Search Documents

By B. C. Craft

Oil and gas development in Mississippi during the year 1933 was rather active and a number of important wildcat wells were drilled throughout the state. Mississippi showed an increase in drilling operations during 1933. There were 58 completions from 22 counties during this period, compared with 53 completions in 10 counties during 1932. The Jackson gas field in Hinds and Rankin counties continued to be the most active area with 26 completions, resulting in 17 gas wells, 2 oil wells, and 7 dry holes, compared with 38 gas wells, 1 oil well and 5 dry holes during 1932. A further attempt to extend the producing limits of the Amory gas field resulted in a dry hole. Extensive exploration in south Mississippi has proved the existence of ample source beds and presence of an extensive sandbody near the top of Cockfield. Core tests, supplemented by extensive geophysical work, have been carried on in Jackson, George, Harrison, Pearl River and Stone counties. Exploration will be continued in 1934. The most important deep test drilled in 1933, and the deepest well ever drilled in a southeastern state, was the Eastman Gardner et al., Bank of Seminary No. 1, sec. 26-8N.-15W., Covington County. This well went through about 1300 ft. of Selma chalk, and was abandoned in the Eutaw at 8004 ft. Another interesting operation during the past year was the Foster Creek Oil Corporation's Foster Creek Lumber Co. No. 1, sec. 14-2N.-2W., in the "Eastern Conroe Trend." This test is shut down at 3687 ft. in the Catahoula sandstone and has not encountered any important shows of oil or gas. A total of 107 of the 117 gas wells completed in the Jackson gas field since its discovery in 1930 are still producing, and have a combined open flow of approximately 3,724,896,000 cu. ft. It is reasonable to assume that this area will be rather inactive during 1934 as the maximum daily production during 1933 was 3,476,000 cu. ft. The 10 wells that have gone dead were edge wells. The water level is now between the sub-sea depths of 2190 and 2195 ft. The Gulf Refining Company's Rainey No. 1, sec. 13-5N.-lE., one of the early wells in the field, had gas and water at —2225 ft. That the field is under hydraulic control is

Jan 1, 1934

By Collin Stewart

Bowie Resources, LLC (Bowie) has been using the Stability Mapping System (SMS) developed by Dr. Keith Heasley, West Virginia University, since 2005. Seven three-entry longwall gateroads, four longwall panels and a five-entry set of mains have been mined in two different seams in areas originally analyzed with the SMS. This paper compares predictions of mining conditions based on the SMS with actual mining conditions. Specific comparisons include longwall and continuous miner (CM) productivity, longwall tailgate response and support and CM roof bolting requirements. The paper also discusses current thoughts at Bowie on the use of different weighting factors for CM development, longwall face conditions and longwall tailgate support requirements.

Jan 1, 2007

By A. F. Robertson

"INTRODUCTION This report is supplemental to R.I. 4178 and deals with the work accomplished between June 15, 1945, and September 7, 1945, on the Mitchell-Hodge mine, Grady mine, Albea and York property, and Cuzzort property.ACKNOWLEDGMENTSIn its program or exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurigcal Branch, O. C. Ralston, chief, analyzes samples and performs benefication tests.Acknowledgment is due Mitchell H. Kline, chief, Raleigh Division, Mining Branch; Abraham L. Fox, acting chief, Raleigh Division, Metallurgical Branch; and Rowe McCrae, district engineers, U.S. Bureau of Mines, Gainesville,"

Jan 1, 1946

By Arthur Nomann

Recording instruments may be conveniently described under the headings of: (1) geophones, (2) amplifiers, (3) recording cameras, (4) miscellaneous parts. Geophones Geophones or seismometers are actuated by slight earth movements, and generate electrical currents, which are amplified and recorded. In all geophone desigm there is provision for differential movement between parts of the mechanism and the signal voltage is generated as a function of this differential movement. The part that conforms to the movement of the ground is called the support, and the part that remains more nearly stationary with respect to more distant unactuated parts of the earth is called the steady mass. The mechanical period of the geophone is the time required for an oscillation of the steady mass after an initial impulse is given it, and is determined by the effective stiffness of the spring joining the two parts together in relation to the weight of the suspended part. Geophones have been used with frequencies varying all the way from less than 10 cycles per sec. to several hundred cycles per second. Those with a natural frequency of less than, say, 100 cycles

