Search Documents

By L. P. Weber

During the years 1983-1987, a research programme, jointly performed by the steel producers ARBED, British Steel Corporation, Peine-Salzgitter, Unimetal, and co-sponsored by the European Community for Steel and Coal (ECSC), has been carried out on steel H-piles of different shapes. The initial aim of the testing programme has been the improvement of bearing capacity, both in sandy and clayey soils. At two test sites, standard H-beams are compared to H-piles with different types of laggings or to H-piles grouted both under low and high pressure. In this paper and in view of the open european market in 1992, the H-pile capacities and their corresponding allowable loads, determined from codes, recommendations and computation procedures in use in Belgium/Luxembourg (B/L), France (F), Federal Republic of Germany (G), and the United Kingdom (UK) as well as their evaluation from dynamic CAPWAP and Case methods are compared to the static capacities measured in-situ. In addition, procedures for estimating the load/movement behaviour of H-piles from CPT, pressuremeter, and CAPWAP are compared to the measured curves.

Jan 1, 1991

By V. J. Sopuck, O. P. Lavin, Ian Nichol

"A major challenge of contemporary exploration geochemistry is the development of procedures that can locate blind mineralization or mineralization that sub-crops below a cover of transported overburden, the composition of which bears no relation to the underlying mineralization. Over the past few years, the possible existence of diagnostic geochemical features in the country rock associated with volcanogenic massive sulphide deposits has attracted increasing attention both on the local mine scale and on the regional scale. In the present investigation, the nature of the geochemistry of a number of Archean greenstone belts of the Canadian Shield is examined to determine the feasibility of distinguishing productive from non-productive areas of copper-zinc mineralization. The results indicate that productive areas are distinguishable from non-productive areas providing consideration is given to the effects of igneous differentiation on rock compositionIntroductionArchean massive sulphide deposits are an important source of copper and zinc, and to a lesser extent silver and gold, particularly in Canada. As in the case of most other forms of mineralization, there is a continual need to develop new techniques that will improve the chances of success in the search for these deposits. The majority of Archean areas in the northern latitudes are overlain by a variable cover of glacial overburden. Considerable progress has been made in the development of new geochemical exploration techniques for use in glaciated terrain, based on the detection of anomalous dispersion in the glacial overburden. In certain situations, however, as in the search for blind deposits or in areas covered by glaciolacustrine deposits, overburden geochemistry offers little hope for success. In the case of massive sulphide deposits, one possible solution may lie in the detection of anomalous geochemical signatures in the bedrock. Recognizing this possibility, attention has been directed to the investigation of the nature of lithogeochemical dispersion associated with massive sulphide deposits on both regional and local scales, to establish the potential of lithogeochemistry as an aid in the search for these deposits."

Jan 1, 1980

By K. Ramji

"The development curve in the extractive sector has become longer, steeper, and riskier due to increased social, legal, and political risks from various stakeholders. Indigenous peoples are a unique stakeholder because their growing legal rights to lands and resources can often determine a project’s outcome. A project will only be successful if it is able to obtain the legal permits, withstand any judicial reviews, and gain and maintain the social license to operate. Stakeholder identification, management, and engagement are key risk-mitigation tools required to successfully convert risks into opportunities.RÉSUMÉ La courbe de développement du secteur de l’extraction s’est allongée, elle est devenue plus abrupte et plus hasardeuse en raison de l’accroissement des risques sociaux, légaux et politiques venant des divers intervenants. Les peuples autochtones sont des intervenants uniques puisque leurs droits légaux croissants sur les terres et les ressources déterminent souvent ce qu’il adviendra d’un projet. Un projet ne pourra réussir que s’il est capable d’obtenir les permis légaux, passer à travers les analyses judiciaires, puis obtenir et maintenir le permis social d’exploitation. L’identification des intervenants, la direction et l’engagement constituent les outils clés de l’atténuation des risques nécessaires pour bien convertir les risques en possibilités."

