Search Documents

By D. S. Dinsmoor

Boron, estimated to comprise about 0.001 percent of the earth's crust (Fleischer 10), as an element is never found free in nature, although its compounds are found in many localities. the borates are the most important. Sassolite (B(OH)3) and boracite (Mg6C12B1406), non-borates, are-of-minor importance. The crystal structures of most natural borates are still unknown. A classification based solely on the ratio of boron to the total number of cations has been devised (Palache 28). This classification divides the borates into four, sub-groups; anhydrous borates, hydrated borates, borates containing hydroxyl or halogen and compound borates. Only four or five minerals of the hydrated borates group have ever been used commercially. In more recent years, the sodium borates have comprised all but a 'small fraction of all borates used. Borax, the hydrated borate compound, is the most important of all boron compounds. It has been used so long and so often that the layman often confuses borax and boron and, applies the terms synonymously.

Jan 1, 1958

On 15 August 1998 the first section of the PUTRA LRT system was opened to the public as a free service prior to official commencement of revenue service on 1 September 1998. It is a remarkable achievement to open a highly advanced medium capacity urban railway scheme in four years after the outline concept began. Even more remarkable is the implementation of the next stage which is the underground section planned to be operational in mid-1999. The decision to build the first underground railway in any major urban centre is a technical challenge. The PUTRA LRT System can be likened to Hong Kong when the initial MTR system began in the 1970s and Singapore MRT in the 1980s. Prior to the PUTRA railway very little bored tunnelling had been undertaken in Kuala Lumpur. A few shallow sewer tunnels had been built but the main experience of tunnelling in Malaysia had been for water, hydroelectric and road tunnels usually through granite formations. The ground conditions in Kuala Lumpur were known mainly from experience of piled foundations and occasional deep excavations. The suitability and likely difficulties to be experienced during bored tunnelling could only be theoretically predicted. In both Hong Kong and Singapore, government owned corporations were set up to implement the scheme, but in Kuala Lumpur the whole project has been undertaken by a private company PUTRA, a wholly owned subsidiary of Renong Berhad.

Jan 1, 1999

By M Salu

Ventilation control devices (VCD’s) and bulkheads are critical controls used for managing risk in underground coalmines. Following the Moura No. 2 mine explosion in 1994, the Queensland Mines Department required that the design of VCDs be based on live testing (such as in a mine testing explosion gallery) and more recently on numerical modelling using measured seal material properties. While the stipulated methods represent an idealistic solution, they are not practical to implement as solutions to daily challenges presented in underground coalmines.Not all VCD’s and bulkheads are placed in areas which have been mined to standard roadway dimensions. Operationally, VCD’s may be required to be placed close to intersections or require large dimensionally different areas (eg overcasts and pre-driven recovery road shutters) compared to the live testing or numerical modelling originally undertaken.This paper describes the various structural engineering methods utilised to account for the design of VCD’s where the operational requirements are non-standard. Siting and construction of VCD’s near the entry of cut throughs and geological structures requires additional design considerations. While VCDs constructed from a single material (eg sprayed mining plaster) are relatively straightforward to design, the addition of multiple openings (doors) or large pipes will complicate the structuralanalysis significantly.Temporary bulkheads used for the containment of grout such as for the construction of pre-driven recovery roads in coal mining have a significantly different risk profile to VCDs and should be designed accordingly. Recent failures and near-misses in such bulkheads have highlighted this issuefor the authors.The existence of an Australian Standard for Underground Mine VCDs and Bulkheads would go a long way to addressing many of the issues raised in this paper. Without a single, industry-accepted reference for VCD design, individual mines will have to continueto exercise their best judgements using whatever local expertise is available to them.

Oct 12, 2022

By P. Kim Carroll, D. Nick Tiffany, Doyl M. Fritz

Thunder Basin Coal Company received the 1987 Wyoming Excellence in Surface Mining Award for construction of the State's first major sediment control reservoir to be designed using the new settleable sol ids standard. Use of this standard resulted in construction cost savings of more than $250,000; reduced water quality monitoring; enhanced downstream channel stability because of more natural sediment loading; allowed simultaneous establishment of permanent waterfowl and fisheries habitat; and provided a quality recreational site. This article will address factors associated with the design and construction of that sediment reservoir and the benefits that were realized. (Note: This paper was originally published in the proceedings for the 1988 National Symposium on Mining, Hydro1ogy, Sedimentology and Reclamation held in Reno, Nevada, December 5-9, 1988.)

