Search Documents

By Warren Hastings

This paper describes the methods and costs, in units of labor end materials, of sinking a 7 compartment vertical shaft 1,261 feet through a fractured, water-saturated formation. The shaft, designed for hoisting 2,500 tons a day, is at Friedensville, Lehigh County, Pa., approximately 6 miles south of Allentown and Bethlehem. It was sunk by the E. J. Longyear Co. under contract to the New Jersey Zinc Co. Preparation for shaft sinking W8A begun July 1, 1947, and sinking was completed August 18, 1952. A total of 604,858 man hours was required to sink the shaft.

Jan 1, 1954

By Leonard F. Heising

At the Groveland-mine iron ore is mined by open-pit methods and concentrated by means of spirals and flotation. A brief history of the mine and its early development is given. The ore deposit is described, with emphasis on those physical characteristics that affect the choice of mining and milling methods. Development and mining, which include breaking ground, loading, transportation, engineering, and operating control; are explained, and the milling method is described Mining and milling costs are given in percent of total cost.

Jan 1, 1963

By O. C. Blade

"INTRODUCTION This report on the properties of motor fuels sold through service stations in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between the Coordinating Fuel Research (CFR) Com¬mittee of the Coordinating Research Council (CFC) 3/ and the Bureau of Mines of the United States Department of the Interior. The first of these reports presented data on motor gasolines sold during the winter of 1935-36. 4/ Further re¬ports were issued describing motor gasolines sold during the succeeding summers and winters to and including the summer of 1941.4/ No reports were made on motor gasolines sold during the winter of l941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed. The present report presents analytical data for 3,011 samples, representing the products of 113 companies. Most of the samples represented in this report were obtained during July and August 1946. As in previous surveys the companies covered by the survey include both large and small suppliers. Conforming to former reports, the data cover three groups of samples - regular-price, premium-price, and third-grade gasolines.As the number of analyses submitted for samples of third-grade gasoline are not considered adequate to represent this type of motor fuel, data for the analyses have not been averaged, but the individual items are tabulated. The number of samples, items, and brands comprising each group is as follows: Regular-price, 1,585 samples, 311 items, and 99 -brands; premium-price, 1,422 samples, 280 items, and 94 brands; third-grade, 4 samples, 4 items, and 4 brands. The meaning of these terms as used in the survey is as follows:"

Dec 1, 1946

By G. M. Ault, G. C. Deutsch

The paper reviews the efforts made to utilize powder metallurgy to solve problems encountered when using alloys at high temperatures. The following subjects are discussed: comparison of wrought and sintered super alloys, sintered aluminum powder, porous materials for transpiration cooling, molybdenum, and cermets. TODAY, powder-metallurgy techniques are be-JL coming increasingly important, producing materials which at the present time cannot be made by any other method. Among these materials are high melting-point metals such as tantalum and tungsten, porous metals for filters and lubricant-containing bearings, electrical contacts and electrodes (i.e., tungsten-copper), cutting tools of the cemented carbides, and magnet alloys. In addition, the powder-metallurgy industry has grown because, through the application of its methods, shaped parts, such as gears, can be produced at tremendous rates with a low scrap loss in comparison with manufacture by casting or forging and machining. In the past few years, by utilizing powder metallurgy, several approaches to the problem of high temperature materials have been investigated. In this paper the authors will review some of the studies on application of materials having properties above 1350°F. Since their experience lies in the aeronautical field, possible uses of powder-metallurgy techniques in the production of aircraft en- gines will be emphasized. A large portion of the work is classified, but such a restriction has not eliminated any field from discussion, although limiting the amount of detail it is possible to present. The development of high temperature alloys from powders and porous metals for cooling will be discussed as well as research done on molybdenum and molybdenum alloys, cermets, and intermetallics. Some studies on the utilization of cermets will be considered along with special problems that have been revealed through these investigations. Special interest in certain factors of sintered aluminum powder (SAP) makes it desirable to discuss this material although its use temperature is below the 1350°F limitation set for this paper. High Temperature Alloys from Powders In general, components made from powders for room-temperature application have been investigated with the primary purpose of taking advantage of the high production rates and economies made possible by powder metallurgy. From the standpoint of properties, the ojective of the powder metallurgist has been to obtain a product comparable to the cast or wrought product that is to be replaced. Comparisons of the properties of alloys made by powder-metallurgy methods with those of similar compositions made by casting and forging are reported in the literature.12 In many cases equivalent