Jan 1, 2016

There is an increasing demand for refrigeration as mines progress deeper. Mine refrigeration plants have special requirements in terms of their duty and application. There are no national or international standards applicable for the testing of these plants. There have been numerous examples of plants failing to meet their required nominal capacity, but with the plant owner being unable to enforce the design duty on the manufacturer, due to a failure to unambiguously specify testing or accepting criteria. This paper discusses some of the reasons for performance shortcomings and describes a methodology for developing and specifying performance criteria, when inviting design and/or construction tenders, and a method of performance and acceptance testing once the plant has been built and commissioned. These guidelines encompass the full range of performance duties expected from a mine plant, including stable operation at maximum and minimum plant capacity, and under the various combinations of extremes of high and low condensing and evaporating pressures. A description of a methodology for developing a computer-based mine refrigeration plant model is also presented as part of the performance testing criteria. The methodology is illustrated with reference to the actual performance and acceptance testing process used on the worldÆs largest bulk air cooler (R67) at the Enterprise mine at Mount Isa, Australia.

Jan 1, 2005

By Fernando Romero Lage

"Crushing and screening theory and application has remained fairly consistent in the last 50 years. The application of such equipment is guided by varied formulaic conventions and rules that due to the entropic nature of the process, remains more an art than a science. The variability of conditions creates an environment in which trial and error becomes the principal means of process balance and control. This paper illustrates some of the theories behind the process, plus other assumptions, postulates, myths and misconceptions that exist within the crushing and screening industry.INTRODUCTIONContinuous material balance calculations are habitually performed in the design of new comminution circuits as well as in the valuation of existing circuits. A continuous material balance calculation is one in which the input rate of material is equal to the output rate for each unit functioning in the circuit. At continuous analysis, there is no accumulation or losses of material within the system, as it is when performing a discrete event analysis.In order to produce viable and manageable mine-to-mill material, whether it is ready to leach or ready to mill, we must reduce the material in a series of stages. The power demand increases as the material size decreases, as it is when folding a piece of paper successively. As with the paper, there is a crushing size limitation that is a consequence of the mineral properties such as work index, moisture, viscoelasticity, etc. Comprehensive knowledge of crushing plants in both the aggregate and the mining industries show that, after three stages of crushing, a particle size distribution originating from a blasted deposit can be reduced from an nominal maximum size of 500 mm to a nominal maximum size of 12 mm. if the last stage of crushing is set in closed circuit, the screen openings will be able to yield a smaller top size.Achieving steady and continuous material balance poses major difficulties as crusher lose their settings, screens blind or peg, and material characteristics change geographically or seasonally. Overloading conditions in crushers and screens are nothing but counterproductive, and the net losses of an unbalanced circuit can be overlooked when mining operators are paying a lot more attention to the evermore complex systems downstream.It is not simply the crushing of the mineral but achieving the right size for the downstream milling process that will yield the maximum amount of energy savings."

Jan 1, 2010

By Osama Safaqah

The new Cooper River Bridge will replace two existing bridges along U.S. Highway 17. The cable-stayed bridge will be one of the largest in the U.S and will connect the City of Charleston and the town of Mount Pleasant, South Carolina. The 1,546-foot long main span over Cooper River is supported by two diamond-shaped towers and will allow for 1000-foot wide navigation channel. The Charleston high-level approach is approximately 4351-foot long and will provide 250-foot wide navigation channel over Town Creek, while the Mount Pleasant high-level approach is 2090-foot long. Due to the high seismicity in the region, potential vessel impact, and hurricanes, large lateral loads are expected. Among various types of foundations, 10-foot diameter drilled shafts were selected for their high capacity against lateral loading. The shafts are founded on a stiff to very stiff lightly cemented calcareous sandy clay or sandy silt layer, called Cooper Marl, which underlies coastal sediments of interbedded clays and sands. The main towers will be supported on a group of 11 shafts and protected from ship collision by a rock island. The High Level Approach piers will be supported on a pair of 2 shafts. The shaft tip elevation is up to 230 feet below water line. An elaborate geotechnical investigation has been conducted on the site including a load test program on full-scale shafts under axial and lateral loads. The results of the tests were used to calibrate the lateral and axial soil resistance. The objective of this paper is to present the different aspects of the bridge foundation design.

