Search Documents

By Arash Khosravifar, Matt Steffan

An expansion of the City of Klamath Falls Wastewater Treatment plant required geotechnical seismic hazard evaluations and deep foundation design. The site is located on the shore of Lake Ewauna and is underlain by diatom rich lake deposits. Diatomaceous soils exhibit unique engineering properties that are not well understood. Cyclic Direct Simple Shear (CDSS) testing was performed on three undisturbed samples to evaluate cyclic and post-cyclic properties of the diatomaceous soils. Results from the CDSS testing indicated that the soils would not liquefy in the classical sense, though cyclic softening behavior was observed. The CDSS results were used to develop a Cyclic Resistance Ratio curve for the diatomaceous soil to compare with clean sand liquefaction curves. Seismic lateral pile capacities were developed using two approaches. One approach used conventional p-multipliers for liquefied soil and modified them to reflect expected excess pore pressure ratios. The other approach applied residual strength and fifty percent strain values from post-cyclic monotonic shear testing. A lateral spread hazard zone was identified along the Lake shoreline and reduced, seismic lateral pile capacities were recommended. The objective of this paper is to report the seismic design considerations for this project in a unique geologic and seismic setting. INTRODUCTION The engineering properties of diatomaceous soils have rarely been studied and the cyclic behavior under seismic loading is generally unknown. Some of the critical geotechnical uncertainties of diatomaceous behavior include potential for large consolidation settlement, influence of irrecoverable strains due to diatom particle crushing, shear strength (peak and residual), and cyclic properties. This paper presents results of cyclic shear testing, seismic evaluations and seismic lateral pile design in diatomaceous soils performed for the expansion of a waste water treatment plant in the city of Klamath Falls, Oregon, site of the largest recorded earthquake in Oregon’s history. The expansion consisted of adding six new facilities at the existing Plant including influent pump station (IPS) and headworks, aeration basin, tertiary treatment, and other buildings. The IPS/headworks and aeration basin will be founded approximately 15 feet below ground. The other buildings will be founded at grade. The existing facilities are supported by timber piles that penetrate the surficial diatomaceous soils and terminate on a hard underlying deposit. Figure 1 shows the site plan and proposed additions.

Jan 1, 2018

By Robert Bachus, Jamey B. Rosen

"Abstract Large scale In Situ Barrier Wall Construction projects, specifically those related to earth dams, dikes, and levees, frequently require stringent quality control measures to ensure the success of the wall. This presentation discusses the applications of Geographic Information Systems (GIS) technology to capture information from multiple data streams and provide geotechnical feedback, quality control, and project control feedback. Techniques used to geospatially analyze verticality data from secant piles and panels will be demonstrated. Examples will be presented from barrier wall installations at two sites owned by the U.S. Army Corps of Engineers (USACE): the Wolf Creek Dam in Kentucky, and Center Hill Dam in Tennessee.IntroductionDeep foundation installations require contractors to collect a substantial amount of information over the course of a project, both for internal quality control of construction progress and for demonstrating compliance with customer or owner specifications. Methods of collecting information are constantly improving, bringing with it the need for a systemic approach to managing the increasing amounts and types of data. Handling these diverse types of data presents challenges with both budget and schedule demands. This paper discusses some techniques for adding or increasing quality control in barrier wall constructions by consolidating, visualizing and analyzing data using relational database and Geographic Information Systems (GIS) technology, collectively referred to as Information Management System (IMS) development. The IMS concept is designed to facilitate the collection, transfer and processing of data and provide an easy way to remotely access and visualize construction progress.The remainder of this paper presents the needs and objectives of an IMS applied to quality control in barrier wall construction, the components and data flows involved, the capabilities and user interfaces of the systems and the benefits for the end users. Examples are presented throughout from case study projects including: a pile barrier wall applied in the rehabilitation at the Wolf Creek Dam in Kentucky (under contract to the Treviicos-Soletanche Joint Venture), and a secant pile barrier wall currently under construction in the rehabilitation of the Center Hill Dam in Tennessee (under contract to Bauer Foundations Corporation) (both owned by the Nashville District of the USACE)."

