Search Documents

By J. Miller, B. Slaker, M. M. Sears, G. Rashed

Ground falls represent a significant hazard at underground mines in the stone, sand, and gravel (SSG) sector in the USA. Researchers from the National Institute for Occupational Safety and Health (NIOSH) are currently conducting detailed investigations into the complex loading conditions at underground stone mines operating in challenging conditions. This paper presents the application of numerical modeling to analyze pillar and roof stability at a dipping underground limestone mine. A validated numerical model was used to explore the potential behavior of the pillars and roof as loading conditions change. The validated model was used to compare changes in mining sequence, overburden depth, and the in situ stress field. This will allow mine operators and engineers to have a better idea of the conditions that could be encountered as mining progresses. Results from the numerical modeling indicate that roof displacement more than doubles as the vertical stress increases from 10 MPa (1450 psi) to 19 MPa (2750 psi) when the maximum and minimum horizontal stresses were 41 MPa (5950 psi) and 22 MPa (3190 psi), respectively. Consequently, as the pillar load increases, the safety factor of the pillars is projected to decrease by about 25%. The impact of the practical application of numerical models can result in a reduction of ground-fall accidents and injuries as well as generally safer working conditions.

Feb 2, 2021

By M. Kamyab

The Deep Exploration Technology project, as part of the Australian Cooperative Research Centre, is developing technologies to drill deep boreholes for mineral exploration purposes. The aim of the initiative is to transfer drilling technologies from oil and gas into mining applications. Several modifications have to be pondered due to this technology exchange: smaller cuttings sizes because of using impregnated diamond bits; narrower annulus space; higher drilling fluid velocity and likelihood of turbulent flow regime in the annulus; and higher pressure loss. In particular the results of our lab experiments have shown that the increase in concentration of small size cuttings can significantly change the rheology of the mud when drilling in hard rocks. This, in return, could have a noticeable increase in the pressure loss encountered along the annulus space. As a continuation of the above study, numerical simulations were conducted to investigate the cuttings transport behaviour in small size annulus space. Fluid velocity, annulus size, cuttings concentration, cuttings density, and cuttings size were some of the parameters that were varied to see their effects on cuttings transportation and the pressure loss along the annulus space. The results indicate that, due to the differences between oil and gas and mining drilling, conventional oil well planning is not applicable for mineral exploration drilling and numerical simulation would help in this matter.

Aug 1, 2013

By J Poniewierski, Varcos D

Efficient blasting requires constant vigilance with respect to the actual layout being used in the field. Objective measurement techniques are required in laying out a pattern as the 'by eye' or 'thumb suck' methods cannot guarantee consistent results in layout. Erratic blast results are the consequence of such an approach. In a case study at Sons of Gwalia mine, it was demonstrated that incorrect front burdens had a snowballing effect on otherwise carefully laid out blasts, resulting in both excessive amounts of boulders caused by preconditioning of bench fronts and tops, and tight digging. Both problems caused lower excavator productivity and excessive excavator damage, as well as making it difficult to set out subsequent blasts correctly. Several field measurement methods are available to aid in determining correct blast layouts and one is described in this paper.

Jan 1, 1994

By Georges Croisé, Les-Lee Thompson, Adrien Debergé

Membrane filtration systems have regained focus in recent years as an effective means of liquid-liquid separation to increase the concentration of valuable elements, recover reagents or remove impurities. ORANO Mining (formerly AREVA) investigated this cost optimization process opportunity as early as 2011 for implementation at the Trekkopje project (Namibia). The key focus was to separate and recycle bicarbonate from the uranium bearing eluate solution. The performance targets were successfully achieved at lab- and pilot scale with an ultrafiltration and nano-filtration configuration system. Early 2015, ORANO Mining further launched an investigation into the use of membranes for acid recycling at the KATCO In Situ recovery mine in Kazakhstan based on the favorable results from the original bicarbonate application. KATCO is the world leader in ISR uranium mining with an eluate processing capacity of 80 000 m3/yr. This site consists of two processing plants namely, Muyumkum and Tortkuduk, located 40 kilometers apart, both operating under acidic conditions whereas precipitation and packaging are based in Tortkuduk only. This paper serves to present the results from the integration of a nano-filtration system at the Muyumkum satellite processing plant. The project consisted of screening laboratory bench studies conducted at ORANO-CIME followed by process validation at KATCO through further bench and pilot test work. The feasibility study assessments were successfully concluded which led to the implementation at an industrial scale in Muyumkum of a nano-filtration process to reduce eluate volumes being sent to the uranium precipitation section whilst achieving effective separation of uranium from sulfuric acid. Nano-filtration technology has drawn significant attention due to the efficiency and reproducibility of the process and its moderate capital cost relative to operational savings. The reliability of the previous results is a great opportunity to reduce operative expenditures within ORANO’s next ISR mining project in Mongolia.

