Search Documents

By A. M. Gaudin, J. H. Brown

In a survey of the effects of heat treatment on the comminution of various rocks, it was found that unusual size distributions often characterize the broken products, and that this is related to a great increase in intergranular fracture1. It is the purpose of the present paper to contribute to an understanding of this effect. In a thesis by one of use, critical consideration was given to many mechanisms which could conceivably be responsible for the increased intergran-ular fracture. It was shown that neither gross chemical changes nor intergranular corrosion are required. Among non-chemical mechanisms the most likely appeared to be (1) Uneven expansion due to thermal gradients, giving spalling (2) In a manner similar to that prevailing in metals, the appearance at high temperature of intergranular weakness. (3) Unequal thermal expansion of adjacent grains. Experiments were designed and conducted to permit a choice among the many alternative mechanisms and in particular among the three listed here. EXPERIMENTAL MATERIALS Tests were made on the materials listed in Table 1. Of each material, only lumps similar in composition and grain size were used. The three marbles listed in Table 1 were analyzed to assure that their chemical compositions did not differ greatly (Table 2). On the basis of the chemical analyses, of differential thermal analyses, and of X-ray powder diffraction patterns, it appeared that the marbles were very similar except for their grain sizes.

Jan 1, 1961

By R. Sankey, L. Gatty, F. Bizzozero, G. F. Shannon, F. Savaglio, L. McDonald

State mining regulations in Queensland stipulate that a mine be provided with an earth installed on surface and that all underground equipment that needs to be earthed should be connected via a copper conductor to this surface grounding point. The regulations further require that all exposed metal surfaces in underground substations be connected to an earth. In a study of earthing conditions at Mount Isa mine it was found that the physical anchoring of metal work at substations (with rockbolts and associated steel mesh) also provides an excellent electrical connection to the country rock. It was established that not only is the mine's earthing system grounded at numerous underground locations but also that such anchor points offer, in general, a path to ground with lower resistance than does the legally required grounding point on the surface. It is recommended that metalliferous mines should utilise a multiple-earth system and not a run earth connected to a single, above-ground earth point

May 1, 1991

By D. E. Wolfson

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The inherent suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests. According to the estimate of reserves by Dowd,3/ the recoverable coal in Floyd County in beds 28 inches or more thick, in thousand tons, is as follows: [ ]

Jan 1, 1958

By M. K. McCarter

Previous investigations suggest the possibility of determining shear strength of geologic materials by measuring the force necessary to rupture the web between two closely-spaced, parallel holes using a borehole jack. Current research using finite element modeling and laboratory testing of intact rock indicates that web failure initiates by tensile fracturing induced by a complex stress field. Based on these results, a theoretical justification for relating web strength with shear strength appears unlikely for holes of equal diameter spaced two diameters apart. Empirical results, however, show a strong correlation between average web strength and average unconfined compressive strength for some rock materials under laboratory conditions. A good correlation also exists between residual web strength and the residual angle of friction under the same conditions. This research project involves the construction and field testing of a large borehole jack. The jack is designed to operate within a conventional 12-1/4 inch rotary blasthole common to open pit mining. The system is capable of exerting approximately 800,000 pounds on curved platen measuring roughly 4x24 inches. Field tests indicate that the system will operate in a mining environment, and preliminary results suggest the possibility of using the force-displacement data generated by the jack to rank the competency of material within a mine bench.

Jan 1, 1982

By R. G. Warncke, D. Harrington

"INTRODUCTION The use of black blasting powder as an explosive in coal mines has long been recognized as hazardous and has been responsible for many of the worst disasters in American coal mines. One of the most pressing of the numerous problems confronting the Bureau of Mines, upon its creation in 1910 was to determine methods that would lessen the hazards created by the use of explosives in coal mines. The Bureau continued the study begun by the Technologic Branch of the Geological Survey as to the nature of explosives and made numerous tests to determine types of explosives suitable for blasting in coal mines. The Bureau has tested and approved hundreds of types of explosives and has disseminated information on methods and conditions for use underground to make them permissible as to safety. The Bureau of Mines has encouraged the use of permissible explosives for coal-mine blasting, and its experts both in the laboratory and in the field believe that the use of black blasting powder in any form (granular or pellet) is hazardous in any underground coal mine. Despite the information published at various times and innumerous ways and the general knowledge of the hazards that the use of black blasting powder in any form creates in the blasting of coal, the coal mines in the United States, during 1947 used approximately 34 million pounds of black blasting powder (granular or pellet), or approximately 11.8 percent of the total quantity of explosives used by the coal-mining industry.Many coal mines of the United States, for various and sundry reasons, probably will continue the use of black blasting powder, and this circular has been written for the benefit of such users, not that any suggested method or methods will make the use of this explosive safe, but it has been found that methods and conditions of use of black blasting powder can be improved so as to lessen, though not eliminate, the hazards created by its use."

