Search Documents

By Charles C. Boley

High-volatile A bituminous coal from the Allen mine, Las Animas County, Colo., blended with char produced from the same coal yielded accept-able metallurgical coke in a 500-lb movable-wall test oven. Nineteen experimental runs were carried out using several concentration levels of two different chars, 5.6 and 19.6 percent volatile matter, produced by entrainment carbonization of the base coal. With the higher-volatile char, an acceptable coke was produced at a 22.5-percent concentration; the lower-volatile char did not produce an acceptable coke at the concentrations investigated.

Jan 1, 1972

By A. J. Forney

The hot-gas-recycle process, for the hydrogenation of carbon monoxide, was investigated in a 12-inch-diameter reactor. Initially because the distribution of gas was poor, hotspots developed in the catalyst bed. After the velocity profile of the gas flowing through the bed was studied, the method of packing the catalyst was altered. Because this change improved the distribution of gas, temperature control was excellent. The l2-inch-diameter reactor was operated successfully in the synthesis of gaseous and liquid fuels. When high-Btu gas was synthesized in two stages, parallel-plate assemblies of Raney nickel were almost as active as granular Raney nickel in the second reactor. The pressure drop through the second reactor, however, was reduced 90 percent by the use of these assemblies.

Jan 1, 1962

By H. Naghavi, M. Karimi

"In self-aerated flotation machines, the gas rate depends on operational variables (e.g. froth depth and impeller speed), pulp properties (e.g. solid content and viscosity), and reagent addition (e.g. type and concentration of frother). The gas rate has a strong correlation with the flotation performance by influencing the gas dispersion properties and froth retention time. A factorial experimental design was used to study how the gas dispersion properties, the froth retention time, and the flotation performance respond to changes in froth depth and impeller speed (as the most common operational variables). An in-depth understanding of the effects of impeller speed and froth depth on the gas dispersion properties, especially the bubble surface area flux and froth retention time, is necessary to improve operating strategies for self-aerated flotation machines. All experiments were carried out in a 50 m3 selfaerated flotation cell in an iron ore processing plant. The results showed that the froth depth affected the metallurgical performance mostly via changing the froth retention time. The impeller speed had two important impacts on the metallurgical performance via varying both the froth retention time and the bubble surface area flux in the froth and pulp zones, respectively. The interaction effects of the froth depth and impeller speed were also established. This allowed us to develop a strategy for operating selfaerated flotation machines based on varying the froth depth and impeller speed with regard to the cell duty. IntroductionA mechanical flotation machine may be divided into two distinct zones. namely the pulp zone and the froth zone (Goodall and O’Connor, 1989; Yianatos, Bergh, and Cortes, 1998; Rahman, Ata, and Jameson, 2015a, 2015b). The overall flotation recovery, Ro, including the true flotation (particles attached to the bubble lamellae) and entrainment (particles recovered in water held in the bubble plateau boundaries), is a function of the recoveries in the two zones. It is calculated as follows (Dobby, 1984):"

Jul 1, 2019

By Richard E. Thill

Elastic wave velocities and moduli were determined by both the pulse and resonance methods in a large number of specimens of St. Cloud Gray Granodiorite and Tennessee marble under the same moisture, temperature, and stress environment. Long cylinders were first tested by the resonance method to obtain longitudinal bar and torsional wave velocity. The cylinders were then sectioned in half and tested by the pulse method to obtain the transient pulse velocity. These velocities were later used to obtain various moduli for comparison. Statistical comparisons between the Young's, shear, and bulk moduli and Poisson's ratios obtained independently by the pulse and resonance methods indicate that the methods do not give equivalent results in nearly isotropic rock. The amount of difference varies for each modulus, with the least difference (less than 5 pct) occurring in the shear modulus and the greatest difference (as high as 34 pct) in the bulk modulus. Moduli determinations in aluminum show much closer agreement between the pulse and resonance methods than in rock. The discrepancy in pulse and resonance results probably is caused by frequency dispersion effects and by differences in error sensitivity in the various formulas used to calculate the moduli.

