Search Documents

By Hee-suk Yun, Dae-jin Hwang, Jeong-woo Seok, Myoung-mo Kim

"In this paper, the accuracy of the data measured by a newly developed displacement measuring system, DPRMs (Digital Pile Penetration and Rebound Monitoring system) and its applicability as a quality control tool were verified by field measurements of pile penetration and rebound for pile driving performed at 3 construction sites and 1 test site. The DPRMs data were found to be much better than handwork data. A new dynamic formula for pile capacities is proposed uses the results of a pilot dynamic load test and the final pile penetration. The ratios of pile capacities obtained by the new formula to those by the dynamic load test were 94%±7.4% in the contrast with 123±28.3% by the 5S formula and 68±24.0% by Hiley's formula. This result shows the superiority of the new formula. The ratios of the maximum compressive stresses calculated by using DPRMs to those calculated by using PDA (Pile Driving Analyzer) were about 90-110±10%. This result confirms the applicability of DPRMs as an overdriving monitoring tool. Two sets of DPRMs were used to measure the 3-D displacement behavior of a pile head at the test site. The more the pile head moves laterally, the less the final set values were expected because of the loss of driving energy, but this trend was not obvious within the limited data obtained at the test site.INTRODUCTIONPile construction monitoring consists of two parts. In the first part, enough capacity of the pile is secured to stand the design load. In the other part, pile damage during driving is prevented. Although several methods can be applied to achieve the first part, PDA is nearly the only tool for measuring pile stress.Several methods such as a static load test, a dynamic load test, an Osterberg cell, and numerous driving equations can determine the pile capacity. Among them, the static load test and the dynamic load test are most widely used. The static load test is advantageous because it has the highest reliability. The disadvantages are as follows: it is costly and time-consuming. Also, the capacity of the pile under construction cannot be evaluated. The dynamic load test has lower reliability than the static load test, but it is cheaper than the static load test, is reliable enough to determine the pile capacity, can evaluate the capacity of a pile during construction, and can offer information about construction conditions such as the pile integrity and the pi le stress during driving. The dynamic load test takes a relatively short time and is low cost compared with the static load test. However, it is still costly, time-consuming, and unnecessary to apply to all piles in the field as a construction measurement tool. Therefore, driving resistance (blowcounts) is commonly measured to confirm the pile capacity at construction sites."

Jan 1, 2005

By B. K. Gorain

"The Air-Metabisulfite (AMBS) process has been developed to treat complex copper, molybdenum and precious metals (gold, silver) bearing ores using brackish and sea water. This process was able to produce significantly better copper concentrate grades and higher recovery than possible using conventional lime and/or cyanide based processes for certain complex ores with high sulphide gangue minerals. The AMBS technology in now used commercially following a rigorous evaluation process emanating from laboratory curiosity to plant applications. In addition, many projects have embraced this technology at a feasibility level involving various complex ore bodies.This paper presents a summary of the findings from testing the AMBS technology on various ores types. Experiences gained from this successful development from bench to piloting and then to plant applications are also presented in this paper.INTRODUCTIONProcessing of sulphide copper, molybdenum and precious metal ores typically involves flotation of copper bearing minerals while depressing non-sulphide and other non-copper sulphide minerals such as pyrite, pyrrhotite and sometimes arsenopyrite. Though in many precious metal ores, the values are in these sulphide minerals as well. The conventional method employed in the industry to produce a saleable copper concentrate requires depression of these non-copper sulphide minerals using an alkaline pH above 9.5, though 10.5 to 11.5 is more common. Alkalinity is controlled by the addition of a pH modifier. Lime is normally employed as a pH modifier due to its relatively low cost; however, the costs associated with adding lime can be significant and the effectiveness of lime as a depressant could be drastically reduced when the process water supplied to the flotation circuit contains high level of dissolved salts. In some cases, a small amount of cyanide is used along with lime to depress non-copper sulphide minerals especially when its proportion to copper sulphide minerals in the ore is higher than three."

