Search Documents

By Albert W. Deurbrouck

This report describes the preparation characteristics of the Pittsburgh and Upper Freeport coalbeds in Hancock , Brooke , Ohio , and Marshall Counties , W. Va . Over 4.5 million tons of coal was produced in these four counties in 1962. Most of this production came from the Pittsburgh coalbed . Twelve coal samples were collected for this study , 11 from the Pittsburgh bed and 1 from the Lower Freeport bed . Two of these samples could be upgraded to produce metallurgical - grade coal . The sulfur content of the Pittsburgh- bed coals was generally excessive --as high as 4.9 percent in the raw coal and 3.19 percent in the float 1.30 specific gravity fraction . The rank of the coals in this area ranges from high-volatile A to high-volatile B bituminous .

Jan 1, 1964

The purpose of this study is to develop designs to facilitate and accelerate auger rotation stoppage (and auger rotation start up so as to promote auger disengagement during auger miner repositioning) and to provide a time delay and warning signal prior to auger start up to permit any miner s near the augers to get away from the augers before they start rotating. In the underground coal mines in the U.S., there are four auger miners that are currently in use. They are the Jeffrey 100L (see Figure 1-1) and 100M (see Figure 1-2), and the Wilcox WCM and the MK20A (see Figure 1-3).

Jan 1, 1974

By David Ballón Vera

El presente estudio describe la importancia del financiamiento en la industria minera como herramienta de difusión a través de dos condiciones: la primera, es que esta se adecúe a las características de la minería y la segunda, refiere que los mineros replanteen su estructura organizativa de estudios (pre-factibilidad,factibilidad, ingeniería y diseño) para el inicio de una posible inversión, así como preveer que de la experiencia obtenida, se contó con poco apoyo financiero.

Nov 20, 1978

By A. E. Lindquist

This Bureau of Mines publication identifies areas having sufficient coal reserves to support synthetic natural gas (SNG) development and summarizes those areas having the highest potential. Capital requirements, mining and coal cost factors, water availability, and coal-quality data pertinent to SNG production are presented. Evaluation of individual coal reserve blocks was based upon coal and water requirements of the Bureau of Mines Synthane coal gasification process.

Jan 1, 1977

By CHONG WEI, TATYANA KATSAGA, DEREK APEL

This study provides an effective determination process of the interface microstructural parameters in the numerical modelling of the mechanical interaction between two different geomaterials involved with frictional-bonded interfaces, such as the interaction between backfill columns and the surrounding rocks, or the soil-structure interaction, by using the coupled finite-difference and discrete-element (FD-DE) method. Three-dimensional numerical direct shear tests were conducted on the coupled FD-DE model of the combined rock-cemented rockfill (R-CRF) specimens with the frictional-bonded interface. With the microstructural parameters determined, the macro-mechanical properties of the interface of the coupled model were calibrated to well fit with the theoretical values of the combined specimen under the direct shear condition assumed according to the Mohr–Coulomb strength criterion. Evident elastoplastic shear behaviour was observed on the interfaces, and excellent agreement was attained between the shapes of the theoretical and simulated shear stress-displacement curves of the coupled models at different servo-controlled normal stresses. Particulate-scale force chains inside the DE model of the CRF specimen were highly consistent with the force contour on the FD model of the rock specimen, demonstrating the shear stress evolution of the coupled model at different shear displacements. Parametric studies verified the effects of the deformation properties of the interface parallel bonds on the shape of shear stress-displacement curves of the coupled models. The test results validated the feasibility and rationality of the coupled FD-DE method for modelling the combined specimens with frictional-bonded interfaces or joints. Furthermore, this study provides valuable numerical modelling experience for investigating the shear behaviour at the interface between cemented backfill columns and surrounding walls by using the coupled FD-DE method.

Nov 2, 2021

By W. Zhu

ABSTRACT: This paper presents further developments of the principle of Construction Process Mechanics of rockmasses, The principle of loading variations analyses in space-time is systematically described. To demonstrate the applicability of the theory and method, the effect of the construction process of two practical engineering cases are analysed. ZUSAMMENFASSUNG: Das Mechaniksprinzip vom Konstruktionsprozess des Massenfels wird in diesem Aufsatz weiter Entwickelt.. Das Prinzip von Variationsladungsanalyse mit dem Zeit-Raumseffekt wird systematisch erklaert. Um die Anwendungsmoeglichkeit der Theorie und der Methode zu anschaulich darstellen, das Mechanikseffekt des Konstruktionsprozess wird fuer zwei praktische Anwendungsbeispielen zergliedert. : RESUME: Dans ce papier le development se fait pour principles de la mechanique de process de construction . Le principle de variable analyse considerant effet de temps et de Space est present ´e . Pour demonstrer l´appilicabilite de le theorie et la methode , l´èffect de processe de construction pour ce deax examples sont analysés .