Jan 1, 1974

By E. C. Morton

The Western Australian School of Mines (WASM) has developed a facility for the static testing of large scale ground support elements. The samples are loaded using a mechanical screw feed jack. Instruments measure the displacement and the load being applied. Methods have been developed for testing of mesh, shotcrete and membranes. Mesh samples are restrained on all sides and loaded centrally. A new large scale punch test method has been developed to evaluate shotcrete and membranes. These products are sprayed on to a sandstone substrate containing a centrally located isolated disc. The sprayed product is loaded by displacing the disk. The different test methods are described in detail. The test program involved two types of mesh, several shotcrete mix designs with different curing times and one membrane product. The force-displacement responses are used to directly compare the products. The implications for implementation of the different ground support products are discussed.

May 1, 2009

By A. J. Basu

New technologies, such as computer based learning, wireless computing, internet2, online courses, distance learning, and in general multimedia applications are being implemented in the higher education sector in an increasing manner. However, these implementations are not coherent, and lack standards. However, one example of the existing standards is the development and implementation of the virtual learning environments. These technology tools help in delivering the eLearning objectives. There is a major initiative in Europe (eEurope action plan) in promoting eLearning towards creating a knowledge-based society. Technology implementation is the major driver for achieving the eLearning objectives. A two-year pilot project on implementing technology tools including virtual learning environment (VLE), video-conferencing, and simulation and visualization was carried out for providing a blended learning environment for undergraduate and graduate students in Mining Engineering (undergraduate) and Mineral Deposit Evaluation (M.Sc.) course at the Imperial College London. The pilot project was funded by the Imperial College Centre for Educational Development (ICCED). The project did contribute towards activities for creating an institute-wide eLearning strategy in line with the eEurope action plan.

Jan 1, 2003

By Charles De Witt

The ore treated at the reduction plant (called Yangdei) of the Chiksan -Mining Co., Korea, is brought from four of the company mines, and from the small tribute mines. The largest shipments conic from Sajunkohl mule, situated about a mile and a half from the mill (Fig. 1). The ore is quartz of medium hardness. The overage assay value in gold is $6.95 per ton. At the mine the ore is put into bin,, and is Mien trammed over an 8 per cent. grade to the tipple bins above the mill, where the ore is drawn through the hull holes as desired. The capacity of the tipple bins is about 3,500 tons. On, from Moonsukohl, Chung Tarrie, Yang Chun, and the tribute mines is brought in by bulls and bull wagons. The bulls carry from 350 to 800 lb.; the average wagon load is about 1,200 lb. (Fig. 2). One shovelful of ore out of every ten is taken as a sample. Considerable ore

Jan 5, 1915

By Sam S. Taylor

Subsurface disposal of oil-field brines was practiced in Oklahoma on a limited scale as early as 1925. The technique of subsurface injection has been improved immensely and has been applied with varying success in many oil-producing areas in Oklahoma, and elsewhere. This method of disposal, however, is only one of several methods available to operators of oil-producing properties, but, in contrast with usual methods of handling brines on the surface it eliminates the damaging effect of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. Other methods of brine disposal approved by regulatory agencies in some States include (1) impounding in impervious ponds and solar evaporation, (2) controlled diversion into surface waters, and (3) recovery of the mineral salts of the brine. In most, States where oil is produced regulatory bodies authorize the use of one or more of these methods of brine disposal. In Oklahoma, for example, the Oklahoma Planning and Resources Board of the Conservation Commission has been authorized to adopt whatever methods or means may be necessary to prevent contamination by mineralization of all potable waters within the State.

Jan 1, 1942

By John P. Hager

A special inlet system has been developed for a TOF mass spectrometer that allows the equilibrated high-temperature vapors from an atmospheric-pressure flow reactor to be leaked into the ion source of the mass spectrometer without undergoing any compositional changes. Using this flow reactor - mass spectrometer system and a modified transpiration system (one that allows for the carrier stream to be equilibrated with two different condensed samples) a series of fundamental vapor transport studies were undertaken. The results of these studies are summarized as follows: 1. The vapor species in equilibrium with condensed copper (I) chloride were determined to be Cu3C13, Cu4C14, and Cu5C15. The gas mixture is fifty percent tetramer near the melting point (703°K), with the percentage of tetramer decreasing with increasing temperature. The following thermodynamic results were obtained.

