Search Documents

I am wearing two hats today. When the invitations went out to participate in this forum, two were received in the head office of the Department of Lands and Survey - one addressed to the Director-General of Lands and one to the Chairman of the National Parks Authority. It seemed logical that as the department is responsible to the Government for the administration of the National Parks Act 1952, we should respond by providing one speaker to cover both the department's interests and those of the National Parks Authority. I hope, however, that this will not blur the clear distinction which exists in the context of the mineral industry between Crown land on the one hand administered by the department for the statutory Land Settlement Board and national parks and allied reserves on the other hand which are the responsibility of the National Parks Authority.

Jan 1, 1976

By Hirokazu Narita

Keywords: solvent extraction, precious metals, thiodiglycolamide, rapid separation, hydrochloric acid The solvent extraction of some precious metals (Pd(II), Pt(IV), Rh(III) and Au(III)) and base metals (Fe(III), Cu(II) and Zn(II)) in a hydrochloric acid solution was carried out using N,N'-dimethyl-N,N'-dioctyl-thiodiglycolamide (MOTDA) dissolved in the mixed solution of 80 vol-% dodecane and 20 vol-% 2-ethylhexanol. The extraction percentages of Pd(II) and Au(III) in the 0.01 M MOTDA-1.0 M HCl solution system are 99.6% and 71.8%, respectively. In contrast, the other metal ions are hardly extracted under the studied conditions. The Au(III) and Pd(II) extracted in the organic phase are easily back-extracted with a 1.0 M thiourea/1.0 M HCl solution. A comparison with the conventional extractant for the Pd(II) separation, di-n-hexyl sulfide (DHS), revealed that the extraction rate of Pd(II) with MOTDA is much greater than that with DHS. The extraction percentage reached over 99% in less than a 2 min contact time. However, in the DHS-Pd(II) system, it takes about 240 min to achieve the extraction equilibrium. Furthermore, MOTDA can quantitatively extract Pd(II) up to half the molar amount of MOTDA. Therefore, MOTDA is a promising extractant for Pd(II) from the HCl solution after the removal of Au(III).

Jan 1, 2005

By W E. Short

Ausmelt top submerged lance technology is at the cutting edge of technological developments in non-ferrous metal smelting with commercial operations throughout the world. The Technology is being used for lead smelting, copper smelting and matte converting, fuming zinc from slags, recycling iron residue from zinc plants, processing the aluminium industry hazardous waste SPL , precious metal processing, nickel-copper residue smelting and converting, and tin smelting. The Technology is also being developed for projects involving iron-making and waste industry opportunities. There are 19 furnaces operable or under design at the time of writing. The benefits to operators using Ausmelt Technology vary depending on application, but typically result from environmental improvements, enhanced recovery of valuable products, lower capital and operating costs, more flexible operations capable of handling a wide range of feed materials, better removal of impurities, or improved product quality. Growing industry acceptance of the Technology is evidenced by the fact that more than 20 per cent of the worldÆs tin production will be extracted in systems using Ausmelt Technology when the Yunnan Tin Corporation plant starts up in 2001. Metallurgists, industrialists and investors have accepted the Technology for improved operations in both greenfield main smelters and add-on plants in Korea, China, Japan, Germany, Peru, Zimbabwe, India, Namibia and Australia. Ausmelt intends that this paper will update the industry by outlining recent achievements of the Technology in global metallurgical operations.

Jan 1, 2000

By Víctor Quinzano

San Juan es una de las principales provincias exportadoras de minerales en Argentina, cuya actividad minera le proporciona mayores recursos. Sin embargo, sus plantas de fabricación (molienda, trituración) producen polvos en el exterior que contaminan el medio ambiente. Por ello, los productores incorporaron nuevas tecnologías limpias que no afecten ni el desarrollo de la producción, ni el medio ambiente. En este sentido, el presente trabajo señala las aplicaciones que el Instituto de Investigaciones Mineras de la Facultad de Ingeniería de la UNSJ ha diseñado a nivel laboratorio, a través de un recuperador electrostático de polvo, el cual responde a las necesidades de los productores y cumple con el objetivo de vinculación y transferencia con el medio productivo. Asimismo, se describe el diseño de un método de recuperación de polvos y el filtro recuperador del mismo, reduciendo el nivel de polvo a un 90% y logrando un precio de venta en el mercado.