Jan 1, 2016

By L. Bryson, J. H. W. M. Brits, K. Voogt

"The Anglo American Platinum’s Rustenburg Base Metals Refinery (RBMR) has the world’s first full deposit nickel plating tankhouse. Impurities in the nickel electrolyte can induce stresses in the electrowon nickel deposits that could lead to delamination of the deposit. Identifying the impurities that contribute to increasing internal stresses in the nickel deposit is key to successful operation and automation of the tankhouse. Impurities were introduced in the plant electrolyte and the effects on the full-scale nickel deposits evaluated. The impurity-adjusted electrolyte solutions were also analyzed using commercially available bench-scale methods to determine the induced stress. A correlation between impurity-induced deposit stress and full-scale delamination was developed. A direct correlation can now be made between feed quality, i.e. impurity concentrations, and degree of delamination in the plant. This methodology has the potential to rapidly predict the effect of new reagents, upstream process upset conditions and synergistic interactions between impurities on deposit stress and delamination of nickel deposits.INTRODUCTION Nickel electrowinning in sulphate media was first pioneered by Outokumpu in its Harjavalta refinery in 1960 (Saarinen and Seilo, 1985). The original process was very manual with starter sheets plated onto “acid resistant” steel for 36 hours and then manually stripped and cut into sheets which could be inserted into the main production cells for a further 4–5 days. The starter sheet stripping and manufacture process was later automated. The same technology was subsequently implemented on a number of plants around the world. Anglo American Platinum’s Base Metal Refinery (BMR) began nickel electrowinning in the early 1980’s. The recent expansion of Anglo American Platinum’s Base Metals Refinery necessitated the construction of a new nickel tankhouse to achieve two primary objectives. The first to increase the capacity to 32 400 tpa nickel and the second to reduce employee occupational exposure to nickel aerosols. The new tankhouse has been commissioned and is in the process of ramp-up; more details are given by Hagemann et al. (2016). Fundamental to lowering employee exposure to aerosols was automating both harvesting and final handling of cathode. In order to accomplish this a bold move was taken to plate up to 10 days on permanent titanium blanks which are harvested by automatic crane and automatically stripped. The original development work for the plating nickel on titanium blanks over a ten day cycle is given by Bryson et al. (2006)."

Jan 1, 2017

By H. M. Howe

Page 1. Introduction............................514 2. Definitions.............................517 3. Brevity of the Heating........................517 I. THE HARDENING OF THE BORE..............517 4. The Hardening of the Bore.....................517 5. The Thickness of the Hardened Layer.................517 6. Martensitization..........................518 7. The Hardening Repetitive ......................519 8. The Temperature Cycle.......................519 9. The Hardened Layer is the Merged Layer............... 521 10. The Progressiveness of Merging....................521 11. The Progressive Thickening of the Hardened Layer from Round to Round. 523 12. Merging and Hardening are Cumulative................523 13. Three Additional Causes of the Progressive Thickening of the Hardened Layer 525 14. Progressive Roughening of the Bore..................525 15. Avoidance of an Endothermic Transformation.............525 16. Asymptotic Retardation of the Thickening of the Hardened Layer.....527 17. The Troostitic Layer........................ 529 18. The Usual Lack of Martensitic Markings................529 19. The Thickness of the Hardened Layer Should Increase with the Quantity of Heat Taken up by the Walls of the Bore.................530 20. The Decrease of the Thickness of the Hardened Layer from Breech to Muzsle 531 21. Phstic Deformation as a Contributory aCause of Hardening........531 22. In What Way May Plastic Deformation Hasten Hardening?....... 535 23. Possible Need of Coarsening.....................535 24. Carburization as a Cause of Hardening..........:.....536 25. Does Hardening Increase Erosion?..................-538 11. THE CRACKING OF THE BORE ...............539 26. Appearance of the Bore and Cracks in Elevation............539 27. The Cracks in Elevation in the Rear Ring...............539 28. The Cracks in Elevation in the Forward Ring.............540 29. The Copper Network in the Grooves.................540 30. The Cracking of the Lands......................541

Jan 1, 1918

By Jonkion M. Font

An expression for the distribution ratio of arsenic between slag and copper matte or liquid copper was developed by both, an extension of the Reddy-Blander moderl for deriving a priori the arsenic capacity, and by a relationship between the arsenic capacity and the arsenic distribution ratio. In this study, the a priori arsenic capacities in the FeO-SiO2, CaO-SiO2,MgO-SiO2, FeO-CaO-SiO2, FeO1.5-CuO0.5-MgO-SiO2, FeO-FeO1.5-CuO0.5-CaO-Mgo and FeO-FeO1.5-CuO0.5-CaO-Mgo-SiO2, slags were calculated at 1573 K. The a priori arsenic distribution ratio between the FeO-FeO1.5-CuO0.5-CaO-MgO-SiO2 slag and copper matte mn (Lx, )' and between the FeO-FeO1.5-SiO2 or FeO-FeO1.5-CuO0.5*-CaO-Mgo slag and liquid copper (Ls/cua) were calculated. The model calculated data are found to be in good agreement with the reported experimental data. The availability of reliable thermodynamic data for slag components and impurities in the slag-matte- metal system is essential for the accurate prediction of impurity capacities and distribution ratio data. The arsenic distribution ratio model developed here, can be extended for predication in multi-componet slags and mattes or liquid metal, and thereby may lead to the development of new slag systems for the efficient removal of arsenic in the copper smelting, converting and refining processes,