Jan 1, 2014

By Willie M. NeSmith

Conventional augered, cast-in-place (ACIP) piles were introduced into the New York City area as a result of the damage to existing structures caused by pile driving operations. ACIP piles are often specified where deep foundations are to be installed adjacent to transit facilities, sensitive underground utilities or in close proximity to existing structures. However, loss-of-ground issues associated with the installation of ACIP piles have prevented the wide-scale use of these systems. Beginning in 2002, Berkel & Company Contractors, Inc. began using its augered, cast-in-place displacement (ACIPD) system in the New York City area. Like conventional ACIP piles, this system produces almost no vibration. Also, as almost no material is brought to the surface, there is no opportunity for loss of ground. This paper presents a description of Berkel's displacement pile system and a brief discussion of six projects in the New York City area that have been executed with this system over the past two years.

Jan 1, 2004

By Peter N. Calder, J. L. Workman

There are many opportunities for computers to assist in dragline mine planning. Three important areas particularly lend themselves to computer assisted study. These are overall mine design and planning, the computation and display of range diagrams and the calculation of production and production variability. The computation of range diagrams is of particular interest because of the importance of matching the dragline and site geometries. This paper examines the uses of range diagrams in dragline mining and illustrates the application of computer techniques to the computation using one such program as an example. The use of computer generated range diagrams for machine selection, pit design and in parameter analysis is discussed. Directions for further development are also provided. There is a great deal that can be done to additionally enhance the ability to provide accurate designs for the dragline operation. One area that needs special attention is the dumping of overburden around access ramps into the pit. This situation is one of the most difficult dumping sequences and affects machine selection and pit operation. It is also suggested that programs that simulate the production schedule of the drag-line would be useful. It is concluded that large overall mine planning programs are very important in dragline mining. However, smaller programs designed for a specific, task are also important tools in many cases. These are easy to learn and use, well adapted to the PC environment and provide useful information, both for design and for daily planning.

Jan 1, 1989

By S Wright, W Bruckard

The current status of battery collection and recycling schemes in Australia are explored in light of current developments in product stewardship and increasing pressure to decrease materials going to landfill by originating equipment manufacturers. Used consumer batteries, both single cycle and rechargeable contain a mixture of valuable metals and potentially toxic materials that may become a resource/revenue stream to offset the cost of disposal/recycling. Although the volume of batteries discarded in Australia is modest compared to other global population centres, the expected increase in battery use with increasing equipment portability and future developments in the automotive industry, provide an opportunity to recycle. The requirements for a battery recycling facility in Australia and the most promising processing platforms that may exploit the resource with enough flexibility to cope with battery developments and market trends, are explored.

Jan 1, 2006

By Y. Bai, J. J. Liu, D. Q. Li, S. Z. Liu, X. T. Wang

"This paper presents the results of an industrial test using 8 t/d of Baotou concentrate (50% REO) of a clean metallurgical process, which includes: 1. Roasting with H2SO4 at low temperature (220~260 0C) in a batch roasting furnace followed by water leaching to obtain a leach liquor as feed with a yield of >95% RE and Th, recovering F as fluoride, producing a leach residue amounting to 1/3 of an equivalent high temperature residue and containing <0.03% Th and radioactivity < 3×104 Bq/kg compared to the normal high temperature residue containing 0.2-0.3% Th and 1×105 Bq/kg. 2. Separating Th with N1923 and extracting RE by P507 has been completed in mixer-settlers. Test results indicate that the ThO2 product has a purity of > 95% with a yield of 99%, and the RE has a yield of >95%, in which ThO2/REO <5×10-6, and that P507 loaded RE connect straight with separating RE using P507-HCl system. 3. Treatment and multipurpose use of "three wastes" (water, gas and solids) are discussed in some detail."