Sep 13, 2001

By Robert P. Apa

Energy Incorporated has prepared this final report presenting the results obtained from the program for extracting alumina from anthracite culm along with the recovery of energy. This work has been accomplished under the auspices of the U.S. Bureau of Mines with technical coordination through the bureau's Reno, Nevada facility. The objective of this program was to develop a process to recover alumina and energy from Northeastern Pennsylvania anthracite mining waste. The program included Identification of sufficient resources to support a commercial facility, identification of the operating parameters which maximize alumina and energy recovery, the development of a conceptual process design, preparation of material and energy balance(s), and the performance of a system economical analysis. The program was conducted in three major phases. In the first phase the program concentrated on selecting several anthracite culm banks capable of supporting a commercial alumina producing facility. The chosen banks were then sampled and analyzed leading to the selection of two banks which were chosen far testing. The Harry E. and Eckley culm banks were the ones selected. Material from these banks was tested in Energy Incorporated?s Idaho Falls, Idaho testing facility. Parametric testing was accomplished in an eight-inch-diameter fluidized bed test facility. The test program consisted of twelve separate tests. After critical operating parameters were determined, the second phase started: process development in EI's 18-inch fluidized bed test facility. Three material and energy balance tests were completed in this facility. Following these tests a 72-hour demonstration test was performed. The data acquired from these tests were used in the last phase: the process conceptual design and economic analysis. The design basis was a commercial scale facility capable of producing 500,000 tons of alumina per year for 15 years. Based on the test program, It is technically feasible to build and operate such a plant today. The facility would produce, along with the alumina, 81.5 MWe of electricity for outside consumption. A preliminary rate of return indicates that the plant is not feasible with today's economic conditions. An increase in the market price of either the alumina or the electricity is required to provide an attractive rate of return for the facility.

Jan 1, 1982

By Paul Kunze

For some of us, the most disagreeable part of being the blaster- in - charge is doing the required paperwork. Cost coding on time cards, drilling reports, magazine inventory logs, and blast records all eat into our time. When all goes well, which I suppose is 98% of the time, the blast records are submitted and filed, probably never to be seen again. Sometimes a progressive operation will use the information documented in the blast reports to evaluate blasting effectiveness and improve results. When the report is consistently used in this fashion, costs can be reduced and other efficiencies will be realized. A blast report in times past was a simple form that mainly was used to keep track of the drill footage and of the powder used in the shot. However, as the population and consequences of careless blasting increase, multiple levels of blast documentation are now being required nearly everywhere, during all phases of the drill and blast process. We are now compelled to create preliminary blast designs prior to commencing work. We are required to submit pre-blast plans before each shot, and we need to generate post-blast reports that document the details and results of each shot.

Jan 1, 2004

By D. Pickering, R. Wharton

The deadline for meeting legal requirements relating to the sale of explosives in the European Union was 1 January 2003. The paper examines the range of materials that have already been certified by the different Explosives Notified Bodies as well as recent national and European Commission decisions relating to this work. The implications of enlargement of the European Union are also discussed as is the future role of the Great Britain Explosives Notified Body in certification and assessment.

Jan 1, 2003

By A. Atta-Quayson

Since 2012, Ghana has been implementing local procurement regulations in the mining sector to broaden and deepen linkages between mining and other sectors of the economy. The regulations have been implemented in collaboration with the mining industry. This paper offers an in-depth analysis of how the local procurement regulations and related initiatives have been implemented so far. Primary data gathered with semi-structured interviews and secondary sources of data indicate a steady improvement in both in-country procurement and local manufacturing of inputs for the mining industry. There are, however, some challenges relating to tariff structure and support (financial and technical) for local suppliers and manufacturers to meet high standards and demands of the mining industry. This calls for a well-thought-out strategy and programme of activities to sustain and improve on progress made.