Jan 1, 2005

By J. A. Gutierrez-Rodriguez, R. J. Purcell, F. F. ApIan

"Based on contact-angle measurements and the work of adhesion equation, the hydrophobicity of a wide variety of coals was found to decrease with decreasing rank, fixed carbon and total carbon content and with increasing oxygen and hydroxyl content. The estimated hydrophobicity, based on the water-sessile-drop contact angle, is '\.. 20% for lignite, increases with increasing rank up to a maximum of 'V70% for low (LV) and medium (MV) volatile bituminous coals and then decreases somewhat for anthracite. Using the captive-bubble technique, the calculated hydrophobicity ranges from '\.. 0% (below HV A bituminous rank) to a maximum of 55% for L V-MV coal. The former estimation is believed to be the more accurate. While the water-sessile-drop contact angle as measured on a polished-coal surface is usually larger than that shown by the captive-bubble method, the two values were found to converge at""' 95% relative humidity. It is proposed that the surface of coal consists of three kinds of sites: strongly hydrophobic, weakly hydrophobic and hydrophilic. The sessile-drop technique measures the total hydrophobic sites whereas the captive-bubble method measures only the more strongly hydrophobic sites. A water film covers the weakly hydrophobic sites preventing their detection by the captive-bubble technique.INTRODUCTIONCoal is a mixture of the degradation products of plants and of mineral matter. The appearance and properties of a specific coal is determined by the nature of the original vegetation and the extent of the physical and chemical changes which have occurred after deposition. The coalification process may be considered to have started with peat formation followed by a transition to lignite due to burial under sediments and metamorphic processes. Further metamorphic transformation to bituminous coals and, finally, under intense metamorphic action, to anthracite causes the carbon content and rank of the coal to increase. With such a wide variation in their genesis and composition, equally wide variations in the degree of hydrophobicity of different coals may be expected. It is the purpose of this paper to provide a means of estimating the hydrophobicity of a given coal sample based on rank parameters."

Jan 1, 1989

This report presents the results of reconnaissance-level investigations of the mill refuse disposal systems for 15 plants throw-heat the conterminous United States. The sites visited represent a cress section f the copper, iron, lead and zinc, and phosphate industries' practices in the field of fine-grained refuse disposal. The reconnaissance-level investigations were carried out to gather supplemental data to tae in-depth studies of Kennecott's Magma and Phelps Dodge's Morenci tailings deposits and Kennecott's Chino leaching dump. The various sites visited were classified according to the different systems and techniques used by the mining industry. The probable effects and relationships between site conditions and disposal methods were determined and evaluated to the extent feasible by a reconnaissance level investigation.

Jan 1, 1974

By Robert A. McColly

This Bureau of Mines report compares the availability of federally owned minerals in Arizona with lands considered favorable for discovery of mineral resources, to deter-mine the extent to which Federal mineral lands in such areas have been withdrawn by legal action or restricted by management practice. Of particular concern are restraints on Federal lands in areas identified as highly favorable for occurrences of valuable mineral deposits. Excluding Indian lands held in trust by the Federal Government, about 32 million acres, 44%, of Arizona's mineral estate is federally owned. This total includes lands with partial Federal mineral ownership. Approximately 16.5 million acres, or 52% of these lands, are available for location or lease. This includes 496,000 acres, 62%, of the lands highly favorable, and 2.6 million acres, 57%, of the lands moderately favorable for locatable minerals in Arizona. All other Federal mineral lands are either withdrawn or restricted, reflecting a wide range of purpose, authority, and impacts on mineral exploration and development.

Jan 1, 1987

By B. Arjang

ABSTRACT: Ground stresses are one of the significant factors in the context of rockbursts and underground instability at some hard rock mines in Canada. Overcoring strain relief measurements using triaxiaI strain eel is were performed at depths between 60 to 1890 m at several mine sites to provide stress data for stability analysis and optimum mine design. Pre-mining ground stress determinations from 64 stress tensor analyses resulted in the following average stress gradients: Maximum horizontal stress. -Hmax - 8.18 - 0.0122 MPa/m depth Minimum horizontal stress. _-,,min - 3.64 - 0.0276 MPa/m depth Average horizontal stress. -11, 5.91 - 0.03-19 MPs m depth Vertical stress. '-, - 0.0266 - 0.008 MPa/m depth The maximum and minimum horizontal compressive stresses. with an average ratio of 1.75 ,0..45. prevail in east--west and northerly directions. respectively. Horizontal compressive stresses in excess of vertical overburden load were determined. indicating large variations in ratios to a depth of about 1000 m with decreasing trend towards depth. From present data. a particular regional zoning for the magnitude and direction of horizontal stress fields cannot be outlined. A common feature at mines with near vertical orebodies is that the maximum horizontal compressive stress acts perpendicular to strike while the minimum horizontal compressive stress is aligned on-strike. The vertical stress components approach the gravitational overburden load.