Jan 1, 1940

By Arthur Nomann

Recording instruments may be conveniently described under the headings of: (1) geophones, (2) amplifiers, (3) recording cameras, (4) miscellaneous parts. Geophones Geophones or seismometers are actuated by slight earth movements, and generate electrical currents, which are amplified and recorded. In all geophone desigm there is provision for differential movement between parts of the mechanism and the signal voltage is generated as a function of this differential movement. The part that conforms to the movement of the ground is called the support, and the part that remains more nearly stationary with respect to more distant unactuated parts of the earth is called the steady mass. The mechanical period of the geophone is the time required for an oscillation of the steady mass after an initial impulse is given it, and is determined by the effective stiffness of the spring joining the two parts together in relation to the weight of the suspended part. Geophones have been used with frequencies varying all the way from less than 10 cycles per sec. to several hundred cycles per second. Those with a natural frequency of less than, say, 100 cycles

Jan 1, 1940

By C. B. Webber, W. A. Grell

"Sherritt Gordon's Ruttan Mine is a copper-zinc operation located approximately 600 miles north-west of Winnipeg. Open pit mining began in 1973 at 10,000 Tpd., with a change over to underground mining in 1981 producing 7,500 Tpd. Ore is crushed to -3/4"" followed by rod and ball mill grinding (two ball mills in series), differential copper-zinc flotation, and dewatering. The copper and zinc concentrates are trucked 75 miles to Lynn Lake, where they are shipped by rail to the HBM&S smelter at Flin Flon.This paper describes a method used to predict the effect of grind particle size on metallurgical performance, as well as details on the copper and zinc metallurgical performance due to fine grinding in actual plant operation.Initial statistical studies on historical data (including ore source, head gr3de, grind, etc.) indicated that copper and zinc recoveries increased with fineness of grind, in the range of 50 to 65% -200 mesh.In order to extrapolate beyond 65% -200 mesh, and to develop expected nonlinear relations between grind, Cu concentrate grade, and recovery, the assays of screen fractions of copper concentrate and tailing were used to determin8 the relation between net smelter return (a function of grade and recovery) and grinding cost. The optimum economic grind would be that grind at which the net smelter return less grinding cost reached a maximum."

Jan 1, 1982

In 1991, Placer Dome Venezuela established a 70% stake in Minera Las Cristinas, to mine the Las Cristinas gold deposits in Bolivar. This case study examines the multi-sectoral partnership arrangement that was developed to improve health services near the proposed Las Cristinas gold mine. The investment climate in Venezuela is uncertain and the socio-economic circumstances are potentially hostile. Despite that, the partnership between the mining company, local communities, government agencies and an international health nongovernmental organization (NGO) collectively leveraged nearly $2.5 million to build and operate a community health center.

Jan 1, 2002

By E. W. Vekris

Patents are playing an increasingly important role in the business world. A diverse patent portfolio can enable a company to secure a monopoly within the market, which can provide a competitive advantage over competitors. At the same time, possessing a diverse patent portfolio greatly increases the value of a company's intangible assets. This paper provides an overview of the patenting process as it pertains to the fields of metallurgy and mining, and summarizes some general patenting strategies. A review of new "green technology" initiatives recently adopted by Patent Offices around the world is also provided.

Jan 1, 2011

By Sayavur Bakhtiyarov

Keywords: Rheology, Viscoelastic, Oil In this paper we present the results of the rheological property measurements on viscoelastic composite materials used in oil industry. Laboratory experiments were carried out to determine important thermophysical, rheological and mechanical properties of the test materials using both the standard commercial and in-house made equipment. The composites with the paramagnetic particles (?-iron oxide) are exhibited a significant magnetic memory after magnetic treatment. The measured value of the yield stress after the magnetic treatment increased almost twice in comparison with the yield stress value of the magnetically untreated composite. The yield stress of the composite material exponentially decreases with time and reaches its magnetically untreated value after 15 hours. The yield stress also increases with the amount of the paramagnetic powder additive, and it reaches a maximum value at 8 wt-% of this additive. The obtained results provide valuable information for computer modeling of the viscoelastic fluid flow in pipes of complex geometry.