Jan 1, 1955

By L P. Trout, D G. Reid

PanAust Limited (PanAust) has successfully constructed and commissioned two mining operations in Lao PDR over the past decade and undertaken major studies for three new mine developments. The management of potentially acid generating mine waste and tailings in close proximity of local communities sensitive to water discharge quality have been recurring themes that have confronted PanAust’s project study, development and operational teams. Further compounding challenges, such as the effects of intense annual tropical monsoonal conditions, staging of embankment raises and regular lifting of spillway structures, integrating mine waste and tailings management into production plans and ensuring the long term stability of structures, have been addressed by implementing leading practice management solutions.A recognition of the criticality of managing the substantial business risks associated with these crucial activities led to the early establishment of a governance structure to ensure that the highest standards are embraced for planning and execution. Importantly, these are guided and monitored by a panel of highly experienced and qualified international specialists reporting directly to PanAust’s Managing Director – the Tailings Independent Review Panel. The stewardship process has been effective in identifying potential shortcomings in management systems and has led to enhanced executive commitment to risk informed designs, assurance and overall process rigour.CITATION:Trout, L P and Reid, D G, 2018. PanAust Limited’s approach to mine waste and tailings stewardship, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 135–155 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By D R. Anstey

The growing demand for iron ore from Western Australia has led to an increased focus on the development of magnetite and lower grade iron ore deposits. The need to process and beneficiate the ore from these projects can result in the generation of significant quantities of iron ore tailings over the life of a project. Over the coming decades, the management of iron ore tailings will become a significant aspect of the mining landscape in Western Australia.The tailings generated from iron ore projects differ signifi cantly from other mineral tailings currently produced in Western Australia. Iron ore tailings are generated on a scale not matched by any other mineral process and can often contain asbestiform or potentially acid forming components. New iron ore projects are coming under increased environmental scrutiny because of their large scale operations and the sensitive environments in which they occur. This combination of factors creates some unique challenges for the management of tailings generated by iron ore mining in Western Australia.This paper presents the fi ndings of two studies conducted in recent years to overcome the challenges posed by iron ore tailings. The paper discusses the role of laboratory testing in the development of management strategies for asbestiform minerals in tailings. It also presents a numerical modelling approach for evaluating the rates of rise in the storage of magnetite tailings. The paper concludes by outlining how the findings of these studies can be applied to reduce tailings management costs, lower risks and improve environmental outcomes for the management of tailings from iron ore mining.

Jul 11, 2011

By Y. Luo

This paper presents a number of mathematical models for predicting the different phases of the complete surface subsidence process associated with underground longwall mining. A computer program developed based on the mathematical models is briefly introduced.