Jan 1, 2003

In March, the Minister of Mines, Mrs. Judy Erola, released a mineral discussion paper at the annual meeting and convention in Toronto of the Prospectors and Developers Association. Among the mineral objectives discussed was the revitalization of the "junior" mining industry. That industry reportedly has seen its share of total exploration expenditures fall from 50% in 1969 to 10% in 1979. Some sources believe the reason to be the rise of exploration costs and more- restrictive legislation The junior mining industry reportedly was responsible for 40% of all mineral discoveries in the 1969-79 period. CZECHOSLOVAKIA Czechoslovakia expects its capacity for the recovery of gallium metal to increase from 1,650 kilograms to nearly 3,000 kilograms per year by the installation of new recovery equipment at the aluminum plant at Ziar Nad Hronom in Central Slovakia. World production data are not reported, but the United States consumed 8,000 kilograms (estimated) in 1981, of which 5,536 kilograms were imported. Gallium is recovered as a byproduct of the Bayer process for the conversion of bauxite to alumina, and from certain zinc processing wastes. It is used for electronic applications such as light-emitting diodes for visual display panels in calculators, clocks, and other instruments.

Jan 1, 1982

By K Watanabe

A relational database in which its complex contents can be navigated through a map interface (ie spatially enabling) is relatively a new concept yet attractive for geoscience fields. This concept is made possible using the new breed of geographic information system (GIS) that utilises component object model and relational database management system. Such sophisticated yet open and highly interoperable platform makes possible the integration of data management, analysis, and modeling processes into single workflow. Taking benefit of this technology trend, several initiatives emerge in geoscience to establish digital data models, such as the petroleum industry, the North America digital geologic map data model, and the ESRI geology data model. The mining industry unfortunately has not followed same paths due to the lack of data model and standards in its history. This paper presents an effort on establishing a digital data model for mining-related geoscience databases. The aim is to promote several standards by proposing a preliminary data model and demonstrating that the model is working for the mining business datasets. The case study is the island of Java, the western part of the Sunda island arc of Indonesia. Many types of datasets, such as geologic maps, topography, mineral deposits, structures, geochemical and geophysical data were dealt with and were transformed relational geologic databases of Java using the new Geodatabase geographic data model. Intelligent GIS tools were investigated for geologic applications, ranging from generic to specific purposes. Subtypes and domain were used to set up constraints, while topology rules and relationship classes were used to create links among data layers. The linear referencing system was used to model drillhole data. The current results show that the generic GIS and relational database can handle typical tasks related with mining business datasets. A preliminary data model is finally suggested.

Jan 1, 2004

INTRODUCTION This paper was originally presented at the Platinum Adding Value Conference, held at Sun City from the 4th to 6th October 2004. Narrow reef mining may not be applicable to the base metal operations in Zambia, however, it is considered that the methodology used is equally appropriate to the development of technology and mining methods in mining environments other than narrow reef mining. The purpose of this paper is to explore the integration of technology and stoping systems. For the last hundred years the South African narrow reef mining industry has battled to control working costs in a labour intensive industry. It is only through the application of appropriate technology that change will occur. Stoping systems, because it is the stoping method and methodology that is at the heart of the mining system. Introduce a different technology that results in a more efficient stoping system and the mining system will look after itself. The technology applied to stoping in narrow reef mining, over the last 100 years, can be categorised as follows: ? The introduction of pneumatic rockdrills early this century. The cumbersome rig mounted units being replaced by smaller, lighter, hand held units that were then made easier to use with the addition of an air leg. (The so called Swedish method of mining.) As late as the early 1970s some drilling was still being carried out without the assistance of an air leg. ? Scraper winches to replace gravity and shovels to move rock both in the face and the gullies were first introduced in the late 1920s. ? Hydraulic props installed close to the face and capable of applying force against the hangingwall as well as yielding in a controlled manner under dynamic load arrived in the 1960s. In many instances these have now been replaced by yielding elongates fitted with water hydraulic tensioning devices. ? Some people argue that the introduction of tungsten carbide inserts, to improve drilling, was equally important.

