a few cases, however, leaching takes the place of concentrating, smelting, and refining, and in others ores are smelted without being concentrated. Copper ores have been milled since the early days of mining in the United States. Except in the Michigan district, most copper ores went direct to the smelter until the so-called porphyry mines were developed. At present, although considerable leaching and direct-smelting ores are produced, the bulk of the copper ore mined is concentrated. Improved methods of concentration have kept pace with the increased tonnages of ores milled.

Jan 1, 1936

By Byron M. Bird, Earl R. McMillan

"The method and apparatus described herein was developed at the Northwest experiment station of the Bureau of Mines, Interior Department, in cooperative research work with the University of Washington. A fuller description will appear in a bulletin entitled ""study of coal washing problems in the Pacific Northwest, to be published by the University. During the past four years this Bureau and the University have been co-operating with various coal companies in the Pacific Northwest in an extensive study of coal washing problems. Much of the valuable data resulting from this study has been obtained with the well-known float-and-sink test. This test has known for a number of years****, but its possibilities have not been thoroughly understood. A few investigations have developed apparatus and technique suitable to their needs, but these were not adopted to the conditions faced in the Northwest. Thus, the necessity arose for designing suitably equipment and working out a method of procedure or technique in carrying on the fundamental studies of coal washing by means of the float-and-sink test method."

Feb 1, 1924

By Manuel Rapiman, Ricardo Sepulveda

The feasibility study of Escondida Norte (ENorte), recommended a slope angle design for the Final Pit. But, according to the experience obtained with the slope adjacent to the West wall of ENorte, in which Compañia Minera Zaldívar (CMZ) gained in its phase 4, a slope of similar geotechnical characteristics will be exposed in the West Wall of Phase 1 (Premine) and of the Final Pit, with an interramp angle 53º and with very good stability results. In this regard, Minera Escondida Ltd. (MEL) performed a study of the slope angles for the phases mentioned and according to this delivered the results of this evaluation, the recommendations and/or the necessary conclusions in the design to ensure that the slopes are stable enough and may enable safe operational management of them.

Jan 1, 2006

By R. V. Ramani

This volume is the first of a four-volume final report on research carried out under a contract from the U.S. Bureau of Mines on the development of a computer simulation model for surface mine reclamation planning. The other volumes are titled as follows: Volume II: Dragline Model, Volume III: Mine Coordinate Generator System, and Volume IV: User's Manual for OPMHS/2. This report deals with the development of a geological model for surface mine planning. The most common orebody modeling techniques are described. A brief review of geostatistical theory and concepts is presented. A geostatistical option for orebody modeling is developed and validated. Computer programs and sample outputs are appended.

Jan 1, 1985

By Marshal Scherba

Coal seams approximately 7 feet, 9 feet and 20 feet thick at depths of 250, 600 and 1,000 feet respectively were detected using high resolution seismic reflection techniques. Investigation of seismic profiles indicates that good data are required to delineate faulting with only 20 feet of throw but that faulting with 50 feet of vertical displacement can be detected with poor data. Data acquired from dynamite charges fired in water saturated media were clearly superior to that acquired using charges dry tamped in 10 and 20 foot holes.

Jan 1, 1977

By Marwan M. Mohammed, Hani S. Mitri, Wilfrid Comeaul, Baoyao Tang

In many parts of the world, rockbursts have become a major problem of mining at depth. As orebodies are being mined deeper, rockburst phenomena have become familiar to deep hard rock mines. Rockbursts are generally characterised by sudden release of energy in a volume of highly stressed rock, which can cause local violent failure of the rock mass around the opening. One method of controlling these failures is to precondition the rock mass by detonating fully confined explosive charges at the appropriate locations. This method known as destress blasting, was first tried in the deep South African gold mines (Roux et al., 1957), and was widely used later in Canada, United States, France, Poland and Japan.

Jan 1, 1999

By R. Stefanko

This study concerns itself with the effects of diesel exhaust on mine ventilation systems. The approach here consisted of the development of mathematical models for emissions, dilution, and dispersion of gaseous pollutants from diesels. The general scheme was to use partial differential equations to predict concentration growths. Specifically, the following situations were modeled: 1. A single stationary diesel engine working in a single roadway. 2. A single diesel engine moving with uniform velocity in a single roadway. 3. Multiple diesel engines moving continuously in a cycle in a roadway with appreciable leakage. 4 Multiple diesel engines moving continuously in a cycle in a roadway with little or no leakage. 5. Multiple diesel engines moving randomly in a roadway with uniform air velocity.

Jan 1, 1974

By R. L. Balmer

This information circular, which describes the methods and costs of sinking a small underground shaft with steel supports at the Keystone mine of American Smelting and Refining Co., near Crested Butte, Colo., is one of a series being prepared by the Bureau of Mines on current shaft-sinking practices in various mining districts of the United States. Preparations for sinking a combined exploration, development, and production shaft from the lowest level of the Keystone mine began early in 1957. This vertical, three-compartment, 6-1/4-by 16-foot rectangular shaft was to be sunk in separate stages or lifts so as to correspond with the progress of an associated lateral exploration and development program. The first section of the shaft was collared and sunk to a depth of 209 feet between September 1957 and April 1958. Because of the depressed base-metal market, the mine was shut down as soon as the initial phase of the exploration and development program had been completed and before any deeper sinking could be attempted.

Jan 1, 1962

By J. C. Gerdeen

It is of upmost importance to keep the size of the program to a minimum for the computer being used. One way is to reduce the size of the data bank by adjusting the large common array A in the main program (page, line 32) and the statement following the assignment of A. The current value of A is 35001 and is optimized for the UNIVAC computer with 5,000 words of useable storage. Another way to reduce the required storage is to overlay the program. That is, to have in the computer only the subroutines which are being used. In large finite element codes, overlays or segmentation of the program is a necessity. The code presented here has three levels of segments and are presented graphically in the tree in Figure D-1.

Jan 1, 1976