Jan 1, 2020

By J. R. Patts, J. P. Rider, J. A. Organiscak, A. B. Cecala

"NIOSH recently completed a 15-month study at an underground limestone mine crusher booth which evaluated three research parameters: (1) the effectiveness of a single-filter filtration and pressurization system for improving the air quality inside the operator booth, (2) comparing the effectiveness of ? > 99 and ? > 95 experimental prototype filters in the system, and (3) evaluating the use of three different pressure monitoring devices to determine the performance of the filtration and pressurization system over time. The protection factor was quantified monthly using particle counters in the respirable dust range (0.3–10 µm), and gravimetric dust samples were gathered at the beginning and end of the overall study. Under static conditions and after outlier removal, the single-filter filtration unit installed offered a protection factor between 8 and 216, depending on the filter type and loading condition. The particle counting analysis shows that the ? > 95 filter offers a protection factor greater than 4-times that of the ? > 99 filter when evaluated over 60 minutes. The booth pressure monitors provided data that proved to be a valid indicator of system performance over time. INTRODUCTION Designed and installed correctly, enclosed cabs, operator booths and control rooms offer mine workers protection from physical hazards, such as flying rock, debris, and noise, as well as a more comfortable environment in regards to temperature and humidity [1]. But while it may be easier to quantify whether the A/C unit is working (measuring the temperature) or observe whether the cab offers protection from flying debris, it can be somewhat more difficult to quantify its performance in reducing respirable dust hazards. For over 15 years, NIOSH has been conducting applied research to improve the air quality inside of enclosed cabs of mobile equipment [2-5]. This work has led to the identification and mathematical modeling of enclosed cab filtration systems [6]. The same principles that govern the performance of filtration systems on mobile equipment are applicable to stationary enclosures such as operator booths and control rooms [1, 7]. Stationary enclosures are similar to enclosed cabs; however, the volume of the work area can be significantly larger. In addition, workers who perform their duties in stationary enclosures tend to stay within the room for a greater percentage of the day, as opposed to workers on mobile equipment who may enter and exit frequently. Structural integrity can be easier to maintain as well, as there is typically less vibration and stress placed on these compartments as compared to mobile equipment. In addition to offering protection from dust and flying debris, enclosures must ensure that workers have a healthy supply of fresh air to avoid elevated levels of CO2, which are known to cause headache and dizziness, impairing cognitive function. The American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE) states that enclosures should have no more than 1,100 ppm of CO2 when outside levels are 400 ppm [8]. In addition, the American Society of Agricultural and Biological Engineering (ASABE) recommends a minimum airflow for enclosed cabs of at least 42.5 m3/hr (25.0 cfm) per person [9] to ensure an acceptable level of CO2."

Jan 1, 2017

By Andre L. De Vegt

Hydrogen sulfide is an expensive chemical used in nickel, zinc and copper mining and metallurgical operations for selective recovery and concentration of metals, from leach water streams, acid plant blow down streams, refinery electrolyte bleeds and precious metal, plant bleeds. Hydrogen sulfide is either produced on site by catalytic reduction of elemental sulfur or transported to the site as liquefied hydrogen sulfide (H2S) or as a sodium sulfide solution (NaHS) Biologically produced hydrogen sulfide has economically very interesting, application possibilities in the mining and metallurgical industry. Converting sulfates from waste streams into usable hydrogen sulfide by biological reduction results in operational cost savings in existing lime treatment systems. H2S can be produced biologically for less-than $500/ton S. For the past ten years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove sulfate and heavy metals. The hydrogen sulfide produced is used for recovery of metals,, mainly zinc, from the ground water stream. The system has been operating since May 1992 treating a flow of 5000 m3/d. At Kennecott's Bingham Canyon Utah copper mine, a pilot plant started operation in November 1995 to develop the process for selective recovery of copper from leach water using biologically produced hydrogen sulfide from sulfate containing groundwater. Other pilot plants are operated at DOE's Pittsburgh Research Center and at Cominco Research focusing on selective recovery of metals.

