Search Documents

By E. J. Kloos, R. H. Schutz, B. I. Ferber

To Assist users in the selection of reliable and satisfactory respiratory protective devices, the Bureau of Mines has established five schedules of minimum performance requirements for the approval of respirators . The current revisions of these schedules include 13D for self-contained breathing apparatus, 14F for gas masks , 19B and the amendments to 19B for suppliedair respirators , 21B for dust , fume, and mist respirators , and 23B for chemical cartridge respirators . Copies of these schedules may be obtained from the Bureau of Mines, Publications Distribution Section, 4800 Forbes Avenue, Pittsburgh , Pa . , 15213 . Approval tests on respirators are performed only at the request of the manufacturer of the respirator and at his expense. If the device meets the approval requirements , a certificate of approval is granted on the complete respirator. This certificate states that as long as the respirator is manufactured as originally approved, or in accordance with any changes covered by an extension of the original approval, the manufacturer may advertise and sell his respirator as being approved by the Bureau of Mines. Many industries and regulatory agencies require that respirators approved by the Bureau of Mines be used where respiratory protection is needed. The Bureau of Mines, however, has no regulatory power over the use of the respirators that it approves. It acts as an impartial testing agency to insure the availability of suitable and safe respirators. At frequent intervals, the Bureau of Mines purchases approved respirators and replacement parts on the open market. These are examined for conformity to the approved status, and are checked to insure that the manufacturer's production facilities are maintaining a satisfactory quality control .

Jan 1, 1966

By Parameswaran V. S, Anshuman Singh

This is a case study on ground improvement using Stone columns at Kokrajhar in Assam which comes under seismic Zone V as per IS: 1893. The strata at site comprised of mostly fine sands with low SPTN values, fine content less than 10% and ground water table (GWT) at shallow depth. As ground water table subjected to seasonal variation, water table is considered at ground level for designing purpose. The geotechnical profile of the boreholes was analysed on the guidelines of IS 1893 (Part 1) -2016 and it was observed that the liquefaction potential of the soil layers is prominent and ground improvement is inevitable up to a depth of 9.5 m below existing ground level. In order to mitigate the liquefaction of soil layer, Stone columns were proposed. The in-situ soil is densified using wet top feed vibroreplacement method with an area replacement ratio of 16%, so that the relative density of the soil can be enhanced to prevent liquefaction risk. Correlation between relative density, fines content and increment of SPT N –value given by Tokimatsu and Yoshimi (1983) was used for designing purpose. Field tests such as SPTs were carried out at site to validate the extent of SPT (N) improvement. Detail comparison of pre and post density, SPT N values and CRR values were discussed in this paper.

Nov 1, 2022

Jan 1, 1959

By G. J. Heferen, A. Pranowo, N. J. Aslin, P. O. Eriksson

Glencore Technology (GT) has over four decades experience supplying stainless steel cathode plates (“cathode plates”) to the electro-refining and electro-winning industry. Cathode plates are typically the single biggest capital investment in a refinery. Refineries may view cathode plates as fixed asset or consumables depending on their operational characteristics. This paper examines the issue of cathode plate life and the strategies and philosophies used by different plants in the management of their cathode plate asset. Some plants operate with their original plates after more than 20 years. Others accept high turnover and regular maintenance as normal operating practice. Reference data are provided on plate life for various operating plants including benchmark plants achieving best-practice plate life and operating cost. The role of the electrode handling equipment on cathode plate longevity is also examined, including latest developments in Cathode Stripping Machine, robotic copper stripping, and full-automation production cranes. The ability to identify and manage the population of plates in service is also critical for maximising plate life and minimising its overall operating cost. This paper discusses a novel and unique RFID system for tracking and managing cathode plate inventory. INTRODUCTION Permanent cathode plates The adoption of permanent stainless steel cathode electrodes in the electro-refining of copper was the most significant process development since the first commercial electro-refineries were built in the late 19th century. It provided significant improvement over the labour intensive and complicated starter sheet system. Copper grows over the permanent cathode blade for a number of days before being stripped, and the permanent cathode can be returned straight back to cells for the next cathode cycle. Glencore Technology (formerly Mount Isa Mines (MIM), then Xstrata Technology) has been manufacturing permanent stainless steel cathode plates from the late 1970s with the birth of ISA PROCESS™, and the Kidd process that came one decade later. Invented and commercialised by Mount Isa Mines, the ISA PROCESS™ was first implemented into Copper Refineries Limited (CRL), Townsville, in 1978. The KIDD PROCESS by Falconbridge evolved in the 1980s and was first implemented into the Kidd Creek Tankhouse, both operations converting from traditional copper starter sheets.