Mar 1, 1949

By Clyde Baker

Drilled shafts for many situations offer an economical alternative to driven piles. The Federal Highway Administration (FHWA) has spent considerable time and money in research and developing design and construction guidelines for drilled shafts. However, the full potential of the technology may not be realized because of the uncertainty of the effects of construction on the actual service behavior and the lack of either reliable quality control tests to check for or evaluate defects, or inexpensive load test procedures. Static load testing is very expensive and it is not feasible to load test each shaft on a project. Therefore, other means are necessary to confirm or evaluate the integrity of the completed drilled shaft or to determine the capacity of the completed shaft.

Jan 1, 1989

By David Smith

Construction of a new transportation link frequently requires crossing under an existing highway or railroad. Although traffic diversions may permit a cut and cover structure to be built, ‘zero impact’ tunnel solutions are becoming increasingly popular. The vertical clearance between the new tunnel structure and the existing highway or tracks may be very low; sometimes less than two meters. This leaves little room for error since any ground loss can rapidly translate into surface settlement. Problems can be avoided by maintaining the stability of the tunnel face and by minimizing ground movement around the tunnel lining. This paper examines construction methods that have been used to construct short tunnels with shallow cover, and highlights factors to be considered for future projects.

Jan 1, 2005

By Charles E. Whieldon

Because of the importance of recovering more oil from known petroleum reserves, increased emphasis has been placed on the application of secondary-recovery methods. It is hoped that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases. Previously published reports3 4 5/ have described the results of water-flooding in Roane, Pleasants, and Wetzel Counties, W. Va. (fig. 1). This report describes the South Penn Oil Co. Yawkey waterflood property, Berea sand, Griffithsville oilfield, Duval District, Lincoln County, W. Va. (fig. 2).

Jan 1, 1961

Reduce the danger to personnel and destruction of equipment caused by fires on surface coal augers. Approach: A reasonably priced reliable system which automatically senses a fire and activates dry chemical extinguishers, has been built and field tested. How It Works: Heat sensors mounted in the engine compartment and hydraulic hose areas detect the fire, usually before the operator does. This causes the system to automatically discharge A-B-C class dry chemical extinguisher through a fixed piping system.

Jan 1, 1976

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag composition. Liquidus and solidus temperatures and solid solubilities were determined for the BaF2-Y203 system, and the information is presented as the phase diagram. The phase diagram was constructed from data obtained by ceramography, X-ray diffraction, and thermal analysis of specimens encapsulated in small molybdenum ampoules. The data indicate a simple eutectic system with maximum terminal solid solubilities of less than 1 mole pct. The eutectic temperature is 1,343° C, and the composition of the eutectic is less than 1 mole pct Y203.

Jan 1, 1970

By M. D. Riegel, Brian T. Felber

"Construction of foundation elements in an urban environment is often complicated by multiple constraints such as existing foundations, utility conflicts, maintenance and protection of traffic on high volume roadways, low overhead clearances, and vibration and displacement monitoring to reduce risks of impact to existing facilities. Micropiles are commonly a preferred foundation alternative in an urban setting to mitigate some of these risks. This paper presents examples in which micropiles helped reduce risk in an urban setting on the two subject infrastructure improvement projects. The case studies presented include the Verrazano Narrows Bridge HOV and Bus Ramp Improvements in Brooklyn, NY and the Kosciuszko Bridge Replacement in Queens and Brooklyn, NY. The paper details the micropile design, how risks were mitigated, and the complications to each of these projects associated with the urban setting.INTRODUCTIONThe paper begins with background information about the Verrazano Narrows Bridge HOV and Bus Ramp Improvements Project, followed by background information for the Kosciuszko Bridge Replacement Project. This introductory background information is followed by discussion of the urban site constraints, which controlled the foundation type selection for both projects. In closing, the paper discusses the micropile design process, load testing, and construction.VERRAZANO NARROWS BRIDGE HOV & BUS RAMP IMPROVEMENTS BACKGROUNDProject ScopeThe project consists of two new ramps; one designated for HOV / Bus traffic between Staten Island and the Gowanus Expressway, and one to be utilized for storing the barrier transfer vehicle. Also included is the complete reconstruction of Ramps B and F to accommodate horizontal and vertical alignment clearances from the new ramps, removal of the median of the upper level to add one lane, utilities improvements, stormwater improvements, and miscellaneous structural repairs. The new HOV / Bus Ramp was designed for reversible traffic flow to accommodate the demand of the peak traffic direction by movable barrier.Geotechnical / Foundation Engineering ScopeThe geotechnical work included a desk study review of existing plans, geotechnical reports, and geologic maps. This data was subsequently supplemented with a subsurface exploration program. Once completed, foundation design was performed for 25 proposed bridge substructures. Four existing battered pilesupported foundations and two shallow foundations were evaluated for increased loading. Upon completion of the foundation design, foundation plans, specifications, and an engineer’s estimate were prepared. Foundation installation was observed on a part-time as needed basis."