Jan 1, 1992

By D P. Blair

Rio Tinto’s Hope Downs Operations are currently mining iron ore in their South Central Pit. Prior to the commencement of mine operations, Hope Downs carried out an extensive archaeological investigation and identified an ancient rock shelter lying within the proposed mine boundaries. The site is significant to the traditional owners/custodians of the land in this part of the Pilbara, and thus the final pit design was changed to preserve the rock shelter, which now lies 30 m outside the mine boundary. In order to further preserve this ancient dwelling from blast-induced damage, blast design procedures were improved over time to minimise the vibration impact when blasting close to the shelter. Blasting and vibration monitoring commenced in May 2008 using pyrotechnic delay sequences and normal-direction firing. In October 2009 electronic delays were used to reverse-fire blasts close to the shelter in order to create a damage zone between the initiating holes and the rock shelter. A detailed statistical analysis of the vibration data shows a reduction in the higher levels of vibration for blasts fired after October 2009, which is most likely caused by the created damage zone. In May 2010, a site-specific vibration model was developed and implemented, and based on Monte Carlo waveform superposition. This model was used to give a further insight and improvement to the blast delay sequences when blasting close to the shelter. However, such models are expensive to implement and have limitations, which reduces their potential for estimating the probability of getting an excessive vibration due to a given blast design. In this regard, it is more realistic and significantly less expensive to use a recently developed probabilistic analysis based on simple charge weight scaling. This analysis shows that there was a higher probability of exceeding prescribed vibration limits at the rock shelter for blasts fired before October 2009 than there was for blasts fired after October 2009.

Nov 8, 2011

By Chu E. Ho, Paul Napoli

A new waterfront park was developed on Long Island in close proximity to the East River and Newtown Creek. The existing ground consisted of fill over soft organic clay, medium dense silty sand, glacial till and schist bedrock. The ground was initially raised to preload the underlying soft soils to stabilize the ground in preparation for site development. The ground was subsequently cut down to temporary grades for installation of foundation piles for the overlook structures and construction of reinforced concrete cantilever retaining walls forming pathways located adjacent to the water bodies. The retaining walls were located in two rows at different elevations along the sides of a steep embankment. Where the pathways converge, some of the walls were too close to each other, and were redesigned as a combined U-wall with a common base slab. The individual retaining walls were designed for adequate bearing, sliding and overturning resistance. Ground anchors were installed to enhance global stability of the retaining walls. This paper presents the design considerations for the retaining walls for various loading conditions, and evaluation of the trial and proof tests for the anchors. INTRODUCTION The New York City Master Plan included the transformation of an approximately 30-acre parcel of land in Long Island City, Queens, New York from a former manufacturing zone into a residential, commercial and recreational zone for middle-income community. The site was located at Hunters Point South along the eastern shoreline of the East River and Newtown Creek (Figure 1). The development included low to high- rise residential buildings, a public school, and retail structures. Open spaces were provided along the East River and Newtown Creek waterfronts in the form of a continuous park providing for recreational and community-related activities. Waterfront structures included small park buildings, walkways and viewing platforms. The shoreline was surrounded by revetments as part of the flood mitigation strategy. The project involved extensive site re-grading and several retaining walls were constructed. The earthwork volume amounted to approximately 47,000 cubic yard of imported fill and 93,000 cubic yard of cut. The exposed height of the retaining walls ranged from 3 to 15 feet. This paper focuses on the design and construction of the retaining walls for the project.