Jan 1, 1977

By Maya Kamenetsky, Khoi Nguyen, Natalee Bonnici, Steve Walters, Claire McMahon, Julie Hunt, Ron Berry

"The analysis of meso- and micro-scale textural attributes has been undertaken on ore samples from the Ernest Henry iron oxide-copper-gold (IOCG) deposit in NW QLD. Quantified textural data including grain size, shape and mineral association have been extracted from classified images of core with the aim to better predict potential mineral processing behaviours such as comminution, liberation and flotation. Data have been extracted from images of intact core at meso- and micro-scales using high resolution continuous images collected using automated core-logger technology, SEM-based and optical microscopy platforms.The results of this study will show examples of quantified size, shape and mineral association data from meso- and micro-scale classified images. Analysis of the data shows that there are domains of variable grain size and mineral association that can potentially be related to crushing and liberation behaviour. The trends that are observed at the drill-core (meso-) scale are consistent with those at the micro-scale. The results from the micro-scale analysis show that the domains defined at the core-scale have clearly different chalcopyrite sizes and shapes as well as variable bulk mineralogy.INTRODUCTIONInnovations in technology have allowed automated extraction of information about mineral shape, grain size and mineral association, i.e., texture, from meso- and micro-scale images of intact rocks. The overall aim of this research is to investigate trends in quantified textural data that can potentially give an early view of processing parameters such as predicted grind size and liberation behaviour."

Jan 1, 2009

By Jinwu Kang

The hydraulic turbine blade of the matensitic stainless steel (Cr13%,Ni5%,Mo1%) is a kind of large and curved shape, which is susceptible to deformation in both casting and heat treatment processes. The coupling analysis of heat transfer, phase transformation and stress in heat treatment process of the turbine blade for Three Gorges Project is carried out by using Deform-3D software. Its temperature fields, phase fields and stress fields in heat treatment process are obtained. And its deformation is predicted. In the cooling process of normalizing, the blade exhibits relatively large deformation. Based on the stress analysis and deformation prediction in heat treatment process, an algorithm for the determination of reverse deformation of the blade casting in heat treatment process is presented. And the reverse deformation distribution of blade is obtained.

Jan 1, 2010

By Paul C. Hyndman

No minerals have been produced from the McGraw Creek RARE II area. During the 1982 U.S. Bureau of Mines study, there were no active mines in the area. Limestone occurrences (fig. 1, no. 2), four copper prospects (fig. 1, no. 1, 4, 5, 6), and a prospect with no significant mineral values (fig. 1, no. 3) were examined. A moderate potential for high-calcium limestone resources was estimated between ocurrences within the study area near McGraw and Spring Creeks (fig. 1, no. 2). There is low potential for copper resources at the Argenta Prospect (fig. 1., no. 1) in the study area, and the McDougall Prospect adjacent to the area.

Jan 1, 1983

By Curtis H. Elder

In studies conducted by the Bureau of Mines, two test areas were hydraulically stimulated and exposed by mining: One in the Pittsburgh coalbed at the Vesta No. 5 mine, Washington County, Pa.; and one in the Illinois No. 6 coalbed at the Inland mine, Jefferson County, Ill. Induced fractures were contained totally within the coalbed with no adverse effect on the stability of associated rock strata. Induced fractures were vertical and were propagated normal to the direction of least residual tectonic stress. Gas production was increased fivefold to twentyfold by hydraulic stimulation.