Jan 1, 2016

By Frank P. Frandina, Michael J. Loehr, Paul E. Gabryszak

The Heartland Corridor Clearance Improvement Project is part of a regional Public-Private initiative to allow double stack container trains a direct route from the Port of Norfolk through Virginia, West Virginia, Eastern Kentucky and into Central Ohio. In the Preliminary Engineering stage, 30 existing tunnels were assessed and 28 were found to need clearance improvements to allow the use of double stack trains. Alternative tunnel enlargement methods were developed to achieve the desired clearance improvements, while maintaining structural integrity and minimizing disruption to train traffic. This paper summarizes the geometric and condition investigations of the existing tunnels, as well as describes the preferred methodologies to achieve the desired clearance. The clearance improvements will be implemented beginning in the summer of 2007.

Jan 1, 2007

By R Munoz, R González, J Vallejos, A Delonca

In panel caving in underground mines, it is essential to characterise and monitor the stress and stability state of production level pillars to ensure the extraction of the mineralised ore column and the safety of workers. Pilar Norte is a sector in the El Teniente mine that forms a pillar between the undercut fronts of the adjacent Esmeralda and Reservas Norte sectors. It exists in a high-stress environment, which may induce damage to the rock mass production pillars. Generally, numerical models are calibrated using observed damage in galleries. This procedure does not discriminate between the structural condition and/or the blasting damage effects. This paper proposes a technique that uses borehole cameras to measure stress-induced damage. This has the advantage of being at the intact rock scale, meaning that the effect of geological structures is negligible and the blasting damage factor is eliminated. Comprehensive geotechnical characterisation and tomography monitoring has been undertaken at Pilar Norte to describe and determine the rock mass behaviour of the production pillars. By combining analytical, empirical and numerical models, a correlation between the measured overbreak recorded by the borehole cameras and the stress level of the pillar was developed. The methodology can be routinely applied to estimate the stress state in the production pillars.CITATION:González, R, Munoz, R, Vallejos, J and Delonca, A, 2016. Characterisation and monitoring of the stress state of production pillars at El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 197–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By D. Arentsen

Changing environmental laws, new operating requirements and the increasing accuracy with which the bearing capacity of driven piles can be calculated have all led to the development of hydraulic piling hammers, some very primitive, others very advanced. Users find it difficult to decide which model is the most suitable, because the specifications are neither uniform nor unamiguous. There are no standard specifications and, moreover, the majority of hammers are suitable only for a limited range of applications. For the user, however, it is important to choose a hammer which will meet future as well as current requirements and will not quickly become obsolete or be unsuitable for a particular job.

Jan 1, 1987

By B. J. Moore

This publication contains analyses and related source data for 269 natural gas samples from wells and pipelines in 18 States. All of the samples were obtained and analyzed during, calendar year 1979 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576.3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the general public. Twenty-one previous publications have presented tine results of 11,883 gas analyses made prior to 1979. The first three, Bulletins 486,4 576,5 and 617,6 contain analyses and related source

Jan 1, 1980

By Stephen C. Tadolini

PC-Strand tendons, commonly referred to as cable bolts, have become a major rock reinforcement device for underground mining and civil applications. The most common configuration is a 1+6 strand, which designates a center king-wire, with six outer wires wound around it to form a 0.6-in (15-mm) diameter cable. The capacity of this tendon approaches 30 tons, but the performance is largely dependent on the anchorage medium and the ability of the system to transfer stresses back into the rock mass while reinforcing and suspending the immediate roof. Recent developments to improve the transfer mechanisms of the PCstrand via the anchorage medium by impregnating the individual wires with uniquely designed deformations have resulted in improved anchorage and subsequent cable bolt performance. This paper describes a series of laboratory tests used to develop the initial indentation patterns and numerical modeling simulations that were undertaken to refine and optimize the final designs. The new, indented PC-Strands, offered in both bright and properly galvanized, have been tested in the field and are being used effectively in two new cable bolt products. The results of the laboratory, computer modeling, field testing and in-situ installations provide a glance at the next generation of cable bolts. This suite of testing shows how they will improve the safety and serviceability of openings under adverse ground conditions.