Jan 1, 2014

By W. P. Tassie

"The location of Quintette Coal Limited&apos;s pit and geologic nature of the dedicated reserves combine to introduce a number of factors which can adversely affect waste dump stability. These factors include steep terrain, variable material type and particle size, and precipitation. This paper describes the solutions to related waste dump problems. A brief geotechnical review of the waste dumps is given and Quintette&apos;s operational strategies during periods of dump stability and instability are discussed. Despite best efforts, failures occasionally occur and discussion is included on Quintette&apos;s success at bringing failed dumps safely back into use. IntroductionQuintette Coal Limited (QCL) property is situated on the east slope of the Rocky Mountains near Tumbler Ridge, approximately 120 km southwest of Dawson Creek, British Columbia. This surface mine is located on mountainous terrain and is subject to climatic extremes of wind, precipitation and temperature.QCL has a current annual production of 4.75 million tonnes of metallurgical coal with a stripping ratio of 7: 1. This correctly implies the extraction of over 33 million bank cubic metres (BCM) of waste which is placed on numerous waste dumps at various locations adjacent to the pit.There are three active pits - Mesa, Wolverine, and Shikano (Fig. 1). Shikano is a newly developed pit located near the plant site. It is not subject to the unique dump management problems prevalent at the Mesa and Wolverine pits, therefore the Shikano waste dumps will not be discussed . The dumps for the Mesa and Wolverine pits, however, have been technically and operationally challenging since shortly after mining began in 1983. Their characteristics, associated site specifics and management, therefore, are the subject of this paper.Waste dump locations for the Mesa and Wolverine pits are shown in Figures 2 and 3 as is the relative waste distribution . Each sub-pit is connected to a principal waste dump in reasonable proximity and to an alternate dump should disposal of waste be necessary at that location. The waste dumps are constructed from the top elevations initially to coincide with subpit development. In the initial years (1-7) waste dump heights will be up to 250 m, then, as the mine matures (8-20 years), waste dump maximum heights will continuously decrease to coincide with lower bench elevations"

Jan 1, 1988

By Jon C. Volkwein

The U.S. Bureau of Mines conducted a study to assess the impact of a directional water spray system on a unique single inlet dust scrubber on a low-profile mining machine. Tests were conducted in a full-scale model mine using a continuous mining machine. Tracer gas was introduced at the face and concentrations of the tracer gas were monitored at the face and in the return. Various parameters tested included mining position, depth of cut, brattice setback, and combinations of scrubber, and directional or symmetrical sprays. Results indicated that either water spray configuration improved the ventilation effectiveness of the scrubber by a factor of 2 to 3. Average face ventilation effectiveness (FVE) values for all testing of the scrubber and directional sprays were 0.95, versus 0.37 for a standard 20-ft blowing curtain without sprays. No FVE values were less than the standard 20-ft blowing results.

Jan 1, 1989

By Frank Cappuccitti, James A. Finch, Stéphanie Gélinas

"A colorimetric technique, originally developed for methyl iso butyl carbinol (MIBC) based on the Komarowsky reaction, has been extended to a wide range of common mineral flotation frothers. The procedure, which is briefly described, is shown suited to on-site determinations in a campaign at Kennecott Utah Copper Copperton Concentrator (Rio Tinto). Some observations are described, including: frother (MIBC) concentration evolution down a bank, frother distribution between pulp and froth phases, and loss of frother over time due to adsorption on certain minerals. A possible interference with a fuel oil addition was overcome. MIBC in recycle water was also measured.The ability to monitor frother easily will help interpret gas dispersion behaviour and should permit further optimization of flotation cell hydrodynamics and chemistry. The capability to directly measure should help optimize the type, amount and location of frother addition, and to assess frother recycled with reclaim process water.INTRODUCTIONOwing to the lack of analytical methods, the task of determining frother concentration in plant flotation circuits is not routinely performed. Industrial sites seldom outsource analyses that are both costly and inconvenient, due to the necessity of shipping freeze-dried samples to remote testing facilities. A more direct colorimetric method has recently been demonstrated for the laboratory characterization of common industrial frothers (Gélinas and Finch, 2004). The approach, based on the Komarowsky reaction (Penniman et al., 1936; Coles et al., 1942; Duke, 1947), was previously described by Parkhomovski et al. (1976) for methyl iso butyl carbinol (MIBC). The reaction involves the interaction of the OH group of a higher alcohol, concentrated sulphuric acid, and salicylaldehyde, to yield coloured solutions with intensities that can be analyzed by UV-visible spectrophotometry."