Jan 1, 2019

By P. T. Bissert, L. Yan, J. R. Srednicki, J. A. Yonkey

"Refuge alternatives (RAs) are required in underground coal mines to support life post-disaster. RAs are mandated by MSHA to maintain an apparent temperature (AT) at or below 95°F (35°C) while providing a safe and livable shelter for a minimum of 96 hours. Because strata composition and mine temperatures will affect the final AT within an occupied RA, NIOSH researchers have collaborated with five underground coal mines across the US to characterize the effects of geographic location and seasonal temperature fluctuations on mine air temperature, relative humidity, and mine strata temperatures. The data collected indicates that some mines will experience greater temperature fluctuations than others, based on geographic location. The mine which demonstrated the greatest temperature differential over the course of the year resulted in a mine air temperature that ranged from 53.4°F (11.9°C) to 84.2°F (29.0°C) and a rib surface temperature that ranged from 55.4°F (13.0°C) to 82.8°F (28.2°C). This data suggests that the location and seasonal peak temperature can significantly affect the mine strata temperature, which could lead to a fully occupied RA exceeding the 95°F (35°C) AT limit over the course of 96 hours. The data reported in this paper could be used to examine the heat buildup inside an RA for actual mine conditions. Thermal simulations could be implemented to evaluate maximum occupancy ratings based on actual mine temperatures and strata compositions. INTRODUCTION In the event of a mine disaster, miners’ primary focus is to escape. Should their attempt be futile, they can enter a refuge alternative (RA) to await rescue. In 2008, the Mine Safety and Health Administration (MSHA) mandated that underground coal mines implement RAs within 1,000 ft (304.8 m) of the working face and spaced within one-hour travel distances in outby areas where persons work such that persons in outby areas are never more than than a 30-minute travel distance from an RA or safe exit. These RAs are required to provide a safe and habitable shelter for a minimum of 96 hours and to prevent the apparent temperature (AT) from exceeding 95°F (35°C) [1]. There is concern throughout the industry that in some cases the internal ambient of occupied RAs may exceed the 95°F (35°C) AT limit due to the potentially hot mine atmosphere as well as the metabolic heat generated by RA occupants and the carbon dioxide scrubbing system. The National Institute for Occupational Safety and Health (NIOSH) has conducted tests in its Safety Research Coal Mine (SRCM) and its Experimental Mine (EM) to investigate heat buildup in RAs. It was found that the number of occupants in an RA may need to be reduced based on the ambient mine temperature, which varies from mine to mine [2]. Further testing and analyses were completed to evaluate the mechanisms (conduction, convection, radiation) by which heat is transferred from an RA to the mine surroundings. Additionally, the effects of varying mine strata compositions on the heat buildup inside an RA were studied [3]. The mine strata temperatures will increase due to heat transfer from within an RA. Depending on the mine strata composition, some mines may be more thermally conductive than others. For example, sandstone is much more conductive than shale or coal (i.e. it disippates heat at a quicker rate). All things being equal, the air temperature inside of an RA after 96 hours will be higher for a mine with strata that has low thermal conductivity compared to a mine with high thermal conductivity."

Jan 1, 2017

By G. R. Hopkins

The petroleum-refining industry established a new record in fuel efficiency at refineries in 1936, when 597,000 B. t. u. of heat were required to refine a barrel of crude oil, compared with an average of 615,000 B. t. u. in 1935 (see fig. 1). The principal factor in the "indicated gain in fuel efficiency at refineries in 1936 was an increase in crude runs of 11 percent over 1935. A large part of the heat utilized at refineries is consumed elsewhere than under stills, or in ways quite independent of crude-oil distillation. In other words, as the operating ratio (crude runs divided by capacity) for refineries increases toward the maximum of 100 percent, the fuel requirements show progressively smaller increases and the average E. t. u. consumption per barrel of crude refined declines.