Jan 1, 1998

By Andrew Trusiak

Brunswick Mining, employing approximately 1600 employees, is located 40 km south of the city of Bathurst in north eastern New Brunswick. The mine has operated as two lead-zinc operations - the underground mine(No.12) and the open pit mine (No.6). The open pit orebody is presently being' mined by underground methods. It is expected that the No.12 mine will furnish the entire ore supply by the end of 1981. The flotation practice prior to 1971 has been described by Neumann and Schnarr(1) and by Erskine (2). More recently, the current flotation practice has been described by McTavish(3) and deals with some major circuit modifications between 1972 and 1978. The period 1978 to 1980 has seen the completion of. a major flotation cell replacement and expansion program for the No.6 concentrator, and the implementation of computer control in the No. 12 CuPb and Zn flotation circuits.

Jan 1, 1981

By L. B. Phelps

Current mining regulations require revegetation in reclaiming surface nines. Excessive soil compaction can be an impediment to successful revegetation in poor soil conditions common to Eastern coal nine sites. A field study was performed to determine the bulk densities of soils that had been spread by either bulldozers or scrapers at a strip nine site. Moisture-density relationships for the soils were determined from the field samples. These were compared with stockpile samples compacted by the Standard Proctor compaction test. The results of the study indicate that the degree of compaction could be lessened through proper soil handling procedures.

Jan 1, 1986

By Wilbur I. Duvall, Thomas C. Atchison, Joseph M. Pugliese

Short cylindrical charges were detonated in drill holes in rock to determine the effect that decoupling ( defined as the ratio of the radius of the hole to the radius of the charge ) has on the strain - generating abilities of explosions in rock . The amplitude and period of the strain pulses produced in the rock were studied as a function of distance , size of charge , and decoupling . The main results of these studies were that , for a given distance and size of charge , the amplitude of the strain pulse decreases as decoupling increases and the period of the strain pulse decreases at first and then increases as decoupling increases . A simplified theory of decoupling is presented that satisfactorily explains the experimental results . The information presented makes it possible to predict the effect of decoupling on explosiongenerated strain pulses in rock and thus helps the explosives user evaluate the effect of decoupling on his blasting .

Jan 1, 1964

By C. W. Whitten

Solis from an abandoned Pb battery processing facility were characterized prior to the selection of the extraction technique. Reflected light microscopy and electron beam methods were used to locate Pb-bearing phases and to quantify the compositions of the phases. It was found that the soils are composed primarily of quartz and feldspars with minor amounts of iron and titanium oxides. Lead is primarily present as an oxide or sulfate that is associated with the silicate minerals. Specific phases identified were PbO; Pb02; cerrusite, PbCO3; angleslte, PbSO4; galena, PbS; and magnetoplumbite, 2PbO3Fe2O3; or plumboferrite PbO2Fe2O3?

Jan 1, 1989

By J. Menuge, G. Barker

"Liberation (QEM-SCAN) and surface chemical (time of flight secondary ion mass spectrometry -ToF-SIMS) analyses have been undertaken on plant Pb circuit flotation samples with the aim of defining the factors resulting in sub-optimal recovery. Lead flotation circuit feed, cleaner concentrate and tails samples were examined on a size-by-size basis using QEM-SCAN. Sulfide minerals accounted for approximately one third of the flotation feed with pyrite making up 16 wt.%, followed by sphalerite (13 wt.%) and galena (3 wt.%). Non-sulfide gangue minerals comprised calcium carbonates calcite (26 wt.%), dolomite (14 wt.%) with quartz, feldspars and barite all contributing > 5 wt.%. QEM-SCAN analysis indicated that liberation was not the primary cause of the poor flotation response. Principal component analysis was applied to the ToF-SIMS data derived from five samples (as for QEM-SCAN plus rougher concentrate and tails) to enable identification of correlated surface chemical components. Although a significant range of correlations were observed we focus here on those that show a discernible pattern throughout the float circuit. It was found that for the flotation feed the surface of galena were largely obscured but where Pb was observed there was a strong correlation to surface Fe. For the rougher and cleaner concentrates the galena surfaces were relatively clean with no correlation to Fe for the rougher concentrate and minor correlation in the cleaner concentrate. However, in the rougher and cleaner tails the clear correlation of galena with Fe was again apparent. These results suggest, in combination with prior studies of pyrite morphology, that the principal factor effecting grade is the rapid oxidation of the framboidal pyrite resulting in the contamination of the galena surface with a high loading of hydrophilic oxidised Fe species, thus depressing flotation."