Jan 1, 2019

By A. B. Hooker

Many attempts have been made to develop methane detectors that will be safer and more accurate than the flame safety lamps used to detect methane in mines. The development has taken two general forms, namely: (1) Methane detectors, in which the evidence of methane depends entirely upon changes in the appearance of the detecting element, such as a flame or filament; (2) indicating methane detectors or those equipped with scales upon which the approximate percentage is definitely indicated. As an aid in the development of suitable detectors, the United States Bureau of Mines has assembled and published in its Schedule 8B a set of minimum requirements which tests and experience have shown desirable for methane detectors. Any manufacturer may submit his detector for inspection and tests leading to approval under this schedule.

Jan 1, 1930

By D. G. Almond

Nkomati Nickel Mine in South Africa processes one of the world?s hardest ores in a 375k TPM autogenous grinding circuit. The plant employs an unconventional processing circuit, comprising a primary autogenous mill (AG or FAG) and pebble crushing circuit followed by a secondary hybrid pebble/ball mill and classification cyclone cluster. Advanced Process Control (APC) or Expert Control is now generally accepted as an advantage in most modern high capacity concentrator grinding circuits. This paper reviews the installation of model predictive control at Nkomati and examines the results and benefits of installation in an autogenous mill during plant ramp-up. The paper also demonstrates how predefining process control objectives together with good plant and supplier cooperation can achieve a robust and reliable APC implementation on a very short site program. The results conclusively demonstrate operational and economic benefits during circuit operation with the advanced process control system ON. Production performance and circuit stability were significantly better than during manual control.

Jan 1, 2012

By H. H. Schrenk

One phase of Bureau of Mines work in health and safety is promotion of the use of safe, satisfactory, and reliable respiratory protective devices. To insure that such devices will be. available, the Bureau has established schedules of minimum requirements for oxygen breathing apparatus,3/ gas masks,/ supplied-air respirators (hose masks, air-line, respirators, and abrasive blasting helmets, hoods, or masks),5/ and dispersoid (dust, fume, and mist)

Jan 1, 1943

By L. F. Willmott

The Bureau of Nines at Morgantown, W. Va., has been investigating, on a pilot plant scale, various methods of gasifying bituminous coal with oxygen and superheated steam to produce synthesis gas, as part of the broader program of finding new uses for coal. Differences in the pressure gasification methods used have depended on differences in the manner in which the pulverized coal is fed to the gasifier. One of the methods of feeding the coal that was investigated was the continuous, integrated coal-water slurry system. Goal and water were first mixed to produce a slurry; then the slurry was pumped through a heated coil. to evaporate the water fraction; the resulting steam was superheated, and some of it was separated so as to adjust the ratio of the residual steam to the coal fraction and make the resulting mixture suitable for partial combustion with oxygen in a pressure gasifier. Both before and during this reported3 developmental work it was necessary to make an extensive literature search into the technology of aqueous slurries in order to establish design criteria for the pilot plant and to correlate results of various phases of the work with that of other investigators, The pilot work coincided with the commercial development of a long-distance pipe- line for the transportation of coal as a coal-water slurry, and this fact tended to broaden the scope of the pilot plant work and the extent of the literature search. This bibliography is the compilation of the material that was collected.

Jan 1, 1963

By John G. Kelly

"In 1982 an extensive study was carried out to determine the best means of size reduction for the ore to be hoisted through the borehole hoisting system at Sherritt Gordon's Fox Mine.The study examined three alternatives:1. a jaw crusher,2. pneumatic rockbreaker(s) at a grizzly, and3. hydraulic rockbreaker(s) at a grizzly.The final decision was a compromise between alternatives 2 and 3. Two rockbreakers, one pneumatic and one hydraulic, were installed over a single grizzly. Some modifications have been made to the system, but over-all it has operated at acceptable levels since its installation in July 1983.As all the ore passes through a jaw crusher before being hoisted to surface, an evaluation of the relative performance and cost-effectiveness of the jaw crusher and the two types of rockbreakers is possible. This paper outlines the initial study, and compares the three breaking systems in operation at Fox Mine.IntroductionThe Fox Mine of Sherritt Gordon Mines Ltd. is located 800 kilometres north of Winnipeg near Lynn Lake in Northern Manitoba. Production at the copper-zinc orebody began in 1970 at a rate of 3,000 tons per day. Over 12.5 million tons will have been hoisted from the underground mine when the ore reserves are depleted in October 1985.The mining method at Fox Mine is sub-level open stoping with delayed backfilling are from the upper level stopes, above the 2000 level, is mucked on the main levels established at 400-ft elevation intervals, and is fed through a central orepass to the crusher located on 2100 level. Production in the lower levels commenced in 1975, and ore from the 2200 and 2400 level stopes was hauled up a 15010 ramp by 26-ton trucks to the 2000 level orepass dump. Projected production rates from the 2600 and 2800 levels using the trucking system were too low, and therefore, in 1983 a borehole hoisting system was commissioned to hoist that ore'!'. One thousand tons per day of ore are skipped through an 8-ft diameter borehole from the 2650 level loading pocket and dumped on the 2000 level. The ore is transferred by LHD to the main orepass for crushing before being conveyed to the main shaft for hoisting to surface (Fig. 1)."