Jan 1, 1938

By Robert M. Grogan

Fluorspar is the commercial name for fluorite, which is the mineral having the composition CaF2, calcium fluoride. Its valuable properties are due to its content of fluorine, and it is the only important commercial source of that element. The name is derived from the Latin fluere, to flow, because the mineral melts easily and is a good flux. History The mineral has been known since Greek and Roman times, when it was used for drinking cups and ornamental slabs. Various peoples including the Chinese and the American Indians have carved ornaments from large crystals. Its usefulness as a flux was known to Agricola, who wrote about it in 1546.1 Mining began in England about 1775 15 and at various places in the United States during the period 1820 to 1840.28 Substantial production was achieved first in the period 1888 to 1900 in consequence of the development and widespread adoption of the basic open hearth method of making steel, in which fluorspar is used as a flux. After that, production and usage was stimulated by growth in the steel, aluminum, chemical, and ceramic industries and accelerated by World Wars I and II. The organic fluorides called "Freons" entered the picture in 1931, and the use of anhydrous HF as a catalyst in the manufacture of alkylate for high octane fuel blends began in 1942. The development of the froth flotation process in the late 1920's, a differential flotation scheme for separating fluorspar from galena, sphalerite, and other minerals in the 1930's, and the application of heavy-media concentrating methods to the treatment of low-grade ores in the 1940's were outstanding technological contributions that enabled increased production of fluorspar concentrates. Composition and Properties Fluorite in its purest form contains 51.1 pct calcium and 48.9 pct fluorine. Substitution of small percentages of cerium and yttrium for calcium have been noted.4 Mechanical inclusions of gases and fluids such as petroleum and water, and of other solid minerals such as pyrite, marcasite, and chalcopyrite are common. The fluorspar of commerce contains attached and admixed mineral impurities, chiefly calcite, quartz, barite, celestite, and various sulfides. It is interesting that the purest commercial form in which the mineral is sold, acid grade concentrate, contains a minimum of 97 pct CaF2, and as such is of comparable purity to many reagents used in chemical laboratories. Fluorite has a marked tendency to occur in large, well-formed crystals sometimes six to ten inches on a side. It crystallizes in the isometric system, frequently forming cubic and octahedral crystals or combinations thereof. The mineral also occurs in massive and in earthy forms, and in crusts or globular aggregates with radial fibrous texture. Crystalline fluorspar exhibits a great array of colors, from colorless and water clear to yellow, blue, purple, green, rose, red, bluish and purplish black, and brown. The colors are often arranged in alternating bands parallel to cube faces. They may be altered by exposure to X-rays, heat, ultraviolet light, and pressure, and are caused by a variety of factors including the presence of trace impurities and displaced ions in the lattice. Sometimes the changes induced by X-rays can be reversed by ultraviolet radiation. The mineral has a hardness of 4, and is the model of that hardness on the Mobs scale.

Jan 1, 1960

By E. T. Turner

Introduction 1n assembling material for this paper on Wood Refuse Burning 1 turned first to the records of our early studies of the problem in order to learn how and why certain basic decisions were arrived at and also how it came about that the completed central steam plant differed so much from the original plans. It may be of interest, therefore, to outline the engineering problems as they presented themselves in the early part of 1948, and to indicate the economies involved. Although the principle of using wood refuse as boiler fuel instead of burning it to waste was quite sound, and in fact the practice had been in use for a long time in the boilers of many lumber companies, there was some guesswork as far as Hollinger was concerned in deciding how best to handle the large quantities of wood refuse involved and as to the type of boiler equipment necessary to .burn it efficiently. These problems will be examined first. Hollinger Boiler Equipment in 1948 Hollinger had four separate boiler houses, at Main, No. II, and No. 19 shafts, and a small unit at the compressor plant for heating purposes. Main and No. Il boiler houses operated all the year round; No. 19 and the compressor plant only in the winter. At Main there were four 36-year-old HRT boilers with total available h.p. of 500, at No. II, three 30-year-old HRT boilers with 195 available h.p., and at No. 19 two old field-type locomotive boilers capable of producing 95 h.p.

Jan 1, 1951

By Jerry J. Gray

The utilization of secondary titanium was determined in a study by the Bureau of Mines, and a 10-year statistical table showing supply and distribution patterns is presented in this report. Over the total 10-year period, estimated scrap consumption is larger than estimated scrap supply. Trends from the estimated data indicate that titanium is in short supply and probably will continue to be in the future. Because of higher processing costs for recycle scrap, scrap will tend to migrate to the steel and aluminum industries and to ferrotitanium production and exports. Nonrecoverable losses of titanium metal during processing was determined to be a potential area for research.

Jan 1, 1971

By Donald A. Dahlstrom

In 1961 it became increasingly more evident that significant technological changes must be made in minerals beneficiation. The status quo in technology in today's competitive markets will not be tolerated. Higher productivity, greater recoveries and newer and better products must be sought and incorporated with lower operating costs. In other words, "when you build a new mill, don't build an old mill." Recommended reading for proof of the vital necessity of new methods and techniques is in the September 1961 issue of MINING ENGINEERING. The article by one of MBD's cherished and true veterans, E. H. Rose, is entitled "Iron Ore: The BIG Picture". Because of new beneficiation methods for iron ores, nearly 47 million tons of plus 60% iron concentrates will be produced and another 40.1 million tons of capacity will be under construction or committed. Thus in a relatively short period, 87 million tons of this high-grade iron concentrate with record low silica will be available. As Mr. Rose also points out, "in gross tons, without allowance for better grade, this is the equivalent of almost exactly two-thirds of all iron ore used for all purposes in the U.S. and Canada in the peak years of 1953 or 1957." Needless to say, improved mineral beneficiation methods have had far more reaching effects than just the production of higher grade iron concentrate.