Jan 1, 2005

By H. E. Powell

This study was made to determine the capabilities and limitations of the hydrocyclone for separating quartz sand from impure clays, Optimum operating conditions for beneficiating typical subgrade clays were determined. Estimates are furnished for installation and direct operating costs of hydrocyclones in such separations. Laboratory models of commercial hydrocyclones were used to beneficiate a suite of fire clays including plastic, semiflint, and flint types, all of which were contaminated with quartz in amounts ranging from 3 to more than 62 percent. Results show that this technique is not limited to a single type of clay but is applicable to clays ranging from plastic through flint, Under proper conditions use of this technique will result in good separation of the sand and good recovery of a useful clay mineral concentrate. Rejection of quartz from the clays investigated ranged from a low of 82.4 percent with an alumina recovery of 71.2 percent to a high of 99.0 percent with an alumina recovery of 85.6 percent.

Jan 1, 1963

The minerals industry focus over much of the past twenty years has been on cost reduction and production growth supported, but not driven, by technology improvements. Mergers and acquisitions, and the demands of financial markets, have been high priority items whereas research and development and technology based innovation have received less attention and have been cut back in many companies. Technology improvements will be critical if the industry is to make progress on the stated aims of improving energy efficiency, reducing water usage and maximising recovery from deposits. They will also be important for improving capital efficiency and in treating difficult deposits. However the role technology based innovation will play both in the overall industry, and within individual companies, during the next decade is quite uncertain. There are major challenges in progressing technology based innovation in an industry with limited technical resources which is dominated by long life high capital operations. Specific opportunities for energy and productivity improvements exist but face significant technical and structural barriers that need to be overcome if the industry is to significantly improve performance. Current evidence suggests that changes in approach will be needed for these improvements to be realised. Recent studies in the United States and Canada have highlighted the wide range of energy performance across the industry and the scope for marked improvement from both incremental improvements and increased research and development. Comminution, material transportation and underground mine ventilation were identified as high priority areas. Opportunities within these areas are discussed both in respect of specific technologies and in how they may change performance. The role of open innovation as a source of new technology is also discussed. This is an abstract only. No full paper was prepared for this presentation.

Sep 13, 2010

By Zhengjie Chen, Wenhui Ma, Jijun Wu, Kuixian Wei

The gasification reactivity of PC (petroleum coke), strengthened by addition of different potassium carbonate proportions using different grinding medium, was investigated by using thermogravimetric analysis (TGA). Results showed that the gasification reactivity of PC not only increased with the increase of catalyst-loaded, but also showed the effective improvement by anhydrous alcohol. The PC was mixed with potassium carbonate [K2CO3] catalyst at 0.5%, 0.8%, 1.0% and 1.5%, and then ground wet with distilled water. The CO2-gasification rate of PC was only 77.35%, 80.55%, 84.07% and 85.88% under the gasification temperature 1100 °C and holding time 120 min, at different K2CO3 respectively. However, when the PC was ground in anhydrous alcohol at the same condition of catalyst-loading, the gasification rate of PC reached 95.43%, 96.63%, 95.50% and 95.61% at the holding time of 108 min, 101 min, 74 min and 35 min, respectively. It was shown by FTIR, SEM and EDX determinations that the anhydrous alcohol used as the grinding medium can further improve the gasification reactivity of PC when compared with the distilled water.

Jan 1, 2016

By David L. Hill

Newmont Gold Company's Mill No. 4 is located along the Carlin trend, about 25 miles North of Carlin, Nevada. The plant consists of a primary grinding circuit using a 7.2 m (22 ft) diameter by 2.6 m (8 ft) long semi-autogenous mill along with a 2.3 m (7 ft) diameter cone crusher. Secondary grinding is performed in a 4.8 m (14.5 ft) diameter by 9.2 m (28 ft) long overflow ball mill in closed circuit with a set of 66 cm (26 in) diameter cyclones. The ground product is fed to a typical carbon-in-leach gold leach circuit. The grinding/crushing circuit operation and control scheme are the topics of this paper.

Jan 1, 1993

By A. Güngör, Ü. Atalay

Thermal treatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The assistance of thermal pretreatment prior to grinding by microwave heating is scrutinized in this study. For this purpose three copper ore samples with different chemical composition were used. To see the effect of microwave heating on ore; work index, breakage rate and breakage distribution functions of original and heat treated samples were examined. The results obtained in this study did not show significant improvement in the grindability characteristics of the studied ores with microwave heat treatment. The inadequate amount of microwave transparent matrix was the main reason for the absence of cracks and micro-fractures in the microwave heated copper samples.

Jan 1, 1999

Maps To Accompany Bulletin 418

Jan 1, 1941

By C. W. Davis

During the second year of its existence, the Ore-Testing Section has actively prosecuted work in the standardization of testing methods, in conducting routine tests and analyses for other Government agencies, and in the determination of recommended processes for the treatment of representative ores from mining districts. Close cooperation has been maintained between the members and units of this Section and those of other Sections, J. A. Woolf and J. B. Clemmer have continued to act in an advisory capacity and R. E. Head has contributed valuable assistance in the microscopic examination of ores and metallurgical products that did not respond readily to standard treatment methods.