Jan 1, 1977

By M. M. Valenta

A number of challenges face platinum concentrator plant operators. These challenges include the increase in operating costs, the increase in smelter cost for the processing of concentrate, the shortage and cost of power, and the tightening of specifications on concentrate quality by the toll-smelting operations. Over the years the focus has moved from extracting the platinum group metals (PGM) from the Merensky Reef to the UG2 reef. This has a number of advantages, including the higher ?basket price? for UG2 concentrate, reduced mining cost per unit volume as a result of the higher density of UG2, and the reduction in overall concentrate tonnage to be smelted. In many cases the Merensky ore has been fully exploited and it makes sense for the focus to shift to the UG2 ore that can be accessed through the Merensky shaft infrastructure. The presence of relatively high levels of chromite in UG2 concentrate is, however, a major disadvantage due to the problems associated with smelting such a concentrate in conventional submerged arc furnaces. In addition to increasing the specification on the minimum PGM grade of concentrates, smelters have had to impose strict specifications on the levels of chromite in the concentrate. The threat of high penalties has forced concentrators to change their modus operandi, often resulting in a significant loss in recovery. The final concentrate grades and PGM recoveries are shown to vary significantly throughout the industry. The reasons for this include varying ore mineralogy and different operating philosophies. This would therefore imply that the opportunity exists to optimize the operations by considering fundamental aspects such as the PGM mineralogy and the application of appropriate technologies. By returning to the fundamentals of flotation and applying the findings of detailed process reviews, it has been possible to increase the concentrate PGM grade, reduce the concentrate chromite grade, and in some cases increase the recovery of PGM to concentrate. This paper presents case studies where this approach has been used to successfully optimize concentrator performance, resulting in lower operating cost and higher PGM production. Keywords Process optimization, platinum concentrator, milling, flotation, grade, recovery

Jan 1, 2011

By D. Pappas

Over the past decade the number of contractors working in underground coal mines has nearly doubled; however, the effect this has had on the industry?s injury rates has been the subject of much speculation. The confusion exists because the U.S. Mine Safety and Health Administration (MSHA) database does not assign contractor hours to the individual mining operations where they worked. To better understand the safety record of the contractor segment of the industry, the National Institute for Occupational Safety and Health (NIOSH) undertook a comprehensive analysis of the data contained in the MSHA database. The first part of the study compared overall contractor and operator trends from 1983 to 2009 related to employment, hours worked, injury rate, and days lost. One unexpected finding was that the larger contractors tended to have higher injury rates than the smaller ones. The second part of the study directly addressed the role of contractors on the safety record of 10 large underground coal mines. A detailed analysis provided both injuries and estimated contractor hours worked at these mines for the period 1992?2007. Comparison between the estimated contractor injury rates and the reported operator injury rates at these mines indicated that the contractor injury rates were significantly higher at most of the operations studied. However, the industry-wide data indicates that contractor and operator injury rates have converged since 2005 and are now equivalent.

Jan 1, 2011

By H. Kazemi, G. W. Thomas, M. S. Seth

The double-porosity model of Warren and Root7 for examining pressure drawdown and buildup phenomena in naturally fractured reservoirs has been extended to intetpret interference test results. Both analytical and numerical solutions are presented. The practicality of some of the assumptions in the Warren-Root model was also investigated. The standard procedure for interpreting interference tests in naturally fractured reservoirs beretofore employed an equivalent homogeneous reservoir model. A comparison of our results with the equivalent homogeneous model indicates the latter is inadequate for early time responses. For late time responses, however, the simpler equivalent homogeneous model yields favorable results. Finally, the effects of well spacing and the magnitude of the interporosity flow parameter are briefly cited. INTRODUCTION Interference tests can be used to provide reservoir information not obtainable from conventional pressure drawdown and buildup tests. The technique involves measuring the response in one or more wells arising from a pressure perturbation introduced into another well. It has been. successfully applied to single-layer, homogeneous, unfractured, isotropic and anisotropic formations to arrive at values of well storage capacity and a measure of directional permeability.l The techniques of interference testing usually can be extended to heterogeneous systems, provided the permeability contrast between any existing rock layers is not excessive.9 In such cases, the practical interference effects in an observation well of an interconnecting heterogeneous reservoir can be predicted using an equivalent homogeneous model. The calculated properties are then average values. Russell and Prats2 have demonstrated the utility of this approach for a single-phase, two-layer system. For naturally fractured reservoirs, some different approaches usually are necessary. The major departure from homogeneous or nearly homogeneous reservoir treatment is to characterize the fractured system as an entity having "double-porosity"; namely, we suppose the existence of both primary and secondary porosity, where the former is contained within a systematic array of identical rectangular matrix blocks and the latter is contained within an orthogonal system of continuous, uniform fractures (see Fig. 1). It is sufficient to assume that the permeability of the rock matrix is so small that movement of reservoir fluids to the producing wells is entirely through the fracture network. This assumption has been validated by Barenblatt3 and .employed by others?-7 Warren and Root7 used the double-porosity model to develop an interpretation of pressure drawdown and pressure buildup tests in naturally fractured