Feb 2, 2022

By Murali Gadde

The immediate floor bed in the Illinois Basin coal mines is often comprised of weak plastic underclay material. Operational and stability problems were encountered in the past due to the low strength characteristics of the underclay floor. Among several indicators of the nature of the floor, Atterberg limits are the most important ones that describe the plasticity behavior of these clayey materials. While several useful and interesting studies were conducted in the past on the Illinois Basin weak floor material, within the knowledge of the authors, a comprehensive database describing the plasticity characteristics of the floor material has never been published. In this paper, a large database comprising over 700 sets of Atterberg limits was put together from 39 inactive and active mines from all the three states covering the Basin. Analysis of this data shows several interesting trends related to the engineering behavior of the floor material. The paper also describes the practical implications of the trends shown by the Atterberg limits.

Jan 1, 2008

By Vahid Tajdar

The behavior similarity between pile and cone penetration test, has guided the researchers to use the CPT results in prediction of piles bearing capacity. In this article, artificial neural networks have been used to study about relation between cone tip and sleeve friction strength obtained from cone penetration test and ultimate pile bearing capacity, obtained from static pile load test. Artificial neural networks "ANNS" is a form of artificial intelligence. ANN tries to dramatize the human nerves & brain system biology structure in self-structure. In this article, the results of relevant studies about the prediction of ultimate pile bearing capacity in especial area of soils are presented by use of back - propagation neural networks. The results of static pile load test up to failure on 63 piles with closed end and CPT test results in the place of construction these piles use in order to confirm and creation ANN model. Comparing predicted ultimate pile bearing capacity by utilizing ANN with the numbers which are predicted by 5 common traditional methods shows that using of artificial neural networks is a suitable method for predicted ultimate pile bearing capacity in identified area of texture of soil moreover it has a better operation in comparison with common traditional methods.

Jan 1, 2006

By M. Iberico

A partir de los años 70 se incrementó el proceso de exploración y desarrollo de los yacimientos mineros submarinos. En este sentido, el presente trabajo describe el origen de los depósitos a partir de los descubrimientos de módulos manganíferos en el océano pacífico que hicieron Thompson y Murray. Posteriormente Buchanam demuestra la existencia de módulos ferro-manganíferos en aguas poco profundas ( 200 m. ), de composición diferente de las provenientes de aguas profundas. De otro lado, el trabajo señala también la división de los minerales marinos en tres categorías: las sales disueltas y en organismos, los sedimentos y depósitos en el suelo profundo submarino y los depósitos consolidados e inconsolidados de la plataforma continental. Por último, se describe los procesos de beneficio y las ventajas de la explotación de los recursos submarinos en el futuro de la minería submarina.

Nov 20, 1972

By P. Roghanchi

The Rock Mass Rating (RMR) system is an internationally recognized classification system that can be used for preliminary ground control design. The RMR system assigns quantifiable values to predefined classified parameters of a rock mass. Assigning a single value rather than a range to each parameter is a source of uncertainty, however, assigning a single value can be useful for further studies related to RMR ratings. Fuzzy systems are being used in an increasing number of application areas where linguistic rules are used to describe the system. In past decades, fuzzy systems have been successfully used in geotechnical and mining engineering problems to cope with uncertain data as well as with vagueness. In such scenarios, linguistic rules and rating-based classification of rock masses have always been questionable. The objective of this study is to apply fuzzy set theory to the RMR classification system. The fuzzy system proposed in this study is specified for weak and very weak rock masses (RMR<50) based on data collected from Nevada gold mines where 68% of RMR data is in the ?poor? and ?very poor? classes. In this approach, a Mamdani fuzzy algorithm has been constructed to evaluate basic RMR89 rating for the ?wet condition.? Comparison between basic RMR89 and fuzzy RMR shows the fuzzy RMR system is valid to predict RMR from the discrete rating of each input parameter.