Jan 1, 1986

By Paul Guliov

Potash dominates the industrial mineral scene in Saskatchewan accounting for 44% of total provincial mineral production in 1981. More than 7 million tonnes of potash have been produced annualy in recent years; ten underground mines are presently (1983) active. Sodium sulphate and cement are also important mineral products. Construction aggregates, clay products, bentonite, salt, peat moss and sulphur complete the list of industrial mineral products.

Jan 1, 1984

By W. Hermülheim, J. Brune

"This paper analyzes mine emergency management and rescue practices in German underground coal mines and compares them to those used in the United States. The German mining industry has developed these practices over more than 100 years, and they have successfully managed numerous fire, water inundation and ground control emergencies using these techniques. The authors interviewed German mine emergency professionals about rescue team and emergency operations. These operations were then analyzed to determine which of these German principles would be of interest to United States mine rescue teams. Implementing these programs into United States mine rescue and emergency operations was analyzed. INTRODUCTION Coal mining has become much safer industry than it has been in the past. Advances in safety and health regulations and company polices have improved working conditions for miners all over the world. Even with these advances there is still a need for continued attention to safety and health. It is also important for mine safety professionals to observe practices and procedures in other countries and cultures and learn what and how to apply this knowledge in their own systems. Coal mine rescue has been an integral part in improving coal mine safety. Mine rescue procedures have evolved with time, experience and technology development. Today, coal mine rescue teams are still needed and must be continually trained and prepared for any mine emergency. Although it is hoped that improved mine safety policies and practices will eliminate coal mine disasters in the future, accidents remind us that disasters can still happen today. In May 2014, Turkey experienced a severe coal mine disaster where 301 people were killed [G.Tuysuz, 2014]. Our industry must learn from these incidents, focusing on disaster prevention and making improvements in mine rescue operations. Mine rescue procedures differ from country to country due different regulatory environments and different historical evolution of emergency response. Sharing practices and procedures from one country to another enables learning from different experiences and cultural backgrounds. Sharing is also a way of preserving information, identifying and learning best practices."

Jan 1, 2015

By Oliver Bowles

"Asbestos" is not the name of a distinct mineral species but is rather a commercial term applied to fibrous varieties of several minerals. The origin and significance of names applied to asbestos by early writers are discussed in the section devoted to sources of supply and terms employed in ancient times. VARIETIES The most useful variety of asbestos is chrysotile, a fibrous serpentine the composition of which is expressed by the formula H4Mg3Si209. Chrysotile is characterized by a strength and flexibility that permit the use of the longer fibers for spinning. The bulk of the world production of both long and short fibers, is of this variety.

Jan 1, 1935

By Forrest T. Moyer

To keep the mineral and allied industries informed of trends in the causes of accidents and to point, out the need for corrective measures, the Bureau of Mines collects, analyzes, and periodically publishes health and safety statistics. This report includes data for 1962 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following: General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1964

By Forrest T. Moyer

To keep the mineral and allied industries informed of trends in the causes of accidents and to point out the need for corrective measures, the Bureau of Mines collects, analyzes, and periodically publishes health and safety statistics. This report includes data for 1962 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following: General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1964