Jan 1, 2005

By E. R. Maize

This report is the second of a series on roof movement in coal mines. The first (R. I. 3355)4/ dealt with convergence of roof and floor and movement of the surface accompanying and following extraction in a mechanized mine in which retreat of rib lines was rapid. The studies reported herein were made in a mine in which all the coal is loaded by hand, and movement of the rib lines was much slower in consequence. In choosing a site for this work, it was decided that the mine selected should have natural conditions akin to those of the first study and entirely different methods of working. To this end a cooperative agreement was made with the Crucible Fuel Co. through W. J. Whitaker, secretary, for conducting the work in the company&apos;s Crucible mine, operating in the Pittsburgh bed in Greene County, Pa. This paper gives an account of the methods used in the investigation, excerpts from the data obtained, and such generalizations as can be made.

Jan 1, 1939

By E. R. Maize

This report is t e second of s series on roof movement in coal mines. The first (R. I. 3355)4/ dealt with convergence of roof and floor and movement of the surface accompanying and following extraction in a mechanized mine in which retreat of rib lines was rapid. The studies reported herein were made in a mine in which all the coal is loaded by hand, and movement of the rib lines was much slower in consequence. In choosing a site for this work, it was decided that the mine selected should have natural conditions akin to those of the first study and entirely different methods of working. To this end a cooperative agreement was made with the Crucible Fuel Co. through W. J. Whitaker, secretary, for conducting the work in the company?s Crucible mine, operating in the Pittsburgh bed in Greene County, Pa, This paper gives an account of the methods used in the investigation, excerpts from the data obtained, and such generalizations as can be made.

Jan 1, 1939

By A. D. Ajak

A complete mining cycle involves digging, loading, hauling and dumping of the materials. Moving the ore from the pit to the crusher or to the waste dump requires access routes, which are termed haul roads. These roads have to be designed, constructed and maintained. A review of the literature indicates a common consensus among researchers that there should be a balance between haul road economics and safety of the road users. However, there is no universally accepted theory on the design of haul road geometry and, in particular, road dimensions. The current industry practice is based on empirical data and rules of thumb developed by engineers. Therefore, this paper will use the overlooked and less valued branch of mathematics, arithmetic progression, to derive a road width equation. It is beyond the scope of this paper to discuss all road design components. The focus will be on the geometric aspects, which more often have a direct impact on road safety. In this paper, the current design practices and techniques for haul road geometrics design will be explored, using arithmetic progression to formulate road width equations, case examples to apply the equation and then validating the results with conventional techniques that have confirmed the reliability of road width equations, thus eliminating use of tables during design.

Jan 1, 2012

By Peter O. Wilkinson

Ascot Racecourse in the UK is a major international venue for horseracing. The racecourse is being redeveloped to provide entirely new public facilities. The development includes the construction of a new grandstand. A site investigation was earned out comprising mainly cone penetration testing. The site is underlain by the Bagshot Formation, comprising predominately cohesionless deposits of medium dense becoming dense, silty fine to medium sand, containing occasional layers of clay. Shallow foundations would present uncertainty regarding total and differential movement; hence a piled foundation solution was chosen using a continuous flight auger (CFA) piling system. The possibility that piles may found either directly on or within the influence of cohesive material suggested uncertainty regarding toe resistance. In order to measure shaft friction, an instrumented preliminary test pile was undertaken. The results were compared to published correlations of cone and shaft resistance. This approach resulted in a net saving in terms of pile length which resulted in optimum value engineering and hence a cost saving to the client.