Jan 1, 2014

By C. Clark, R. Pakalnis, B. Seymour, L. Martin, R. Jacksha, M. Stepan, M. Roworth, C. Caceres

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop safe practices for the use of shotcrete as ground support in underground mines, particularly mines operating in weak host rock. As part of this research, a rugged, portable direct tensile test system was developed for measuring shotcrete adhesion strength in underground mines. During the development of this test system, more than 185 direct tensile tests were conducted with a common, commercially available macro-synthetic fiber-reinforced shotcrete that was applied to concrete test panels using a dry mix process and machinery. The average bond strength of the shotcrete to the concrete substrate typically increased as a function of the shotcrete’s curing age, ranging from 0.44 MPa (64 psi) after one day of curing to 1.58 MPa (229 psi) after 90 days of curing. Adhesion strength increased markedly between one and three days of curing, reflecting a similar trend of increasing shotcrete tensile strength with curing time. This robust direct tensile test system can improve mine safety by providing a reliable means of measuring shotcrete adhesion strength and also supplying important information about the quality of the applied shotcrete and the competency of the underlying rock.

Jan 1, 2010

By H. Walqui

The Empire concentrator currently processes magnetite ore from the Empire pit which is approaching the end of its mine life. Over the past two years plant wide tests have been run to access the plant capability of processing ore from the neighboring sister Magnetite pit. The neighboring pit presents challenges to the Empire plant due to its higher feed grade, finer liberation size and higher percent silica which require additional secondary grinding and concentrating capacity to achieve concentrate grade. The following paper summarizes the results from the second full scale test, run during 2009 under a challenging market environment

Jan 1, 2010

By W. W. McClintock

A column flotation system was designed to conduct release analyses of a very finely disseminated, stratiform, copper ore from the Denali Copper Prospect, Alaska. Chalcopyrite is finely disseminated in a carbonate matrix and pyrite is disseminated in both the chalcopyrite and gangue, requiring grinding to 20 microns for adequate liberation. A 25 mm x 2.4 m glass flotation column was designed. The ore and its flotation tailings were repeatedly floated to obtain a rougher concentrate, which was repeatedly floated to produce release fractions. These were analyzed for copper, iron calcium and magnesium. Release curves were plotted. The procedure was replicated at each of two grinds; 99% and 88% passing 37 microns (400 mesh), and should find application for flotation characterization and process selection. Bond grindability work was also conducted.

Jan 1, 1994

By Marcel Bielefeld, Joost Bakker, Rob van Dorp

Pile load testing can be performed by a static, rapid or high strain dynamic (generally designated as dynamic) testing method. The static load test is often considered the “gold standard” of testing with the other methods merely ‘alternatives’. However, the rapid load test, as a quasi-static test, has all the positive elements of the static alternative: the direct measurement of loads and displacements. Moreover as stress wave phenomena have no influence, the interpretation of rapid load test results is more straightforward than that of dynamic testing, and also independent of the person performing the interpretation. This paper will explore the Rapid Load Testing method and illustrate the advantages and limitations through a case study in Rostock, Germany