By L Dyer, A Keith, G D. Corder

As mining activity moves to remote and less developed locations globally, a holistic approach to mine development is fundamental for achieving a balance between strong financial returns and corporate social responsibility and transparency. Key inter-related fundamentals such as social licence to operate, life-of-mine operational planning, minimising environmental impacts and, most importantly, attractive investment returns for the mining company all contribute to the viability of any new mining project.However, the typical practice in the mining industry is often to treat environmental and social/community aspects as separate compliance issues that are dealt with at minimum cost and disruption to the project and resulting operation. This often results in less than optimum environmental and social outcomes, and presents considerable liabilities at the time of closure when rehabilitation programs continue to require funding when all revenue has ceased.The five capitals model seeks to identify each of the key contributors to sustainable development as financial, manufactured/physical, social, human and natural to formulate a type of triple bottom line approach balancing these often competing project factors. The SUSOP® sustainability risks and opportunities framework, developed by the mining industry, bases its approach on the five capitals model and proposes an approach that breaks down enterprise silos to identify innovative solutions for life-of-mine sustainability. This framework has been developed with the nature of mining projects in mind in order to produce approaches and outcomes relevant throughout the life cycle from the planning phases, through project design and construction into operation and closure.This paper argues the need for a more holistic approach to the development and operation of mining projects, and presents case studies where a holistic approach has been applied, in whole or part, and discusses the lessons learned from these case studies.CITATION:Corder, G D, Keith, A and Dyer, L, 2014. A capitals based approach – leading innovation in planning for life-of-mine sustainability, in Proceedings Life-of-Mine 2014, pp 499–512 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By E. W. Dean

This report on the physical and chemical properties of typical crude oils of Oklahoma is the sixth in a series of preliminary chapters of a bulletin covering the producing districts of the United. States. Preceding reports* may be obtained on request. The details of the methods used in this survey in collecting samples, making laboratory tests, and interpreting results are discussed in the first three papers. If any errors or omissions are noted by readers, it is hoped they will be brought to the attention of the Bureau of Mines for correction before the appearance of the permanent report. Samples of Oklahoma crudes analyzed in this report were taken from those fields representing the major production of the State. The Oklahoma Geological Survey designates 172 different oil and gas fields in the State, S1 being in Osage County, 14 in Tulsa County, 14 in Okmulgee County, 9 in Washington County. The list of samples collected by the Bureau of Mines represents only 5 fields in Osage County - Bigheart, Burbank, Hominy, Osage Junction, and Pershing - yet these samples, together with those from adjoining fields, are representative of nearly all crude produced in the county. The sample 'from the Pershing field, for example, is representative of the crude produced in several fields in that part of the county - such as Nelagoney, Pawhuska, Wyomona - and the sample from the Skiatook,

Jan 1, 1922

By L. Allan White

Instrumental analysis is an indispensable tool to many phases of research on rare-earth metals and their compounds; therefore, the development of new and improved instrumental techniques is essential. This report describes an emission spectrometric analytical method using direct-current carbon-arc excitation of various rare-earth-oxide mixtures. Lanthanum oxide serves the dual purpose of an internal standard and a constant major constituent. The versatility of the method was demonstrated by three different applications: (a) Analysis of complex rare-earth concentrates; (b) determination of impurities in high-purity rare-earth oxides; and (c) detection of rare-earth elements in other types of matrices, such as those resulting from beneficiation of rare-earth ores. The average error of analysis in the concentration range of 0.2 to 10.0 percent was 14.6 percent for a group of complex synthetic mixtures of rare-earth oxides. An average error of analysis in the concentration range of 0.05 to 0.50 percent was 21 percent for a group of high-purity rare-earth oxides.