Feb 27, 2013

By H. Ewaschuk

"INTRODUCTIONRio Algom's involvement with the Enviro-Clear thickener began in May 1975, when tests on a laboratory waif were carried out by our Research and Development group. Commencing in June, further tests were carried out using a 3 foot diameter pilot unit. By December, a 30 foot full-scale thickener had been installed. In the near future, 3 more Enviro-Clear thickeners will be commissioned. With in the space of a year, almost $2.5 million had been committed to liquid/ solid separation facilities using the Enviro-Clear thickener. This paper briefly traces the extent and development of this commitment.BRIEF HISTORY OF QUIRKEQuirke Mine started operating in September 1956 at a rated capacity of 3,000 TOD. Because of market conditions, Quirke was shut down in December 1960. The facilities were re-opened at an increased capacity of 4,000 TPD in July 1968, by which time the demand for uranium had returned. Also, a second shaft was sunk, and by 1970, all of the ore treated in the concentrator was coming from the new Quirke II mine. The Quirke I stopes were allowed to fill with natural seepage. As well, acidic barren solution from the concentrator was pumped underground.With increasing demand for uranium, the capacity of Quirke will be further expanded to 7,000 TPD by 1978. Studies of how this expansion could best he carried out led to the consideration of a fairly new piece of equipment, the Enviro-Clear thickener, for certain operations in the concentrator. These operations are as follows:"

Jan 1, 1977

The typical reactions which the reductants undergo during ferroalloy production are reviewed, and identified as reaction with CO2 and with SiO, and dissolution in metal. Available reactivity tests for these three reactions are reviewed. It is proposed that it is worthwhile considering dissolution kinetics as a reactivity parameter. Greater crystallinity of the reductant decreases CO2 and SiO reactivity, but increases dissolution rates.

Jan 1, 2002

By J. Engelbrecht

South Africa?s re-entry into the fast moving and competitive global economy calls for some careful strategic planning and a good deal of co-operation between suppliers and end-users. The issues that need addressing are generally well known and include: ?South Africa was ranked 45th out of 46 i.r.o. productivity ?SMMEs contribute 1% to exports compared to 40-60% for the ?tigers? ?High unemployment ?Limited skills of the majority of workers ?Slow growth rate of the economy ?The vast majority of suppliers are not world-class ?The vast majority of suppliers are not export or marketing orientated. In order to survive, all parties, i.e. government, labour and business, will have to play their part.

Jan 1, 1999

By G. H. Hope

"Pamour Porcupine Mines of Timmins, Ontario operates two 3,000 ton per day concentrators which receive ore from eight to ten mines in the area. The area milling concept was adopted by Pamour in 1971 and has been used successfully since then. The purpose of this paper is to discuss the advantages and the problems of area milling. Pamour Porcupine Mines Limited operates two 3,000 ton per day concentrators which receive ore from eight to ten mines in the Porcupine region. The area milling concept was adopted as the route to survival for Pamour and has worked successfully. HISTORICAL BACKGROUNDProduction of gold from the Porcupine region in Northern Ontario started in the early 1900's and has been continuous since that time. Some of the major operators were companies such as Mcintyre, Hollinger, Dome, Pamour, Paymaster and the list goes on. An underground survey would reveal hundreds of miles of drifts and raises. The main group of mines extends from South East of Timmins to the Pamour Mine, 15 miles to the east. During the lean years of the sixties when gold prices were low, labour costs were rising rapidly, and ore grades were dropping, many of the area mines closed down their operations."

Jan 1, 1981

Mechanism of Modified Sodium Silicate on Fluorite Ore Flotation

Sep 13, 2010

By Andre Balt, Pierre Hofmeyr

It is only recently that automation has been applied to mining analytical laboratories. This paper describes the use of automation in the laboratory analytical process of hard-rock mining and geological samples and slurries in mining concentrator plant process control laboratories. Types of analysis include fire assay, XRF, ICP and wet chemistry. The benefits of automation are reduced unit cost of analyses, greatly reduced staff requirements, higher quality of data and very fast turn-around times.

Jan 1, 2005

By Norman Disley, David B. Counter, Lionel Hebert

Misfires in underground and surface production blasts can be costly. Costs can arise from loss of resource, production interruptions, having to redrill or otherwise refire the blast (a hazardous process at best), due to added secondary blasting or breakage, and/or from increased LHD maintenance costs attributable to poor fragmentation.

Jan 1, 1996

Efficiency, Economics, Energy and Emissions - Emerging Criteria for Comminution Circuit Decision Making

Sep 13, 2010