Jan 1, 1989

By Jalna R. Zatko

Coal-clay waste slurries were dewatered in laboratory-and small-scale continuous tests by the Bureau of Mines using polyethylene oxide (PEO) as a flocculant. Dewatering from a nominal 7-wt-pct solids to over 50-wt-pct solids was accomplished using 0.5 lb of PEO per ton of feed in small-scale continuous tests. Parameters such as pH, initial solids content, and PEO concentrations were investigated. Water recovered from dewatering was reused as dilutant for PEO solutions.

Jan 1, 1982

By Joseph Sopko, Xavier Lacourse-Dontigny

For the REM (Réseau Express Métropolitain) project, a 2500 m tunnel was built using a tunnel boring machine (TBM) under the Montreal Pierre Elliott Trudeau Airport (ADM). Although the geology under the Montreal Airport (ADM) would have been suitable for an excavation with a hard rock machine, the rst section reuired an earth pressure balance (EPB) TBM due to the soft soil located under wetlands. After excavating 280 m, the TBM was blocked in a transition zone of unconsolidated, water-bearing soils directly above the underlying bedrock. A free air intervention was not possible due to these geological conditions. After several failed attempts to create a slurry cake for hyperbaric interventions, a ground freezing system was designed and implemented, incorporating angled pipes drilled from outside the wetlands to directly in front of the cutterhead. This paper discusses the engineering reuired to form a frozen, water-tight zone in front of the cutterhead using liuid nitrogen. It also describes the complex method of replacing the disc cutters while holding the ground freezing system active in a manner protecting the health and safety of the workers.

Jun 23, 2024

By WILLIAM COUPER

THE completion of the excavation of the tunnels through Bergen Hill for the extension of the Pennsylvania Railroad into New York City, together with the fact that the excavation for the rest of the tunnel-line has been practically completed for some time past, arouses sufficient interest to justify a description of the engineering- and contracting-work, and the organization by which it has been accomplished. The finishing of the excavation is a long step towards the completion of the entire tunnel-project. It will be interesting to the members of the Institute, who last spring were taken through a great part of this work, to know that by the excavation now completed it is possible to walk by tunnel from a, point near Sunnyside yard, Long Island, east of the 34th Street ferry, to the central passenger station site in the City of New York, and thence by tunnel to the Hackensack meadows, and by an embankment constructed across these meadows to Newark, N. J. This New York tunnel extension is being constructed as a part of the Pennsylvania Railroad system by the Pennsylvania Tunnel & Terminal R. R. Co., a corporation of the States of New Jersey and New York. It extends from a point near Newark, N. J., to the Sunnyside yard, Long Island, as indicated on the accompanying plan.

Jan 7, 1908

By H. C. Fowler, G. B. Shea

MODERN industry's incessant demands for increased operating efficiency and lower costs require that hazards attending all occupations be reduced to a minimum. Reduction of the inevitable losses that result from accidents and injury to the worker is one of the important economic problems confronting industry today and is the basis for the widespread safety movement. Dr. Charles E. Munroe, chief explosive chemist of the U. S. Bureau of Mines, is father of the statement, "The existence of a nuisance is evidence of an economic waste." This pointed expression of the internationally recognized scholar and explosives engineer has a direct relation to the prevention of accidents. Every injury and death in industry is a waste in human endeavor and a lessening of productive gain. Dr. Munroe has aptly paraphrased his previous summation with reference to wastes as follows: "A lost-time accident is evidence of an economic waste." That the economic waste entailed by occupational accidents is chargeable to industry is well substantiated by the fact that all but four states (Mississippi, South Carolina, Florida and Arkansas) now have workingmen's liability and compensation laws.