Jan 1, 2005

By Jean-François Lapointe

Many advances have been made concerning the automation of heavy equipment teleoperators such as those found in mining. Complete automation, however, is not achieved yet and the operation of these vehicles still relies on the presence of a human operator. Fortunately, a lot of research has been done in order to improve the performance of these human-machine systems. This paper presents the characteristics of different control modes and input devices used for the control interface of those telemanipulators. We describe the benefits and drawbacks of each particular control interface on the overall system performance, based on a review of research in the field. We conclude with some recommendations and a discussion of future research needs, given the new potential advances offered by virtual environment technology and embedded computing.

May 1, 2001

By S. Watkins, D. Apel, B. Gray, R. Moss

Currently, there are several techniques and technologies available which are used by mining industry in its attempts to remotely monitor the ground movements both at surface and underground mines. The currently available remote distance meters and distance change monitors mainly use phase change and time-of-flight techniques. The described monitor uses triangulation technique to track position of an optical spot projection and then image processing to measure mine wall movements. The system can be easily automated and poses no obstruction to mine traffic. The position of an off-normal laser spot will shift as the target wall moves. The described ground movement monitoring system has potential for superior accuracy and target monitoring can be made through air (gaseous) or other transparent media. The theoretical accuracy and range of this system depends solely on the resolution and focal length of the camera being used. The remote capabilities of the system make it uniquely suited to applications where monitoring is required in high-traffic, inaccessible, or unstable and dangerous areas of a mine.

Jan 1, 2007

By T. S. Bomar, C. J. Wood

Heavy media cyclones (HMCs) are efficient, high-tonnage devices suitable for upgrading run-of-mine coal in the 50 to 0.5 mm size range. Unfortunately, industrial HMC circuits are often not optimized due to problems such as incorrect operating pressures, poor feed distribution, excessive media contamination, mismatched components, and improper density control. To avoid these problems, operating guidelines have been provided in this article that are useful for optimizing the performance of HMC circuits. The validity of these guidelines has been assessed by means of density tracer tests carried out at several coal preparation plants.

Jan 1, 2002

By Gorzalczynski. Stan

The recent trend in underground mine developments is ?big is better?. This is most certainly evident in the mine shaft and the conveyances that operate within its compartments. Today, there are several new installations requiring mine cages that can transport up to 170 passengers. The technology in mine hoisting is advancing to address a combination of higher capacity requirements, deeper hoisting depths and faster winding rates, however, some areas of the hoist plant have not changed for the past fifty years. The most notable of these areas is the shaft compartment guide string and the conveyance mounted safety arrest mechanism. The technology in use today for the protection of passengers in a shaft conveyance from a hoist rope severance incident, remains conceptually unchanged from Elisha Otis? design of 1850. The actual retardation components, the safety dogs, have taken on several forms since Elisha?s invention with the last major design change occurring in the late 1940?s. The arrest of a free falling shaft conveyance requires that the shaft guides withstand the energy imparted on them by the safety dogs. There are some very real limitations presented by the use of wood for this application. The new hoisting era will most certainly continue to demand larger capacity equipment but also, an increased awareness toward safety.