May 1, 2022

By N. S. Dalal, X. Shi, V. Vallyathan

"Electron spin resonance (ESR) and cytotoxicity measurements were made on newly fractured silica to examine specifically the role of the fractured-induced, siliconbased radicals (Si· and SiO·), and silica-generated hydroxyl (·OH) radicals in the mechanism of the cell membrane damage by silica. The concentration of the Si· and SiO· radicals was controlled through decay processes, thermal annealing, and boiling, while that of the ·OH radicals was varied by using catalase, superoxide dismutase, KMnO4, Ha2seO3, ascorbic acid, and metal ions, and monitored via ESR spectroscopy. The dust's cytotozicity potential was evaluated by measuring the silica-induced hemolysis and also by determining lipid peroxidation (using linoleic acid). Prom the comparison of hemolysis and ESR results it is deduced that the radicals play little· or no role in the silica-induced hemolysis. However, the lipid peroxidation data indicate that the radicals might be involved in the initiation of an oxidative chain reaction leading to the macrophage membrane damage through lipid peroxidation. INTRODUCTIONThe biochemical mechanism of Quartz-related pneumoconiosis is still not fully understood. It is believed, nevertheless, that one event of primary importance is the perturbation of cell membranes by the dust particles (Allison et al., 1966; Allison and Harrow, 1971; Bateman et al., 1982; Parazzi, et al., 1968; Reiser and Last, 1979; Shi et al., 1989; Summerton et al., 1977). The ensuing cell-membrane damage unleashes certain lytic enzymes resulting in additional cell injury and eventual fibrosis (Nolan et al., 1981; Summerton et al., 1977). Thus considerable effort is currently being made towards the understanding of the processes by which quartz particles disrupt the membrane of a red blood cell (RBC) or a pulmonary alveolar macrophage (PAM). A simple but important method of evaluating the membrane damage potential of a dust is the hemolysis test (Harington et al., 1971). Even though this test is used routinely for screening dusts for their cytotoxicity potential, the biochemical mechanism underlying the cell lysis by many dusts, including quartz, is still controversial (Kilroe-Smith, 1974; Singh and Rahman, 1987), and this provided us the impetus for the present undertaking."

Jan 1, 1989

By John M. Kelly

New Mexico produced 31,913,816 bbl. of oil in 1942, the lowest annual production since 1936, and dropped one place to rank eighth among oil-producing states. This production decreased 7,838,052 bbl., or 19.71 per cent, from the 1941 figure is the result of transportation difficulties caused by the dislocation of tanker sailings to east coast ports. The average per-well allowable in New Mexico on Jan. I, 1942, was 43 bbl. and at the end of the year was 38 bbl. Allocations as set by the New Mexico Oil Conservation Commission followed the recommendations of the Petroleum Administrator for War. After setting the daily outlet, however, the average daily pipe-line runs were 87,545 bbl.—11.06 per cent short of these allocations. Production for Lea County was 26,812,949 bbl., Eddy County 4,624,578 bbl., northwestern New Mexico 473,609 bbl., Chaves County 2,680 barrels. Drilling activity for New Mexico in 1942 was approximately 84 per cent of that in 1941 with 339 completions. Of these completions 254 were oil wells, II gas wells, and 74 dry holes. Proven fields accounted for 55 of the dry holes and 19 were wildcats. Three new oil fields and one new gas field were discovered as the result of wildcat drilling. Extensions were made to one oil field and one gas field. By the close of the year, the New Mexico Oil Conservation Commission had designated 59 areas as proven for oil and/or gas. Southeastern New Mexico Lea County Monument was again the largest producing field in the state, with 5,729,336 bbl.; Eunice was next, with 5,217,965; Vacuum produced 3,295,624 and Hobbs 2,973,488. The Hobbs field has the largest accumulated production, which at the close of 1942 totaled 100,381,417 bbl. The 100-million-barrel mark for Hobbs focused attention on the fact that this is the first field in the state to attain this figure, and also that, as Hobbs has been under continuous proration since July 1930, or approximately the entire life of the field, this 100-million-barrel recovery was obtained with 86 per cent of the wells in the pool still flowing and having a drop in bottom-hole pressure of only 3.5 Ib. per million barrels recovered. Hobbs stands out as perhaps the best regulated major oil field in the world. Two new oil fields were discovered in Lca County, the most inlportant being the area designated as East Lusk, consisting of the south 4 tiers of Sections in T. 19 S., R. 32 E. The discovery well was drilled in the SW. SW. 1/4 of sec. 21, T. 19 S., R. 32 E., by Culbertson and Irwin, Inc., and others. It was completed at a total depth of 2751 ft. in the Seven Rivers formation of Permian age. The initial potential of the well was 237 bbl. per day on pump. The oil produced has a gravity of 24.10 A.P.I., with sulphur content of 0.9 per cent. This oil has an asphaltic base and because