Jan 1, 1933

By Seung-Kyu Son, Michael T. Chandler, Youngtak Ko, Gyuha Hwang

Over the past decade, sea-floor hydrothermal vent fields have been studied by many researchers because of their commercial potential of mineral resources and the origins of Earth’s life. Approximately 300 of these are reported as massive sulfide deposits near the mid-ocean ridge, most of which are located in the Atlantic and Pacific ridges. However, only fourteen deposits have been identified in the Indian mid-ocean ridges. The Central Indian Ridge (CIR) between 8°S and 12°S is composed of three segments with a slow full- spreading rate of 33-37 mm/yr. The hydrothermal activity at the slow-spreading center can be generated along the ridge axis attended by volcanism or along the tectonic features, such as oceanic core complexes (OCCs). OCC is an exposed mantle rocks composed of peridotite and ultramafic rocks uplifted through long-lived detachment fault processes which can also lead to extensive hydrothermal circulation near the slow-spreading center. Therefore, the identification of OCC’s properties will be an important indicator for finding the sea-floor hydrothermal vents. To study hydrothermal activity of the CIR, Korea Institute of Ocean Science and Technology (KIOST) have conducted expeditions using R/V Onnuri over four years (2009-2011, 2017). High-resolution bathymetry and backscatter data was obtained during expeditions using multibeam echo system of EM120 in 2009-2011 and deep-tow side-scan sonar system of IMI-30, which has more higher resolution than EM120, in 2017. In this study, we use these high-quality data for constraining location and size of OCC. We also analyze the geophysical and morphotectonic characteristics of OCC gathering high-resolution bathymetric map and backscatter image.

Jan 1, 2018

By Garland Likins, Gray Mullins, George Piscsalko

"Quality control of drilled shafts is greatly dependent upon the practices of the site personnel. For drilled shafts cast under slurry, inspection of the hole prior to concreting is very difficult or impossible. There are numerous non-destructive test (NDT) methods currently available to assess the integrity of drilled shafts. This paper will discuss the theory and use of an emerging NDT technology known as Thermal Integrity Profiling (TIP). The Thermal Integrity Profiling method measures the elevated concrete temperatures that occur during the hydration process. These temperature measurements are made along the length of the pile and can determine the integrity over 100% of the pile cross section, both inside and outside the reinforcing cage. With the known shaft volume information, TIP can evaluate the effective shaft radius at each measurement location. With the increased use of TIP on highway projects, there is a need to have standard criteria for shaft acceptance. Shaft acceptance criteria can be based upon thermal measurements and subsequent analysis of the data to determine the average shaft radius, local concrete cover, and cage alignment. With this additional information obtained via the thermal testing method, acceptance methods based upon concrete cover can be developed. In this paper the Thermal Integrity Profiling method will be described, results from a case history will be discussed, and an acceptance criteria based upon concrete cover will be proposed.INTRODUCTIONDrilled shafts are an attractive foundation element in many applications due to their large axial and lateral capacities. When drilled shafts are cast in a dry hole, it is possible to inspect the hole prior to casting, allowing for very basic level of quality control, although the shape of the completed element is still unknown without some form of post construction testing. When drilled shafts are installed where soil conditions are unstable, the shafts will often be cast under slurry to support the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to impossible to accurately and efficiently inspect the hole prior to casting concrete and it is equally difficult or impossible to inspect the shaft during the casting process"

Jan 1, 2016

By Marc. A. Meyers

The analysis of the phenomena involved in the determination of the compressive strength of iron-ore agglomerates leads to the identification of the important parameters. It is shown mathematically that the pellet rupture strength is proportional to the cross-sectional area. Fracture is initiated at the center of the pellets by the tensile stresses developed by the compressive loads normally to the compression axis. The variation in strength between individual pellets of identical composition and subjected to identical treatments is due to internal voids of varying sizes, that act as stress-concentration sites. Two novel testing procedures are proposed. The first consists of testing the pellets between two plates having three steel spheres each. This configuration simulates much better the environment actually encountered by the pellets. The second procedure consists of a thick-walled cylinder in which a piston penetrates; a large group of pellets is tested simultaneously, as the stress versus strain plot is being recorded. This latter test presents significant advantages over the conventional testing procedure; the main one is that one single test is sufficient to characterize the mechanical response of the pellets.