Jan 1, 2006

By A. J. MacRae

Metallurgical furnaces are made up of complex multi-component systems that must function either together or in parallel for safe, and reliable operation. Thermal expansion of single material components experience induced stresses during heating and cooling, which can lead to cracking or failure. Multi component elements and systems can experience significant thermally induced stresses during both steady state and transient temperature conditions. Examples pertaining to temperature effects on refractory, copper cooling blocks, furnace shells, and complete systems will be discussed. The purpose of the paper is to highlight how stresses and strains are developed due to differential thermal expansion.

Jan 1, 2015

By P. J. Sylvester, D. H. C. Wilton, R. I. Wheeler, M. A. E. Huminicki, D. Evans-Lamswood

"Systematic characterization of the mineralogy of massive sulfide ore deposits can provide valuable insights into ore genesis and metallurgical processing that would not be apparent otherwise. We describe a method wherein (1) normative mineral abundances are calculated from whole-rock chemical assays using an algorithm, (2) the results are cast in block models, (3) the results are then verified with automated image analysis of a subset of samples prepared as grain mounts by backscattered electron imaging and X-ray mapping on a scanning electron microscope, and (4) those verified results are integrated with textural data determined by optical microscopy.The technique is applied to the magmatic Ni-Cu-Co sulfides of the Ovoid orebody, based on geochemical assays of 3175 whole-rock samples. Three principal ore zones are defined in the Ovoid. Type I ore occurs in the center of the deposit; it is magnetite-rich and pyrrhotite-poor with intermediate contents of pentlandite and chalcopyrite. Type II ore surrounds Type I ore and is pentlanditechalcopyrite- rich with intermediate contents of pyrrhotite and magnetite. Type III ore occurs at the base and along the outer periphery of the northern part of the orebody; it is pyrrhotite-rich and chalcopyrite- poor with an intermediate content of pentlandite, and a low-to-intermediate content of magnetite. La caractérisation systématique de la minéralogie des gîtes de sulfures massifs peut fournir des indications précieuses sur la genèse des minerais et le traitement métallurgique qui ne seraient pas disponibles par d’autres méthodes. Nous décrivons un procédé par lequel (1) un algorithme est utilisé pour calculer l’abondance de minéraux normatifs à partir d’analyses lithogéochimiques, (2) les résultats sont exprimés dans des blocs diagrammes, (3) les résultats sont par la suite validés par analyse d’image automatisée sur un microscope électronique à balayage en électrons rétrodiffusés et par cartographie en rayons X sur des échantillons constitués de grains montés en résine, et (4) les résultats de cette validation sont combinés aux données texturales obtenues par microscopie optique.Cette technique est appliquée aux sulfures magmatiques de Ni-Cu-Co du gisement Ovoïde, en utilisant les analyses géochimiques de 3175 échantillons de roche totale. L’Ovoïde comprend trois types de minerai. Le type I est situé au centre du gisement; il est riche en magnétite et pauvre en pyrrhotite avec des quantités intermédiaires de pentlandite et de chalcopyrite. Le minerai de type II entoure le minerai de type I et est riche en pentlandite et en chalcopyrite avec des quantités intermédiaires de pyrrhotite et de magnétite. Le minerai de type III se trouve à la base ainsi qu’à bordure externe de la partie nord du gisement; il est riche en pyrrhotite et pauvre en chalcopyrite, avec un contenu intermédiaire en pentlandite et une quantité faible à moyenne de magnétite."

Jan 1, 2012

By Martin Herrenknecht

The world?s growing population and rapidly proceeding urbanization are boosting an enormous demand for new and high-capacity infrastructures to secure the mobility of goods and people. Densely populated areas face the challenge to provide efficient traffic infrastructure, such as a modern public transportation system. At the same time, the maintenance and modernization of supply and disposal structures for water, sewage, energy and communication are also essential. Additionally, supra-regional transportation routes such as long distance water diversion schemes are the challenges for the future. All these projects are as demanding as they are characterized by a tight time schedule.

