Search Documents

By D. T. Couillard

Video technology is becoming an important tool for many designers of industrial training programs. This report describes how trainers at the Minntac Mine, Mt. Iron, MN, have developed videocassettes of safe job procedures (SJP's) for training miners assigned to perform unfamiliar work tasks. All steps necessary for videocassette production, from idea to finished product, as well as the required equipment and prices, are listed and/or briefly explained. Minntac officials believe that the SJP videocassettes have contributed significantly to a reduction in mine accidents.

Jan 1, 1985

By Malcolm Black

Introduction The circumstances under which the gold mining industry was forced to curtail operations a few years ago are well known to all. The effect of those circumstances is particularly noticeable when one enters some of the larger mills that were designed, in better times, to treat relatively large tonnages. On their grinding floors one will observe that a number of grinding units are lying idle, and the ravages of rust are everywhere in evidence. The same applies to other equipment throughout these mills. In 1941, we found it necessary to reduce tonnage considerably in the Wright-Hargreaves mill. With the assumption that a lower tonnage would be of long duration, we began to focus our attention on some of the idle equipment with a view to re-arrangement of the flow-sheet for greater economy of operation. In an article by the writer published in the Engineering and Mining Journal (March, April, and May issues, 1939) , it was pointed out that in designing this mill there was a very limited floor space available. The choice of thickening equipment was imposed solely by the necessity for space: conservation. Thickening by gravity would have required 5,000 square feet of floor space, whereas Genter thickeners required only 1,200 square feet. As a consequence, the Genters were chosen. The decision to add flotation to the circuit was made primarily to save space. On a cost-plus-tail basis, 80 to 100 hours agitation on all pulp would produce similar overall results, but would require much more space.

Jan 1, 1948

By P Wahyono, H Vega, S Riza, P Vergara, P Gonzalez-Carbonell

PT Freeport Indonesia (PTFI), operating in the Ertsberg Mining District in the Province of Papua, is developing the Grasberg Block Cave copper-gold mine. The site aims to output 160 000 t/d and will be located underneath the current Grasberg Open Pit. Initial studies of the potential to develop a block cave mine in the Grasberg orebody have revealed that the mine will require significant volumes of air. The Grasberg Block Cave (GBC) project requires four primary fans (3750 kW each) to support production at full capacity.Fan #1 commissioning was accomplished successfully on 9 February 2012. However, Fan #2 chamber, which is separated by a 20 m pillar, had not been completed. The main challenge was Fan #2 chamber still needed to be benched. The risk of damage to the critical infrastructure in Fan #1 chamber, including ground support, cracks in pedestals, and misalignment in the impeller shaft were considered. The challenges were blasting the bench without damaging the surrounding infrastructure, completing the work safely and meeting the schedule. This was achieved with the engineering control methodology. This paper summarises the benching process of Fan #2 chamber and its impact upon Fan #1.CITATION:Vega, H, Riza, S, Gonzalez-Carbonell, P, Wahyono, P and Vergara, P, 2013. Excavating an underground primary fan chamber that is adjacent to a fully operational primary fan in PT Freeport Indonesia's Grasberg Block Cave Mine, in Proceedings The Australian Mine Ventilation Conference , pp 115-122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Douglas A. Anderson

The US Bureau of Mines, in RI 8507, has shown that blast vibrations at low frequency are more likely to cause damage and complaints than those at higher frequency. Since that publication in 1980, the Office of Surface Mining and many state and local regulatory authorities have incorporated frequency in their regulations for acceptable ground vibration from blasting. Even when frequency is not explicitly stated in regulations, it may become an issue in hearings or in court.

Jan 1, 1992

By FRANK RIEBERS

IN DISCUSSING the selection of a geophysical method, much of what the writer will say is applicable to any of the various methods and to their use in prospecting, whether for oil or for other minerals. Specifically, the writer's subject is the problem, particularly pressing on the Pacific Coast, of checking the rising cost of the discovery of new fields by the proper employment of geophysical methods. Table I was prepared from statistics published by the California State Milling Bureau. The writer selected five of the largest a:ld most active companies operating in California, segregated the number of wild-

Jan 1, 1930

This three-part report provides the results of an industrial engineering study that assessed the safety and efficiency of underground ore handling in U.S. metal mines. One of the primary findings of the study was the improvement needed in controlling muck size in the are handling stream. Oversize ore is causing much additional labor, creating work stoppages, and is a principal cause of accidents in metal mines. The specific objectives of the Present Systems Study were to determine and evaluate the productivity of existing ore handling systems in a representative group of underground metal mines, to relate the available historical accident record statistics of these selected mines to the specific operations in the overall ore handling operations, and to highlight the potential areas of improvement for each mine on the basis of productivity and associated hazardous index for each operation.