Jan 1, 1981

By Michael J. Friedel

As part of an investigation aimed at improving the health and safety and competitiveness of the mining industry, the U.S. Bureau of Mines evaluated the application of common offset radar profiling, using a 250-MHz ground-penetrating radar (GPR) system, for the detection of fractures in igneous rock. A series of radar reflection surveys were conducted to detect and delineate the extent of fracturing at various granodiorite and gabbro quarries and outcrops located in Minnesota. The application of radar profiling for detecting joints, sheeting fractures, shear zones, and depth to water table was demonstrated to be feasible with minimal processing. Radar reflection interpretations were verified by visual inspection of the rock mass and field mapping of local structure. The radar reflection section provides a simple, rapid, and cost-effective means for mapping of shallow (less than 10 m) small-scale fractures (greater than 0.25 cm) in igneous rock masses (characteristic of velocities between 0.061 m/ns for gabbro and 0.125 m/ns for granodiorite). Depth or distance estimates to fractures are within 10 pct of the actual, and time-shift compensation is necessary only when topographic irregularities exceed 30 cm.

Jan 1, 2010

I wish that in addition to being a Pro- fessional Engineer I was also a communications expert. My principal task this morning, and yours after this meeting, is to convince a wide variety of individuals that steel industry slags are a high quality material that can be used for many purposes; and that their use can significantly alleviate some of the problems facing engineers, public officials, and the general public in our countries. By actual in- place performance over a long period of time steel industry blast furnace slags have proven that they are as good as the best natural aggregates, and better than some, for any type of construction or purpose for which natural aggregates are used. Steel furnace slags have many unique favorable characteristics and prop- erties when compared to other types of aggre- gate even though they cannot be used for all types of construction. We have the facts, all we have to do is present them to the right people in the proper manner.

Jan 1, 1979

By A G McLean

This paper will first discuss the fundamental requirements for reliable discharge of backfill by gravity alone at high per cent solids. This discussion will include brief mention of the underlying principles of saturated solids flow contrasted to that of stirred tank or dilute discharge systems. Here the need to possess full knowledge of the flow properties of the stored material will be highlighted. In regard to attainment of reliable discharge it will he revealed flow from a backfill silo will only occur provided: ò the flowing material in the converging channel is yielding throughout; ò slip is occurring along the walls; ò an arched stress field is present in the vicinity of the outlet; ò the flowing backfill must be dilating to flow in response to the dilating stress field; ò sufficient dilation water is injected, in the hopper, to eliminate the formation of adverse interstitial pressure gradients; ò sufficient dilution water is injected, downstream from the hopper outlet, to generate a pumpable slurry of maximum per cent solids; ò the silo level must be sufficient to prevent the pump suction forming a rathole; ò the system must be configured and operated to generate stable discharge density; and ò the system must be configured and operated to minimise damage to the pump liners. In addition proper account must be made of the silo overflow weir and settling capacity to match plant throughput. Here opportunity will be taken to highlight the complexity of this multi-phase flow situation as well as the general yet paramount requirements for reliable solids flow. It will be shown that by proper attention to the multi-phase considerations gravity discharge of slurries as a consolidated bed with minimal water content is possible. Such high solids discharge results in greatly reduced demand for process water. In addition pumping costs are reduced as is the delay time associated with the mine drainage operation. Confirmation of successful applications will be highlighted by reference to several recent case studies. In the concluding phase mention will be made of the key yet very simple and effective operation techniques which enhance reliable Discharge.

Jan 1, 1998

By Ben E. Lindsly

The study of "bottom-hole' samples follow,-is in natural sequence the study of samples3 obtained under high pressures at the well heads of flowing wells. The principal object of this phase of gas-solubility research, started actively in January, 1530, was to gain a more accurate knowledge of the physical and chemical characteristics of the oil-gas mixtures that exist in natural reservoirs. In possession of actual data regarding the condition of the oil; the quantity of gas liberated from solution upon dimunition of pressure; and the relative volumetric proportions of gas to oil at various pressures throughout the flow string in a well, it should be possible to predict, with a fair degree of accuracy, what physical changes these mixtures would undergo throughout the life of a pool. Such information not only is important in designing flow strings in flowing wells but is important also in solving problems relating to pumping efficiency and the power required for pumping. Although certain fundamental rata Mere obtained in the stud of samples taken at the well head, "bottom-hole" samples are more representative of subsurface mixtures of oil and gas because they are obtained at reservoir temperatures, and before the oil has had the opportunity of intermingling with extraneous gas; that is, gas which either was not in solution originally, or which was liberated from solution at some higher pressure, and later became mired with the original undissolved gas.