Jan 1, 2010

Open pit mine plans define the complex strategy of displacement of ore and waste over the mine life. Various mixed integer linear programming (MILP) formulations have been used for production scheduling of open pit mines. The main problem with these models is the inability to solve real size mining problems. We present a mixed integer linear programming formulation for the open pit long-term production scheduling problem. To reduce the number of binary integer variables in the formulation, we aggregate blocks into larger units referred to as mining-cuts. We present a semi-supervised clustering algorithm which aggregates smaller blocks based on rock types and grade ranges into mining-cuts without introducing an error in the grade estimated values. The cluster-based aggregation algorithm is fully integrated into an MILP mine production scheduling prototype software. We have implemented, verified, and validated our models. The efficiency of the new platform is evaluated through iron ore mine case study.

Dec 6, 2010

Ventilation network modeling in mine planning dates back at least three decades, but it is not widely accepted and/or practiced until the last decade, thanks to the advent of modern computers with their increase d speed and storage space. There are at least half a dozen such modeling software packages available on the market each with different features and acceptance. This paper compares five popular software packages,?? VnetPC Pro, MineVent, VentSIM Visual, VentGraph and MFIRE 3.0. A case study using Missouri S&T?s Experimental Mine is conducted to compare the five software packages in features, interface, output display and user-friendliness.

Jan 1, 2012

By S. Slottee

The technology of making and using ?paste? from mine tailings is increasingly well known by the minerals industry. The primary applications are water recovery and ?stacking? of tailings with minimal use of dams and ponds. This paper highlights some applications, other than water recovery and stacking, that have come to the attention of a paste thickener equipment supplier. As generated by thickeners, paste (also called ?thickened tailings?) is a non-settling, relatively high concentration, suspension of solids that can be pumped. Paste deposits with an angle of repose, allowing minimal use of dams. High solids concentration allows more water recovery at the paste thickener than is achieved in conventional and high rate slurry tailings thickeners. This paper is based on paste as produced in a flow sheet that includes a thickener, underflow pumps that are typically centrifugal, transfer pumps that can be centrifugal or positive displacement, and a distribution system at the deposition site. Examples of paste applications other than water recovery or stacking include: ?mine? an existing tailings pond by removing slurry, recovering coal or iron ore values, and return the new tailings to the pond as a paste that does not res-suspend; use paste to seal an existing tailings pond from leaking to groundwater or to an underground mine; extend the life of an existing tailings pond by thickening the tailings to paste; move an existing dry tailings impoundment to a new location by slurrying, pumping, paste thickening, and redeposit; minimize the size of a filter by paste thickening the feed; operate a paste thickener and filter in parallel on a tailings stream with re-mixing to achieve a high solids concentration. The use of paste tailings technology has been expanding over the last 15 years. The applications, both implemented and under consideration, are increasingly diverse and include all minerals tailings. Tailings handling designers should always consider a paste option to the conventional slurry solution.

Jan 1, 2011

By Alex Cormode, Carlos Perucca

"Sylvinite ore from the Saskatoon area typically contains about 5% insolubles, occurring as clays and carbonates. These insoluble slimes must be removed sufficiently well to permit an efficient subsequent potassium chloride flotation, due to their high adsorptive capacity for amines used as potash collectors. The insolubles are liberated from sylvinite by high attrition scrubbing in a slurry. The liberated slimes are separated by multistage cycloning or by a selective flocculation-flotation process.An outline of the potash processing operations at Agrium Vanscoy Potash Operations is given, emphasizing the insoluble slimes froth flotation separation process. This process was originally implemented at the Agrium plant in the mid- 1970's and replaced a hydrocyclone system.IntroductionAgrium Vanscoy Potash Operations is located 40 Km southwest of Saskatoon, almost midway between the communities of Vanscoy and Delisle. Processing operations started in 1969, and the annual production capability was subsequently increased to the current 1.8 MM tonnes per year of muriate of potash.The mining operation at Agrium Potash which was described in a paper by Jones and Pruggerl , is done underground using four large continuous double rotor boring machines for the main production with development done by heliminers. Annual ore production is 5.5 MM tonnedannum. Ore is hoisted 1,100 m to surface for processing."

Jan 1, 1999