Jan 1, 2003

By K. Y. Haramy

Deep coal mines with strong roof and floor rock frequently encounter face and rib bursts. The burst problem is becoming more severe as mining depth increases, prompting efforts to relieve high stress areas ahead of mining. Successful stress relief reduces the occurrence of uncontrolled coal bursts. This report by the Bureau of Mines, U.S. Department of the Interior, presents a review of the most widely used methods to detect and destress high stress zones along coal faces. Stress-related burst problems and destressing efforts at a cooperating mine were investigated. Laboratory tests of the drilling yield method for high stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress at various confining pressures. A three- dimensional, multiple-seam computer modeling program, "MULSIM?, was used to evaluate the effectiveness of stress relief methods. Modeling results and guidelines for destressing are presented. Results indicate that dangerously high stress areas can be controlled by either proper planning or destressing. Proper mine planning guidelines and destressing methods such as volley firing, hydraulic fracturing, and auger drilling are discussed.

Jan 1, 1987

By W. K. Collins

Engineered scavenger compounds (ESC's) developed by the U.S. Bureau of Mines are a novel class of compounds that selectively can recover a desired element from a solid or molten alloy. Lithium titanate (L2Ti307 or Li2O?3Ti02) is used as an ESC to recover lithium (Li) from aluminum-lithium (Al-Li) alloys. X-ray diffraction measurements have shown that Li2Ti307 undergoes a phase change during scavenging from an orthorhombic structure to a hexagonal structure. This change is due to the incorporation of lithium in the matrix of the material and the effect of temperature. Although both phases are metastable, the hexagonal phase that forms during the scavenging of lithium from Al-Li alloys appears to be the more stable phase. Recovering lithium from the ESC by electrodeposition does not cause the structure to revert to the orthorhombic phase. The orthorhombic and the hexagonal structures of Li2Ti307 have similar scavenging capacities for lithium. This report proposes a new mechanism for the phase transformation.

Jan 1, 2010

By Charles Camsell

At the Annual General Meeting of the Institute in 1924. I endeavoured to present the position held by the mineral industries in the commercial life of this country. The facts and figures were presented at that time in a detached way. Since then, however, I have made some attempt to analyze them in order to determine the causes for that position and to draw some conclusions as to the future of the mining industry. As everyone knows, our trade figures are very often used in political discussion, especially in discussion of tariff policy. It would be entirely out of order for me to say anything touching the tariff issue and I want to have it clearly understood that, in my opinion, the material I am about to present contains not a single statement or conclusion which anyone would be warranted in using as an argument for either a lower or a higher tariff or for tariff changes of any kind. As a starting point, let me re-state, very sketchily, Canada's general situation in external trade. In the last calendar year, 1924, we sold Canadian merchandise of all kinds to other countries to the value of $1,045,000,000 in round figures. Our purchases abroad reached about $893,000,000. Thus our sales exceeded our purchases by roughly $152,000,000. In other words, we had what is known as a 'favourable balance of trade' - one of the biggest favourable balances we have ever had in our history. The proceeds of our sales of Canadian products enabled us to meet the bills for all our purchases of foreign commodities and, in addition, placed a large surplus to our credit with which to offset our interest charges and other obligations abroad.

Jan 1, 1925

By Qingwei Joshua Ong

Tension piles, also known as uplift or anchor piles, are necessary to resist uplift forces that might cause structural distress. In excavation projects, most uplift forces are developed because of hydrostatic pressures, and so tension piles are subjected to a great deal of tensile forces. Most current methods of design for tension piles completely neglect the tensile strength contribution of concrete, relying only on the steel members to carry the tensile stresses, resulting in an overly conservative design. The stressstrain behavior of the composite material of concrete and steel must be considered for a realistic simulation of tension piles. This paper will examine a case on a tension bored pile in typical soft clay to demonstrate the importance of considering the tension strength and tension softening of the concrete.