Jan 1, 1989

By B. Caro Vargas

The Toulon South Tunnel in France is the second part of a project started 20 years ago. After the problems and delays suffered during the construction of the North Tunnel, due to a complex geologic context of highly fractured and soft rocks under a highly urbanized environment, a very dense automatic monitoring system was implemented to control the settlements of surface (more than 1000 points), the structures adjacent to the tunnel alignment and the underground galleries being constructed. The latest automatic instrumentation systems were installed, using for example AMTS capabilities in terms of ?automatic prismless settlement monitoring?. All the data (geotechnical, structural and geological) was gathered in a global automatic data acquisition system and continuously available on a web based interface. Three different threshold levels (notification, anomaly, alert) were set up, each one with a differential and an absolute value for settlements. Depending on the actual geological site conditions and the actual monitored settlements, different supporting systems and excavation techniques were used. Furthermore, the monitoring data was also used to predict and anticipate the future settlement, by comparing it continuously with the theoretical Peck settlement curves. This method allowed a better risk management by limiting the settlement on existing structures and helped to secure the Works progress schedule, for a project that lasts from July 2007 to March 2011. The implementation of this observational method application is presented in this paper.

Jan 1, 2012

By John D. Spencer

Projects aimed at achieving the least disturbance to the Nation's air, water, and land resources in the mining and utilization of coal continued to be a feature of the Bureau of Mines coal program. This reflects the current concern about damage inflicted on the environment by our growing and increasingly affluent society. Mine Health and Safety research, along with investigations related to all other aspects of coal extraction and use, also continued to be implemented and expanded.

Jan 1, 1970

The realization that there is a limit to our supply of domestic mineral and fuel resources, which have been taken for granted until recently, has stimulated the need for conservation and optimum utilization of the Nation's minerals, metals, and fuels-resources critical to our national economy. The mission of the Bureau of Mines is to develop new technology, improve existing technology, and disseminate information related to mineral resources and industries. Fulfilling the mission is necessary to insure a continuing, adequate supply of minerals and alternative supplies of energy from reliable sources at the lowest possible cost to society and the environment. Established in 1910, the Bureau of Mines under the Department of the Interior is the Federal Government's primary research arm in the mineral field. Since the transfer of the fossil fuels portion of the energy research program to the newly organized Energy Research and Development Administration (ERDA) in fiscal year 1975, Bureau research has been concentrated on increasing mineral production, decreasing energy usage through more efficient processing, and decreasing material losses caused by corrosion. Concurrently, research is being addressed to improved coal-preparation techniques, especially to expanding utilization of low-grade coals and coals difficult to beneficiate, which are essential for reducing the need for petroleum and natural gas supplies and for redirecting our energy consumption. Fluctuations in the availability of foreign sources of minerals, metals, and fuels due to political and economic variability among nations have necessitated intensified investigation into coal mining, uranium-ore processing, and geothermal energy sources-three alternatives that can help to alleviate the dependence of the United States on foreign sources of energy.

Jan 1, 1975

By Laurens de Jonge, Wiebe Boomsma, Rodney Norman, Stanislav Verichev

"Earth provides natural resources, such as fossil fuels and minerals that are vital for human life. As the global demand grows, especially for strategic minerals, commodity prices rapidly rise. Thus there is an identifiable risk of increasing supply shortage for minerals. Hence a major element in a long-term economic strategy must be, to ensure security of supply for these strategic minerals. In this rapidly changing global economic landscape, deep sea mining has gone from a distant possibility to a likely reality within just a decade.Although deep sea minerals extraction was investigated in the 1970’s, it was abandoned because of changing commodity economics, advances in on-land exploration techniques, growing concern on environmental impact, and political and legal aspects with regard to ownership issues. The developmental data from those days, if still available, are not adequate to allow engineering and building of an integral system for extraction of deep sea minerals without additional R&D work. Thus, deep sea mining is yet to attain a Technology Readiness Level (TRL) sufficient to successfully undertake deep sea mining operations, from resource discovery to resource assessment and to resource exploitation [Blue Mining, 2014]."