Jan 1, 1943

By John M. Kelly

New Mexico produced 31,913,816 bbl. of oil in 1942, the lowest annual production since 1936, and dropped one place to rank eighth among oil-producing states. This production decreased 7,838,052 bbl., or 19.71 per cent, from the 1941 figure is the result of transportation difficulties caused by the dislocation of tanker sailings to east coast ports. The average per-well allowable in New Mexico on Jan. I, 1942, was 43 bbl. and at the end of the year was 38 bbl. Allocations as set by the New Mexico Oil Conservation Commission followed the recommendations of the Petroleum Administrator for War. After setting the daily outlet, however, the average daily pipe-line runs were 87,545 bbl.—11.06 per cent short of these allocations. Production for Lea County was 26,812,949 bbl., Eddy County 4,624,578 bbl., northwestern New Mexico 473,609 bbl., Chaves County 2,680 barrels. Drilling activity for New Mexico in 1942 was approximately 84 per cent of that in 1941 with 339 completions. Of these completions 254 were oil wells, II gas wells, and 74 dry holes. Proven fields accounted for 55 of the dry holes and 19 were wildcats. Three new oil fields and one new gas field were discovered as the result of wildcat drilling. Extensions were made to one oil field and one gas field. By the close of the year, the New Mexico Oil Conservation Commission had designated 59 areas as proven for oil and/or gas. Southeastern New Mexico Lea County Monument was again the largest producing field in the state, with 5,729,336 bbl.; Eunice was next, with 5,217,965; Vacuum produced 3,295,624 and Hobbs 2,973,488. The Hobbs field has the largest accumulated production, which at the close of 1942 totaled 100,381,417 bbl. The 100-million-barrel mark for Hobbs focused attention on the fact that this is the first field in the state to attain this figure, and also that, as Hobbs has been under continuous proration since July 1930, or approximately the entire life of the field, this 100-million-barrel recovery was obtained with 86 per cent of the wells in the pool still flowing and having a drop in bottom-hole pressure of only 3.5 Ib. per million barrels recovered. Hobbs stands out as perhaps the best regulated major oil field in the world. Two new oil fields were discovered in Lca County, the most inlportant being the area designated as East Lusk, consisting of the south 4 tiers of Sections in T. 19 S., R. 32 E. The discovery well was drilled in the SW. SW. 1/4 of sec. 21, T. 19 S., R. 32 E., by Culbertson and Irwin, Inc., and others. It was completed at a total depth of 2751 ft. in the Seven Rivers formation of Permian age. The initial potential of the well was 237 bbl. per day on pump. The oil produced has a gravity of 24.10 A.P.I., with sulphur content of 0.9 per cent. This oil has an asphaltic base and because

Jan 1, 1943

By R. W. Thompkins

MINE operators are concerned with temperature conditions in their mines, particularly the effects of high temperatures on the l1ealth and efficiency of tl1eir employees. This paper is written to focus attention on the variables of heat transfer between rock and air. It illustrates the difficulties of predicting the manner, and the extent, of heat transfer from theoretical concepts, prior to actual operation of a mine airway. There are ~1any sources of heat in mines. The most important is that of the rock surrounding the airway. This heat, in turn, is a product of the age of the rock, faulting, proximity to recent igneous activity, oxidation of sulphides, hot ground waters, etc. The sources of heat may be constant for any one mine, but they are far from constant when dealing with various mining districts or e1•en with a number of mines in the same district. A second source of heat is that produced by machinery in operation. Practically all the waste

Jan 1, 1962

By Mohammad Kor, David Beattie, Agnieszka Mierczynksa-Vasilev

The selectivity of polymer adsorption in mixed mineral systems is the basis for polymer depression of gangue minerals in flotation. Effective polymer depressants not only reduce gangue mineral recovery, they also have minimal effect on the recovery of the value phase, presumably through targeted adsorption on the gangue phase, and minimal uptake on the value phase. Traditionally, polymer depressant design has been guided by single mineral phase adsorption tests, with affinity and maximum adsorbed amount determined for gangue and value phases separately. However, there is a need to determine the actual extent of adsorption on the gangue phase while in the presence of the value phase. In this work, we report on the development of in situ atomic force microscopy (AFM) imaging for determination of polymer depressant coverage and morphology on mixed mineral surfaces. Our group has previously used AFM imaging on single minerals to connect adsorbed layer characteristics with bubble-particle attachment and flotation outcomes. Two sample types were used to test the methodology: (i) a mixture of two crushed/ground minerals encased in resin; and (ii) a composite mineral sample containing macroscopic regions of three different mineral phases. The samples have been used to probe the selective uptake of two modified dextrin polymers (octenyl succinate anhydride dextrin). AFM images acquired in situ (while all surfaces are immersed in the same polymer solution) of each mineral phase have revealed the natural selectivity of the polymer for the mineral surfaces. In all cases, the polymers adsorb on the all mineral surfaces present, but to a varying extent.

Jan 1, 2014