Jan 1, 1974

By E. A. Sobering

Hydraulic filling or sand filling is a system used to fill underground excavations with a dense pulp. Milltailings are commonly used. The resultant fill, after being placed and de-watered, is known as hydraulic fill. These fills have been effectively used to (a) provide immediate support of the workings place during stoping; (b) .facilitate the recovery of pillars; (c) limit surface damage by subsidence; (d) permit the mining of parallel hanging-wall orebodies; (e) stabilize the ground in mines, thereby reducing the rock burst hazard; (f) control and prevent mine fires; and (g) solve tailings disposal .problems. The various uses of hydraulic filling have been developed during the last ninety years. In 1864 it was employed only to control surface subsidence. Since then, this system has been successfully applied to meet specific ground support problems. Methods of handling mine-fill derived from a source outside the stope include transportation ?Of the material by hand, mechanical, pneumatic, and hydraulic means, or a combination of these methods. The hydraulic method has many advantages not found in the others; a significant advantage is the low compressibility of the material when compared to other mine-fill material. The hydraulic filling operation includes the .preparation and transportation of the pulp. The underground practices in .placing the fill vary from mine to mine. The chief reason, formerly, for using hydraulic fill was the exceptional support it provided, but recently it has proven an important means of reducing mining costs. This is especially true where labour is a large part of an alternative method, or where timber consumption is greatly reduced. The indirect benefits of hydraulic filling are probably as important as the direct benefits, and few important disadvantages exist.

Jan 1, 1956

By J. Tumialán

El presente trabajo realiza un estudio comparativo de las propiedades físicas y químicas de tres nitratos de amonio, cuya interpretación se relaciona con las conclusiones sobre estudios de AN-FO realizados en la Universidad de Missuri. Básicamente se evalúa los factores de campo que afectan la performance del AN-FO, como el confinamiento, diámetro del hueco, inicio de la carga y mezcla del explosivo, así como se mide la factibilidad de disparar al AN-FO sin una dinamita. Los tajeos de producción de la mina Casapalca sirvieron de ejemplo para ejecutar dichos disparos, encontrándose que el AN-FO francés es el más adecuado y sensible en torno a la performance de los otros explosivos, dado sus componentes como su ahorro de consumo.

Nov 20, 1972

By J. A. Marts

Reservoir properties including porosity and permeability distributions in longwall coal mine gobs have direct application to modeling the flow patterns and gas distributions in the gobs. Proper assessment of these distributions is required to assess gob gas hazards such as spontaneous combustion and explosive methane mixtures and to optimize gob gas venthole operation and nitrogen inertization. Determining the reservoir properties is difficult given that the gob is inaccessible and direct measurements cannot be easily taken. Several techniques had been used by previous researchers and will be discussed. This paper will present the methodology used to model the gob compaction by simulating the sequential extraction of coal. Two Western US coal mines were used for case studies. By determining volumetric strain, the porosity and permeability distributions in the gob can be calculated. The geo-mechanical model predicts an axisymmetric volumetric strain distribution with a steeper slope near the start-up room and a shallower slope near the active face.

By Robert T. Gdagher, Allison Butts

EDUCATIONAL trends as reflected in curricular changes are of interest and importance in engineering educa¬tion both as matters of record and as considerations for the future. The data on which the evidence of this report is based were obtained by sending questionnaires to all schools in the United States granting the undergraduate degree in mining engineering, metallurgy, or metallurgical engineering. The questionnaire had two parts, one inquiring as to the general nature of revisions made or planned, and the other asking for information on specific courses added to or dropped from the curriculum, or given more or less time than formerly. The frequency with which curricular changes are made, even in normal times, is notable. Although it was expected that the period since 1939-40 would show numerous revisions, it was somewhat surprising to find that of 62 mining or metallurgical curricula in existence in 1939-40 and reported in the present survey, 58 had been revised or are shortly to be revised, 52 having already been changed during this period. Moreover, approximately half of the mining schools that have already revised their curricula, and probably a similar proportion of the metallurgical schools, are about to make further important changes.