Sep 1, 2014

By Thomas R. Larson

"Many concentrators use re-circulating “plant” water for dilution in their flotation circuits. However, if crusher dust suppressants, ball mill grinding aids, or even agitator bearing grease are introduced into this water, and the water itself is not subject to cleaning steps, then sufficient quantities of these chemicals may appear in the flotation cells and begin to impact the flotation separation. A bench flotation procedure has been coupled with statistical analysis in order to estimate the impact of small quantities of non-flotation chemicals on flotation performance.INTRODUCTIONCleveland Cliffs produces iron oxide pellets for blast furnace feed, and is developing the capability to produce ferrous metallic products to supply a wider customer base. Cliffs manages five North American iron mines, including the Wabush mine sites in Labrador and Quebec. Based on various characteristics of the ore bodies, the flow sheets of the five mines are diverse. For example, Hibbing Taconite uses magnetic separation alone as their primary upgrading method, but Northshore and Empire use magnetic separation followed by flotation, and Tilden uses flotation alone. Last but not least, the Wabush concentrator upgrades primarily with gravity and electrostatic separation techniques.At Northshore, concentrate from the magnetic separator circuit is fed to a reverse flotation circuit. By design, the magnetic separators operate at the highest possible recovery of magnetite, as the separator tails are discarded, and relatively high silica content was acceptable to Northshore’s customers. As the steel-making industry moved toward lower and lower slag volumes, the silica content in the magnetic separator concentrate became a problem. The flotation step was added in the late 1980s in order to decrease the silica assay of the magnetic separator concentrate to meet the current customer requirements. In this setting, the flotation feed stream contains very little silica that occurs as liberated quartz particles. As the degree of liberation of the flotation feed stream is then a limiting factor for silica removal, the online grind control then was linked to flotation in the overall plant control system so that grind can be adjusted to achieve improved liberation if necessary for the flotation process."

Jan 1, 2002

By T. Y. Yunsel

Estimation techniques such as polygonal, triangular prism, trapezoid, isopach maps, and inverse distance methods are often used in ore or industrial minerals deposit evaluation. These techniques do not express the variability of the deposit and do not allow a determination of the reliability of the estimates. However, geostatistical methods can express a measure of the error associated with the estimates, by finding weighting coefficients for a given mining block, and can also help with data configuration that minimizes the error. This work addresses an application study on the quality and reserve characteristics of the cement raw materials of the Adana Cement Factory in Adana, Turkey, based on the spatial distribution and variability of the chemical components (Si02, CaO, A1203, Fe203). The study has been carried out using a geostatistical procedure that is useful for site assessment, characterization, and monitoring situations where data are collected spatially. Directional and omnidirectional experimental variograms of the cement raw material variables showed that neither strong geometric nor severe zonal anisotropy exists in the data. The most evident spatial dependence structure expressing the continuity for omnidirectional experimental variograms were characterized by exponential and spherical variogram models. These models have been used in cross¬-validation analysis, which proved that these models, their parameters, and kriging parameters are applicable for the study area. Quality contour maps of the deposits at given levels underground were estimated using a kriging interpolation technique. Anomalies such as bullseyes and drift were not observed in the maps that were generated. Kriged maps showed the spatial distribution of quality continuity and variability of the deposits. Grade-tonnage curves and total tonnage estimates in the particular grade were determined using ordinary kriging in order to improve the mining operation and planning. Consequently, local uncertainty and the probability of extreme values occurring are tools of prime importance for the mine planning, the optimum mix of raw materials coming from different quarry stopes.