Nov 1, 2022

By William L. Fink, Dana W. Smith

In parts I1 and II2 of this series, there were presented results of investigations on the age-hardening of an aluminum-copper and an aluminum-magnesium alloy. It was shown that the simple precipitation theory of hardening3 adequately explained the aging phenomena, including certain so-called "anomalous" behaviors which had caused other investigators to reject or modify the precipitation theory. However, these papers did not discuss the double aging peaks, which have been stressed in recent articles by Dr. M. Cohen4 and Dr. M. L. V. Gayler.6 The present paper is devoted to an explanation of this "anomaly." Fig. 1 is a generalized schematic representation of aging curves at different temperatures. Curve A corresponds to the aging at the lowest temperature, and D at the highest temperature. Certain previous investigators have explained curve A and the initial peaks

Jan 1, 1938

By William L. Fink, Dana W. Smith

In parts I1 and II2 of this series, there were presented results of investigations on the age-hardening of an aluminum-copper and an aluminum-magnesium alloy. It was shown that the simple precipitation theory of hardening3 adequately explained the aging phenomena, including certain so-called "anomalous" behaviors which had caused other investigators to reject or modify the precipitation theory. However, these papers did not discuss the double aging peaks, which have been stressed in recent articles by Dr. M. Cohen4 and Dr. M. L. V. Gayler.6 The present paper is devoted to an explanation of this "anomaly." Fig. 1 is a generalized schematic representation of aging curves at different temperatures. Curve A corresponds to the aging at the lowest temperature, and D at the highest temperature. Certain previous investigators have explained curve A and the initial peaks

Jan 1, 1938

By Ralph C. Flow

In Cleveland County, North Carolina, 1 ½ miles south of Kings Mountain, Foote Mineral Co. operates an open pit for the production of spodumene, feldspar, mica and commercial stone. Spodumene concentrate is sent to Foote Mineral's Sunbright, Va., plant and to other customers. Exton, Pa. and New Johnsonville, Tenn., plants produce lithium com- pounds sold to the oil industry for multipurpose lithium-base greases, to the metal industry as welding flux, to the air conditioning market and to the glass industry. Ceramic-grade spodumene, feldspar, and mica concentrates go to other processing companies from the Kings Mountain plant. Waste amphibolite is delivered to a neighboring quarry operation. Geology and exploration of the deposit have been described by T. L. Kesler, Chief Geologist of Foote Mineral Co., in the September 1961 MINING ENGINEERING. Measured ore reserves as published at that time were 20.7 million tons. The ore deposit consists of a series of lithium-bearing pegmatites enclosed in amphibolite and mica schist wall rocks. The general strike of the pegmatites is northerly, and in the southern part of the pit, they dip slightly towards the west. The largest body being mined has a fairly uniform thickness of about 200 ft. Other pegmatites in the pit area range from 20 to 100 ft in thickness. Minerals in the pegmatites are 20% spodumene, 32% quartz, 6% muscovite, 41 % feldspar and 1 % trace minerals.

Jan 10, 1962

By Jonathan Baggett, Nino Ripepi, Amin Abbasi, Richard Bishop, Juan Monsalve, John Hole

This work focuses on the operational and safety issues associated with karst voids in large opening underground mines. Issues include water inrush, structural instability, and engineering uncertainty in these environments. Coupled with the fracturing prevalent in folded sedimentary rocks, karst voids are complex and challenging ground-control risks. Traditional methods of predicting karst void locations, such as probe drilling, are impeded by the inconsistent spatial distribution and variable sizes of the features as reported by Li et al. (J Rock Mechan Geotech Eng:232–242, 2010) and Hassan et al. (Procedia Chem 19:737–742, 2016). Ground-penetrating radar (GPR) is a geophysical technique that transmits radio waves into a medium and subsequently detects reflected waves via a receiver. The travel time and energy of received signals are then processed and interpreted. The difference in conductivity and dielectric permittivity between limestone and open karst cavities causes strong reflections. GPR is frequently used as a geophysical surveying technique in several industries; however, there is a lack of published research on underground mining GPR applications as reported by Zhao et al. (2015a; Geophys J Int:62–71, 2015b) and Eskelinen and Pellinen (Constr Build Mater:888–898, 2018). The purpose of this work is to demonstrate the use of GPR in an underground stone mine and to discuss the importance of karst void detection ahead of mining.