Jan 1, 1938

By C. W. Davis

During the second year of its existence the Ore-Testing Section has actively prosecuted work in the standardization of testing methods, in conducting routine tests and analyses for other Government agencies, and in the determination of recommended processes for the treatment of representative ores from mining districts. Close cooperation has been maintained between the members and units of this Section and those of other Sections. J. A. Woolf and J, B. Clemmer have continued to act in an advisory capacity and. R. E. Head has contributed valuable assistance in the microscopic examination of ores and metallurgical products that did not respond readily to standard treatment methods.

Jan 1, 1938

By Samuel Taylor

IT is customary for the president of an engineering society, in his annual address, to describe either some engineering problem with which he has beer connected or to review the work of the society during his administration. My first thought, this being the sesquicentennial year of our nation, was to review the advance in coal mining for the past fifty years, during which period I have been more or less intimately con-nected with the bituminous coal industry, and have personally witnessed most of the great changes which have occurred in methods and machinery used in the production of coal, but preparation of the requisite address would take more time than could be spared to prepare it, and its presentation would consume so much time that it .would not be suitable. The new arrangement providing for giving the presi-dent's address at the business meeting makes it more .appropriate to review the work of the Institute during the past year, together with some suggestions which appeal to me as being of advantage to the future wel-fare of the Institute, which I will try to do briefly. The work of the business office has been reviewed in the Secretary's report and it will not be necessary for me to dwell on it. Suffice it to say, it seems to be going along very well. Additional work could be done which would be to the advantage of the Institute, if we had the money with which to defray the necessary ex-pense incident to it, but I will refer to this again later. I would be derelict if I did not refer to the splendid work of the Secretary and the Assistant Secretary. Keeping in touch with all the sections, which number now about 26, and affiliated student societies which number 40, besides special committees, and represent-ing the Institute on various boards, provides work enough to occupy the Secretary's time almost exclu-sively. In addition to this the Secretary and the As-sistant Secretary have the work of editing and publishing the TRANSACTIONS of the Institute; the issuing of the magazine, MINING AND METALLURGY, in the splendid manner in which it goes out to the mem-bership is no light task and I think they should receive the commendation of the membership for this work.

Jan 3, 1927

By M C. Goode

The use of electrical or electronic safety systems to protect personnel, and the engineering tasks associated with the design, manufacture and maintenance of these systems are referred to using the term ‘functional safety’. In the past ten years, the use of such systems has transitioned from its traditional base, in oil and gas major hazard facilities, to being a part of most large mining and materials handling projects. In particular, functional safety is rapidly becoming a significant component of Australian iron ore projects, typically in the form of emergency stops, remote isolation, drive through interlock, robot cell entry or mobile machine anti-collision systems. While these types of systems have been in use in iron ore for a long time, functional safety standards (eg AS61508, AS62061, AS4024.1503) require more rigourous demonstration of the level of risk reduction provided by the systems.The early engineering project development phases require a number of key decisions to be made around functional safety implementation. The decisions made at this point in a project will go on to dictate the required types of risk assessment and analysis, equipment selection, sizing of substations, and training and maintenance requirements for owners. For project teams that are unfamiliar with functional safety, or inexperienced in its application, an incorrect decision or failure to understand the requirements of the chosen standard can lead to a failure to meet contract requirements, as well as major cost and schedule overruns.This paper examines the implications of functional safety on early engineering studies, focusing on the following questions: How does a designer or company determine what standard is best suited to their project? What key aspects of functional safety design need to be considered during project development? And finally, how can the impact of functional safety to the project be minimised?CITATION:Goode, M C, 2017. Functional safety impacts on study stages of major projects, in Proceedings Iron Ore 2017, pp 347–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By D. J. Turk

Stillwater Mining Company’s, Nye Operation has been producing PGM concentrate since 1987.Several expansions have allowed for increasing capacity from the initial rate of 500 tons per day, to its present capacity of 3,000 tons per day. The expansions were performed with minimal impact upon production and maximum utilization of the existing equipment. The latest expansion incorporates a 6’ X 18’ SAG mill, 13’ X 20’ Ball mill, pebble crusher, rougher flotation cells, 1250 Hp tertiary grinding mill, middling and scavenger flotation cells, and cleaner column flotation cells. This paper will describe the concentrator flow sheet, and controls for improved concentrator performance.

Jan 1, 2000