Jan 1, 1933

By Charles R. Boardman

Recent underground nuclear tests in tuff, alluvium, salt, and granite have yielded data essential to the evaluation of mining applications of contained nuclear detonations. The data indicate that for these media the cavity radius is predictable within ±20% without regard to the properties of the rock in the immediate shot environment. Properties of the chimney of broken rock resulting from collapse of the cavity, on the other hand, are found to be related to the properties of the rock and its preshot structural weaknesses. Seismic effects and radioactivity distribution are sufficiently documented to serve as a basis for predicting the safety conditions associated with detonations for a variety of yields.

Jan 1, 1964

By Edward O. Reinbold

The paper presents the results of a study which involved collection and analysis of airborne pollutant concentration data in two producing underground room and pillar metal mines which use diesel powered equipment in the area near the face. The results include the concentrations of CO2, CO, NO, NO2 and respirable particulate matter measured with the latest portable instruments, and the carbon and hydrogen contents of the particulate matter samples determined by combusting them in a Elemental Analyzer. The carbon and hydrogen contents are used to estimate the amount of diesel particulate matter in the mine ambient air. The short term grab sample concentration data, although not suitable for determining compliance with ACGIH Threshold Limit Values (TLVs), are related to the TLVs so that they may be compared conveniently. Lognormal frequency distributions and the arithmetic mean of the concentration measurement data are used to compare different mine situations. Conclusions are drawn as to which pollutants are most important to control under actual mine production conditions.

Jan 1, 1979

By Open-Hearth Steel

We have a very high-powered organization up here this morning, headed by Kenneth C. McCutcheon, general superintendent of the Ashland Division of the American Rolling Mill Company, and L. A. Lambing, superintendent of the open-hearth and Bessemer departments of Jones & Laughlin Steel .corporation of Aliquippa, Pa., representing the open-hearth men. Also, we have P. F. Dolan, assistant general manager of the Maryland plant of Bethlehem Steel Company, of Sparrows Point, and Harry E. McDonnell, superintendent of blast furnaces of Weirton Steel Company of Weirton, W. Va., representing the blast-furnace section.

Jan 1, 1940

By A J. Morrison, K Demir, J Kohmuench, K Runge, C Evans

The Eriez HydroFloat® is a flotation device capable of recovering significantly coarser and lessliberated particles than is possible using a conventional mechanical flotation cell. Originally developed for industrial and bulk mineral beneficiation, the HydroFloat® is attracting increasing interest as a means of increasing the required grind size for metalliferous ore flotation. Doing so would reduce the costs of processing complex ores, either by decreasing the energy required to grind the flotation feed or by increasing the throughput achievable with a given comminution circuit. Processing coarser particles would also result in coarser waste streams, potentially improving the mechanical and hydraulic performance of the waste dams that they are sent to. Recent work at pilot – and industrial-scale has proven the potential of the HydroFloat® technology to achieve these gains in metalliferous applications. However, in order to realise the full potential of the HydroFloat® technology, it is necessary to understand not just its performance but also the drivers for that performance. Doing so will allow the design and operation of HydroFloat® devices to be optimised for different ores and applications. For this work, a HydroFloat® pilot rig was deployed to a coppergold plant in Australia and was used to investigate the effect of stream and operating conditions for treating the tailings stream of one of the plant’s rougher flotation cells. Under each set of operating conditions, samples were taken of the HydroFloat® feed, tailings and concentrate streams, and processed to yield the grade and recovery achieved by the device. At the same time, the bubble size and bed behaviour inside the device were measured. This paper presents preliminary relationships observed between the operating conditions and the performance of the HydroFloat® cell, and thus suggests a range of possible drivers for the measured coarse particle flotation performance.

Aug 24, 2022

By G. A. Brady

Laboratory tests were conducted to determine the technical feasibility of separating anthracite particles from a water-anthracite slurry by atomizing the water and removing the resulting mist in an air current. Products containing 21 percent or less moisture were obtained from slurries made with minus 60-mesh anthracite. Typical recoveries ranged between 67 and 79 percent of the feed when the slurries were atomized in air currents with velocities below 70 ft/min.

Jan 1, 1967