Jan 2, 1962

By Savage E. N

The porphyry copper minerals of Melanesia occur within a host of narrow veinlets in predominantly quartz diorite stocks or as contact metasomatic masses in skarns adjacent to the intrusion. Some 90 per cent of the constituent minerals comprise pyrite or marcasite, chalcopyrite, and magnetite with the remainder mainly bornite and hematite with accessory rutile and chalcocite together with several trace minerals. Gold is found mainly as inclusions in chalcopyrite, and minor molybdenite occurs likewise.Of particular significance is the persistent occurrence of accessory rutile of hydrothermal origin intimately intergrown with chalcopyrite. The rutile occurs relatively late in the hydrothermal sequence and upon weathering of the deposit may be released on a cumulative basis possibly in sufficient amounts to constitute a particulate pathfinder mineral which may aid in prospecting.Rutile is present in all the Melanesian occurrences studied and is also prominent in several American deposits.The porphyry copper mineralogy is characterized by the presence of accessory hydrothermal rutile intergrown with chalcopyrite.

Jan 1, 1975

This publication summarizes, for potential contractors and other interested parties, the proposed research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1977 (October 1, 1976-September 30, 1977) under its Advancing Coal Mining Technology program. The objective of these projects is to provide an ordered and sequenced series of advances toward the overall goal of providing the system technology required to increase the productivity of the coal mining process.

Jan 1, 1977

By John C. Edwards

The Bureau of Mines developed a mathematical model to predict the oxygen requirements for a miner evacuating a mine. The model accounts for variations in the miner's escape speed with mine airway height, and for the empirically determined expressions for the weight-specific oxygen uptake rate for upright walking, stooped walking (duck-walking), and crawling. A Fortran computer program that is user oriented was prepared based upon the model's constitutive equations. Specific instructions for utilizing the program, as well as applications to miner evacuation from a mine, are presented.

Jan 1, 1986

By Earl Bardwell

THE determination of suitable and safe annealing temperatures is one of the most important problems arising in the operation of a copper rolling mill. Certain of the larger mills have worked this problem out for themselves and in these mills the operation has become more or less standardized. In some of the mills pyrometers are used to measure the temperature of the annealing furnaces and careful watch is kept to see that overheating does not take place. In a considerable number of the mills, however, dependence is placed entirely on the judgment of the operator. The almost total lack of literature bearing on this subject seems sufficient warrant for the publication of this paper. The discussion of this subject naturally divides itself into two parts: (1) The effect of annealing temperature on physical properties; and (2) changes in the microstructure of refined copper due to cold rolling and annealing. I. THE EFFECT OF ANNEALING TEMPERATURE ON PHYSICAL PROPERTIES For the purpose of investigating this phase of the subject six test bars were selected, varying in oxygen content between the limits of 0.036 and 0.070 per cent. The chemical composition of each of these test bars was as follows:

Jan 8, 1914

By Behl S

Flocculation behaviour of six different dolomite samples, four from the Florida mining district, one from Perry, South Georgia and another from New Jersey was examined using polyethylene oxide (PEO) as a flocculant. The samples were similar in chemical composition, however the porosity of the samples from the Florida mining district was higher than the others. FT-IR, adsorption and surface modification by leaching revealed that flocculation was directly related to the presence of isolated hydroxyl groups on the surface. The adsorption mechanism was believed to be hydrogen bonding of the ether oxygen of PEO with isolated -OH sites on the solid.

Jan 1, 1993