Jan 1, 2012

By J. M. Singer

In this Bureau of Mines study coal and rock dust beds were entrained by airblasts generated by gas explosions at the closed end of a 0.61-m-diameter explosion tunnel, 49.7 m long. The system was designed to simulate entrainment of mine dust deposits by accidental gas explosion at the coal face of nonintersecting mine passageways. Full-scale mine explosion trials confirmed many of the results of the explosion tunnel experiments and indicated several new features of dust entrainment. Dispersal of 20.3-cm-long stepped dust beds located 35 m from the closed end always began during the early portion of the ascending gradient of the first transient airflow (and pressure) wave, and was usually completed before the end of the first quarter-wave period. Bulk quantities of dust were entrained simultaneously by longitudinal regression from the leading edge of the dust bed and by surface lifting of the top layer. Instantaneous threshold air velocities for bulk quantities of coal and rock dust beds in separate, mixed, and layered configurations were in the same range (5 to 30 m/sec) as previously found under steady-state velocity conditions. Selective lifting of coal dust layers from rock dust occurred when the threshold dispersal velocity of coal dust but not of the underlying rock dust was exceeded.

Jan 1, 1976

By Allan E. Martin

As part of a comprehensive investigation of tae mechanism of desulfurization of iron and steel by slags, the Blast Furnace Studies Section, Metallurgical Division, Bureau of :lines, in cooperation with the Institute of Technology., University of Minnesota, has made a study of the forms in which sulfur occurs in blast-furnace slag. This report presents data on the three sulfides most important in iron smelting, namely, ferrous sulfide, manganous sulfide, and calcium sulfide. The tendency of these sulfides to form colloids in the molten slag was determined by an examination of quenched samples with an ultramicroscope. Vogt5/ conducted experiments on sulfide silicate melts and examined synthetic blast-furnace slags in a partly crystallized condition. His conclusions were that FeS, CaS, and MnS, or isomorphous compounds, such as (FeXCay)S and (MnxCay)S, were precipitated from the melt, depending on the composition of the slag. In all specimens sulfides were visible and were spherical.

Jan 1, 1941

By S Lush, R Polglase

McConnell Dowell is pleased to be given the opportunity to present two papers to this conference. The first is a general discussion paper on our work in the field of slurry transportation. The second will be a technical paper on the development of a welded coupling compatible with urethane lined pipework. We trust that by discussing our recent work we can leave two lasting impressions on you: the versatility and useful role of slurry transportation, and the leading role taken by New Zealand in this technology This paper discusses three recent projects the New Zealand Steel Ironsand Transfer Line the Coarse Coal Ship Loading Technology the Nerang River Sand By-pass System. These have followed on from the other slurry projects with which McConnell Dowell has been associated such as the ironsand export trade at Waipipi and Taharoa. The New Zealand Contractors Federation awarded the Construction Award for 1986 to McConnell Dowell for the Ironsand Slurry Pipeline.

Jan 1, 1986

By D A. Edmunds

The most important development that has been taking place recently relating to mining operations in New Zealand would generally be regarded as being the Resource Management Law Reform. This has been widely publicised by the Government as a comprehensive review of the laws governing New Zealand's natural and physical resources. Submissions have been sought and a free phone provided to encourage public participation. Recently a Discussion Paper has been prepared by the Core Group coordinating the review to explain progress on Phase One (Ministry for the Environment, Directions for Change: A Discussion Paper, Wellington 1988). It outlines Government decisions already taken which impinge on the Review and describes the possible models for resource management laws. However, it is possible that some fundamental practical issues of significance to the mining industry will not be addressed and may be lost sight of in the much wider issues which are to be covered. The purpose of our paper is to address one of these issues namely, the interrelationship between any new resource management legislation and the Conservation Act 1987 (as recently amended) in the context of Ministerial consents. The importance of this issue can be seen from the fact that as at 7 June 1988 there were 279 mining licence applications and 223 prospecting licence applications waiting to be determined by the Minister of Conservation. Since April 1987 only 19 mining and 13 prospecting licences have been consented to. In addition a major proportion of New Zealand's mineral resources are contained with land administered by the Department.

Jan 1, 1988