Jan 1, 1959

By S. B. Christy

This report on the electrodeposition of gold and silver from cyanide solutions represents work that has occupied my time at intervals during the past 20 years. The investigation has been carried on simultaneously with my duties as professor of mining and metallurgy of the University of California. During shis long investigation I have been assisted in the details of the work by, a number of my former students, acting in turn as assistants. Particular mention in this connection is due W. H. Hilton, who graduated in 1900; C. T. Dozier, 1902; N. C. Stines, 1905; H. N. Herrick, 1907, and L. C. Uren, 1911. It is impossible to publish full details of the many thousands of experiments performed. Effort has been made to present only the essential data. Wherever possible, the results of the experiments have been expressed in diagrammatic form by curves showing the relation between the simultaneous variables of the experiments. It is necessary to show, as nearly as may be, the state of the art. This is difficult because of the meager literature on electrodeposition in the cyanide process; hence resort must be had to the specifications and claims of patents, most of which seem never to have been applied on a working scale. Such information consequently can not be taken at its face value. Expressing the essential ideas evolved in such specifications is no easy task. Clearly, in quoting from patent records it is not ·feasible to enumerate all of the specifications or the claims allowed the inventors. A statement of the chief contributions to the art in the patent cited must suffice. Legal details, of course, must be obtained from the original patent. In the study of patent literature, when one compares the ardent hopes of the inventors with the results realized from their efforts, it becomes clear that in the development of an art no one man contributes everything. Each subsequent inventor stands on the shoulders of the one who has gone before. It is only through the summation of the contributions of many inventors that the art as a whole prospers. On October 19, 1887, a British patent was granted to McArthur and Forrest for the use of dilute cyanide solutions for treating gold and silver ores. The rapid extension of this process, in various forms, all over the world, has almost revolutionized the treatment of ores containing precious metals. It is a remarkable fact, however, that long before this patent was granted there was issued, on February 5, 1867, to J. H. Rae, U. S. patent 61866, for an electrocyanide process. Thus a method of electrodeposition from cyanide solutions used for treating ores was invented 20 years before the McArthur and Forrest patent .was granted, although the process did not come into general use. On May 24, 1889, U. S. patent 403202 was granted to McArthur and Forrest for the use of zinc shavings for removing gold and silver from cyanide solutions. The use of finely divided zinc is still the standard method for recovering 'gold and silver from cyanide solutions. Since this patent was granted, many attempts have been made to replace the precipitation upon the zinc by methods of electrodeposition. It is the purpose of this report to give an outline of some of these methods, as well as to show the relative advantages and disadvantages of the zinc and the electrical methods of recovering gold and silver from cyanide solutions.

Jan 1, 1919

By R. L. Wiegel

Some of the mineral deposits that are being processed today, and especially those expected to be processed in the future, have relatively low compositions of the valuable mineral. With these low-grade ores, it is necessary to be able to design processes that are sufficiently low-cost to permit exploitation. One approach to minimizing the capital and operating costs for these processes is to use the capabilities of computer process simulation in the design phase of development, to make important technical and economic decisions regarding the evaluation of alternative process flow schemes, the selection of equipment and the choice of operating conditions. There are mathematical simulation models for most mineral processing operations, including several each for size reduction, size classification and mineral separations. To be able to tie these individual operating models together in an integrated mineral process simulation, however, it is important, in fact in some cases essential, that there be a model which describes how the mineral system responds to size reduction in making the liberated valuable and waste mineral particles available for concentration or rejection operations and the locked particles available for possible recirculation. This, then, is the role played by the mineral liberation model, showing the relationship between particle size, quantity and composition throughout the process.

Jan 1, 2011

By R Battison, R Duggan, S Esen, K Henley, P Dare-Bryan

Increased catch bench crest loss has been observed in recent years at Barrick’s Cowal Gold Mine situated in central New South Wales, Australia. A project was initiated to diagnose the cause of the crest loss, and evaluate ways to limit its effect on final walls.A range of different blast measurement techniques were utilised to evaluate the progressive damage caused to catch berms by presplit, production and trim blasts. Techniques employed included; single point vibration measurement, cross-hole seismic analysis, precision berm surveys, horizontal p-wave velocity measurements, crest loss volume calculation and water level changes between blasts.Blast measurements showed that the majority of damage to the catch berm was caused by the presplit blasts, which registered vibrations greater than 700 mm/s at 5 m behind the presplit line. As a result, considerable changes were made to the blast designs after a series of computer simulations via mechanistic blast modelling (MBM). The uncharged presplit collar was increased from 2 m to 4 m, and every second hole was left uncharged. Vibration modelling using a multiple seed wave (MSW) model was used to optimise trim blast delay timing. Burden relief was changed from 16 ms/m to 27 ms/m using one hole firing per 4 ms time window, and the initiation angle was changed from shallow to steep. These changes in the presplit loading and trim timing helped reduce catch bench crest loss by 1–2 m.Trim shots using a high strength bulk emulsion explosive were also identified as contributors to berm damage after analysis of blast monitoring and MBM modelling. The modelling study resulted in the generation of alternative blast designs to minimise the crest loss, including the use of low-density/low-velocity of detonation (VOD) bulk explosive product (Flexigel™ Advantage) in trim pattern designs. This was trialled on the Northern and Eastern pit walls to evaluate the damage to catch berms on final walls. The trials demonstrated that berm vibration was reduced significantly; fragmentation was similar (or slightly blockier) compared to the fragmentation using the old blast designs; displacement of the berm was reduced, so increased catch bench widths were attained. This paper summarises the trials, and presents a summary of the crest loss to date.CITATION:Battison, R, Esen, S, Duggan, R, Henley, K and Dare-Bryan, P, 2015. Reducing crest loss at Barrick Cowal Gold Mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 189–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015