By George S. Rice

GROUND movement from mining, whether it be for coal, metal, industrial minerals, or .oil, will always present many difficult problems. These are especially serious when valuable surface improvements may be badly damaged. The mine itself, if mining methods are not suitable to the formation, is subject to heavy falls of the main roof in the working places; and with certain structural conditions the movements may cause in coal mines disastrous bumps and outbursts of gas, and in deep metal mines rock bursts. In open-cut work rock and earth slides may result. Absolute prevention of ground movement from mining is impossible unless large pillars are left unmined,

Jan 1, 1937

By James Wonneberg, William Edgerton

"Today’s underground construction megaprojects are tremendous feats of engineering on a massive scale, excavating through ground conditions once thought impossible, using new and innovative contracting practices. But one important truth remains unchanged; projects are built by people. What separates winning projects from the rest? Great people, working in great organizations. In straight-talk fashion this paper sets forth fundamental differences between good project leaders and bad ones, on topics ranging from client relations, design management, and scheduling, to use of the whiteboard, and everything in between. Broadly applicable to all corners of project delivery, this paper will resonate with project leaders from around the world and help identify skills necessary to succeed in the management of underground facilities. A NOTE FROM THE AUTHORS This is a training document, and not really a “paper” per se. We have attempted to tackle some big and potentially complex topics using bite-sized paragraphs, each of which are intended to promote thoughtful introspection and dialog. So please feel free to skip around, or even set this document down while you reflect on your own personal experiences, tactics, and philosophies. We have found that providing examples of “what not to do” is oftentimes more instructive than simply listing “what to do”, hence the Good/Bad format of this document. Please note that “PM” refers loosely to anyone on the project management team not just the “Project Manager”. We also wish to preface this with the following cautionary statements: • The authors do not pretend to be the “Good PM” in all cases. In fact, we’re almost certainly the “Bad PM” for some. We aim to improve on those areas. • It has been said that “The only real training for leadership is leadership.” (Antony Jay) We all started somewhere, and nobody has 20 years of experience on day one. • Converting this text into some sort of prescriptive checklist would be a disservice to the evolution of project management. Our world – and our awareness of it – is constantly changing. We must always be open minded to new ideas and different perspectives on project delivery."

Jan 1, 2016

By Ernest L. Ohie

In 1939 the Geological Society of America published a summary of the geology of the ore deposits of the Mississippi Valley region, This volume, edited by E. S. Bastin, contained contributions from the foremost students of the area which described theregionalgeologic setting of the various deposits as wel as the detailed geology as then known. The various ideas as to the origin of the ores were discussed with the general, though not unanimous, conclusion that the deposits were hydrothermal products, Only those deposits in the immediate Mississippi Valley area were considered without any attempt to introduce evidence from other districts generally accepted as being of the "Mississippi Valley type." Since 1939, much new information has come from extended studies of two of the important districts described in the 1939 report andimportant extensions of the known ore have been found. Likewise, concentrated geologic efforts have been fruitful in severa "Mississippi Valley type" districts - both U. S. andforeign - not treated in the 939 paper. The wealth of new field information on the structural and stratigraphic relations of this interesting ore type, coupled with the results of theoretical and laboratory studies of the past 18 years, makes desirable a review of our present knowledge and interpretation of these important deposits which for many years have yielded over 20 percent of the world's annual production of lead and zinc, together with large amounts of fluorspar and barite. No restatement of the details of the geologic evidence willbe attempted here; the interested student is referred to the papers cited. Slide No. 1 shows the distribution around the world of the deposits under consideration. A principal thesis of my remarks is that there is so much similarity in all these deposits that it seems necessary for all of them to have had a similar mode of origin, whatever that may be. Variations in the shape, size and mineralogy of the orebodies give each district some individuality, but there are enough of the "typical" characteristics present in all cases to make classification in the "Mississippi Valley type" agreeableto most geologists. Thus the overall process giving rise to the ore solutions surely was the same for all in the group. Either they all have igneous affiliations or they all do not. Acknowledgment of this kinship between deposits in the various districts offers many advantages in trying to arrive at a decision as to just what the origin may have been, for the amount of guiding and limiting evidence which must fit into the hypothesis is greatly increased over that available in any one district, To a certain extent this was recognized by the authors of Special Paper 24 in treating all of the immediate Mississippi Valley areas together; by expanding the consideration to include ore deposits of this type all over the world the changes of success, i.e., arriving at the correct answer, are improved several fold. Since most of these districts are quite simple structurally, a number of hypotheses might fit the facts in any one of them, but if the facts to be met can safely be drawn from all the districts, then the explanations which will fit all the data are much less numerous. One purpose of this paper is to call attention to the field facts that have been reported from the .various areas which seem to have an important bearing on the kind of ore fluid that was responsible for the ore and on the way it circulated.