Jan 1, 1970

By Gary A. Kingston

Rolled steel, steel forgings, and steel castings in the Pacific Northwest (Washington and Oregon) are produced principally in the Seattle, Wash., and Portland, Oreg., metropolitan areas. Steel-mill products are rolled from carbon and some alloy &eels by three companies into shapes such as reinforcing bar, rods, rounds, squares, flats, and hot-rolled strips; structural shapes, - such as angles, channels, and I-beams, also are rolled. Carbon and alloy steel ingots are poured and forged at a Seattle plant into ship shafting, drive shafts, billets, slabs, bars, rings, hooks, and other items. Static, shell, investment, and centrifugal castings are produced at 19 steel foundries in a wide range of steel specifications. All Pacific Northwest steel output is based on remelting steel scrap. Local iron ore might be used in the future to supplement steel scrap as a metal source. Ore reduction would probably be achieved by methods other than the blast furnace. Current melt-shop practice and problems are basically the same in Pacific Northwest steel plants as in cold-melt shops in other parts of the country. Quality steel production is receiving more emphasis in this region with the installation of modern analytical equipment and vacuum pouring and melting facilities.

Jan 1, 1962

By James R. Aggson

This Bureau of Mines report describes floor heave ground control problems that have been encountered in a new underground coal mine in West Virginia. Previous experience in the coal seam, the results of physical property investigations, and in situ rock stress determinations are discussed. The apparent cause of the ground control problems is the existence of a high, biaxial, horizontal stress field coupled with a floor member that has time-dependent deformation characteristics, A theoretical analysis of the failure process is developed. The analysis is assisted by finite element techniques. Mine design recommendations based on this analysis are presented.

Jan 1, 1978

By Kevin M. Connor, Malcolm J. McPhersqn

Examples are presented in which Time Domain Reflectometry (TDR) was employed to locate deformation of rock masses induced by mining. The first example involved motoring the propagation of overburden fractures above a longwall coal panel and the second example involved the we of a)R to monitor rock mass deformation in the vicinity of a strip mine highwall. Bock mass deformation, strata separation and large block movement generated strains and failure along coaxial cables which were installed in drill holes and the TDR reflections generated by these strains and failures were monitored. Analysis of field data and a preliminary laboratory test indicate that it may be possible not only to locate rock mass movements but also to quantify these movements with TDR data.

Jan 1, 1984

By B. E. Blair

The physical properties and related geological and petrographic data for 81 rock types obtained from operating mines or selected test sites are presented in this report. Most of these rock data were obtained to supplement structural studies in underground mines; however, the data may be equally applicable to other problems where the physical properties of rock are an important factor. Stress-strain curves are presented, where available, and free medium velocities from laboratory and field measurements are compared for several rock types. Rock-type, geographical, and geo-logical indexes are included for reference relative to physical property data in this and previously published Bureau of Mines physical property reports. INTRODUCTION This report presents the physical properties of 81 rock types from 16 different projects (sections 53-68). Three previous physical property reports2 3 4/ (herein after referred to as parts I, II, and III) presented data on 244 rock types from 52 project areas. (Part I included sections 1-25, part II sections 26-36, and part III sections 37-52).

Jan 1, 1956