Jan 1, 1948

By D. W. Fuerstenau

On page 1243, column 1, the first line of the author's reply should read "D. W. Fuerstenau (author's reply)---," rather than D. E., as printed. In the sentence immediately preceding the first equation (page 1243, column 2)' the word "none" was omitted. The sentence should read: "However, if enough ore is put into the mill [so] that none of the energy put into the mill is wasted on metal-to-metal impact, then the product should have size modulus determined by the relation: ..."

Jan 1, 1961

By George E. Fish

This report describes investigations conducted by the Bureau of Mines from 1957 through 1959 in the Roseland anorthosite-titanium belt of Nelson and Amherst Counties, Va., for the purpose of studying the titanium resources of the area. Three titanium deposits containing much saprolite ore derived from the decomposition of anorthosite and diorite were selected for detailed study Following a reconnaissance of the reported titanium occurrences in the belt. These three deposits occur in or are associated with anorthosite. Most of the occurrences are situated on or near the contact between the anorthosite and the gneissic country rock. The saprolite deposits are as much as 1.5 miles long, 1,000 feet wide, and 100 teat deep and contain significant reserves of titanium-bearing material estimated in excess of 20 million tons. Where it was penetrated by drilling, the unweathered rock beneath the saprolite contains nearly the same titanium values as the saprolite.

Jan 1, 1962

"Status of the Mineral Industries" provides a written and graphic view of the Nation's mineral position and its mineral industries. The report, issued annually by the Bureau of Mines, U.S. Department of the Interior, describes recent activities in mineral production, consumption, imports, exports, and uses of significant minerals and mineral raw materials. Charts profile trends for the past 28 years in supplies and uses of iron, steel, major nonferrous metals, primary nonmetallic construction raw materials, fertilizers, and plastics. Also included are current and historical financial data on the mineral industries, such as debt-equity ratios, asset-to-liability ratios, and plant and equipment expenditures.

Jan 1, 1979

By Anthony M. Bauer

It is the nature of mining to reshape the landscape. Mining is an earth moving process with many of the same activities associated with the regrading of a site for a shopping center, drainage channel, housing project or ballfield. The difference exists only in purpose and duration of activity. The purpose of mining is to, produce a valuable product. The purpose of regrading for construction of a project is to create a predetermined landscape for a specific end use. In both situations the objective is to move earth materials as efficiently as possible. The question is then raised, if similarities exist, can mining operations be directed to shape predetermined landscapes as an integral part of its earth moving activity. This paper will explore the opportunities and issues of shaping sand, gravel and hardrock construction aggregate sites for productive end uses. It is based upon the premise that, as an earth moving operation, the process of extracting sand and gravel includes an inherent capability to shape productive lands as an integral part of the mining operation. In the course of any mining operation non-commercial materials, including overburden, fines and excess sand are handled to extract and process the commercial products. This activity exists regardless of whether or not there is a plan to reclaim the land. Moving this dirt is a basic operational cost. This cost need not be significantly increased when the material is deposited to shape land rather than be stock- piled just to clear the way for mining the deposit. Moving of dirt to create useable land can be guided by the same criteria used to remove the dirt from the deposit: for example, limiting the- hauling distance. Over a period of time earth handling costs can be reduced by minimizing the need to transport the stockpiled material a second time to the new landform location.

Jan 1, 1984

By V. A. Ettel

Current practices in electrolytic winning and refining of copper , nickel and zinc are reviewed from the point of view of their respective energy requirements. The electrical energy requirements of these processes are broken down in to the individual components, which belong to two basic categories: (a) thermodynamic energy requirements (G of the desired reaction) : (b) energy losses (anode and cathode polarizations, ohmic drops in the electrolyte and in the cell hardware, energy losses due to unwanted side reactions and electrical shorts). The individual energy components are separately examined for each electrolytic process and the potential for energy saving in these processes is discussed. It is shown that many potential energy-saving measures are uneconomical at the present time, as they increase over-all operating costs. The discussion is focused on those approaches which hold most promise for the future.