Jan 1, 1958

By William F. Starke

"The Ontario College of Art & Design (OCAD) located in Toronto, Ontario, found itself in dire need of space due to increased enrollment, leading them to embark on a major expansion and redevelopment on campus. The expansion entailed an additional 115,000 sq.ft. (10,700 m2) and a new major structure was required, as well as extensive redevelopment of existing buildings. The new Sharp Centre for Design was designed by acclaimed British Architect Will Alsop, of Alsop Architects, in a joint venture with Toronto-based Robbie/Young + Wright Architects. The OCAD campus is cramped for space and the design selected was a structure built over top of existing structures. The building has been described as resembling a “shoebox in the sky”, supported on raked columns transmitting high lateral forces as well as compression load to the foundations. There are 12 such supports, each supported by an individual caisson. In addition, the project entailed installation of other caissons in the courtyard area with the construction work accomplished under very confined conditions among the existing structures. The remarkable design for the new Ontario College of Arts will surely make it another of Toronto’s architectural landmarks. Several things make this project stand out as a unique deep foundations project.First is the architectural design. Words cannot do it justice: the picture is the only effective way to start to describe it. This is a big two-story box, built over the top of a fragile existing building. The underside of the box is 86 ft (26m) above street level. Students remained still inside the old building while construction was going on around and above them. There were serious concerns about vibration – not only its effects on the academic life; but more significantly, upon the stability and safety of the old building, which rests somewhat shakily on shallow spread footings.Steel stilts that look like toothpicks when scaled against the new and existing structures support the box. The stilts are much sturdier than they appear from the pictures, but it is easy to visualize the complexity of the loads they transfer to the foundations below."

Jan 1, 2004

By G. M. BUTLER

TWENTY-ONE of the states in the Union, the Territory of Hawaii, and seven provinces of Canada now have in operation laws requiring that professional engineers be registered or licensed. In addition, two states require that civil engineers be registered, and one other state demands registration of structural engineers. Moreover, nearly every year sees additions made to the list. The registration movement, fostered by the American Association of Engineers, now has the powerful, energetic backing of the An1,erican Society of Civil Engineers, which is itself now fostering registration legislation, and there is a strong sentiment in favor of registration in the American Institute of Electrical Engineers and the American Society of Mechanical Engineers. Only in the American Institute of Mining and Metallurgical Engineers is anti-registration sentiment, strongly dominant, but many members of this organization are enthusiastic advocates of registration.

Jan 1, 1930

By George H. K. Schenck

The North American-based mining engineer needs to understand the differences that exist between mechanical mining or boring machines built on this continent and those built in Europe. The differences Ere most clearly seen when machines for large-sized openings--about 15 feet high-are considered. This report will focus on the innovations of European origin. The rock-breaking tool, drag bit, or roller cone that is efficient for a particular project is related directly to the strength of the rock involved. This strength is generally stated in reference to the rock's unconfined compressivee strength in pounds per square inch (psi) although it is well recognized that a rock's shear strength is also important. Compressive strength has been adopted because it is simple to test for and provides a convenient comparison. Table 1 relates cutter type to compressive strength and indicates the general nature of the machine innovation devel¬oped in Europe.

Jan 1, 1970

By Thierry Bernard, Philippe Dozohne

May 13th, in the back country of Nice @arice) collapsed a complete piece of mountain, cutting the RN 2085 and destroying a part of Valabfre’s viaduct. The fist inspections of the site showed that materials had broken loose from surrounding cliffs, The geologists discovered that a block of several thousands of m3 remained suspended in cliff and that it presented a risk raised of gliding. Decision to destroy it by blasting in one blast was there taken by the French department’s council of the Maritime Alps. A race against the clock engaged. Indeed, the RN on 2085 is the main axis connecting the village of Saint Etienne de Tinee and the resort station of ISOLA in the centre of Nice

Jan 1, 2001