Jan 1, 2012

The workshop on "Cyanide Effluents from Mineral Processing' was held on February 2-3, 1982, at the U.S. Bureau of Mines, Salt Lake City Research Center, Salt Lake City, Utah. The workshop was sponsored by the minerals industry, supporting industries, the National Science Foundation, and the U.S. Bureau of Mines through the Utah Mining and Mineral Resources Research Institute, College of Mines, University of Utah Prior to the workshop, a Working Paper was prepared and delivered to the participants. This paper was used as a guide during panel discussions and forms the basis for this proceedings document. The workshop focused on use of cyanide as it relates to the gold and silver mining industry and the froth flotation processes employed by mineral mining companies. Its intent was to discuss "state of the art" technology and provide information pertinent to cyanide use in the minerals industry. No attempt was made to advocate regulatory limits or set policy governing the use of cyanide. The principal topics of discussion included- (1) the chemistry and use of cyanides; (2) control and treatment of cyanide mining wastes; (3) toxicity of mining wastes; (4) fate of cyanide in the environment; and (5) the analytical chemistry of cyanide.

Jan 1, 1983

By J. R. Thoenen

Occurrences of titanium, zircon, and other heavy minerals are widespread in Florida. Deposits concentrated as "heavy sands" by wave and wind action have been mined an or near Atlantic coastal beaches since 1916. An important inland concentration at Trail Ridge; .believed, to have formed along an ancient share line, was disclosed by preliminary investigations (1947) by the Bureau of Mines. This report describes investigations to determine the extent and grade of "heavy-sand" concentrations in other inland stabilized dune areas in the central and northeastern parts of the peninsular region of the State (fig. 1). Portions of the central highlands south of Trail Ridge and terraces and dunes in the coastal lowlands region, east and northeast of the ridge were investigated. Holes were drilled in 10 areas (see table 1 and fig. 2) along State and County roads and on private property. They were spaced 250 to 2,000 feet. apart to obtain a cross-sectional picture of "heavy-sand" content in the dune areas. These sections were generally placed in east-west directions normal to the general trend Of the peninsula to intercept one or more of the ancient shore lines in the various areas (figs. 3 to 13, incl.). A total of 433 drive piped and 333 jet holes were drilled, and 7,293 bulk and core samples were taken. Intermediate holes were placed at closer intervals when field analysis indicated 1 percent or more of heavy minerals present. All of the holes drilled and the analysis of samples that contain 1 percent or more of heavy minerals are listed in table 2. Profiles (figs. 14 to 20, inclusive) show the more favorable concentrations, which are irregular in outline and erratic in mineral content. The highest concentrations averaged 1.0 to more than 2.0 percent heavy-mineral content, but a few individual hole samples exceeded 3.0 percent in grade.

Jan 1, 1949

THERE are certain facts that the mining industry in Australia is faced with at the present moment which may be accepted as axioms. The industry is at a low ebb, as evidenced by statistics. Metals form the basis of all modern industries, and are necessaryfor the welfare of Australia. Mining is a wasting asset. Every ton of ore extracted is one ton less which c.annot be made good, and it should be our duty to get as much profit froin that ore as possible, otherwise there is a permanent loss to the country.The metal market cannot be controlled by Australia; it is more or less an international matter. Australia has not been thoroughly prospected. There are no mines being developed that are likely to replace those which are being depleted.Our mining engineers are as capable as those in other parts of the world, and have made good where they have been given a chance. There is no one cause for the present depression; there are several, more or less, interwoven. Of course, the war has had an adverse effect, but that has only dislocated things temporarily; it upset our markets, influenced the price of metals, and affected the labour market and cost of stores. Labour troubles made their appearance before the wave of unrest swept over the world. The cause of labour discontent must be investigated, and if possible removed. As each industry has .its·own problems, miners must inquire into their special problems, as there is no sovereign remedy that will suit all cases.It is obvious that we cannot mine ore if we do not know where it is; therefore, the first thing is to discover workable deposits.

Jan 1, 1919

By A. J. Kauffman

This inventory of the industrial mineral resources of the Pacific Northwest indicates that each of the States comprising this great region annually produces nonmetallic materials valued at mans million dollars. Commodities or their products that have a large, localized market predominate. These include Portland cement, sand and gravel, stone, clay, and lime. The region's output of magnesite, vermiculite, pumice, and diatomaceous earth is outstanding. The magnesite deposits of Stevens County, Wash., are the largest and most important in this country. Mast of the domestic vermiculite production is obtained from deposits in Lincoln County, Mont. Oregon and Idaho rank third and fourth, respectively, as domestic pumice producers. Production data for diatomaceous earth show Oregon second and Washington fourth among the producing States.

Jan 1, 1952