May 1, 2002

By Martti Hagfors

UNDERWATER EXPLOSIONS - Part 6 - EFFCTS OF CYLINDERICAL SHAPE OF CHARGE TO THE RESULTS OF ENERGY MEASUREMENTS OF EXPLOSIVES

Jan 1, 2008

By Gary J. Cwick

Mineral resources of the Rice Valley Wilderness Study Area (WSA), in the Mojave Desert of southeastern California, were investigated by the U.S. Bureau of Mines and U.S. Geological Survey during 1980. The study consisted of an examination of mines, prospects, and mineralized areas by the Bureau: of Mines and geological, geochemical, and geophysical investigations by the Geological Survey. Little indicated potential for the presence of mineral resources exists in the valley floor segment of the study area. The Big Maria Mountains section of the study area has some potential for mineral resource development. Decorative building stone from both bedded quartzite deposits and weathered limestone surface rubble (driftwood stone) has been produced from the Big Maria Mountains segment of the study area. Total production is unrecorded but probably small. A 700,000 ton (640,000 t) quartzite resource was inferred and 4,500 tons (4,100 t) of driftwood stone within the study area was estimated. A relatively pure limestone deposit inside the study area contains an inferred resource of 14 million tons (13 million t). One prospect suggests a potential for the presence of manganese resources although none were estimated. The likelihood of discovering oil, gas, coal, uranium or geothermal energy is low; potential sources are not known to exist.

Jan 1, 1982

By Charles E. McCarthy, MORTON T. PAWEL, E. A. GEE, FRANK S. RIORDAN

Large tonnages of the magnesium silicate mineral , olivine, are known to exist in the mountains of western North Carolina and in the Puget Sound region of Washington. The North Carolina deposits alone are reputed to contain at least 230 million tons of ore averaging 45 to 49 percent of magnesium oxide In both areas the mineral is readily accessible and can be mined by the simplest methods ; one of the largest of the Washington deposits is located at tidewater .

Sep 1, 1946

By Robert M. Koerner

The feasibility of using small-scale models to simulate residential masonry foundation walls subject to fatigue loading was investigated. Five wall segments were modeled in one-quarter scale using dynamic similitude equations. The walls were dynamically loaded using a sinusoidal base motion and wall accelerations were monitored. The stiffness, natural frequency response, and damping characteristics were measured. The number of cycles of testing necessary to cause initial visible cracking was recorded. Analysis of the data indicated the importance of the relationship between the forcing function and the natural frequencies of the structure in influencing cracking damage.

Jan 1, 1980

By B. Radwanek-Bak

The assurance of future raw materials supply to the EU mineral industry has become, in recent years, one of the most important tasks of the EU Commission. It is focused on creation a new mineral policy within the EU zone. One of the starting points for this activity was identification of the mineral commodities that are critical for the sustainable development and technological progress. The paper presents the glance to this problem from the National Member level. Domestic mineral reserve base as a possible source of critical raw materials for the EU was shown. Poland cannot be considered as its resource base. The source of these raw materials are not only scarce in Poland, but also they are not produced, and their demand is now - and according to forecasts is going to be in the future - met by imports. The raw materials in question are not considered exactly critical for Polish economy, but they are of limited economic importance. On the other hand, their growth is a best opportunity and at once the need to the future sustainable development.

Jan 1, 2011

By M. Li, J. D. Miller

Many technology problems must be solved if we are to continue to produce phosphate at our current rate of consumption. The U.S. produces at least 25% of the world's phosphate, 40 million tons of phosphate rock per annum with most of the production coming from Florida. Of particular concern are improved separation efficiency and the ability to treat new dolomitic resources. Phosphate flotation technology needs include: 1. Simplification of the standard flowsheet 2. Improved recovery of coarse phosphate 3. Selective flotation for phosphate recovery from dolomitic resources Preliminary results, including tests on plant feed from Florida show that these objectives may be achieved with a new collector chemistry depending on the specific circumstances. The effectiveness of the new collector chemistry has been demonstrated by the preliminary results from single stage flotation experiments both at the University of Utah laboratories and at Florida Institute of Phosphate Research (FIPR) laboratories. In the best case, from these experiments with low grade (5% P2O5) coarse feed (16x35 mesh), a single stage phosphate recovery of 95 % was achieved with a concentrate grade of 31 % P2O5. Such a separation efficiency could not be achieved using the traditional fatty acid/fuel oil collector. Based on these results it seems that a one step process may be possible for phosphate flotation and a research program is justified for the development of this new flotation strategy.

Jan 1, 2001