Jan 1, 1977

By Philippe Angers

This article analyzes the social acceptability process of a mining project located in an existing city. It will explore how the principles of sustainable development have been integrated in the project of the Canadian Malartic open pit mine held by the Osisko Mining Corporation, and the corporate social responsibility (CSR) initiatives proposed to strengthen the social acceptability of the project. This mine is located on the ancient south quarter of Malartic and has required the displacement of hundred of houses and five institutions. The location and the inherent social impacts generated by the relocation of the citizens of the south quarter makes this case particularly interesting to understand social dynamics in an era of environmental consciousness. These major constraints of the mine generate high expectations within the urban population with regard to the social and economic benefits it will receive from the project. In a context where society demands higher CSR from the corporation, Osisko is closely followed regarding their actions toward the sustainable development principles to see if they respect the environment and the desires of the community. From the beginning, the company had to be a model of sustainable development in various aspects reflected by the manifold interest of the population. To understand the endeavor made by the company to fulfill the demand of CSR, we will analyze how the company understood sustainable development principles and what CSR initiatives Osisko company put forward. We will explore the involvement of the company in various social aspects like employment, employee satisfaction, and the level of commitment to non-discrimination policy in employment, notably with the native populations. We will also take a closer look at the relationship built by the company with the community and the level of commitment with the various stakeholders of the community. In this way, we will be able to seize the level of involvement of the company in the fulfillment of the principles of sustainable development toward a higher CSR, and to specify the trajectory adopted to build social acceptance.

Aug 1, 2013

By R. L. Cosgriff

A commercial, battery-powered mine vehicle has been equipped for remote operation in coal mines. This vehicle is controlled by an operator from the remote station. Command signals originating at the remote station as well as video and data signals originating on board the vehicle are relayed between the remote station and vehicle using a single coaxial line. This coaxial line is normally 2,000 feet in length and is reeled in and out from a drum mounted aboard the vehicle The vehicle has a maximum speed of 6 ft/sec and a minimum speed of 4 ft/sec using 36-volt excitation of the traction motor. If this traction motor is excited by two of the three batteries, 24-volt excitation, the vehicle will travel at approximately 2 ft/sec. The speed can be reduced by the operator to 1 ft/sec. This vehicular system has been tested in coal mines. Presently, the major limitation of this system is associated with fatigue failure of the splices in the coaxial line and lack of mobility caused by its 3-wheel design.

Jan 1, 1974

By William Gleason

While a fleet of 100 t (110 st) haul trucks were busy removing overburden from the open pit mine in the distance, a host of dignitaries, including congressmen and California state representatives, gathered for Molycorp?s official groundbreaking ceremony at the Mountain Pass Mine on April 20. The mine, recognized as arguably one of the richest rare earths deposits in the world, is at the center of Molycorps? strategic ?Mine to Magnets? plan. It aims to secure America?s future supply of rare-earth-dependent technologies by developing a strong domestic rare earth industry. Molycorp identifies rare-earth-dependent technologies as those that cannot be produced without rare earth materials. The list of these technologies is long and growing. It encompasses everything from personal electronics and batteries for hybrid cars to permanent magnet generator wind turbines and national defense applications.

Jan 1, 2011

By Noel N. Moebs

The coal wants at the Westland Mine in southwestern Pennsylvania consist chiefly of elongated, sandstone-filled channels with slickensided basal contacts. Tentatively identified as washouts, these channels are about 1,000 feet long and 300 feet wide, are erratic in occurrence and trend, and are difficult to delineate from the customary core drilling pattern. Roof conditions are hazardous adjacent to the washout contact, but roof stability is generally unaffected greater than 30 feet away.

Jan 1, 1981

This Bureau of Mines report is devoted to descriptions of systems that provide in-mine wired telephone service. Although they may incorporate other features, each system described functions to allow one telephone to selectively access another telephone. Except for the paper on Conventional Telephone Equipment, the equipment described is newly developed and specifically designed to satisfy the requirements of underground mine communications.

Jan 1, 1977